Hello all,
This series provides some crucial fixes and improvements for the Cadence's DSI
TX (cdns-dsi) controller found commonly in Texas Instruments' J7 family of SoCs
as well as in AM62P.
Along with that, this series aims to fix the color-shift issue that has been
going on with the DSI controller. This controller requires to be enabled before
the previous entity enables its stream[0]. It's a strict requirement which, if
not followed, causes the colors to "shift" on the display. The fix happens in
2 steps.
1. The bridge pre_enable calls have been shifted before the crtc_enable and
the bridge post_disable calls have been shifted after the crtc_disable.
This has been done as per the definition of bridge pre_enable.
"The display pipe (i.e. clocks and timing signals) feeding this bridge
will not yet be running when this callback is called".
Since CRTC is also a source feeding the bridge, it should not be enabled
before the bridges in the pipeline are pre_enabled.
The sequence of enable after this patch will look like:
bridge[n]_pre_enable
...
bridge[1]_pre_enable
crtc_enable
encoder_enable
bridge[1]_enable
...
bridge[n]_enable
and vice-versa for the bridge chain disable sequence.
2. The cdns-dsi enable / disable sequences have now been moved to pre_enable
and post_disable sequences. This is the only way to have cdns-dsi drivers
be up and ready before the previous entity is enables its streaming.
The DSI also spec requires the Clock and Data Lanes be ready before the DSI TX
enables its stream[0]. A patch has been added to make the code wait for that to
happen. Going ahead with further DSI (and DSS configuration), while the lanes
are not ready, has been found to be another reason for shift in colors.
These patches have been tested with J721E based BeagleboneAI64 along with a
RaspberryPi 7" DSI panel. The extra patches can be found in the
"next_dsi_test-v5" branch of my github fork[1] for anyone who would like to test
them.
* Important note about the authorship of patches *
All the patches in the previous revisions of this series, as well as a majority
of this revision too have been authored when I owned a "ti.com" based email id,
i.e. <a-bhatia1@ti.com>. This email id is not in use anymore, and all the work
done later has been part of my personal work. Since the original patches were
authored using TI's email id, I have maintained the original authorships as they
are, as well as their sign offs.
I have further added another another sign off that uses my current (and
personal) email id, the one that is being used to send this revision,
i.e. <aradhya.bhatia@linux.dev>.
Thanks,
Aradhya
[0]: Section 12.6.5.7.3: "Start-up Procedure" [For DSI TX controller]
in TDA4VM Technical Reference Manual https://www.ti.com/lit/zip/spruil1
[1]: https://github.com/aradhya07/linux-ab/tree/next_dsi_test-v5
Change Log:
- Changes in v5:
- Fix subject and description in patch 1/13.
- Add patch to check the return value of
phy_mipi_dphy_get_default_config() (patch: 6/13).
- Change the Clk and Data Lane ready timeout from forever to 5s.
- Print an error instead of calling WARN_ON_ONCE in patch 7/13.
- Drop patch v4-07/11: "drm/bridge: cdns-dsi: Reset the DCS write FIFO".
There has been some inconsistencies found with this patch upon further
testing. This patch was being used to enable a DSI panel based on ILITEK
ILI9881C bridge. This will be debugged separately.
- Add patch to move the DSI mode check from _atomic_enable() to
_atomic_check() (patch: 10/13).
- Split patch v4-10/11 into 2 patches - 11/13 and 12/13.
Patch 11/13 separates out the Encoder-Bridge operations into a helper
function *without* changing the logic. Patch 12/13 then changes the order
of the encoder-bridge operations as was intended in the original patch.
- Add detailed comment for patch 13/13.
- Add Tomi Valkeinen's R-b in patches 1, 2, 4, 5, 7, 8, 9, 13.
- Changes in v4:
- Add new patch, "drm/bridge: cdns-dsi: Move to devm_drm_of_get_bridge()",
to update to an auto-managed way of finding next bridge in the chain.
- Drop patch "drm/bridge: cdns-dsi: Fix the phy_initialized variable" and
add "drm/bridge: cdns-dsi: Fix Phy _init() and _exit()" that properly
de-initializes the Phy and maintains the initialization state.
- Reword patch "drm/bridge: cdns-dsi: Reset the DCS write FIFO" to explain
the HW concerns better.
- Add R-b tag from Dmitry Baryshkov for patches 1/11 and 8/11.
- Changes in v3:
- Reword the commit message for patch "drm/bridge: cdns-dsi: Fix OF node
pointer".
- Add a new helper API to figure out DSI host input pixel format
in patch "drm/mipi-dsi: Add helper to find input format".
- Use a common function for bridge pre-enable and enable, and bridge disable
and post-disable, to avoid code duplication.
- Add T-b tag from Dominik Haller in patch 5/10. (Missed to add it in v2).
- Add R-b tag from Dmitry Baryshkov for patch 8/10.
- Changes in v2:
- Drop patch "drm/tidss: Add CRTC mode_fixup"
- Split patch "drm/bridge: cdns-dsi: Fix minor bugs" into 4 separate ones
- Drop support for early_enable/late_disable APIs and instead re-order the
pre_enable / post_disable APIs to be called before / after crtc_enable /
crtc_disable.
- Drop support for early_enable/late_disable in cdns-dsi and use
pre_enable/post_disable APIs instead to do bridge enable/disable.
Previous versions:
v1: https://lore.kernel.org/all/20240511153051.1355825-1-a-bhatia1@ti.com/
v2: https://lore.kernel.org/all/20240530093621.1925863-1-a-bhatia1@ti.com/
v3: https://lore.kernel.org/all/20240617105311.1587489-1-a-bhatia1@ti.com/
v4: https://lore.kernel.org/all/20240622110929.3115714-1-a-bhatia1@ti.com/
Aradhya Bhatia (13):
drm/bridge: cdns-dsi: Fix connecting to next bridge
drm/bridge: cdns-dsi: Move to devm_drm_of_get_bridge()
drm/bridge: cdns-dsi: Fix Phy _init() and _exit()
drm/bridge: cdns-dsi: Fix the link and phy init order
drm/bridge: cdns-dsi: Fix the clock variable for mode_valid()
drm/bridge: cdns-dsi: Check return value when getting default PHY
config
drm/bridge: cdns-dsi: Wait for Clk and Data Lanes to be ready
drm/mipi-dsi: Add helper to find input format
drm/bridge: cdns-dsi: Support atomic bridge APIs
drm/bridge: cdns-dsi: Move DSI mode check to _atomic_check()
drm/atomic-helper: Separate out Encoder-Bridge enable and disable
drm/atomic-helper: Re-order bridge chain pre-enable and post-disable
drm/bridge: cdns-dsi: Use pre_enable/post_disable to enable/disable
.../gpu/drm/bridge/cadence/cdns-dsi-core.c | 159 +++++++++++------
.../gpu/drm/bridge/cadence/cdns-dsi-core.h | 3 +-
drivers/gpu/drm/drm_atomic_helper.c | 163 +++++++++++-------
drivers/gpu/drm/drm_mipi_dsi.c | 37 ++++
include/drm/drm_atomic_helper.h | 5 +
include/drm/drm_mipi_dsi.h | 1 +
6 files changed, 255 insertions(+), 113 deletions(-)
base-commit: f2493655d2d3d5c6958ed996b043c821c23ae8d3
--
2.34.1