1. Patchew
  2. linux
  3. View series

[PATCH v3] arm64: dts: qcom: sa8775p-ride: add WiFi/BT nodes

Miaoqing Pan posted 1 patch 1 month, 2 weeks ago
There is a newer version of this series
arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi | 121 +++++++++++++++++++++
arch/arm64/boot/dts/qcom/sa8775p.dtsi      |   2 +-
2 files changed, 122 insertions(+), 1 deletion(-)
[PATCH v3] arm64: dts: qcom: sa8775p-ride: add WiFi/BT nodes
Posted by Miaoqing Pan 1 month, 2 weeks ago 
Add a node for the PMU module of the WCN6855 present on the sa8775p-ride
board. Assign its LDO power outputs to the existing WiFi/Bluetooth module.

Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
---
v2:
  - fix wcn6855-pmu compatible to "qcom,wcn6855-pmu".
  - relocate pcieport0 node in alphabetical order.
v3:
  - add 'qcom,ath11k-calibration-variant = "SA8775P"'.

 arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi | 121 +++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sa8775p.dtsi      |   2 +-
 2 files changed, 122 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi
index 0c1b21def4b6..2546e9b86555 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi
@@ -27,6 +27,83 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	vreg_conn_1p8: vreg_conn_1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_conn_1p8";
+		startup-delay-us = <4000>;
+		enable-active-high;
+		gpio = <&pmm8654au_1_gpios 4 GPIO_ACTIVE_HIGH>;
+	};
+
+	vreg_conn_pa: vreg_conn_pa {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_conn_pa";
+		startup-delay-us = <4000>;
+		enable-active-high;
+		gpio = <&pmm8654au_1_gpios 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	wcn6855-pmu {
+		compatible = "qcom,wcn6855-pmu";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
+
+		vddio-supply = <&vreg_conn_pa>;
+		vddaon-supply = <&vreg_l2c>;
+		vddpmu-supply = <&vreg_conn_1p8>;
+		vddrfa0p95-supply = <&vreg_l2c>;
+		vddrfa1p3-supply = <&vreg_l6e>;
+		vddrfa1p9-supply = <&vreg_s5a>;
+		vddpcie1p3-supply = <&vreg_l6e>;
+		vddpcie1p9-supply = <&vreg_s5a>;
+
+		bt-enable-gpios = <&pmm8654au_1_gpios 8 GPIO_ACTIVE_HIGH>;
+		wlan-enable-gpios = <&pmm8654au_1_gpios 7 GPIO_ACTIVE_HIGH>;
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p7: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p7";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
 };
 
 &apps_rsc {
@@ -453,6 +530,20 @@ &pmm8654au_1_gpios {
 			  "USB2_PWR_EN",
 			  "USB2_FAULT";
 
+	wlan_en_state: wlan-en-state {
+		pins = "gpio7";
+		function = "normal";
+		output-low;
+		bias-pull-down;
+	};
+
+	bt_en_state: bt-en-state {
+		pins = "gpio8";
+		function = "normal";
+		output-low;
+		bias-pull-down;
+	};
+
 	usb2_en_state: usb2-en-state {
 		pins = "gpio9";
 		function = "normal";
@@ -702,6 +793,25 @@ &pcie1_phy {
 	status = "okay";
 };
 
+&pcieport0 {
+	wifi@0 {
+		compatible = "pci17cb,1101";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		qcom,ath11k-calibration-variant = "SA8775P";
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
 &remoteproc_adsp {
 	firmware-name = "qcom/sa8775p/adsp.mbn";
 	status = "okay";
@@ -744,6 +854,17 @@ &uart17 {
 	pinctrl-0 = <&qup_uart17_default>;
 	pinctrl-names = "default";
 	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn6855-bt";
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
+	};
 };
 
 &ufs_mem_hc {
diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
index e8dbc8d820a6..8d42b5e9c7d6 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
@@ -5570,7 +5570,7 @@ pcie0: pcie@1c00000 {
 
 		status = "disabled";
 
-		pcie@0 {
+		pcieport0: pcie@0 {
 			device_type = "pci";
 			reg = <0x0 0x0 0x0 0x0 0x0>;
 			bus-range = <0x01 0xff>;
-- 
2.25.1
Re: [PATCH v3] arm64: dts: qcom: sa8775p-ride: add WiFi/BT nodes
Posted by Dmitry Baryshkov 1 month, 2 weeks ago 
On Wed, Oct 09, 2024 at 09:27:38AM GMT, Miaoqing Pan wrote:
> Add a node for the PMU module of the WCN6855 present on the sa8775p-ride
> board. Assign its LDO power outputs to the existing WiFi/Bluetooth module.
> 
> Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
> ---
> v2:
>   - fix wcn6855-pmu compatible to "qcom,wcn6855-pmu".
>   - relocate pcieport0 node in alphabetical order.
> v3:
>   - add 'qcom,ath11k-calibration-variant = "SA8775P"'.
> 
>  arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi | 121 +++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sa8775p.dtsi      |   2 +-
>  2 files changed, 122 insertions(+), 1 deletion(-)
> 

[...]

> @@ -702,6 +793,25 @@ &pcie1_phy {
>  	status = "okay";
>  };
>  
> +&pcieport0 {
> +	wifi@0 {
> +		compatible = "pci17cb,1101";
> +		reg = <0x10000 0x0 0x0 0x0 0x0>;
> +
> +		qcom,ath11k-calibration-variant = "SA8775P";

SA8775P what? Is it going to be the only device using SA8775P?  Please
take a look around how other calibration variants are defined.

Also please cc Kalle, Jeff and ath11k ML in future submissions

> +
> +		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> +		vddaon-supply = <&vreg_pmu_aon_0p59>;
> +		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> +		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> +		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
> +		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
> +		vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
> +		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
> +		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
> +	};
> +};
> +
>  &remoteproc_adsp {
>  	firmware-name = "qcom/sa8775p/adsp.mbn";
>  	status = "okay";

-- 
With best wishes
Dmitry

Patchew 2.1-devel-b67e4c2

© 2016 - 2024 Red Hat, Inc.