From: Yijie Yang <quic_yijiyang@quicinc.com>

Enable the SerDes PHY on qcs8300-ride.
Add the MDC and MDIO pin functions for ethernet0 on qcs8300-ride.
Enable the first 1Gb ethernet port on qcs8300-ride development board.

Signed-off-by: Yijie Yang <quic_yijiyang@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcs8300-ride.dts | 112 ++++++++++++++++++++++
 1 file changed, 112 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
index 7eed19a694c3..b1c9f2cb9749 100644
--- a/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
+++ b/arch/arm64/boot/dts/qcom/qcs8300-ride.dts
@@ -210,6 +210,95 @@ vreg_l9c: ldo9 {
 	};
 };
 
+&ethernet0 {
+	phy-mode = "sgmii";
+	phy-handle = <&sgmii_phy0>;
+
+	pinctrl-0 = <&ethernet0_default>;
+	pinctrl-names = "default";
+
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+	snps,ps-speed = <1000>;
+
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sgmii_phy0: phy@8 {
+			compatible = "ethernet-phy-id0141.0dd4";
+			reg = <0x8>;
+			device_type = "ethernet-phy";
+			interrupts-extended = <&tlmm 4 IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <11000>;
+			reset-deassert-us = <70000>;
+		};
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <4>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x1>;
+			snps,route-ptp;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x2>;
+			snps,route-avcp;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x3>;
+			snps,priority = <0xc>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <4>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+	};
+};
+
 &gcc {
 	clocks = <&rpmhcc RPMH_CXO_CLK>,
 		 <&sleep_clk>,
@@ -247,6 +336,29 @@ &rpmhcc {
 	clock-names = "xo";
 };
 
+&serdes0 {
+	phy-supply = <&vreg_l5a>;
+	status = "okay";
+};
+
+&tlmm {
+	ethernet0_default: ethernet0-default-state {
+		ethernet0_mdc: ethernet0-mdc-pins {
+			pins = "gpio5";
+			function = "emac0_mdc";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		ethernet0_mdio: ethernet0-mdio-pins {
+			pins = "gpio6";
+			function = "emac0_mdio";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+	};
+};
+
 &uart7 {
 	status = "okay";
 };
-- 
2.34.1

On 17.10.2024 12:27 PM, YijieYang wrote:
> From: Yijie Yang <quic_yijiyang@quicinc.com>
> 
> Enable the SerDes PHY on qcs8300-ride.
> Add the MDC and MDIO pin functions for ethernet0 on qcs8300-ride.
> Enable the first 1Gb ethernet port on qcs8300-ride development board.
> 
> Signed-off-by: Yijie Yang <quic_yijiyang@quicinc.com>
> ---

[...]

> +
> +&tlmm {
> +	ethernet0_default: ethernet0-default-state {
> +		ethernet0_mdc: ethernet0-mdc-pins {

If you don't intend to modify these specific configs, you can drop
the labels from child pin nodes

The rest looks good

Generally refactors happen first and features are added later, but
I know how painful it is to reorder changes in a patchset, so I'm
not going to ask you to do that.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad