Add Bluetooth and UART7 support for qcs6490-rb3gen2.

Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
---
 arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 120 +++++++++++++++++++
 1 file changed, 120 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
index 0d45662b8028..a5da7657e47e 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
@@ -32,6 +32,8 @@
 
 	aliases {
 		serial0 = &uart5;
+		bluetooth0 = &bluetooth;
+		serial1 = &uart7;
 	};
 
 	chosen {
@@ -688,6 +690,39 @@
 	status = "okay";
 };
 
+&qup_uart7_cts {
+	/*
+	 * Configure a bias-bus-hold on CTS to lower power
+	 * usage when Bluetooth is turned off. Bus hold will
+	 * maintain a low power state regardless of whether
+	 * the Bluetooth module drives the pin in either
+	 * direction or leaves the pin fully unpowered.
+	 */
+	bias-bus-hold;
+};
+
+&qup_uart7_rts {
+	/* We'll drive RTS, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart7_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	bias-pull-up;
+};
+
+&qup_uart7_tx {
+	/* We'll drive TX, so no pull */
+	drive-strength = <2>;
+	bias-disable;
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
@@ -719,12 +754,97 @@
 &tlmm {
 	gpio-reserved-ranges = <32 2>, /* ADSP */
 			       <48 4>; /* NFC */
+	bt_en: bt-en-state {
+		pins = "gpio85";
+		function = "gpio";
+		output-low;
+		bias-disable;
+	};
+
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
+		pins = "gpio28";
+		function = "gpio";
+		/*
+		 * Configure a bias-bus-hold on CTS to lower power
+		 * usage when Bluetooth is turned off. Bus hold will
+		 * maintain a low power state regardless of whether
+		 * the Bluetooth module drives the pin in either
+		 * direction or leaves the pin fully unpowered.
+		 */
+		bias-bus-hold;
+	};
+
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts-state {
+		pins = "gpio29";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx-state {
+		pins = "gpio31";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
+
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx-state {
+		pins = "gpio30";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+
+	sw_ctrl: sw-ctrl-state {
+		pins = "gpio86";
+		function = "gpio";
+		bias-pull-down;
+	};
 };
 
 &uart5 {
 	status = "okay";
 };
 
+&uart7 {
+	status = "okay";
+	/delete-property/interrupts;
+	interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>,
+			<&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+
+	bluetooth: bluetooth {
+		compatible = "qcom,wcn6750-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_en>, <&sw_ctrl>;
+		enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+		swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		vddaon-supply = <&vreg_s7b_0p972>;
+		vddbtcxmx-supply = <&vreg_s7b_0p972>;
+		vddrfacmn-supply = <&vreg_s7b_0p972>;
+		vddrfa0p8-supply = <&vreg_s7b_0p972>;
+		vddrfa1p7-supply = <&vreg_s1b_1p872>;
+		vddrfa1p2-supply = <&vreg_s8b_1p272>;
+		vddrfa2p2-supply = <&vreg_s1c_2p19>;
+		vddasd-supply = <&vreg_l11c_2p8>;
+		max-speed = <3200000>;
+	};
+};
+
 &usb_1 {
 	status = "okay";
 };
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

On Wed, 09 Oct 2024 16:44:36 +0530, Janaki Ramaiah Thota wrote:
> Add Bluetooth and UART7 support for qcs6490-rb3gen2.
> 
> Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 120 +++++++++++++++++++
>  1 file changed, 120 insertions(+)
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y qcom/qcs6490-rb3gen2.dtb' for 20241009111436.23473-1-quic_janathot@quicinc.com:

arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth: 'vddio-supply' is a required property
	from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#