Convert the AXI DMAC bindings from .txt to .yaml.

Signed-off-by: David Lechner <dlechner@baylibre.com>
---

For the maintainer, Lars is the original author, but isn't really
active with ADI anymore, so I have added Nuno instead since he is the
most active ADI representative currently and is knowledgeable about this
hardware.

Also, the rob-bot is likely to complain. Locally, I am getting the
following warning from dt_bindings_check:

	Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml: properties:adi,channels:type: 'boolean' was expected
		hint: A vendor boolean property can use "type: boolean"
		from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#
	DTC [C] Documentation/devicetree/bindings/dma/adi,axi-dmac.example.dtb

I think this is telling me that object nodes should not have a vendor
prefix. However, since this is an existing bindings, we can't change
that.
---
 .../devicetree/bindings/dma/adi,axi-dmac.txt       |  61 ---------
 .../devicetree/bindings/dma/adi,axi-dmac.yaml      | 137 +++++++++++++++++++++
 2 files changed, 137 insertions(+), 61 deletions(-)

diff --git a/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
deleted file mode 100644
index cd17684aaab5..000000000000
--- a/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
+++ /dev/null
@@ -1,61 +0,0 @@
-Analog Devices AXI-DMAC DMA controller
-
-Required properties:
- - compatible: Must be "adi,axi-dmac-1.00.a".
- - reg: Specification for the controllers memory mapped register map.
- - interrupts: Specification for the controllers interrupt.
- - clocks: Phandle and specifier to the controllers AXI interface clock
- - #dma-cells: Must be 1.
-
-Required sub-nodes:
- - adi,channels: This sub-node must contain a sub-node for each DMA channel. For
-   the channel sub-nodes the following bindings apply. They must match the
-   configuration options of the peripheral as it was instantiated.
-
-Required properties for adi,channels sub-node:
- - #size-cells: Must be 0
- - #address-cells: Must be 1
-
-Required channel sub-node properties:
- - reg: Which channel this node refers to.
- - adi,source-bus-width,
-   adi,destination-bus-width: Width of the source or destination bus in bits.
- - adi,source-bus-type,
-   adi,destination-bus-type: Type of the source or destination bus. Must be one
-   of the following:
-	0 (AXI_DMAC_TYPE_AXI_MM): Memory mapped AXI interface
-	1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface
-	2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface
-
-Deprecated optional channel properties:
- - adi,length-width: Width of the DMA transfer length register.
- - adi,cyclic: Must be set if the channel supports hardware cyclic DMA
-   transfers.
- - adi,2d: Must be set if the channel supports hardware 2D DMA transfers.
-
-DMA clients connected to the AXI-DMAC DMA controller must use the format
-described in the dma.txt file using a one-cell specifier. The value of the
-specifier refers to the DMA channel index.
-
-Example:
-
-dma: dma@7c420000 {
-	compatible = "adi,axi-dmac-1.00.a";
-	reg = <0x7c420000 0x10000>;
-	interrupts = <0 57 0>;
-	clocks = <&clkc 16>;
-	#dma-cells = <1>;
-
-	adi,channels {
-		#size-cells = <0>;
-		#address-cells = <1>;
-
-		dma-channel@0 {
-			reg = <0>;
-			adi,source-bus-width = <32>;
-			adi,source-bus-type = <ADI_AXI_DMAC_TYPE_MM_AXI>;
-			adi,destination-bus-width = <64>;
-			adi,destination-bus-type = <ADI_AXI_DMAC_TYPE_FIFO>;
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml b/Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml
new file mode 100644
index 000000000000..e457630ec7c0
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml
@@ -0,0 +1,137 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/adi,axi-dmac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices AXI-DMAC DMA controller
+
+description: http://analogdevicesinc.github.io/hdl/library/axi_dmac/index.html
+
+maintainers:
+  - Nuno Sa <nuno.sa@analog.com>
+
+properties:
+  compatible:
+    const: adi,axi-dmac-1.00.a
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  "#dma-cells":
+    const: 1
+
+  adi,channels:
+    type: object
+    description: This sub-node must contain a sub-node for each DMA channel.
+
+    properties:
+      "#size-cells":
+        const: 0
+      "#address-cells":
+        const: 1
+
+    patternProperties:
+      "^dma-channel@[0-9a-f]+$":
+        type: object
+        description:
+          DMA channel properties based on HDL compile-time configuration.
+
+        properties:
+          reg:
+            maxItems: 1
+
+          adi,source-bus-width:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: Width of the source bus in bits.
+            enum: [8, 16, 32, 64, 128]
+
+          adi,destination-bus-width:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: Width of the destination bus in bits.
+            enum: [8, 16, 32, 64, 128]
+
+          # 0 (AXI_DMAC_TYPE_AXI_MM): Memory mapped AXI interface
+          # 1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface
+          # 2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface
+
+          adi,source-bus-type:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: Type of the source bus.
+            enum: [0, 1, 2]
+
+          adi,destination-bus-type:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: Type of the destination bus.
+            enum: [0, 1, 2]
+
+          adi,length-width:
+            deprecated: true
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: Width of the DMA transfer length register.
+
+          adi,cyclic:
+            deprecated: true
+            type: boolean
+            description:
+              Must be set if the channel supports hardware cyclic DMA transfers.
+
+          adi,2d:
+            deprecated: true
+            type: boolean
+            description:
+              Must be set if the channel supports hardware 2D DMA transfers.
+
+        required:
+          - reg
+          - adi,source-bus-width
+          - adi,destination-bus-width
+          - adi,source-bus-type
+          - adi,destination-bus-type
+
+        additionalProperties: false
+
+    required:
+      - "#size-cells"
+      - "#address-cells"
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - "#dma-cells"
+  - adi,channels
+
+additionalProperties: false
+
+examples:
+  - |
+    dma: dma@7c420000 {
+        compatible = "adi,axi-dmac-1.00.a";
+        reg = <0x7c420000 0x10000>;
+        interrupts = <0 57 0>;
+        clocks = <&clkc 16>;
+        #dma-cells = <1>;
+
+        adi,channels {
+            #size-cells = <0>;
+            #address-cells = <1>;
+
+            dma-channel@0 {
+                reg = <0>;
+                adi,source-bus-width = <32>;
+                adi,source-bus-type = <0>; /* AXI_DMAC_TYPE_AXI_MM */
+                adi,destination-bus-width = <64>;
+                adi,destination-bus-type = <2>; /* AXI_DMAC_TYPE_AXI_FIFO */
+            };
+        };
+    };

-- 
2.43.0

On Tue, Oct 22, 2024 at 12:46:40PM -0500, David Lechner wrote:
> Convert the AXI DMAC bindings from .txt to .yaml.
> 
> Signed-off-by: David Lechner <dlechner@baylibre.com>
> ---
> 
> For the maintainer, Lars is the original author, but isn't really
> active with ADI anymore, so I have added Nuno instead since he is the
> most active ADI representative currently and is knowledgeable about this
> hardware.
> 
> Also, the rob-bot is likely to complain. Locally, I am getting the
> following warning from dt_bindings_check:
> 
> 	Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml: properties:adi,channels:type: 'boolean' was expected
> 		hint: A vendor boolean property can use "type: boolean"
> 		from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#
> 	DTC [C] Documentation/devicetree/bindings/dma/adi,axi-dmac.example.dtb
> 
> I think this is telling me that object nodes should not have a vendor
> prefix. However, since this is an existing bindings, we can't change
> that.

Yes, that can be ignored. I'll have to drop that check from dtschema.

> ---
>  .../devicetree/bindings/dma/adi,axi-dmac.txt       |  61 ---------
>  .../devicetree/bindings/dma/adi,axi-dmac.yaml      | 137 +++++++++++++++++++++
>  2 files changed, 137 insertions(+), 61 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
> deleted file mode 100644
> index cd17684aaab5..000000000000
> --- a/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt
> +++ /dev/null
> @@ -1,61 +0,0 @@
> -Analog Devices AXI-DMAC DMA controller
> -
> -Required properties:
> - - compatible: Must be "adi,axi-dmac-1.00.a".
> - - reg: Specification for the controllers memory mapped register map.
> - - interrupts: Specification for the controllers interrupt.
> - - clocks: Phandle and specifier to the controllers AXI interface clock
> - - #dma-cells: Must be 1.
> -
> -Required sub-nodes:
> - - adi,channels: This sub-node must contain a sub-node for each DMA channel. For
> -   the channel sub-nodes the following bindings apply. They must match the
> -   configuration options of the peripheral as it was instantiated.
> -
> -Required properties for adi,channels sub-node:
> - - #size-cells: Must be 0
> - - #address-cells: Must be 1
> -
> -Required channel sub-node properties:
> - - reg: Which channel this node refers to.
> - - adi,source-bus-width,
> -   adi,destination-bus-width: Width of the source or destination bus in bits.
> - - adi,source-bus-type,
> -   adi,destination-bus-type: Type of the source or destination bus. Must be one
> -   of the following:
> -	0 (AXI_DMAC_TYPE_AXI_MM): Memory mapped AXI interface
> -	1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface
> -	2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface
> -
> -Deprecated optional channel properties:
> - - adi,length-width: Width of the DMA transfer length register.
> - - adi,cyclic: Must be set if the channel supports hardware cyclic DMA
> -   transfers.
> - - adi,2d: Must be set if the channel supports hardware 2D DMA transfers.
> -
> -DMA clients connected to the AXI-DMAC DMA controller must use the format
> -described in the dma.txt file using a one-cell specifier. The value of the
> -specifier refers to the DMA channel index.
> -
> -Example:
> -
> -dma: dma@7c420000 {
> -	compatible = "adi,axi-dmac-1.00.a";
> -	reg = <0x7c420000 0x10000>;
> -	interrupts = <0 57 0>;
> -	clocks = <&clkc 16>;
> -	#dma-cells = <1>;
> -
> -	adi,channels {
> -		#size-cells = <0>;
> -		#address-cells = <1>;
> -
> -		dma-channel@0 {
> -			reg = <0>;
> -			adi,source-bus-width = <32>;
> -			adi,source-bus-type = <ADI_AXI_DMAC_TYPE_MM_AXI>;
> -			adi,destination-bus-width = <64>;
> -			adi,destination-bus-type = <ADI_AXI_DMAC_TYPE_FIFO>;
> -		};
> -	};
> -};
> diff --git a/Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml b/Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml
> new file mode 100644
> index 000000000000..e457630ec7c0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml
> @@ -0,0 +1,137 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/dma/adi,axi-dmac.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices AXI-DMAC DMA controller
> +
> +description: http://analogdevicesinc.github.io/hdl/library/axi_dmac/index.html

Please make description more than just a link.

> +
> +maintainers:
> +  - Nuno Sa <nuno.sa@analog.com>
> +
> +properties:
> +  compatible:
> +    const: adi,axi-dmac-1.00.a
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  "#dma-cells":
> +    const: 1
> +
> +  adi,channels:
> +    type: object
> +    description: This sub-node must contain a sub-node for each DMA channel.
> +
> +    properties:
> +      "#size-cells":
> +        const: 0
> +      "#address-cells":
> +        const: 1
> +
> +    patternProperties:
> +      "^dma-channel@[0-9a-f]+$":
> +        type: object
> +        description:
> +          DMA channel properties based on HDL compile-time configuration.
> +
> +        properties:
> +          reg:
> +            maxItems: 1
> +
> +          adi,source-bus-width:
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            description: Width of the source bus in bits.
> +            enum: [8, 16, 32, 64, 128]
> +
> +          adi,destination-bus-width:
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            description: Width of the destination bus in bits.
> +            enum: [8, 16, 32, 64, 128]
> +
> +          # 0 (AXI_DMAC_TYPE_AXI_MM): Memory mapped AXI interface
> +          # 1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface
> +          # 2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface

Put these in the 'description'

> +
> +          adi,source-bus-type:
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            description: Type of the source bus.
> +            enum: [0, 1, 2]
> +
> +          adi,destination-bus-type:
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            description: Type of the destination bus.
> +            enum: [0, 1, 2]
> +
> +          adi,length-width:
> +            deprecated: true
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            description: Width of the DMA transfer length register.
> +
> +          adi,cyclic:
> +            deprecated: true
> +            type: boolean
> +            description:
> +              Must be set if the channel supports hardware cyclic DMA transfers.
> +
> +          adi,2d:
> +            deprecated: true
> +            type: boolean
> +            description:
> +              Must be set if the channel supports hardware 2D DMA transfers.
> +
> +        required:
> +          - reg
> +          - adi,source-bus-width
> +          - adi,destination-bus-width
> +          - adi,source-bus-type
> +          - adi,destination-bus-type
> +
> +        additionalProperties: false

Put this before 'properties'. Easier to read the indented cases that 
way.

> +
> +    required:
> +      - "#size-cells"
> +      - "#address-cells"
> +
> +    additionalProperties: false

ditto

> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - "#dma-cells"
> +  - adi,channels
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    dma: dma@7c420000 {

Drop unused labels.

dma-controller@7c420000

> +        compatible = "adi,axi-dmac-1.00.a";
> +        reg = <0x7c420000 0x10000>;
> +        interrupts = <0 57 0>;
> +        clocks = <&clkc 16>;
> +        #dma-cells = <1>;
> +
> +        adi,channels {
> +            #size-cells = <0>;
> +            #address-cells = <1>;
> +
> +            dma-channel@0 {
> +                reg = <0>;
> +                adi,source-bus-width = <32>;
> +                adi,source-bus-type = <0>; /* AXI_DMAC_TYPE_AXI_MM */
> +                adi,destination-bus-width = <64>;
> +                adi,destination-bus-type = <2>; /* AXI_DMAC_TYPE_AXI_FIFO */
> +            };
> +        };
> +    };
> 
> -- 
> 2.43.0
>

On Tue, 22 Oct 2024 12:46:40 -0500, David Lechner wrote:
> Convert the AXI DMAC bindings from .txt to .yaml.
> 
> Signed-off-by: David Lechner <dlechner@baylibre.com>
> ---
> 
> For the maintainer, Lars is the original author, but isn't really
> active with ADI anymore, so I have added Nuno instead since he is the
> most active ADI representative currently and is knowledgeable about this
> hardware.
> 
> Also, the rob-bot is likely to complain. Locally, I am getting the
> following warning from dt_bindings_check:
> 
> 	Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml: properties:adi,channels:type: 'boolean' was expected
> 		hint: A vendor boolean property can use "type: boolean"
> 		from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#
> 	DTC [C] Documentation/devicetree/bindings/dma/adi,axi-dmac.example.dtb
> 
> I think this is telling me that object nodes should not have a vendor
> prefix. However, since this is an existing bindings, we can't change
> that.
> ---
>  .../devicetree/bindings/dma/adi,axi-dmac.txt       |  61 ---------
>  .../devicetree/bindings/dma/adi,axi-dmac.yaml      | 137 +++++++++++++++++++++
>  2 files changed, 137 insertions(+), 61 deletions(-)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/dma/adi,axi-dmac.yaml: properties:adi,channels:type: 'boolean' was expected
	hint: A vendor boolean property can use "type: boolean"
	from schema $id: http://devicetree.org/meta-schemas/vendor-props.yaml#

doc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20241022-axi-dma-dt-yaml-v1-1-68f2a2498d53@baylibre.com

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.