From: Heiko Stuebner <heiko.stuebner@cherry.de>

The jaguar has an hdmi output port, which is connected
to the hdmi0 controller of the rk3588.

Add the necessary plumbing to enable it using the recently merged
hdmi-qp controller.

Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
---
 .../arm64/boot/dts/rockchip/rk3588-jaguar.dts | 50 +++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts b/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts
index e24da1a4331d..6a59887979ce 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588-jaguar.dts
@@ -8,6 +8,7 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
 #include <dt-bindings/usb/pd.h>
 #include "rk3588.dtsi"
 
@@ -58,6 +59,17 @@ emmc_pwrseq: emmc-pwrseq {
 		reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>;
 	};
 
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi0_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -271,6 +283,29 @@ &gpu {
 	status = "okay";
 };
 
+&hdmi0 {
+	/* No CEC on Jaguar */
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmim0_tx0_hpd &hdmim0_tx0_scl &hdmim0_tx0_sda>;
+	status = "okay";
+};
+
+&hdmi0_in {
+	hdmi0_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi0>;
+	};
+};
+
+&hdmi0_out {
+	hdmi0_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdptxphy_hdmi0 {
+	status = "okay";
+};
+
 &i2c0 {
 	pinctrl-0 = <&i2c0m2_xfer>;
 	status = "okay";
@@ -1052,3 +1087,18 @@ &usb_host1_ehci {
 &usb_host1_ohci {
 	status = "okay";
 };
+
+&vop {
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi0_in_vp0>;
+	};
+};
-- 
2.45.2

Hi Heiko,

On 10/24/24 5:14 PM, Heiko Stuebner wrote:
> From: Heiko Stuebner <heiko.stuebner@cherry.de>
> 
> The jaguar has an hdmi output port, which is connected
> to the hdmi0 controller of the rk3588.
> 
> Add the necessary plumbing to enable it using the recently merged
> hdmi-qp controller.
> 
> Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>

I have this Chinese portable HDMI display[1] which doesn't print 
anything at boot but works with modetest. Same behavior can be observed 
on downstream, maybe we can get some people interested in debugging this 
now that it also impacts upstream :)

With a decent, FHD, monitor everything is fine so:

Tested-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>

Thanks!
Quentin

[1] https://www.amazon.de/dp/B0CKYR6FN5