From: mjchen <mjchen@nuvoton.com>
Adds a new keypad driver for the MA35D1 platform.
The driver supports key scanning and interrupt handling.
Signed-off-by: mjchen <mjchen@nuvoton.com>
---
drivers/input/keyboard/Kconfig | 10 +
drivers/input/keyboard/Makefile | 1 +
drivers/input/keyboard/ma35d1_keypad.c | 312 +++++++++++++++++++++++++
3 files changed, 323 insertions(+)
create mode 100644 drivers/input/keyboard/ma35d1_keypad.c
diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index 721ab69e84ac..ce9bd5cc13a1 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -797,4 +797,14 @@ config KEYBOARD_CYPRESS_SF
To compile this driver as a module, choose M here: the
module will be called cypress-sf.
+config KEYBOARD_MA35D1
+ tristate "Nuvoton MA35D1 keypad driver"
+ depends on ARCH_MA35
+ select INPUT_MATRIXKMAP
+ help
+ Say Y here if you want to use Nuvoton MA35D1 keypad.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ma35d1-keypad.
+
endif
diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
index 1e0721c30709..9b858cdd1b6b 100644
--- a/drivers/input/keyboard/Makefile
+++ b/drivers/input/keyboard/Makefile
@@ -70,3 +70,4 @@ obj-$(CONFIG_KEYBOARD_TEGRA) += tegra-kbc.o
obj-$(CONFIG_KEYBOARD_TM2_TOUCHKEY) += tm2-touchkey.o
obj-$(CONFIG_KEYBOARD_TWL4030) += twl4030_keypad.o
obj-$(CONFIG_KEYBOARD_XTKBD) += xtkbd.o
+obj-$(CONFIG_KEYBOARD_MA35D1) += ma35d1_keypad.o
diff --git a/drivers/input/keyboard/ma35d1_keypad.c b/drivers/input/keyboard/ma35d1_keypad.c
new file mode 100644
index 000000000000..20b5b1b91127
--- /dev/null
+++ b/drivers/input/keyboard/ma35d1_keypad.c
@@ -0,0 +1,312 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * MA35D1 keypad driver
+ * Copyright (C) 2024 Nuvoton Technology Corp.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/platform_device.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+
+/* Keypad Interface Registers */
+#define KPI_CONF 0x00
+#define KPI_3KCONF 0x04
+#define KPI_STATUS 0x08
+#define KPI_RSTC 0x0C
+#define KPI_KEST 0x10
+#define KPI_KPE0 0x18
+#define KPI_KPE1 0x1C
+#define KPI_KRE0 0x20
+#define KPI_KRE1 0x24
+#define KPI_PRESCALDIV 0x28
+
+/* KPI_CONF - Keypad Configuration Register */
+#define KROW GENMASK(30, 28) /* Keypad Matrix ROW number */
+#define KCOL GENMASK(26, 24) /* Keypad Matrix COL Number */
+#define DB_CLKSEL GENMASK(19, 16) /* De-bounce sampling cycle selection */
+#define PRESCALE GENMASK(15, 8) /* Row Scan Cycle Pre-scale Value */
+#define WAKEUP BIT(5) /* Lower Power Wakeup Enable */
+#define INTEN BIT(3) /* Key Interrupt Enable Control */
+#define RKINTEN BIT(2) /* Release Key Interrupt Enable */
+#define PKINTEN BIT(1) /* Press Key Interrupt Enable Control */
+#define ENKP BIT(0) /* Keypad Scan Enable */
+
+/* KPI_STATUS - Keypad Status Register */
+#define PKEY_INT BIT(4) /* Press key interrupt */
+#define RKEY_INT BIT(3) /* Release key interrupt */
+#define KEY_INT BIT(2) /* Key Interrupt */
+#define RST_3KEY BIT(1) /* 3-Keys Reset Flag */
+#define PDWAKE BIT(0) /* Power Down Wakeup Flag */
+
+#define DEFAULT_DEBOUNCE 1
+#define DEFAULT_PRE_SCALE 1
+#define DEFAULT_PRE_SCALEDIV 32
+
+struct ma35d1_keypad {
+ struct clk *clk;
+ struct input_dev *input_dev;
+ void __iomem *mmio_base;
+ int irq;
+ unsigned int kpi_row;
+ unsigned int kpi_col;
+ unsigned int debounce_val;
+ unsigned int pre_scale;
+ unsigned int pre_scale_divider;
+};
+
+static void ma35d1_keypad_scan_matrix(struct ma35d1_keypad *keypad, unsigned int status)
+{
+ struct input_dev *input_dev = keypad->input_dev;
+ unsigned int i, j;
+ unsigned int row_add = 0;
+ unsigned int code;
+ unsigned int key;
+ unsigned int press_key;
+ unsigned long KeyEvent[4];
+ unsigned int row_shift = get_count_order(keypad->kpi_col);
+ unsigned short *keymap = input_dev->keycode;
+
+ /* Read key event status */
+ KeyEvent[0] = readl(keypad->mmio_base + KPI_KPE0);
+ KeyEvent[1] = readl(keypad->mmio_base + KPI_KPE1);
+ KeyEvent[2] = readl(keypad->mmio_base + KPI_KRE0);
+ KeyEvent[3] = readl(keypad->mmio_base + KPI_KRE1);
+
+ /* Clear key event status */
+ writel(KeyEvent[0], (keypad->mmio_base + KPI_KPE0));
+ writel(KeyEvent[1], (keypad->mmio_base + KPI_KPE1));
+ writel(KeyEvent[2], (keypad->mmio_base + KPI_KRE0));
+ writel(KeyEvent[3], (keypad->mmio_base + KPI_KRE1));
+
+ for (j = 0; j < 4; j++) {
+ if (KeyEvent[j] != 0) {
+ row_add = (j % 2) ? 4 : 0;
+ press_key = (j < 2) ? 1 : 0;
+
+ for (i = 0; i < 32; i++) {
+ if (KeyEvent[j] & (1<<i)) {
+ code = MATRIX_SCAN_CODE(((i/8) + row_add), (i % 8), row_shift);
+ key = keymap[code];
+
+ input_event(input_dev, EV_MSC, MSC_SCAN, code);
+ input_report_key(input_dev, key, press_key);
+ }
+ }
+ }
+ }
+
+ input_sync(input_dev);
+}
+
+static irqreturn_t ma35d1_keypad_interrupt(int irq, void *dev_id)
+{
+ struct ma35d1_keypad *keypad = dev_id;
+ unsigned int kstatus;
+
+ kstatus = readl(keypad->mmio_base + KPI_STATUS);
+
+ if (kstatus & (PKEY_INT|RKEY_INT)) {
+ ma35d1_keypad_scan_matrix(keypad, kstatus);
+ } else {
+ if (kstatus & PDWAKE)
+ writel(PDWAKE, (keypad->mmio_base + KPI_STATUS));
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int ma35d1_keypad_open(struct input_dev *dev)
+{
+ struct ma35d1_keypad *keypad = input_get_drvdata(dev);
+ unsigned int val, config;
+
+ val = RKINTEN | PKINTEN | INTEN | ENKP;
+ val |= FIELD_PREP(KCOL, (keypad->kpi_col - 1)) | FIELD_PREP(KROW, (keypad->kpi_row - 1));
+
+ if (keypad->debounce_val > 0)
+ config = FIELD_PREP(PRESCALE, (keypad->pre_scale - 1)) |
+ FIELD_PREP(DB_CLKSEL, keypad->debounce_val);
+ else
+ config = FIELD_PREP(PRESCALE, (keypad->pre_scale - 1));
+
+ val |= config;
+
+ writel(val, keypad->mmio_base + KPI_CONF);
+ writel((keypad->pre_scale_divider - 1), keypad->mmio_base + KPI_PRESCALDIV);
+
+ return 0;
+}
+
+static void ma35d1_keypad_close(struct input_dev *dev)
+{
+ struct ma35d1_keypad *keypad = input_get_drvdata(dev);
+
+ clk_disable(keypad->clk);
+}
+
+static int ma35d1_keypad_probe(struct platform_device *pdev)
+{
+ struct ma35d1_keypad *keypad;
+ struct input_dev *input_dev;
+ struct resource *res;
+ int error = 0;
+
+ keypad = devm_kzalloc(&pdev->dev, sizeof(*keypad), GFP_KERNEL);
+ if (!keypad)
+ return -ENOMEM;
+
+
+ input_dev = input_allocate_device();
+ if (!input_dev) {
+ dev_err(&pdev->dev, "failed to allocate input device\n");
+ return -ENOMEM;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "failed to get I/O memory\n");
+ error = -ENXIO;
+ goto failed_free_input;
+ }
+
+ keypad->mmio_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(keypad->mmio_base)) {
+ dev_err(&pdev->dev, "failed to remap I/O memory\n");
+ return PTR_ERR(keypad->mmio_base);
+ }
+
+ keypad->irq = platform_get_irq(pdev, 0);
+ if (keypad->irq < 0) {
+ dev_err(&pdev->dev, "failed to get IRQ\n");
+ return keypad->irq;
+ }
+
+ keypad->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(keypad->clk)) {
+ dev_err(&pdev->dev, "failed to get core clk: %ld\n", PTR_ERR(keypad->clk));
+ return PTR_ERR(keypad->clk);
+ }
+
+ error = matrix_keypad_parse_properties(&pdev->dev,
+ &(keypad->kpi_row),
+ &(keypad->kpi_col));
+ if (error) {
+ dev_err(&pdev->dev, "failed to parse kp params\n");
+ return error;
+ }
+
+ error = matrix_keypad_build_keymap(NULL, NULL,
+ keypad->kpi_row,
+ keypad->kpi_col,
+ NULL, input_dev);
+ if (error) {
+ dev_err(&pdev->dev, "failed to build keymap\n");
+ return error;
+ }
+
+ keypad->input_dev = input_dev;
+ input_dev->name = pdev->name;
+ input_dev->id.bustype = BUS_HOST;
+ input_dev->open = ma35d1_keypad_open;
+ input_dev->close = ma35d1_keypad_close;
+ input_dev->dev.parent = &pdev->dev;
+
+ if (of_property_read_u32(pdev->dev.of_node, "debounce-period", &(keypad->debounce_val)))
+ keypad->debounce_val = DEFAULT_DEBOUNCE;
+
+ if (of_property_read_u32(pdev->dev.of_node, "per-scale", &(keypad->pre_scale)))
+ keypad->pre_scale = DEFAULT_PRE_SCALE;
+
+ if (of_property_read_u32(pdev->dev.of_node, "per-scalediv", &(keypad->pre_scale_divider)))
+ keypad->pre_scale_divider = DEFAULT_PRE_SCALEDIV;
+
+ __set_bit(EV_REP, input_dev->evbit);
+ input_set_drvdata(input_dev, keypad);
+ input_set_capability(input_dev, EV_MSC, MSC_SCAN);
+
+ error = input_register_device(input_dev);
+ if (error) {
+ dev_err(&pdev->dev, "failed to register input device\n");
+ goto failed_free_input;
+ }
+
+ error = devm_request_irq(&pdev->dev, keypad->irq,
+ ma35d1_keypad_interrupt,
+ IRQF_NO_SUSPEND, pdev->name, keypad);
+ if (error) {
+ dev_err(&pdev->dev, "failed to request IRQ\n");
+ goto failed_unregister_input;
+ }
+
+ platform_set_drvdata(pdev, keypad);
+ device_init_wakeup(&pdev->dev, 1);
+ clk_prepare_enable(keypad->clk);
+
+ return 0;
+
+failed_unregister_input:
+ input_unregister_device(input_dev);
+failed_free_input:
+ input_free_device(input_dev);
+ return error;
+}
+
+static void ma35d1_keypad_remove(struct platform_device *pdev)
+{
+ struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
+
+ input_unregister_device(keypad->input_dev);
+ clk_disable_unprepare(keypad->clk);
+}
+
+static int ma35d1_keypad_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
+
+ if (device_may_wakeup(&pdev->dev)) {
+ writel(readl(keypad->mmio_base + KPI_CONF) | WAKEUP, keypad->mmio_base + KPI_CONF);
+ enable_irq_wake(keypad->irq);
+ }
+
+ return 0;
+}
+
+static int ma35d1_keypad_resume(struct platform_device *pdev)
+{
+ struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
+
+ if (device_may_wakeup(&pdev->dev)) {
+ writel(readl(keypad->mmio_base + KPI_CONF) & ~(WAKEUP),
+ keypad->mmio_base + KPI_CONF);
+ disable_irq_wake(keypad->irq);
+ }
+
+ return 0;
+}
+
+static const struct of_device_id ma35d1_kpi_of_match[] = {
+ { .compatible = "nuvoton,ma35d1-kpi"},
+ {},
+};
+MODULE_DEVICE_TABLE(of, ma35d1_kpi_of_match);
+
+static struct platform_driver ma35d1_keypad_driver = {
+ .probe = ma35d1_keypad_probe,
+ .remove = ma35d1_keypad_remove,
+ .suspend = ma35d1_keypad_suspend,
+ .resume = ma35d1_keypad_resume,
+ .driver = {
+ .name = "ma35d1-kpi",
+ .of_match_table = of_match_ptr(ma35d1_kpi_of_match),
+ },
+};
+module_platform_driver(ma35d1_keypad_driver);
+
+MODULE_AUTHOR("Ming-Jen Chen");
+MODULE_DESCRIPTION("MA35D1 Keypad Driver");
+MODULE_LICENSE("GPL");
+
--
2.17.1Hi,
On Tue, Oct 22, 2024 at 06:31:58AM +0000, mjchen wrote:
> From: mjchen <mjchen@nuvoton.com>
>
> Adds a new keypad driver for the MA35D1 platform.
> The driver supports key scanning and interrupt handling.
>
> Signed-off-by: mjchen <mjchen@nuvoton.com>
> ---
> drivers/input/keyboard/Kconfig | 10 +
> drivers/input/keyboard/Makefile | 1 +
> drivers/input/keyboard/ma35d1_keypad.c | 312 +++++++++++++++++++++++++
> 3 files changed, 323 insertions(+)
> create mode 100644 drivers/input/keyboard/ma35d1_keypad.c
>
> diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
> index 721ab69e84ac..ce9bd5cc13a1 100644
> --- a/drivers/input/keyboard/Kconfig
> +++ b/drivers/input/keyboard/Kconfig
> @@ -797,4 +797,14 @@ config KEYBOARD_CYPRESS_SF
> To compile this driver as a module, choose M here: the
> module will be called cypress-sf.
>
> +config KEYBOARD_MA35D1
> + tristate "Nuvoton MA35D1 keypad driver"
> + depends on ARCH_MA35
> + select INPUT_MATRIXKMAP
> + help
> + Say Y here if you want to use Nuvoton MA35D1 keypad.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called ma35d1-keypad.
> +
> endif
> diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
> index 1e0721c30709..9b858cdd1b6b 100644
> --- a/drivers/input/keyboard/Makefile
> +++ b/drivers/input/keyboard/Makefile
> @@ -70,3 +70,4 @@ obj-$(CONFIG_KEYBOARD_TEGRA) += tegra-kbc.o
> obj-$(CONFIG_KEYBOARD_TM2_TOUCHKEY) += tm2-touchkey.o
> obj-$(CONFIG_KEYBOARD_TWL4030) += twl4030_keypad.o
> obj-$(CONFIG_KEYBOARD_XTKBD) += xtkbd.o
> +obj-$(CONFIG_KEYBOARD_MA35D1) += ma35d1_keypad.o
> diff --git a/drivers/input/keyboard/ma35d1_keypad.c b/drivers/input/keyboard/ma35d1_keypad.c
> new file mode 100644
> index 000000000000..20b5b1b91127
> --- /dev/null
> +++ b/drivers/input/keyboard/ma35d1_keypad.c
> @@ -0,0 +1,312 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * MA35D1 keypad driver
> + * Copyright (C) 2024 Nuvoton Technology Corp.
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/input.h>
> +#include <linux/platform_device.h>
> +#include <linux/input/matrix_keypad.h>
> +#include <linux/clk.h>
> +#include <linux/of.h>
> +
> +/* Keypad Interface Registers */
> +#define KPI_CONF 0x00
> +#define KPI_3KCONF 0x04
> +#define KPI_STATUS 0x08
> +#define KPI_RSTC 0x0C
> +#define KPI_KEST 0x10
> +#define KPI_KPE0 0x18
> +#define KPI_KPE1 0x1C
> +#define KPI_KRE0 0x20
> +#define KPI_KRE1 0x24
> +#define KPI_PRESCALDIV 0x28
> +
> +/* KPI_CONF - Keypad Configuration Register */
> +#define KROW GENMASK(30, 28) /* Keypad Matrix ROW number */
> +#define KCOL GENMASK(26, 24) /* Keypad Matrix COL Number */
> +#define DB_CLKSEL GENMASK(19, 16) /* De-bounce sampling cycle selection */
> +#define PRESCALE GENMASK(15, 8) /* Row Scan Cycle Pre-scale Value */
> +#define WAKEUP BIT(5) /* Lower Power Wakeup Enable */
> +#define INTEN BIT(3) /* Key Interrupt Enable Control */
> +#define RKINTEN BIT(2) /* Release Key Interrupt Enable */
> +#define PKINTEN BIT(1) /* Press Key Interrupt Enable Control */
> +#define ENKP BIT(0) /* Keypad Scan Enable */
> +
> +/* KPI_STATUS - Keypad Status Register */
> +#define PKEY_INT BIT(4) /* Press key interrupt */
> +#define RKEY_INT BIT(3) /* Release key interrupt */
> +#define KEY_INT BIT(2) /* Key Interrupt */
> +#define RST_3KEY BIT(1) /* 3-Keys Reset Flag */
> +#define PDWAKE BIT(0) /* Power Down Wakeup Flag */
> +
> +#define DEFAULT_DEBOUNCE 1
> +#define DEFAULT_PRE_SCALE 1
> +#define DEFAULT_PRE_SCALEDIV 32
> +
> +struct ma35d1_keypad {
> + struct clk *clk;
> + struct input_dev *input_dev;
> + void __iomem *mmio_base;
> + int irq;
> + unsigned int kpi_row;
> + unsigned int kpi_col;
> + unsigned int debounce_val;
> + unsigned int pre_scale;
> + unsigned int pre_scale_divider;
> +};
> +
> +static void ma35d1_keypad_scan_matrix(struct ma35d1_keypad *keypad, unsigned int status)
> +{
> + struct input_dev *input_dev = keypad->input_dev;
> + unsigned int i, j;
> + unsigned int row_add = 0;
> + unsigned int code;
> + unsigned int key;
> + unsigned int press_key;
> + unsigned long KeyEvent[4];
No camel-casing please.
> + unsigned int row_shift = get_count_order(keypad->kpi_col);
> + unsigned short *keymap = input_dev->keycode;
> +
> + /* Read key event status */
> + KeyEvent[0] = readl(keypad->mmio_base + KPI_KPE0);
> + KeyEvent[1] = readl(keypad->mmio_base + KPI_KPE1);
> + KeyEvent[2] = readl(keypad->mmio_base + KPI_KRE0);
> + KeyEvent[3] = readl(keypad->mmio_base + KPI_KRE1);
> +
> + /* Clear key event status */
> + writel(KeyEvent[0], (keypad->mmio_base + KPI_KPE0));
> + writel(KeyEvent[1], (keypad->mmio_base + KPI_KPE1));
> + writel(KeyEvent[2], (keypad->mmio_base + KPI_KRE0));
> + writel(KeyEvent[3], (keypad->mmio_base + KPI_KRE1));
> +
> + for (j = 0; j < 4; j++) {
> + if (KeyEvent[j] != 0) {
> + row_add = (j % 2) ? 4 : 0;
> + press_key = (j < 2) ? 1 : 0;
So you have first 64 bits to indicate pressed keys, followed by 64 bits
of released keys, right?
I wonder if you could declare 2 bitmaps of 64 bits and then used
for_each_set_bit() for each of them.
> +
> + for (i = 0; i < 32; i++) {
> + if (KeyEvent[j] & (1<<i)) {
> + code = MATRIX_SCAN_CODE(((i/8) + row_add), (i % 8), row_shift);
> + key = keymap[code];
> +
> + input_event(input_dev, EV_MSC, MSC_SCAN, code);
> + input_report_key(input_dev, key, press_key);
> + }
> + }
> + }
> + }
> +
> + input_sync(input_dev);
> +}
> +
> +static irqreturn_t ma35d1_keypad_interrupt(int irq, void *dev_id)
> +{
> + struct ma35d1_keypad *keypad = dev_id;
> + unsigned int kstatus;
> +
> + kstatus = readl(keypad->mmio_base + KPI_STATUS);
> +
> + if (kstatus & (PKEY_INT|RKEY_INT)) {
> + ma35d1_keypad_scan_matrix(keypad, kstatus);
> + } else {
Is this really "else"? Can it be that all 3 bits will be set?
> + if (kstatus & PDWAKE)
> + writel(PDWAKE, (keypad->mmio_base + KPI_STATUS));
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int ma35d1_keypad_open(struct input_dev *dev)
> +{
> + struct ma35d1_keypad *keypad = input_get_drvdata(dev);
> + unsigned int val, config;
> +
> + val = RKINTEN | PKINTEN | INTEN | ENKP;
> + val |= FIELD_PREP(KCOL, (keypad->kpi_col - 1)) | FIELD_PREP(KROW, (keypad->kpi_row - 1));
> +
> + if (keypad->debounce_val > 0)
> + config = FIELD_PREP(PRESCALE, (keypad->pre_scale - 1)) |
> + FIELD_PREP(DB_CLKSEL, keypad->debounce_val);
> + else
> + config = FIELD_PREP(PRESCALE, (keypad->pre_scale - 1));
> +
> + val |= config;
> +
> + writel(val, keypad->mmio_base + KPI_CONF);
> + writel((keypad->pre_scale_divider - 1), keypad->mmio_base + KPI_PRESCALDIV);
> +
> + return 0;
> +}
> +
> +static void ma35d1_keypad_close(struct input_dev *dev)
> +{
> + struct ma35d1_keypad *keypad = input_get_drvdata(dev);
> +
> + clk_disable(keypad->clk);
This is broken. What will happen if you open and close the device twice?
If you disable the clock in close() you need to enable it in open().
> +}
> +
> +static int ma35d1_keypad_probe(struct platform_device *pdev)
> +{
> + struct ma35d1_keypad *keypad;
> + struct input_dev *input_dev;
> + struct resource *res;
> + int error = 0;
> +
> + keypad = devm_kzalloc(&pdev->dev, sizeof(*keypad), GFP_KERNEL);
> + if (!keypad)
> + return -ENOMEM;
> +
> +
> + input_dev = input_allocate_device();
devm_input_allocate_device().
> + if (!input_dev) {
> + dev_err(&pdev->dev, "failed to allocate input device\n");
> + return -ENOMEM;
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res) {
> + dev_err(&pdev->dev, "failed to get I/O memory\n");
> + error = -ENXIO;
> + goto failed_free_input;
> + }
> +
> + keypad->mmio_base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(keypad->mmio_base)) {
> + dev_err(&pdev->dev, "failed to remap I/O memory\n");
> + return PTR_ERR(keypad->mmio_base);
Leaking input device (but OK if you switch to devm for it).
> + }
> +
> + keypad->irq = platform_get_irq(pdev, 0);
> + if (keypad->irq < 0) {
> + dev_err(&pdev->dev, "failed to get IRQ\n");
> + return keypad->irq;
> + }
> +
> + keypad->clk = devm_clk_get(&pdev->dev, NULL);
> + if (IS_ERR(keypad->clk)) {
> + dev_err(&pdev->dev, "failed to get core clk: %ld\n", PTR_ERR(keypad->clk));
> + return PTR_ERR(keypad->clk);
> + }
> +
> + error = matrix_keypad_parse_properties(&pdev->dev,
> + &(keypad->kpi_row),
> + &(keypad->kpi_col));
What tab stop are you using?
> + if (error) {
> + dev_err(&pdev->dev, "failed to parse kp params\n");
> + return error;
> + }
> +
> + error = matrix_keypad_build_keymap(NULL, NULL,
> + keypad->kpi_row,
> + keypad->kpi_col,
> + NULL, input_dev);
> + if (error) {
> + dev_err(&pdev->dev, "failed to build keymap\n");
> + return error;
> + }
> +
> + keypad->input_dev = input_dev;
> + input_dev->name = pdev->name;
> + input_dev->id.bustype = BUS_HOST;
> + input_dev->open = ma35d1_keypad_open;
> + input_dev->close = ma35d1_keypad_close;
> + input_dev->dev.parent = &pdev->dev;
> +
> + if (of_property_read_u32(pdev->dev.of_node, "debounce-period", &(keypad->debounce_val)))
> + keypad->debounce_val = DEFAULT_DEBOUNCE;
Please use generic device property API (device_property_read_u32() and
others).
> +
> + if (of_property_read_u32(pdev->dev.of_node, "per-scale", &(keypad->pre_scale)))
> + keypad->pre_scale = DEFAULT_PRE_SCALE;
> +
> + if (of_property_read_u32(pdev->dev.of_node, "per-scalediv", &(keypad->pre_scale_divider)))
> + keypad->pre_scale_divider = DEFAULT_PRE_SCALEDIV;
> +
> + __set_bit(EV_REP, input_dev->evbit);
> + input_set_drvdata(input_dev, keypad);
> + input_set_capability(input_dev, EV_MSC, MSC_SCAN);
> +
> + error = input_register_device(input_dev);
> + if (error) {
> + dev_err(&pdev->dev, "failed to register input device\n");
> + goto failed_free_input;
> + }
> +
> + error = devm_request_irq(&pdev->dev, keypad->irq,
> + ma35d1_keypad_interrupt,
> + IRQF_NO_SUSPEND, pdev->name, keypad);
Why IRQF_NO_SUSPEND?
> + if (error) {
> + dev_err(&pdev->dev, "failed to request IRQ\n");
> + goto failed_unregister_input;
> + }
> +
> + platform_set_drvdata(pdev, keypad);
> + device_init_wakeup(&pdev->dev, 1);
> + clk_prepare_enable(keypad->clk);
Too late preparing clock here.
> +
> + return 0;
> +
> +failed_unregister_input:
> + input_unregister_device(input_dev);
> +failed_free_input:
> + input_free_device(input_dev);
Do not mix up devm and non-devm resources.
> + return error;
> +}
> +
> +static void ma35d1_keypad_remove(struct platform_device *pdev)
> +{
> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
> +
> + input_unregister_device(keypad->input_dev);
> + clk_disable_unprepare(keypad->clk);
> +}
> +
> +static int ma35d1_keypad_suspend(struct platform_device *pdev,
> + pm_message_t state)
Oof, this is so old style. Use DEFINE_SIMPLE_DEV_PM_OPS().
> +{
> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
> +
> + if (device_may_wakeup(&pdev->dev)) {
> + writel(readl(keypad->mmio_base + KPI_CONF) | WAKEUP, keypad->mmio_base + KPI_CONF);
> + enable_irq_wake(keypad->irq);
Can you mark the interrupt as a wakeup interrupt in probe by calling
dev_pm_set_wake_irq()? Then you do not need to call enable_irq_wake()
here.
> + }
> +
> + return 0;
> +}
> +
> +static int ma35d1_keypad_resume(struct platform_device *pdev)
> +{
> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
> +
> + if (device_may_wakeup(&pdev->dev)) {
> + writel(readl(keypad->mmio_base + KPI_CONF) & ~(WAKEUP),
> + keypad->mmio_base + KPI_CONF);
> + disable_irq_wake(keypad->irq);
> + }
> +
> + return 0;
> +}
> +
> +static const struct of_device_id ma35d1_kpi_of_match[] = {
> + { .compatible = "nuvoton,ma35d1-kpi"},
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ma35d1_kpi_of_match);
> +
> +static struct platform_driver ma35d1_keypad_driver = {
> + .probe = ma35d1_keypad_probe,
> + .remove = ma35d1_keypad_remove,
> + .suspend = ma35d1_keypad_suspend,
> + .resume = ma35d1_keypad_resume,
> + .driver = {
> + .name = "ma35d1-kpi",
> + .of_match_table = of_match_ptr(ma35d1_kpi_of_match),
> + },
> +};
> +module_platform_driver(ma35d1_keypad_driver);
> +
> +MODULE_AUTHOR("Ming-Jen Chen");
> +MODULE_DESCRIPTION("MA35D1 Keypad Driver");
> +MODULE_LICENSE("GPL");
> +
> --
> 2.17.1
>
Thanks.
--
Dmitry
On 2024/10/24 上午 05:20, Dmitry Torokhov wrote:
> Hi,
>
> On Tue, Oct 22, 2024 at 06:31:58AM +0000, mjchen wrote:
>> From: mjchen <mjchen@nuvoton.com>
>>
>> Adds a new keypad driver for the MA35D1 platform.
>> The driver supports key scanning and interrupt handling.
>>
>> Signed-off-by: mjchen <mjchen@nuvoton.com>
>> ---
>> drivers/input/keyboard/Kconfig | 10 +
>> drivers/input/keyboard/Makefile | 1 +
>> drivers/input/keyboard/ma35d1_keypad.c | 312 +++++++++++++++++++++++++
>> 3 files changed, 323 insertions(+)
>> create mode 100644 drivers/input/keyboard/ma35d1_keypad.c
>>
>> diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
>> index 721ab69e84ac..ce9bd5cc13a1 100644
>> --- a/drivers/input/keyboard/Kconfig
>> +++ b/drivers/input/keyboard/Kconfig
>> @@ -797,4 +797,14 @@ config KEYBOARD_CYPRESS_SF
>> To compile this driver as a module, choose M here: the
>> module will be called cypress-sf.
>>
>> +config KEYBOARD_MA35D1
>> + tristate "Nuvoton MA35D1 keypad driver"
>> + depends on ARCH_MA35
>> + select INPUT_MATRIXKMAP
>> + help
>> + Say Y here if you want to use Nuvoton MA35D1 keypad.
>> +
>> + To compile this driver as a module, choose M here: the
>> + module will be called ma35d1-keypad.
>> +
>> endif
>> diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
>> index 1e0721c30709..9b858cdd1b6b 100644
>> --- a/drivers/input/keyboard/Makefile
>> +++ b/drivers/input/keyboard/Makefile
>> @@ -70,3 +70,4 @@ obj-$(CONFIG_KEYBOARD_TEGRA) += tegra-kbc.o
>> obj-$(CONFIG_KEYBOARD_TM2_TOUCHKEY) += tm2-touchkey.o
>> obj-$(CONFIG_KEYBOARD_TWL4030) += twl4030_keypad.o
>> obj-$(CONFIG_KEYBOARD_XTKBD) += xtkbd.o
>> +obj-$(CONFIG_KEYBOARD_MA35D1) += ma35d1_keypad.o
>> diff --git a/drivers/input/keyboard/ma35d1_keypad.c b/drivers/input/keyboard/ma35d1_keypad.c
>> new file mode 100644
>> index 000000000000..20b5b1b91127
>> --- /dev/null
>> +++ b/drivers/input/keyboard/ma35d1_keypad.c
>> @@ -0,0 +1,312 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * MA35D1 keypad driver
>> + * Copyright (C) 2024 Nuvoton Technology Corp.
>> + */
>> +
>> +#include <linux/interrupt.h>
>> +#include <linux/input.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/input/matrix_keypad.h>
>> +#include <linux/clk.h>
>> +#include <linux/of.h>
>> +
>> +/* Keypad Interface Registers */
>> +#define KPI_CONF 0x00
>> +#define KPI_3KCONF 0x04
>> +#define KPI_STATUS 0x08
>> +#define KPI_RSTC 0x0C
>> +#define KPI_KEST 0x10
>> +#define KPI_KPE0 0x18
>> +#define KPI_KPE1 0x1C
>> +#define KPI_KRE0 0x20
>> +#define KPI_KRE1 0x24
>> +#define KPI_PRESCALDIV 0x28
>> +
>> +/* KPI_CONF - Keypad Configuration Register */
>> +#define KROW GENMASK(30, 28) /* Keypad Matrix ROW number */
>> +#define KCOL GENMASK(26, 24) /* Keypad Matrix COL Number */
>> +#define DB_CLKSEL GENMASK(19, 16) /* De-bounce sampling cycle selection */
>> +#define PRESCALE GENMASK(15, 8) /* Row Scan Cycle Pre-scale Value */
>> +#define WAKEUP BIT(5) /* Lower Power Wakeup Enable */
>> +#define INTEN BIT(3) /* Key Interrupt Enable Control */
>> +#define RKINTEN BIT(2) /* Release Key Interrupt Enable */
>> +#define PKINTEN BIT(1) /* Press Key Interrupt Enable Control */
>> +#define ENKP BIT(0) /* Keypad Scan Enable */
>> +
>> +/* KPI_STATUS - Keypad Status Register */
>> +#define PKEY_INT BIT(4) /* Press key interrupt */
>> +#define RKEY_INT BIT(3) /* Release key interrupt */
>> +#define KEY_INT BIT(2) /* Key Interrupt */
>> +#define RST_3KEY BIT(1) /* 3-Keys Reset Flag */
>> +#define PDWAKE BIT(0) /* Power Down Wakeup Flag */
>> +
>> +#define DEFAULT_DEBOUNCE 1
>> +#define DEFAULT_PRE_SCALE 1
>> +#define DEFAULT_PRE_SCALEDIV 32
>> +
>> +struct ma35d1_keypad {
>> + struct clk *clk;
>> + struct input_dev *input_dev;
>> + void __iomem *mmio_base;
>> + int irq;
>> + unsigned int kpi_row;
>> + unsigned int kpi_col;
>> + unsigned int debounce_val;
>> + unsigned int pre_scale;
>> + unsigned int pre_scale_divider;
>> +};
>> +
>> +static void ma35d1_keypad_scan_matrix(struct ma35d1_keypad *keypad, unsigned int status)
>> +{
>> + struct input_dev *input_dev = keypad->input_dev;
>> + unsigned int i, j;
>> + unsigned int row_add = 0;
>> + unsigned int code;
>> + unsigned int key;
>> + unsigned int press_key;
>> + unsigned long KeyEvent[4];
> No camel-casing please.
I will modify to:unsigned long key_event[4];
>
>> + unsigned int row_shift = get_count_order(keypad->kpi_col);
>> + unsigned short *keymap = input_dev->keycode;
>> +
>> + /* Read key event status */
>> + KeyEvent[0] = readl(keypad->mmio_base + KPI_KPE0);
>> + KeyEvent[1] = readl(keypad->mmio_base + KPI_KPE1);
>> + KeyEvent[2] = readl(keypad->mmio_base + KPI_KRE0);
>> + KeyEvent[3] = readl(keypad->mmio_base + KPI_KRE1);
>> +
>> + /* Clear key event status */
>> + writel(KeyEvent[0], (keypad->mmio_base + KPI_KPE0));
>> + writel(KeyEvent[1], (keypad->mmio_base + KPI_KPE1));
>> + writel(KeyEvent[2], (keypad->mmio_base + KPI_KRE0));
>> + writel(KeyEvent[3], (keypad->mmio_base + KPI_KRE1));
>> +
>> + for (j = 0; j < 4; j++) {
>> + if (KeyEvent[j] != 0) {
>> + row_add = (j % 2) ? 4 : 0;
>> + press_key = (j < 2) ? 1 : 0;
> So you have first 64 bits to indicate pressed keys, followed by 64 bits
> of released keys, right?
>
> I wonder if you could declare 2 bitmaps of 64 bits and then used
> for_each_set_bit() for each of them.
I will modify to:
pressed_keys = KeyEvent[0] | KeyEvent[1] << 32;
released_keys = KeyEvent[2] | KeyEvent[3] << 32;
// Process pressed keys
for_each_set_bit(index, &pressed_keys, KEY_EVENT_BITS) {
code = MATRIX_SCAN_CODE(index/8, (i % 8), row_shift);
key = keymap[code];
input_event(input_dev, EV_MSC, MSC_SCAN, code);
input_report_key(input_dev, key, 1);
}
// Process released keys
for_each_set_bit(index, &released_keys, KEY_EVENT_BITS) {
code = MATRIX_SCAN_CODE(index/8, (i % 8), row_shift);
key = keymap[code];
input_event(input_dev, EV_MSC, MSC_SCAN, code);
input_report_key(input_dev, key, 0);
}
>
>> +
>> + for (i = 0; i < 32; i++) {
>> + if (KeyEvent[j] & (1<<i)) {
>> + code = MATRIX_SCAN_CODE(((i/8) + row_add), (i % 8), row_shift);
>> + key = keymap[code];
>> +
>> + input_event(input_dev, EV_MSC, MSC_SCAN, code);
>> + input_report_key(input_dev, key, press_key);
>> + }
>> + }
>> + }
>> + }
>> +
>> + input_sync(input_dev);
>> +}
>> +
>> +static irqreturn_t ma35d1_keypad_interrupt(int irq, void *dev_id)
>> +{
>> + struct ma35d1_keypad *keypad = dev_id;
>> + unsigned int kstatus;
>> +
>> + kstatus = readl(keypad->mmio_base + KPI_STATUS);
>> +
>> + if (kstatus & (PKEY_INT|RKEY_INT)) {
>> + ma35d1_keypad_scan_matrix(keypad, kstatus);
>> + } else {
> Is this really "else"? Can it be that all 3 bits will be set?
There are indeed four interrupt bits on the hardware, one of which is the "Three Keys Reset" interrupt.
However, my driver does not enable the Three Keys Reset functionality,
so this interrupt will not occur in practice.
Therefore, the actual interrupts that will be triggered are only|PKEY_INT, RKEY_INT and PDWAKE. |
>
>> + if (kstatus & PDWAKE)
>> + writel(PDWAKE, (keypad->mmio_base + KPI_STATUS));
>> + }
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static int ma35d1_keypad_open(struct input_dev *dev)
>> +{
>> + struct ma35d1_keypad *keypad = input_get_drvdata(dev);
>> + unsigned int val, config;
>> +
>> + val = RKINTEN | PKINTEN | INTEN | ENKP;
>> + val |= FIELD_PREP(KCOL, (keypad->kpi_col - 1)) | FIELD_PREP(KROW, (keypad->kpi_row - 1));
>> +
>> + if (keypad->debounce_val > 0)
>> + config = FIELD_PREP(PRESCALE, (keypad->pre_scale - 1)) |
>> + FIELD_PREP(DB_CLKSEL, keypad->debounce_val);
>> + else
>> + config = FIELD_PREP(PRESCALE, (keypad->pre_scale - 1));
>> +
>> + val |= config;
>> +
>> + writel(val, keypad->mmio_base + KPI_CONF);
>> + writel((keypad->pre_scale_divider - 1), keypad->mmio_base + KPI_PRESCALDIV);
>> +
>> + return 0;
>> +}
>> +
>> +static void ma35d1_keypad_close(struct input_dev *dev)
>> +{
>> + struct ma35d1_keypad *keypad = input_get_drvdata(dev);
>> +
>> + clk_disable(keypad->clk);
> This is broken. What will happen if you open and close the device twice?
> If you disable the clock in close() you need to enable it in open().
I will modify the code to ensure that the clock is enabled in the open function and disabled in the close function,
allowing for proper handling when the device is opened and closed multiple times.
>> +}
>> +
>> +static int ma35d1_keypad_probe(struct platform_device *pdev)
>> +{
>> + struct ma35d1_keypad *keypad;
>> + struct input_dev *input_dev;
>> + struct resource *res;
>> + int error = 0;
>> +
>> + keypad = devm_kzalloc(&pdev->dev, sizeof(*keypad), GFP_KERNEL);
>> + if (!keypad)
>> + return -ENOMEM;
>> +
>> +
>> + input_dev = input_allocate_device();
> devm_input_allocate_device().
I will modify to: input_dev = devm_input_allocate_device();
>
>> + if (!input_dev) {
>> + dev_err(&pdev->dev, "failed to allocate input device\n");
>> + return -ENOMEM;
>> + }
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + if (!res) {
>> + dev_err(&pdev->dev, "failed to get I/O memory\n");
>> + error = -ENXIO;
>> + goto failed_free_input;
>> + }
>> +
>> + keypad->mmio_base = devm_ioremap_resource(&pdev->dev, res);
>> + if (IS_ERR(keypad->mmio_base)) {
>> + dev_err(&pdev->dev, "failed to remap I/O memory\n");
>> + return PTR_ERR(keypad->mmio_base);
> Leaking input device (but OK if you switch to devm for it).
I switch to devm.
>
>> + }
>> +
>> + keypad->irq = platform_get_irq(pdev, 0);
>> + if (keypad->irq < 0) {
>> + dev_err(&pdev->dev, "failed to get IRQ\n");
>> + return keypad->irq;
>> + }
>> +
>> + keypad->clk = devm_clk_get(&pdev->dev, NULL);
>> + if (IS_ERR(keypad->clk)) {
>> + dev_err(&pdev->dev, "failed to get core clk: %ld\n", PTR_ERR(keypad->clk));
>> + return PTR_ERR(keypad->clk);
>> + }
>> +
>> + error = matrix_keypad_parse_properties(&pdev->dev,
>> + &(keypad->kpi_row),
>> + &(keypad->kpi_col));
> What tab stop are you using?
Sorry, I'll check my editor settings.
>
>> + if (error) {
>> + dev_err(&pdev->dev, "failed to parse kp params\n");
>> + return error;
>> + }
>> +
>> + error = matrix_keypad_build_keymap(NULL, NULL,
>> + keypad->kpi_row,
>> + keypad->kpi_col,
>> + NULL, input_dev);
>> + if (error) {
>> + dev_err(&pdev->dev, "failed to build keymap\n");
>> + return error;
>> + }
>> +
>> + keypad->input_dev = input_dev;
>> + input_dev->name = pdev->name;
>> + input_dev->id.bustype = BUS_HOST;
>> + input_dev->open = ma35d1_keypad_open;
>> + input_dev->close = ma35d1_keypad_close;
>> + input_dev->dev.parent = &pdev->dev;
>> +
>> + if (of_property_read_u32(pdev->dev.of_node, "debounce-period", &(keypad->debounce_val)))
>> + keypad->debounce_val = DEFAULT_DEBOUNCE;
> Please use generic device property API (device_property_read_u32() and
> others).
I will use device_property_read_u32()
>
>> +
>> + if (of_property_read_u32(pdev->dev.of_node, "per-scale", &(keypad->pre_scale)))
>> + keypad->pre_scale = DEFAULT_PRE_SCALE;
>> +
>> + if (of_property_read_u32(pdev->dev.of_node, "per-scalediv", &(keypad->pre_scale_divider)))
>> + keypad->pre_scale_divider = DEFAULT_PRE_SCALEDIV;
>> +
>> + __set_bit(EV_REP, input_dev->evbit);
>> + input_set_drvdata(input_dev, keypad);
>> + input_set_capability(input_dev, EV_MSC, MSC_SCAN);
>> +
>> + error = input_register_device(input_dev);
>> + if (error) {
>> + dev_err(&pdev->dev, "failed to register input device\n");
>> + goto failed_free_input;
>> + }
>> +
>> + error = devm_request_irq(&pdev->dev, keypad->irq,
>> + ma35d1_keypad_interrupt,
>> + IRQF_NO_SUSPEND, pdev->name, keypad);
> Why IRQF_NO_SUSPEND?
I use this flag to ensure that the keypad’s interrupt remains enabled during system suspend,
allowing it to wake up the system when needed.
Without IRQF_NO_SUSPEND, the interrupt would be disabled,
preventing the keypad from functioning as a wake-up source.
>
>> + if (error) {
>> + dev_err(&pdev->dev, "failed to request IRQ\n");
>> + goto failed_unregister_input;
>> + }
>> +
>> + platform_set_drvdata(pdev, keypad);
>> + device_init_wakeup(&pdev->dev, 1);
>> + clk_prepare_enable(keypad->clk);
> Too late preparing clock here.
I will move the|clk_prepare_enable()| function to be called immediately after|devm_clk_get() |
>
>> +
>> + return 0;
>> +
>> +failed_unregister_input:
>> + input_unregister_device(input_dev);
>> +failed_free_input:
>> + input_free_device(input_dev);
> Do not mix up devm and non-devm resources.
I will use devm.
>
>> + return error;
>> +}
>> +
>> +static void ma35d1_keypad_remove(struct platform_device *pdev)
>> +{
>> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
>> +
>> + input_unregister_device(keypad->input_dev);
>> + clk_disable_unprepare(keypad->clk);
>> +}
>> +
>> +static int ma35d1_keypad_suspend(struct platform_device *pdev,
>> + pm_message_t state)
> Oof, this is so old style. Use DEFINE_SIMPLE_DEV_PM_OPS().
I will modify to:
static DEFINE_SIMPLE_DEV_PM_OPS(ma35d1_pm_ops, ma35d1_keypad_suspend, ma35d1_keypad_resume);
static struct platform_driver ma35d1_keypad_driver = {
.probe = ma35d1_keypad_probe,
.remove = ma35d1_keypad_remove,
.driver = {
.name = "ma35d1-kpi",
.pm = pm_sleep_ptr(&ma35d1_pm_ops),
},
};
>
>> +{
>> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
>> +
>> + if (device_may_wakeup(&pdev->dev)) {
>> + writel(readl(keypad->mmio_base + KPI_CONF) | WAKEUP, keypad->mmio_base + KPI_CONF);
>> + enable_irq_wake(keypad->irq);
> Can you mark the interrupt as a wakeup interrupt in probe by calling
> dev_pm_set_wake_irq()? Then you do not need to call enable_irq_wake()
> here.
Okay, I will use|dev_pm_set_wake_irq()| in the probe and remove|enable_irq_wake()|
>
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int ma35d1_keypad_resume(struct platform_device *pdev)
>> +{
>> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
>> +
>> + if (device_may_wakeup(&pdev->dev)) {
>> + writel(readl(keypad->mmio_base + KPI_CONF) & ~(WAKEUP),
>> + keypad->mmio_base + KPI_CONF);
>> + disable_irq_wake(keypad->irq);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id ma35d1_kpi_of_match[] = {
>> + { .compatible = "nuvoton,ma35d1-kpi"},
>> + {},
>> +};
>> +MODULE_DEVICE_TABLE(of, ma35d1_kpi_of_match);
>> +
>> +static struct platform_driver ma35d1_keypad_driver = {
>> + .probe = ma35d1_keypad_probe,
>> + .remove = ma35d1_keypad_remove,
>> + .suspend = ma35d1_keypad_suspend,
>> + .resume = ma35d1_keypad_resume,
>> + .driver = {
>> + .name = "ma35d1-kpi",
>> + .of_match_table = of_match_ptr(ma35d1_kpi_of_match),
>> + },
>> +};
>> +module_platform_driver(ma35d1_keypad_driver);
>> +
>> +MODULE_AUTHOR("Ming-Jen Chen");
>> +MODULE_DESCRIPTION("MA35D1 Keypad Driver");
>> +MODULE_LICENSE("GPL");
>> +
>> --
>> 2.17.1
>>
> Thanks.
>
On Tue, Oct 22, 2024 at 06:31:58AM +0000, mjchen wrote:
> From: mjchen <mjchen@nuvoton.com>
>
> Adds a new keypad driver for the MA35D1 platform.
> The driver supports key scanning and interrupt handling.
>
> Signed-off-by: mjchen <mjchen@nuvoton.com>
> ---
> drivers/input/keyboard/Kconfig | 10 +
> drivers/input/keyboard/Makefile | 1 +
> drivers/input/keyboard/ma35d1_keypad.c | 312 +++++++++++++++++++++++++
> 3 files changed, 323 insertions(+)
> create mode 100644 drivers/input/keyboard/ma35d1_keypad.c
>
> diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
> index 721ab69e84ac..ce9bd5cc13a1 100644
> --- a/drivers/input/keyboard/Kconfig
> +++ b/drivers/input/keyboard/Kconfig
> @@ -797,4 +797,14 @@ config KEYBOARD_CYPRESS_SF
> To compile this driver as a module, choose M here: the
> module will be called cypress-sf.
>
> +config KEYBOARD_MA35D1
> + tristate "Nuvoton MA35D1 keypad driver"
> + depends on ARCH_MA35
|| COMPILE_TEST
> + select INPUT_MATRIXKMAP
> + help
> + Say Y here if you want to use Nuvoton MA35D1 keypad.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called ma35d1-keypad.
> +
> endif
> diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
> index 1e0721c30709..9b858cdd1b6b 100644
> --- a/drivers/input/keyboard/Makefile
> +++ b/drivers/input/keyboard/Makefile
> @@ -70,3 +70,4 @@ obj-$(CONFIG_KEYBOARD_TEGRA) += tegra-kbc.o
> obj-$(CONFIG_KEYBOARD_TM2_TOUCHKEY) += tm2-touchkey.o
> obj-$(CONFIG_KEYBOARD_TWL4030) += twl4030_keypad.o
> obj-$(CONFIG_KEYBOARD_XTKBD) += xtkbd.o
> +obj-$(CONFIG_KEYBOARD_MA35D1) += ma35d1_keypad.o
> diff --git a/drivers/input/keyboard/ma35d1_keypad.c b/drivers/input/keyboard/ma35d1_keypad.c
> new file mode 100644
> index 000000000000..20b5b1b91127
> --- /dev/null
> +++ b/drivers/input/keyboard/ma35d1_keypad.c
> @@ -0,0 +1,312 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * MA35D1 keypad driver
> + * Copyright (C) 2024 Nuvoton Technology Corp.
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/input.h>
> +#include <linux/platform_device.h>
> +#include <linux/input/matrix_keypad.h>
> +#include <linux/clk.h>
> +#include <linux/of.h>
> +
> +/* Keypad Interface Registers */
> +#define KPI_CONF 0x00
> +#define KPI_3KCONF 0x04
> +#define KPI_STATUS 0x08
> +#define KPI_RSTC 0x0C
> +#define KPI_KEST 0x10
> +#define KPI_KPE0 0x18
> +#define KPI_KPE1 0x1C
> +#define KPI_KRE0 0x20
> +#define KPI_KRE1 0x24
> +#define KPI_PRESCALDIV 0x28
> +
> +/* KPI_CONF - Keypad Configuration Register */
> +#define KROW GENMASK(30, 28) /* Keypad Matrix ROW number */
> +#define KCOL GENMASK(26, 24) /* Keypad Matrix COL Number */
> +#define DB_CLKSEL GENMASK(19, 16) /* De-bounce sampling cycle selection */
> +#define PRESCALE GENMASK(15, 8) /* Row Scan Cycle Pre-scale Value */
> +#define WAKEUP BIT(5) /* Lower Power Wakeup Enable */
> +#define INTEN BIT(3) /* Key Interrupt Enable Control */
> +#define RKINTEN BIT(2) /* Release Key Interrupt Enable */
> +#define PKINTEN BIT(1) /* Press Key Interrupt Enable Control */
> +#define ENKP BIT(0) /* Keypad Scan Enable */
> +
> +/* KPI_STATUS - Keypad Status Register */
> +#define PKEY_INT BIT(4) /* Press key interrupt */
> +#define RKEY_INT BIT(3) /* Release key interrupt */
> +#define KEY_INT BIT(2) /* Key Interrupt */
> +#define RST_3KEY BIT(1) /* 3-Keys Reset Flag */
> +#define PDWAKE BIT(0) /* Power Down Wakeup Flag */
> +
> +#define DEFAULT_DEBOUNCE 1
> +#define DEFAULT_PRE_SCALE 1
> +#define DEFAULT_PRE_SCALEDIV 32
> +
> +struct ma35d1_keypad {
> + struct clk *clk;
> + struct input_dev *input_dev;
> + void __iomem *mmio_base;
> + int irq;
> + unsigned int kpi_row;
> + unsigned int kpi_col;
> + unsigned int debounce_val;
> + unsigned int pre_scale;
> + unsigned int pre_scale_divider;
> +};
> +
> +static void ma35d1_keypad_scan_matrix(struct ma35d1_keypad *keypad, unsigned int status)
> +{
> + struct input_dev *input_dev = keypad->input_dev;
> + unsigned int i, j;
> + unsigned int row_add = 0;
> + unsigned int code;
> + unsigned int key;
> + unsigned int press_key;
> + unsigned long KeyEvent[4];
No Windows or C++ code, please.
> + unsigned int row_shift = get_count_order(keypad->kpi_col);
> + unsigned short *keymap = input_dev->keycode;
> +
...
> +static int ma35d1_keypad_probe(struct platform_device *pdev)
> +{
> + struct ma35d1_keypad *keypad;
> + struct input_dev *input_dev;
> + struct resource *res;
> + int error = 0;
> +
> + keypad = devm_kzalloc(&pdev->dev, sizeof(*keypad), GFP_KERNEL);
> + if (!keypad)
> + return -ENOMEM;
> +
> +
> + input_dev = input_allocate_device();
> + if (!input_dev) {
> + dev_err(&pdev->dev, "failed to allocate input device\n");
> + return -ENOMEM;
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res) {
> + dev_err(&pdev->dev, "failed to get I/O memory\n");
> + error = -ENXIO;
> + goto failed_free_input;
> + }
> +
> + keypad->mmio_base = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(keypad->mmio_base)) {
> + dev_err(&pdev->dev, "failed to remap I/O memory\n");
> + return PTR_ERR(keypad->mmio_base);
> + }
> +
> + keypad->irq = platform_get_irq(pdev, 0);
> + if (keypad->irq < 0) {
> + dev_err(&pdev->dev, "failed to get IRQ\n");
> + return keypad->irq;
> + }
> +
> + keypad->clk = devm_clk_get(&pdev->dev, NULL);
> + if (IS_ERR(keypad->clk)) {
> + dev_err(&pdev->dev, "failed to get core clk: %ld\n", PTR_ERR(keypad->clk));
Syntax is: return dev_err_probe, except that your error handling code is a mess.
Earlier you have gotos, now return. Organize it nicely, so this will
follow some logical concept.
> + return PTR_ERR(keypad->clk);
> + }
> +
> + error = matrix_keypad_parse_properties(&pdev->dev,
> + &(keypad->kpi_row),
> + &(keypad->kpi_col));
How did you aligned it?
> + if (error) {
> + dev_err(&pdev->dev, "failed to parse kp params\n");
> + return error;
> + }
> +
> + error = matrix_keypad_build_keymap(NULL, NULL,
> + keypad->kpi_row,
> + keypad->kpi_col,
> + NULL, input_dev);
> + if (error) {
> + dev_err(&pdev->dev, "failed to build keymap\n");
> + return error;
> + }
> +
> + keypad->input_dev = input_dev;
> + input_dev->name = pdev->name;
> + input_dev->id.bustype = BUS_HOST;
> + input_dev->open = ma35d1_keypad_open;
> + input_dev->close = ma35d1_keypad_close;
> + input_dev->dev.parent = &pdev->dev;
> +
> + if (of_property_read_u32(pdev->dev.of_node, "debounce-period", &(keypad->debounce_val)))
> + keypad->debounce_val = DEFAULT_DEBOUNCE;
This is not used anywhere. Drop dead code.
> +
> + if (of_property_read_u32(pdev->dev.of_node, "per-scale", &(keypad->pre_scale)))
> + keypad->pre_scale = DEFAULT_PRE_SCALE;
Not better...
> +
> + if (of_property_read_u32(pdev->dev.of_node, "per-scalediv", &(keypad->pre_scale_divider)))
> + keypad->pre_scale_divider = DEFAULT_PRE_SCALEDIV;
Still not better...
So there are defaults? Why these are required by bindings? Why bindings do not say
defaults?
> +
> + __set_bit(EV_REP, input_dev->evbit);
> + input_set_drvdata(input_dev, keypad);
> + input_set_capability(input_dev, EV_MSC, MSC_SCAN);
> +
> + error = input_register_device(input_dev);
> + if (error) {
> + dev_err(&pdev->dev, "failed to register input device\n");
> + goto failed_free_input;
> + }
> +
> + error = devm_request_irq(&pdev->dev, keypad->irq,
> + ma35d1_keypad_interrupt,
> + IRQF_NO_SUSPEND, pdev->name, keypad);
Totally mesed alignment.
> + if (error) {
> + dev_err(&pdev->dev, "failed to request IRQ\n");
> + goto failed_unregister_input;
> + }
> +
> + platform_set_drvdata(pdev, keypad);
> + device_init_wakeup(&pdev->dev, 1);
> + clk_prepare_enable(keypad->clk);
> +
> + return 0;
> +
> +failed_unregister_input:
> + input_unregister_device(input_dev);
> +failed_free_input:
> + input_free_device(input_dev);
> + return error;
> +}
> +
> +static void ma35d1_keypad_remove(struct platform_device *pdev)
> +{
> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
> +
> + input_unregister_device(keypad->input_dev);
> + clk_disable_unprepare(keypad->clk);
Why aren't you using devm_clk_get_enabled()?
> +}
> +
> +static int ma35d1_keypad_suspend(struct platform_device *pdev,
> + pm_message_t state)
> +{
> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
> +
> + if (device_may_wakeup(&pdev->dev)) {
> + writel(readl(keypad->mmio_base + KPI_CONF) | WAKEUP, keypad->mmio_base + KPI_CONF);
> + enable_irq_wake(keypad->irq);
> + }
> +
> + return 0;
> +}
> +
> +static int ma35d1_keypad_resume(struct platform_device *pdev)
> +{
> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
> +
> + if (device_may_wakeup(&pdev->dev)) {
> + writel(readl(keypad->mmio_base + KPI_CONF) & ~(WAKEUP),
> + keypad->mmio_base + KPI_CONF);
> + disable_irq_wake(keypad->irq);
> + }
> +
> + return 0;
> +}
> +
> +static const struct of_device_id ma35d1_kpi_of_match[] = {
> + { .compatible = "nuvoton,ma35d1-kpi"},
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ma35d1_kpi_of_match);
> +
> +static struct platform_driver ma35d1_keypad_driver = {
> + .probe = ma35d1_keypad_probe,
> + .remove = ma35d1_keypad_remove,
> + .suspend = ma35d1_keypad_suspend,
> + .resume = ma35d1_keypad_resume,
> + .driver = {
> + .name = "ma35d1-kpi",
> + .of_match_table = of_match_ptr(ma35d1_kpi_of_match),
Drop of_match_ptr(), you have warnings here.
Best regards,
Krzysztof
On 2024/10/23 下午 04:45, Krzysztof Kozlowski wrote:
> On Tue, Oct 22, 2024 at 06:31:58AM +0000, mjchen wrote:
>> From: mjchen <mjchen@nuvoton.com>
>>
>> Adds a new keypad driver for the MA35D1 platform.
>> The driver supports key scanning and interrupt handling.
>>
>> Signed-off-by: mjchen <mjchen@nuvoton.com>
>> ---
>> drivers/input/keyboard/Kconfig | 10 +
>> drivers/input/keyboard/Makefile | 1 +
>> drivers/input/keyboard/ma35d1_keypad.c | 312 +++++++++++++++++++++++++
>> 3 files changed, 323 insertions(+)
>> create mode 100644 drivers/input/keyboard/ma35d1_keypad.c
>>
>> diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
>> index 721ab69e84ac..ce9bd5cc13a1 100644
>> --- a/drivers/input/keyboard/Kconfig
>> +++ b/drivers/input/keyboard/Kconfig
>> @@ -797,4 +797,14 @@ config KEYBOARD_CYPRESS_SF
>> To compile this driver as a module, choose M here: the
>> module will be called cypress-sf.
>>
>> +config KEYBOARD_MA35D1
>> + tristate "Nuvoton MA35D1 keypad driver"
>> + depends on ARCH_MA35
> || COMPILE_TEST
I will modify to: depends on ARCH_MA35 || COMPILE_TEST
>
>> + select INPUT_MATRIXKMAP
>> + help
>> + Say Y here if you want to use Nuvoton MA35D1 keypad.
>> +
>> + To compile this driver as a module, choose M here: the
>> + module will be called ma35d1-keypad.
>> +
>> endif
>> diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
>> index 1e0721c30709..9b858cdd1b6b 100644
>> --- a/drivers/input/keyboard/Makefile
>> +++ b/drivers/input/keyboard/Makefile
>> @@ -70,3 +70,4 @@ obj-$(CONFIG_KEYBOARD_TEGRA) += tegra-kbc.o
>> obj-$(CONFIG_KEYBOARD_TM2_TOUCHKEY) += tm2-touchkey.o
>> obj-$(CONFIG_KEYBOARD_TWL4030) += twl4030_keypad.o
>> obj-$(CONFIG_KEYBOARD_XTKBD) += xtkbd.o
>> +obj-$(CONFIG_KEYBOARD_MA35D1) += ma35d1_keypad.o
>> diff --git a/drivers/input/keyboard/ma35d1_keypad.c b/drivers/input/keyboard/ma35d1_keypad.c
>> new file mode 100644
>> index 000000000000..20b5b1b91127
>> --- /dev/null
>> +++ b/drivers/input/keyboard/ma35d1_keypad.c
>> @@ -0,0 +1,312 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * MA35D1 keypad driver
>> + * Copyright (C) 2024 Nuvoton Technology Corp.
>> + */
>> +
>> +#include <linux/interrupt.h>
>> +#include <linux/input.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/input/matrix_keypad.h>
>> +#include <linux/clk.h>
>> +#include <linux/of.h>
>> +
>> +/* Keypad Interface Registers */
>> +#define KPI_CONF 0x00
>> +#define KPI_3KCONF 0x04
>> +#define KPI_STATUS 0x08
>> +#define KPI_RSTC 0x0C
>> +#define KPI_KEST 0x10
>> +#define KPI_KPE0 0x18
>> +#define KPI_KPE1 0x1C
>> +#define KPI_KRE0 0x20
>> +#define KPI_KRE1 0x24
>> +#define KPI_PRESCALDIV 0x28
>> +
>> +/* KPI_CONF - Keypad Configuration Register */
>> +#define KROW GENMASK(30, 28) /* Keypad Matrix ROW number */
>> +#define KCOL GENMASK(26, 24) /* Keypad Matrix COL Number */
>> +#define DB_CLKSEL GENMASK(19, 16) /* De-bounce sampling cycle selection */
>> +#define PRESCALE GENMASK(15, 8) /* Row Scan Cycle Pre-scale Value */
>> +#define WAKEUP BIT(5) /* Lower Power Wakeup Enable */
>> +#define INTEN BIT(3) /* Key Interrupt Enable Control */
>> +#define RKINTEN BIT(2) /* Release Key Interrupt Enable */
>> +#define PKINTEN BIT(1) /* Press Key Interrupt Enable Control */
>> +#define ENKP BIT(0) /* Keypad Scan Enable */
>> +
>> +/* KPI_STATUS - Keypad Status Register */
>> +#define PKEY_INT BIT(4) /* Press key interrupt */
>> +#define RKEY_INT BIT(3) /* Release key interrupt */
>> +#define KEY_INT BIT(2) /* Key Interrupt */
>> +#define RST_3KEY BIT(1) /* 3-Keys Reset Flag */
>> +#define PDWAKE BIT(0) /* Power Down Wakeup Flag */
>> +
>> +#define DEFAULT_DEBOUNCE 1
>> +#define DEFAULT_PRE_SCALE 1
>> +#define DEFAULT_PRE_SCALEDIV 32
>> +
>> +struct ma35d1_keypad {
>> + struct clk *clk;
>> + struct input_dev *input_dev;
>> + void __iomem *mmio_base;
>> + int irq;
>> + unsigned int kpi_row;
>> + unsigned int kpi_col;
>> + unsigned int debounce_val;
>> + unsigned int pre_scale;
>> + unsigned int pre_scale_divider;
>> +};
>> +
>> +static void ma35d1_keypad_scan_matrix(struct ma35d1_keypad *keypad, unsigned int status)
>> +{
>> + struct input_dev *input_dev = keypad->input_dev;
>> + unsigned int i, j;
>> + unsigned int row_add = 0;
>> + unsigned int code;
>> + unsigned int key;
>> + unsigned int press_key;
>> + unsigned long KeyEvent[4];
> No Windows or C++ code, please.
I will modify to:unsigned long key_event[4];
>
>> + unsigned int row_shift = get_count_order(keypad->kpi_col);
>> + unsigned short *keymap = input_dev->keycode;
>> +
> ...
>
>> +static int ma35d1_keypad_probe(struct platform_device *pdev)
>> +{
>> + struct ma35d1_keypad *keypad;
>> + struct input_dev *input_dev;
>> + struct resource *res;
>> + int error = 0;
>> +
>> + keypad = devm_kzalloc(&pdev->dev, sizeof(*keypad), GFP_KERNEL);
>> + if (!keypad)
>> + return -ENOMEM;
>> +
>> +
>> + input_dev = input_allocate_device();
>> + if (!input_dev) {
>> + dev_err(&pdev->dev, "failed to allocate input device\n");
>> + return -ENOMEM;
>> + }
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + if (!res) {
>> + dev_err(&pdev->dev, "failed to get I/O memory\n");
>> + error = -ENXIO;
>> + goto failed_free_input;
>> + }
>> +
>> + keypad->mmio_base = devm_ioremap_resource(&pdev->dev, res);
>> + if (IS_ERR(keypad->mmio_base)) {
>> + dev_err(&pdev->dev, "failed to remap I/O memory\n");
>> + return PTR_ERR(keypad->mmio_base);
>> + }
>> +
>> + keypad->irq = platform_get_irq(pdev, 0);
>> + if (keypad->irq < 0) {
>> + dev_err(&pdev->dev, "failed to get IRQ\n");
>> + return keypad->irq;
>> + }
>> +
>> + keypad->clk = devm_clk_get(&pdev->dev, NULL);
>> + if (IS_ERR(keypad->clk)) {
>> + dev_err(&pdev->dev, "failed to get core clk: %ld\n", PTR_ERR(keypad->clk));
> Syntax is: return dev_err_probe, except that your error handling code is a mess.
> Earlier you have gotos, now return. Organize it nicely, so this will
> follow some logical concept.
I will refactor the error handling in my driver to consistently use either the return dev_err_probe() statement
or the goto method, ensuring a clearer and more logical flow in the code.
>
>> + return PTR_ERR(keypad->clk);
>> + }
>> +
>> + error = matrix_keypad_parse_properties(&pdev->dev,
>> + &(keypad->kpi_row),
>> + &(keypad->kpi_col));
> How did you aligned it?
>
>> + if (error) {
>> + dev_err(&pdev->dev, "failed to parse kp params\n");
>> + return error;
>> + }
>> +
>> + error = matrix_keypad_build_keymap(NULL, NULL,
>> + keypad->kpi_row,
>> + keypad->kpi_col,
>> + NULL, input_dev);
>> + if (error) {
>> + dev_err(&pdev->dev, "failed to build keymap\n");
>> + return error;
>> + }
>> +
>> + keypad->input_dev = input_dev;
>> + input_dev->name = pdev->name;
>> + input_dev->id.bustype = BUS_HOST;
>> + input_dev->open = ma35d1_keypad_open;
>> + input_dev->close = ma35d1_keypad_close;
>> + input_dev->dev.parent = &pdev->dev;
>> +
>> + if (of_property_read_u32(pdev->dev.of_node, "debounce-period", &(keypad->debounce_val)))
>> + keypad->debounce_val = DEFAULT_DEBOUNCE;
> This is not used anywhere. Drop dead code.
In|ma35d1_keypad_open()|, I used|keypad->debounce_val| to set the debounce length.
>
>> +
>> + if (of_property_read_u32(pdev->dev.of_node, "per-scale", &(keypad->pre_scale)))
>> + keypad->pre_scale = DEFAULT_PRE_SCALE;
> Not better...
>
>> +
>> + if (of_property_read_u32(pdev->dev.of_node, "per-scalediv", &(keypad->pre_scale_divider)))
>> + keypad->pre_scale_divider = DEFAULT_PRE_SCALEDIV;
> Still not better...
>
> So there are defaults? Why these are required by bindings? Why bindings do not say
> defaults?
I will remove the default values for pre-scale and pre-scalediv.
>
>> +
>> + __set_bit(EV_REP, input_dev->evbit);
>> + input_set_drvdata(input_dev, keypad);
>> + input_set_capability(input_dev, EV_MSC, MSC_SCAN);
>> +
>> + error = input_register_device(input_dev);
>> + if (error) {
>> + dev_err(&pdev->dev, "failed to register input device\n");
>> + goto failed_free_input;
>> + }
>> +
>> + error = devm_request_irq(&pdev->dev, keypad->irq,
>> + ma35d1_keypad_interrupt,
>> + IRQF_NO_SUSPEND, pdev->name, keypad);
> Totally mesed alignment.
I will review the editor settings and make the necessary adjustments to resolve this problem.
>
>> + if (error) {
>> + dev_err(&pdev->dev, "failed to request IRQ\n");
>> + goto failed_unregister_input;
>> + }
>> +
>> + platform_set_drvdata(pdev, keypad);
>> + device_init_wakeup(&pdev->dev, 1);
>> + clk_prepare_enable(keypad->clk);
>> +
>> + return 0;
>> +
>> +failed_unregister_input:
>> + input_unregister_device(input_dev);
>> +failed_free_input:
>> + input_free_device(input_dev);
>> + return error;
>> +}
>> +
>> +static void ma35d1_keypad_remove(struct platform_device *pdev)
>> +{
>> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
>> +
>> + input_unregister_device(keypad->input_dev);
>> + clk_disable_unprepare(keypad->clk);
> Why aren't you using devm_clk_get_enabled()?
I will update the code to utilize devm_clk_get_enabled() and remove the clk_disable_unprepare(keypad->clk)
>
>> +}
>> +
>> +static int ma35d1_keypad_suspend(struct platform_device *pdev,
>> + pm_message_t state)
>> +{
>> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
>> +
>> + if (device_may_wakeup(&pdev->dev)) {
>> + writel(readl(keypad->mmio_base + KPI_CONF) | WAKEUP, keypad->mmio_base + KPI_CONF);
>> + enable_irq_wake(keypad->irq);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int ma35d1_keypad_resume(struct platform_device *pdev)
>> +{
>> + struct ma35d1_keypad *keypad = platform_get_drvdata(pdev);
>> +
>> + if (device_may_wakeup(&pdev->dev)) {
>> + writel(readl(keypad->mmio_base + KPI_CONF) & ~(WAKEUP),
>> + keypad->mmio_base + KPI_CONF);
>> + disable_irq_wake(keypad->irq);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id ma35d1_kpi_of_match[] = {
>> + { .compatible = "nuvoton,ma35d1-kpi"},
>> + {},
>> +};
>> +MODULE_DEVICE_TABLE(of, ma35d1_kpi_of_match);
>> +
>> +static struct platform_driver ma35d1_keypad_driver = {
>> + .probe = ma35d1_keypad_probe,
>> + .remove = ma35d1_keypad_remove,
>> + .suspend = ma35d1_keypad_suspend,
>> + .resume = ma35d1_keypad_resume,
>> + .driver = {
>> + .name = "ma35d1-kpi",
>> + .of_match_table = of_match_ptr(ma35d1_kpi_of_match),
> Drop of_match_ptr(), you have warnings here.
I will remove this line of code.
>
> Best regards,
> Krzysztof
Best regards,
Ming-Jen Chen
© 2016 - 2024 Red Hat, Inc.