The Xunlong Orange Pi 3B is a single-board computer based on the
Rockchip RK3566 SoC.
Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
v2:
- Add DT for v2.1 hw revision, rename initial DT to v1.1:
- Ethernet phy io voltage: 3v3 (v1.1) / 1v8 (v2.1)
- Etherent reset gpios: GPIO3_C2 (v1.1) / GPIO4_C4 (v2.1)
- WiFi/BT: CDW-20U5622 (v1.1) / AP6256 (v2.1)
- Rename led node and move led pinctrl props
- Use regulator-.* nodename for fixed regulators
- Drop rockchip,mic-in-differential prop
- Add cap-mmc-highspeed to sdhci node
- Add no-mmc and no-sd to sdmmc1 node
Following issue is reported by dtbs_check and is fixed by series at [1]:
pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks'
do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
[1] https://lore.kernel.org/all/20240622-rk809-fixes-v2-0-c0db420d3639@collabora.com/
---
arch/arm64/boot/dts/rockchip/Makefile | 2 +
.../dts/rockchip/rk3566-orangepi-3b-v1.1.dts | 29 +
.../dts/rockchip/rk3566-orangepi-3b-v2.1.dts | 70 ++
.../boot/dts/rockchip/rk3566-orangepi-3b.dtsi | 678 ++++++++++++++++++
4 files changed, 779 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ae0ae02f51e9..df5a74c407f4 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -81,6 +81,8 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353ps.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353v.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353vs.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg503.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-orangepi-3b-v1.1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-orangepi-3b-v2.1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinetab2-v0.1.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
new file mode 100644
index 000000000000..074e93bd4b85
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-orangepi-3b.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi 3B v1.1";
+ compatible = "xunlong,orangepi-3b-v1.1", "xunlong,orangepi-3b", "rockchip,rk3566";
+};
+
+&pmu_io_domains {
+ vccio5-supply = <&vcc_3v3>;
+};
+
+&gmac1 {
+ phy-handle = <&rgmii_phy1>;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts
new file mode 100644
index 000000000000..d894bff41e61
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dts
@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-orangepi-3b.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi 3B v2.1";
+ compatible = "xunlong,orangepi-3b-v2.1", "xunlong,orangepi-3b", "rockchip,rk3566";
+
+ vccio_phy1: regulator-1v8-vccio-phy {
+ compatible = "regulator-fixed";
+ regulator-name = "vccio_phy1";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ };
+};
+
+&pmu_io_domains {
+ vccio5-supply = <&vccio_phy1>;
+};
+
+&gmac1 {
+ phy-handle = <&rgmii_phy1>;
+ status = "okay";
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&sdmmc1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ brcmf: wifi@1 {
+ compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PD6 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_wake_host_h>;
+ };
+};
+
+&uart1 {
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ clocks = <&rk809 1>;
+ clock-names = "lpo";
+ interrupt-parent = <&gpio2>;
+ interrupts = <RK_PC0 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wakeup";
+ device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+ shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_reg_on_h &bt_wake_host_h &host_wake_bt_h>;
+ vbat-supply = <&vcc_3v3>;
+ vddio-supply = <&vcc_1v8>;
+ };
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi
new file mode 100644
index 000000000000..d539570f531e
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b.dtsi
@@ -0,0 +1,678 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi 3B";
+ compatible = "xunlong,orangepi-3b", "rockchip,rk3566";
+
+ aliases {
+ ethernet0 = &gmac1;
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc0;
+ mmc2 = &sdmmc1;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&work_led>;
+
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "on";
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ vcc3v3_pcie30: regulator-3v3-vcc-pcie30 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie20_pwren>;
+ regulator-name = "vcc3v3_pcie30";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc3v3_sys>;
+ };
+
+ vcc3v3_sys: regulator-3v3-vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_sys: regulator-5v0-vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_usb_host: regulator-5v0-vcc-usb-host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_host_pwren_h>;
+ regulator-name = "vcc5v0_usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_usb_otg: regulator-5v0-vcc-usb-otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_otg_pwren_h>;
+ regulator-name = "vcc5v0_usb_otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_reg_on_h>;
+ post-power-on-delay-ms = <200>;
+ power-off-delay-us = <5000000>;
+ reset-gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Analog RK809";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rk809>;
+ };
+ };
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+ clock_in_out = "input";
+ phy-mode = "rgmii-id";
+ phy-supply = <&vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m0_miim
+ &gmac1m0_tx_bus2
+ &gmac1m0_rx_bus2
+ &gmac1m0_rgmii_clk
+ &gmac1m0_rgmii_bus
+ &gmac1m0_clkinout>;
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ clock-names = "mclk";
+ clock-output-names = "rk809-clkout1", "rk809-clkout2";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
+ #sound-dai-cells = <0>;
+ system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+
+ vdd_cpu: regulator@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <830000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc3v3_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&pcie2x1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie20_pins>;
+ reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie30>;
+ status = "okay";
+};
+
+&pinctrl {
+ bluetooth {
+ bt_reg_on_h: bt-reg-on-h {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_wake_host_h: bt-wake-host-h {
+ rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ host_wake_bt_h: host-wake-bt-h {
+ rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ work_led: work-led {
+ rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ pcie20_pins: pcie20-pins {
+ rockchip,pins =
+ <1 RK_PB0 4 &pcfg_pull_none>,
+ <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>,
+ <1 RK_PB1 4 &pcfg_pull_none>;
+ };
+
+ pcie20_pwren: pcie20-pwren {
+ rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb {
+ usb_host_pwren_h: usb-host-pwren-h {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usb_otg_pwren_h: usb-otg-pwren-h {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ wifi_reg_on_h: wifi-reg-on-h {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wifi_wake_host_h: wifi-wake-host-h {
+ rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio6-supply = <&vcc_3v3>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ max-frequency = <200000000>;
+ mmc-hs200-1_8v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdmmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ no-mmc;
+ no-sd;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_clk &sdmmc1_cmd>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sfc {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <104000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ };
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb_otg>;
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_host {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
--
2.45.2On 6/27/24 2:03 AM, Jonas Karlman wrote:
> The Xunlong Orange Pi 3B is a single-board computer based on the
> Rockchip RK3566 SoC.
...> +
> +&gmac1 {
> + phy-handle = <&rgmii_phy1>;
> + status = "okay";
> +};
> +
> +&mdio1 {
> + rgmii_phy1: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
Jonas, were you able to test V1.1 board's Ethernet?
Whenever I start the board - Ethernet initialization fails with:
```
[ 21.140055] rk_gmac-dwmac fe010000.ethernet eth0: __stmmac_open:
Cannot attach to PHY (error: -19)
```
But if reset is performed inside gmac - initialization succeeds.
Eg. patch:
```
---
linux-6.12.17.orig/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
+++ linux-6.12.17/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
@@ -16,14 +16,14 @@
&gmac1 {
phy-handle = <&rgmii_phy1>;
status = "okay";
+ snps,reset-gpio = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 50000 200000>;
};
&mdio1 {
rgmii_phy1: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <1>;
- reset-assert-us = <20000>;
- reset-deassert-us = <50000>;
- reset-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
};
};
```
> + reset-assert-us = <20000>;
> + reset-deassert-us = <50000>;
> + reset-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
> + };
> +};
Arturas Moskvinas
Hi Arturas,
On 2025-03-08 15:53, Arturas Moskvinas wrote:
> On 6/27/24 2:03 AM, Jonas Karlman wrote:
>
>> The Xunlong Orange Pi 3B is a single-board computer based on the
>> Rockchip RK3566 SoC.
> ...> +
>> +&gmac1 {
>> + phy-handle = <&rgmii_phy1>;
>> + status = "okay";
>> +};
>> +
>> +&mdio1 {
>> + rgmii_phy1: ethernet-phy@1 {
>> + compatible = "ethernet-phy-ieee802.3-c22";
>> + reg = <1>;
>
> Jonas, were you able to test V1.1 board's Ethernet?
Yes, I have both a v1.1.1 and v2.1 hw revision of this board and
Ethernet should be working on both hw revisions.
>
> Whenever I start the board - Ethernet initialization fails with:
> ```
> [ 21.140055] rk_gmac-dwmac fe010000.ethernet eth0: __stmmac_open:
> Cannot attach to PHY (error: -19)
> ```
This is because of a reset issue with Ethernet PHYs in Linux, see [1].
Two workarounds:
1. Let boot firmware reset the PHY before Linux, i.e. use U-Boot
v2024.10 or newer.
2. Use a ethernet-phy-id compatible with correct phy-id to force Linux
to attach the PHY.
I suggest you try to wipe U-Boot from SPI flash on your board and update
to use U-Boot v2025.01 and try again.
>
> But if reset is performed inside gmac - initialization succeeds.
Use of deprecated snps,reset- props is not a proper fix for this issue,
instead Linux could use an improve Ethernet PHY initialization handling
and ensuring the PHY is reset before it tries to read a phy-id from it.
[1] https://lore.kernel.org/r/47d55aca-bee6-810f-379f-9431649fefa6@kwiboo.se/
Regards,
Jonas
>
> Eg. patch:
> ```
> ---
> linux-6.12.17.orig/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
> +++ linux-6.12.17/arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dts
> @@ -16,14 +16,14 @@
> &gmac1 {
> phy-handle = <&rgmii_phy1>;
> status = "okay";
> + snps,reset-gpio = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 50000 200000>;
> };
>
> &mdio1 {
> rgmii_phy1: ethernet-phy@1 {
> compatible = "ethernet-phy-ieee802.3-c22";
> reg = <1>;
> - reset-assert-us = <20000>;
> - reset-deassert-us = <50000>;
> - reset-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
> };
> };
> ```
>> + reset-assert-us = <20000>;
>> + reset-deassert-us = <50000>;
>> + reset-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
>> + };
>> +};
>
>
> Arturas Moskvinas
On 3/8/25 6:34 PM, Jonas Karlman wrote: > This is because of a reset issue with Ethernet PHYs in Linux, see [1]. > > Two workarounds: > 1. Let boot firmware reset the PHY before Linux, i.e. use U-Boot > v2024.10 or newer. > 2. Use a ethernet-phy-id compatible with correct phy-id to force Linux > to attach the PHY. > > I suggest you try to wipe U-Boot from SPI flash on your board and update > to use U-Boot v2025.01 and try again. Wiping board SPI flash which contained old U-boot and using 2025.01 from SD card fixed issue hence DTS is OK. Though I do not remember that I ever wrote anything into SPI flash in first place (I touched board almost year ago so potentially forgot about it) maybe it was shipped like that with the board... Arturas Moskvinas
Hi Jonas, kernel test robot noticed the following build warnings: [auto build test WARNING on rockchip/for-next] [also build test WARNING on robh/for-next krzk/for-next krzk-dt/for-next krzk-mem-ctrl/for-next linus/master v6.10-rc5 next-20240627] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Jonas-Karlman/dt-bindings-arm-rockchip-Add-Xunlong-Orange-Pi-3B/20240627-175050 base: https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git for-next patch link: https://lore.kernel.org/r/20240626230319.1425316-3-jonas%40kwiboo.se patch subject: [PATCH v2 2/2] arm64: dts: rockchip: Add Xunlong Orange Pi 3B config: arm64-randconfig-051-20240628 (https://download.01.org/0day-ci/archive/20240628/202406281834.nNnojcHy-lkp@intel.com/config) compiler: aarch64-linux-gcc (GCC) 13.2.0 dtschema version: 2024.6.dev3+g650bf2d reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240628/202406281834.nNnojcHy-lkp@intel.com/reproduce) If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags | Reported-by: kernel test robot <lkp@intel.com> | Closes: https://lore.kernel.org/oe-kbuild-all/202406281834.nNnojcHy-lkp@intel.com/ dtcheck warnings: (new ones prefixed by >>) >> arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml# -- >> arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml# -- 0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests/wiki
Hi Jonas, kernel test robot noticed the following build warnings: [auto build test WARNING on rockchip/for-next] [also build test WARNING on robh/for-next krzk/for-next krzk-dt/for-next krzk-mem-ctrl/for-next linus/master v6.10-rc5 next-20240627] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Jonas-Karlman/dt-bindings-arm-rockchip-Add-Xunlong-Orange-Pi-3B/20240627-175050 base: https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git for-next patch link: https://lore.kernel.org/r/20240626230319.1425316-3-jonas%40kwiboo.se patch subject: [PATCH v2 2/2] arm64: dts: rockchip: Add Xunlong Orange Pi 3B config: arm64-randconfig-051-20240628 (https://download.01.org/0day-ci/archive/20240628/202406280724.E053qdhz-lkp@intel.com/config) compiler: aarch64-linux-gcc (GCC) 13.2.0 dtschema version: 2024.6.dev2+g3b69bad reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240628/202406280724.E053qdhz-lkp@intel.com/reproduce) If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags | Reported-by: kernel test robot <lkp@intel.com> | Closes: https://lore.kernel.org/oe-kbuild-all/202406280724.E053qdhz-lkp@intel.com/ dtcheck warnings: (new ones prefixed by >>) >> arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v1.1.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml# -- >> arch/arm64/boot/dts/rockchip/rk3566-orangepi-3b-v2.1.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml# -- 0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests/wiki
© 2016 - 2025 Red Hat, Inc.