For the i.MX95, configuration of a LUT is necessary to convert Bus Device
Function (BDF) to stream IDs, which are utilized by both IOMMU and ITS.
This involves examining the msi-map and smmu-map to ensure consistent
mapping of PCI BDF to the same stream IDs. Subsequently, LUT-related
registers are configured. In the absence of an msi-map, the built-in MSI
controller is utilized as a fallback.
Additionally, register a PCI bus callback function enable_device() and
disable_device() to config LUT when enable a new PCI device.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
change from v1 to v2
- set callback to pci_host_bridge instead pci->ops.
---
drivers/pci/controller/dwc/pci-imx6.c | 133 +++++++++++++++++++++++++++++++++-
1 file changed, 132 insertions(+), 1 deletion(-)
diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 94f3411352bf0..29186058ba256 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -55,6 +55,22 @@
#define IMX95_PE0_GEN_CTRL_3 0x1058
#define IMX95_PCIE_LTSSM_EN BIT(0)
+#define IMX95_PE0_LUT_ACSCTRL 0x1008
+#define IMX95_PEO_LUT_RWA BIT(16)
+#define IMX95_PE0_LUT_ENLOC GENMASK(4, 0)
+
+#define IMX95_PE0_LUT_DATA1 0x100c
+#define IMX95_PE0_LUT_VLD BIT(31)
+#define IMX95_PE0_LUT_DAC_ID GENMASK(10, 8)
+#define IMX95_PE0_LUT_STREAM_ID GENMASK(5, 0)
+
+#define IMX95_PE0_LUT_DATA2 0x1010
+#define IMX95_PE0_LUT_REQID GENMASK(31, 16)
+#define IMX95_PE0_LUT_MASK GENMASK(15, 0)
+
+#define IMX95_SID_MASK GENMASK(5, 0)
+#define IMX95_MAX_LUT 32
+
#define to_imx_pcie(x) dev_get_drvdata((x)->dev)
enum imx_pcie_variants {
@@ -82,6 +98,7 @@ enum imx_pcie_variants {
#define IMX_PCIE_FLAG_HAS_PHY_RESET BIT(5)
#define IMX_PCIE_FLAG_HAS_SERDES BIT(6)
#define IMX_PCIE_FLAG_SUPPORT_64BIT BIT(7)
+#define IMX_PCIE_FLAG_HAS_LUT BIT(8)
#define imx_check_flag(pci, val) (pci->drvdata->flags & val)
@@ -134,6 +151,7 @@ struct imx_pcie {
struct device *pd_pcie_phy;
struct phy *phy;
const struct imx_pcie_drvdata *drvdata;
+ struct mutex lock;
};
/* Parameters for the waiting for PCIe PHY PLL to lock on i.MX7 */
@@ -925,6 +943,111 @@ static void imx_pcie_stop_link(struct dw_pcie *pci)
imx_pcie_ltssm_disable(dev);
}
+static int imx_pcie_add_lut(struct imx_pcie *imx_pcie, u16 reqid, u8 sid)
+{
+ struct dw_pcie *pci = imx_pcie->pci;
+ struct device *dev = pci->dev;
+ u32 data1, data2;
+ int i;
+
+ if (sid >= 64) {
+ dev_err(dev, "Invalid SID for index %d\n", sid);
+ return -EINVAL;
+ }
+
+ guard(mutex)(&imx_pcie->lock);
+
+ for (i = 0; i < IMX95_MAX_LUT; i++) {
+ regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, IMX95_PEO_LUT_RWA | i);
+
+ regmap_read(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, &data1);
+ if (data1 & IMX95_PE0_LUT_VLD)
+ continue;
+
+ data1 = FIELD_PREP(IMX95_PE0_LUT_DAC_ID, 0);
+ data1 |= FIELD_PREP(IMX95_PE0_LUT_STREAM_ID, sid);
+ data1 |= IMX95_PE0_LUT_VLD;
+
+ regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, data1);
+
+ data2 = 0xffff;
+ data2 |= FIELD_PREP(IMX95_PE0_LUT_REQID, reqid);
+
+ regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, data2);
+
+ regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, i);
+
+ return 0;
+ }
+
+ dev_err(dev, "All lut already used\n");
+ return -EINVAL;
+}
+
+static void imx_pcie_remove_lut(struct imx_pcie *imx_pcie, u16 reqid)
+{
+ u32 data2 = 0;
+ int i;
+
+ guard(mutex)(&imx_pcie->lock);
+
+ for (i = 0; i < IMX95_MAX_LUT; i++) {
+ regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, IMX95_PEO_LUT_RWA | i);
+
+ regmap_read(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, &data2);
+ if (FIELD_GET(IMX95_PE0_LUT_REQID, data2) == reqid) {
+ regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, 0);
+ regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, 0);
+ regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, i);
+ }
+ }
+}
+
+static int imx_pcie_enable_device(struct pci_host_bridge *bridge, struct pci_dev *pdev)
+{
+ u32 sid_i = 0, sid_m = 0, rid = pci_dev_id(pdev);
+ struct imx_pcie *imx_pcie;
+ struct device *dev;
+ int err;
+
+ imx_pcie = to_imx_pcie(to_dw_pcie_from_pp(bridge->sysdata));
+ dev = imx_pcie->pci->dev;
+
+ err = of_map_id(dev->of_node, rid, "iommu-map", "iommu-map-mask", NULL, &sid_i);
+ if (err)
+ return err;
+
+ err = of_map_id(dev->of_node, rid, "msi-map", "msi-map-mask", NULL, &sid_m);
+ if (err)
+ return err;
+
+ if (sid_i != rid && sid_m != rid)
+ if ((sid_i & IMX95_SID_MASK) != (sid_m & IMX95_SID_MASK)) {
+ dev_err(dev, "its and iommu stream id miss match, please check dts file\n");
+ return -EINVAL;
+ }
+
+ /* if iommu-map is not existed then use msi-map's stream id*/
+ if (sid_i == rid)
+ sid_i = sid_m;
+
+ sid_i &= IMX95_SID_MASK;
+
+ if (sid_i != rid)
+ return imx_pcie_add_lut(imx_pcie, rid, sid_i);
+
+ /* Use dwc built-in MSI controller */
+ return 0;
+}
+
+static void imx_pcie_disable_device(struct pci_host_bridge *bridge, struct pci_dev *pdev)
+{
+ struct imx_pcie *imx_pcie;
+
+ imx_pcie = to_imx_pcie(to_dw_pcie_from_pp(bridge->sysdata));
+ imx_pcie_remove_lut(imx_pcie, pci_dev_id(pdev));
+}
+
static int imx_pcie_host_init(struct dw_pcie_rp *pp)
{
struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
@@ -941,6 +1064,11 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
}
}
+ if (pp->bridge && imx_check_flag(imx_pcie, IMX_PCIE_FLAG_HAS_LUT)) {
+ pp->bridge->enable_device = imx_pcie_enable_device;
+ pp->bridge->disable_device = imx_pcie_disable_device;
+ }
+
imx_pcie_assert_core_reset(imx_pcie);
if (imx_pcie->drvdata->init_phy)
@@ -1292,6 +1420,8 @@ static int imx_pcie_probe(struct platform_device *pdev)
imx_pcie->pci = pci;
imx_pcie->drvdata = of_device_get_match_data(dev);
+ mutex_init(&imx_pcie->lock);
+
/* Find the PHY if one is defined, only imx7d uses it */
np = of_parse_phandle(node, "fsl,imx7d-pcie-phy", 0);
if (np) {
@@ -1587,7 +1717,8 @@ static const struct imx_pcie_drvdata drvdata[] = {
},
[IMX95] = {
.variant = IMX95,
- .flags = IMX_PCIE_FLAG_HAS_SERDES,
+ .flags = IMX_PCIE_FLAG_HAS_SERDES |
+ IMX_PCIE_FLAG_HAS_LUT,
.clk_names = imx8mq_clks,
.clks_cnt = ARRAY_SIZE(imx8mq_clks),
.ltssm_off = IMX95_PE0_GEN_CTRL_3,
--
2.34.1On 2024-09-30 8:42 pm, Frank Li wrote:
> For the i.MX95, configuration of a LUT is necessary to convert Bus Device
> Function (BDF) to stream IDs, which are utilized by both IOMMU and ITS.
> This involves examining the msi-map and smmu-map to ensure consistent
> mapping of PCI BDF to the same stream IDs. Subsequently, LUT-related
> registers are configured. In the absence of an msi-map, the built-in MSI
> controller is utilized as a fallback.
>
> Additionally, register a PCI bus callback function enable_device() and
> disable_device() to config LUT when enable a new PCI device.
>
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> change from v1 to v2
> - set callback to pci_host_bridge instead pci->ops.
> ---
> drivers/pci/controller/dwc/pci-imx6.c | 133 +++++++++++++++++++++++++++++++++-
> 1 file changed, 132 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
> index 94f3411352bf0..29186058ba256 100644
> --- a/drivers/pci/controller/dwc/pci-imx6.c
> +++ b/drivers/pci/controller/dwc/pci-imx6.c
> @@ -55,6 +55,22 @@
> #define IMX95_PE0_GEN_CTRL_3 0x1058
> #define IMX95_PCIE_LTSSM_EN BIT(0)
>
> +#define IMX95_PE0_LUT_ACSCTRL 0x1008
> +#define IMX95_PEO_LUT_RWA BIT(16)
> +#define IMX95_PE0_LUT_ENLOC GENMASK(4, 0)
> +
> +#define IMX95_PE0_LUT_DATA1 0x100c
> +#define IMX95_PE0_LUT_VLD BIT(31)
> +#define IMX95_PE0_LUT_DAC_ID GENMASK(10, 8)
> +#define IMX95_PE0_LUT_STREAM_ID GENMASK(5, 0)
> +
> +#define IMX95_PE0_LUT_DATA2 0x1010
> +#define IMX95_PE0_LUT_REQID GENMASK(31, 16)
> +#define IMX95_PE0_LUT_MASK GENMASK(15, 0)
> +
> +#define IMX95_SID_MASK GENMASK(5, 0)
> +#define IMX95_MAX_LUT 32
> +
> #define to_imx_pcie(x) dev_get_drvdata((x)->dev)
>
> enum imx_pcie_variants {
> @@ -82,6 +98,7 @@ enum imx_pcie_variants {
> #define IMX_PCIE_FLAG_HAS_PHY_RESET BIT(5)
> #define IMX_PCIE_FLAG_HAS_SERDES BIT(6)
> #define IMX_PCIE_FLAG_SUPPORT_64BIT BIT(7)
> +#define IMX_PCIE_FLAG_HAS_LUT BIT(8)
>
> #define imx_check_flag(pci, val) (pci->drvdata->flags & val)
>
> @@ -134,6 +151,7 @@ struct imx_pcie {
> struct device *pd_pcie_phy;
> struct phy *phy;
> const struct imx_pcie_drvdata *drvdata;
> + struct mutex lock;
> };
>
> /* Parameters for the waiting for PCIe PHY PLL to lock on i.MX7 */
> @@ -925,6 +943,111 @@ static void imx_pcie_stop_link(struct dw_pcie *pci)
> imx_pcie_ltssm_disable(dev);
> }
>
> +static int imx_pcie_add_lut(struct imx_pcie *imx_pcie, u16 reqid, u8 sid)
> +{
> + struct dw_pcie *pci = imx_pcie->pci;
> + struct device *dev = pci->dev;
> + u32 data1, data2;
> + int i;
> +
> + if (sid >= 64) {
> + dev_err(dev, "Invalid SID for index %d\n", sid);
> + return -EINVAL;
> + }
> +
> + guard(mutex)(&imx_pcie->lock);
> +
> + for (i = 0; i < IMX95_MAX_LUT; i++) {
> + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, IMX95_PEO_LUT_RWA | i);
> +
> + regmap_read(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, &data1);
> + if (data1 & IMX95_PE0_LUT_VLD)
> + continue;
Maybe check if an existing entry already exists for the given RID?
> + data1 = FIELD_PREP(IMX95_PE0_LUT_DAC_ID, 0);
> + data1 |= FIELD_PREP(IMX95_PE0_LUT_STREAM_ID, sid);
> + data1 |= IMX95_PE0_LUT_VLD;
> +
> + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, data1);
> +
> + data2 = 0xffff;
> + data2 |= FIELD_PREP(IMX95_PE0_LUT_REQID, reqid);
> +
> + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, data2);
> +
> + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, i);
> +
> + return 0;
> + }
> +
> + dev_err(dev, "All lut already used\n");
> + return -EINVAL;
> +}
> +
> +static void imx_pcie_remove_lut(struct imx_pcie *imx_pcie, u16 reqid)
> +{
> + u32 data2 = 0;
> + int i;
> +
> + guard(mutex)(&imx_pcie->lock);
> +
> + for (i = 0; i < IMX95_MAX_LUT; i++) {
> + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, IMX95_PEO_LUT_RWA | i);
> +
> + regmap_read(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, &data2);
> + if (FIELD_GET(IMX95_PE0_LUT_REQID, data2) == reqid) {
> + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, 0);
> + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, 0);
> + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, i);
...plus then you could safely return early here.
> + }
> + }
> +}
> +
> +static int imx_pcie_enable_device(struct pci_host_bridge *bridge, struct pci_dev *pdev)
> +{
> + u32 sid_i = 0, sid_m = 0, rid = pci_dev_id(pdev);
> + struct imx_pcie *imx_pcie;
> + struct device *dev;
> + int err;
> +
> + imx_pcie = to_imx_pcie(to_dw_pcie_from_pp(bridge->sysdata));
> + dev = imx_pcie->pci->dev;
> +
> + err = of_map_id(dev->of_node, rid, "iommu-map", "iommu-map-mask", NULL, &sid_i);
> + if (err)
> + return err;
> +
> + err = of_map_id(dev->of_node, rid, "msi-map", "msi-map-mask", NULL, &sid_m);
> + if (err)
> + return err;
> +
> + if (sid_i != rid && sid_m != rid)
Perhaps it is reasonable to assume that i.MX95 will never have SMMU/ITS
mappings for low-numbered devices on bus 0, but in general this isn't
very robust, and either way it's certainly not all that clear at first
glance what assmuption is actually being made here. If it's significant
whether a mapping actually exists or not for the given ID then you
should really use the "target" argument of of_map_id() to determine that.
> + if ((sid_i & IMX95_SID_MASK) != (sid_m & IMX95_SID_MASK)) {
> + dev_err(dev, "its and iommu stream id miss match, please check dts file\n");
> + return -EINVAL;
> + }
> +
> + /* if iommu-map is not existed then use msi-map's stream id*/
> + if (sid_i == rid)
> + sid_i = sid_m;
> +
> + sid_i &= IMX95_SID_MASK;
AFAICS this means that:
a) the check in imx_pcie_add_lut() is useless, since if a mapping had an
output ID larger than 63, then we've now just silently truncated the LUT
entry to not match what the SMMU/ITS will still expect.
b) if no mapping existed, then we're going to needlessly allocate a LUT
entry anyway since the truncated RID now won't match the original.
> +
> + if (sid_i != rid)
> + return imx_pcie_add_lut(imx_pcie, rid, sid_i);
> +
> + /* Use dwc built-in MSI controller */
This comment seems out of place - how does returning 0 from here vs.
returning 0 from imx_pcie_add_lut() achieve that? I don't see any
obvious way for the LUT programming to influence the IRQ subsystem here :/
Thanks,
Robin.
> + return 0;
> +}
> +
> +static void imx_pcie_disable_device(struct pci_host_bridge *bridge, struct pci_dev *pdev)
> +{
> + struct imx_pcie *imx_pcie;
> +
> + imx_pcie = to_imx_pcie(to_dw_pcie_from_pp(bridge->sysdata));
> + imx_pcie_remove_lut(imx_pcie, pci_dev_id(pdev));
> +}
> +
> static int imx_pcie_host_init(struct dw_pcie_rp *pp)
> {
> struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> @@ -941,6 +1064,11 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
> }
> }
>
> + if (pp->bridge && imx_check_flag(imx_pcie, IMX_PCIE_FLAG_HAS_LUT)) {
> + pp->bridge->enable_device = imx_pcie_enable_device;
> + pp->bridge->disable_device = imx_pcie_disable_device;
> + }
> +
> imx_pcie_assert_core_reset(imx_pcie);
>
> if (imx_pcie->drvdata->init_phy)
> @@ -1292,6 +1420,8 @@ static int imx_pcie_probe(struct platform_device *pdev)
> imx_pcie->pci = pci;
> imx_pcie->drvdata = of_device_get_match_data(dev);
>
> + mutex_init(&imx_pcie->lock);
> +
> /* Find the PHY if one is defined, only imx7d uses it */
> np = of_parse_phandle(node, "fsl,imx7d-pcie-phy", 0);
> if (np) {
> @@ -1587,7 +1717,8 @@ static const struct imx_pcie_drvdata drvdata[] = {
> },
> [IMX95] = {
> .variant = IMX95,
> - .flags = IMX_PCIE_FLAG_HAS_SERDES,
> + .flags = IMX_PCIE_FLAG_HAS_SERDES |
> + IMX_PCIE_FLAG_HAS_LUT,
> .clk_names = imx8mq_clks,
> .clks_cnt = ARRAY_SIZE(imx8mq_clks),
> .ltssm_off = IMX95_PE0_GEN_CTRL_3,
>
On Thu, Oct 03, 2024 at 12:16:42PM +0100, Robin Murphy wrote:
> On 2024-09-30 8:42 pm, Frank Li wrote:
> > For the i.MX95, configuration of a LUT is necessary to convert Bus Device
> > Function (BDF) to stream IDs, which are utilized by both IOMMU and ITS.
> > This involves examining the msi-map and smmu-map to ensure consistent
> > mapping of PCI BDF to the same stream IDs. Subsequently, LUT-related
> > registers are configured. In the absence of an msi-map, the built-in MSI
> > controller is utilized as a fallback.
> >
> > Additionally, register a PCI bus callback function enable_device() and
> > disable_device() to config LUT when enable a new PCI device.
> >
> > Signed-off-by: Frank Li <Frank.Li@nxp.com>
> > ---
> > change from v1 to v2
> > - set callback to pci_host_bridge instead pci->ops.
> > ---
> > drivers/pci/controller/dwc/pci-imx6.c | 133 +++++++++++++++++++++++++++++++++-
> > 1 file changed, 132 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
> > index 94f3411352bf0..29186058ba256 100644
> > --- a/drivers/pci/controller/dwc/pci-imx6.c
> > +++ b/drivers/pci/controller/dwc/pci-imx6.c
> > @@ -55,6 +55,22 @@
> > #define IMX95_PE0_GEN_CTRL_3 0x1058
> > #define IMX95_PCIE_LTSSM_EN BIT(0)
> > +#define IMX95_PE0_LUT_ACSCTRL 0x1008
> > +#define IMX95_PEO_LUT_RWA BIT(16)
> > +#define IMX95_PE0_LUT_ENLOC GENMASK(4, 0)
> > +
> > +#define IMX95_PE0_LUT_DATA1 0x100c
> > +#define IMX95_PE0_LUT_VLD BIT(31)
> > +#define IMX95_PE0_LUT_DAC_ID GENMASK(10, 8)
> > +#define IMX95_PE0_LUT_STREAM_ID GENMASK(5, 0)
> > +
> > +#define IMX95_PE0_LUT_DATA2 0x1010
> > +#define IMX95_PE0_LUT_REQID GENMASK(31, 16)
> > +#define IMX95_PE0_LUT_MASK GENMASK(15, 0)
> > +
> > +#define IMX95_SID_MASK GENMASK(5, 0)
> > +#define IMX95_MAX_LUT 32
> > +
> > #define to_imx_pcie(x) dev_get_drvdata((x)->dev)
> > enum imx_pcie_variants {
> > @@ -82,6 +98,7 @@ enum imx_pcie_variants {
> > #define IMX_PCIE_FLAG_HAS_PHY_RESET BIT(5)
> > #define IMX_PCIE_FLAG_HAS_SERDES BIT(6)
> > #define IMX_PCIE_FLAG_SUPPORT_64BIT BIT(7)
> > +#define IMX_PCIE_FLAG_HAS_LUT BIT(8)
> > #define imx_check_flag(pci, val) (pci->drvdata->flags & val)
> > @@ -134,6 +151,7 @@ struct imx_pcie {
> > struct device *pd_pcie_phy;
> > struct phy *phy;
> > const struct imx_pcie_drvdata *drvdata;
> > + struct mutex lock;
> > };
> > /* Parameters for the waiting for PCIe PHY PLL to lock on i.MX7 */
> > @@ -925,6 +943,111 @@ static void imx_pcie_stop_link(struct dw_pcie *pci)
> > imx_pcie_ltssm_disable(dev);
> > }
> > +static int imx_pcie_add_lut(struct imx_pcie *imx_pcie, u16 reqid, u8 sid)
> > +{
> > + struct dw_pcie *pci = imx_pcie->pci;
> > + struct device *dev = pci->dev;
> > + u32 data1, data2;
> > + int i;
> > +
> > + if (sid >= 64) {
> > + dev_err(dev, "Invalid SID for index %d\n", sid);
> > + return -EINVAL;
> > + }
> > +
> > + guard(mutex)(&imx_pcie->lock);
> > +
> > + for (i = 0; i < IMX95_MAX_LUT; i++) {
> > + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, IMX95_PEO_LUT_RWA | i);
> > +
> > + regmap_read(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, &data1);
> > + if (data1 & IMX95_PE0_LUT_VLD)
> > + continue;
>
> Maybe check if an existing entry already exists for the given RID?
>
> > + data1 = FIELD_PREP(IMX95_PE0_LUT_DAC_ID, 0);
> > + data1 |= FIELD_PREP(IMX95_PE0_LUT_STREAM_ID, sid);
> > + data1 |= IMX95_PE0_LUT_VLD;
> > +
> > + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, data1);
> > +
> > + data2 = 0xffff;
> > + data2 |= FIELD_PREP(IMX95_PE0_LUT_REQID, reqid);
> > +
> > + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, data2);
> > +
> > + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, i);
> > +
> > + return 0;
> > + }
> > +
> > + dev_err(dev, "All lut already used\n");
> > + return -EINVAL;
> > +}
> > +
> > +static void imx_pcie_remove_lut(struct imx_pcie *imx_pcie, u16 reqid)
> > +{
> > + u32 data2 = 0;
> > + int i;
> > +
> > + guard(mutex)(&imx_pcie->lock);
> > +
> > + for (i = 0; i < IMX95_MAX_LUT; i++) {
> > + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, IMX95_PEO_LUT_RWA | i);
> > +
> > + regmap_read(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, &data2);
> > + if (FIELD_GET(IMX95_PE0_LUT_REQID, data2) == reqid) {
> > + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA1, 0);
> > + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_DATA2, 0);
> > + regmap_write(imx_pcie->iomuxc_gpr, IMX95_PE0_LUT_ACSCTRL, i);
>
> ...plus then you could safely return early here.
>
> > + }
> > + }
> > +}
> > +
> > +static int imx_pcie_enable_device(struct pci_host_bridge *bridge, struct pci_dev *pdev)
> > +{
> > + u32 sid_i = 0, sid_m = 0, rid = pci_dev_id(pdev);
> > + struct imx_pcie *imx_pcie;
> > + struct device *dev;
> > + int err;
> > +
> > + imx_pcie = to_imx_pcie(to_dw_pcie_from_pp(bridge->sysdata));
> > + dev = imx_pcie->pci->dev;
> > +
> > + err = of_map_id(dev->of_node, rid, "iommu-map", "iommu-map-mask", NULL, &sid_i);
> > + if (err)
> > + return err;
> > +
> > + err = of_map_id(dev->of_node, rid, "msi-map", "msi-map-mask", NULL, &sid_m);
> > + if (err)
> > + return err;
> > +
> > + if (sid_i != rid && sid_m != rid)
>
> Perhaps it is reasonable to assume that i.MX95 will never have SMMU/ITS
> mappings for low-numbered devices on bus 0, but in general this isn't very
> robust, and either way it's certainly not all that clear at first glance
> what assmuption is actually being made here. If it's significant whether a
> mapping actually exists or not for the given ID then you should really use
> the "target" argument of of_map_id() to determine that.
let me do more research on this.
The key part is patch 1.
Frank
>
> > + if ((sid_i & IMX95_SID_MASK) != (sid_m & IMX95_SID_MASK)) {
> > + dev_err(dev, "its and iommu stream id miss match, please check dts file\n");
> > + return -EINVAL;
> > + }
> > +
> > + /* if iommu-map is not existed then use msi-map's stream id*/
> > + if (sid_i == rid)
> > + sid_i = sid_m;
> > +
> > + sid_i &= IMX95_SID_MASK;
>
> AFAICS this means that:
> a) the check in imx_pcie_add_lut() is useless, since if a mapping had an
> output ID larger than 63, then we've now just silently truncated the LUT
> entry to not match what the SMMU/ITS will still expect.
> b) if no mapping existed, then we're going to needlessly allocate a LUT
> entry anyway since the truncated RID now won't match the original.
You are right. It is my mistake.
>
> > +
> > + if (sid_i != rid)
> > + return imx_pcie_add_lut(imx_pcie, rid, sid_i);
> > +
> > + /* Use dwc built-in MSI controller */
>
> This comment seems out of place - how does returning 0 from here vs.
> returning 0 from imx_pcie_add_lut() achieve that? I don't see any obvious
> way for the LUT programming to influence the IRQ subsystem here :/
If msi-map is not existed. sid_i will equal to rid. imx_pcie_add_lut()
will be skipped. PCI controller still fallback to the dwc built-in's MSI
controller.
msi-map iommu-map
Y Y ITS + SMMU, require the same sid
Y N ITS
N Y DWC MSI Ctrl + SMMU
N N DWC MSI Ctrl. (current upstream state)
Return 0 here, it is N-N case.
>
> Thanks,
> Robin.
>
> > + return 0;
> > +}
> > +
> > +static void imx_pcie_disable_device(struct pci_host_bridge *bridge, struct pci_dev *pdev)
> > +{
> > + struct imx_pcie *imx_pcie;
> > +
> > + imx_pcie = to_imx_pcie(to_dw_pcie_from_pp(bridge->sysdata));
> > + imx_pcie_remove_lut(imx_pcie, pci_dev_id(pdev));
> > +}
> > +
> > static int imx_pcie_host_init(struct dw_pcie_rp *pp)
> > {
> > struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> > @@ -941,6 +1064,11 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
> > }
> > }
> > + if (pp->bridge && imx_check_flag(imx_pcie, IMX_PCIE_FLAG_HAS_LUT)) {
> > + pp->bridge->enable_device = imx_pcie_enable_device;
> > + pp->bridge->disable_device = imx_pcie_disable_device;
> > + }
> > +
> > imx_pcie_assert_core_reset(imx_pcie);
> > if (imx_pcie->drvdata->init_phy)
> > @@ -1292,6 +1420,8 @@ static int imx_pcie_probe(struct platform_device *pdev)
> > imx_pcie->pci = pci;
> > imx_pcie->drvdata = of_device_get_match_data(dev);
> > + mutex_init(&imx_pcie->lock);
> > +
> > /* Find the PHY if one is defined, only imx7d uses it */
> > np = of_parse_phandle(node, "fsl,imx7d-pcie-phy", 0);
> > if (np) {
> > @@ -1587,7 +1717,8 @@ static const struct imx_pcie_drvdata drvdata[] = {
> > },
> > [IMX95] = {
> > .variant = IMX95,
> > - .flags = IMX_PCIE_FLAG_HAS_SERDES,
> > + .flags = IMX_PCIE_FLAG_HAS_SERDES |
> > + IMX_PCIE_FLAG_HAS_LUT,
> > .clk_names = imx8mq_clks,
> > .clks_cnt = ARRAY_SIZE(imx8mq_clks),
> > .ltssm_off = IMX95_PE0_GEN_CTRL_3,
> >
>
© 2016 - 2024 Red Hat, Inc.