The Radxa ROCK 3B is a single-board computer based on the Pico-ITX form
factor (100mm x 75mm). Two versions of the ROCK 3B exists, a community
version based on the RK3568 SoC and an industrial version based on the
RK3568J SoC.
Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
---
v2:
- Use regulator-.* nodename for fixed regulators
- Drop rockchip,mic-in-differential prop
- Shorten Ethernet phy reset-deassert-us to 50 ms
- Fix pcie pinctrl
- Add keep-power-in-suspend to sdmmc2
Following issue is reported by dtbs_check and is fixed by series at [1]:
pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks'
do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
[1] https://lore.kernel.org/all/20240622-rk809-fixes-v2-0-c0db420d3639@collabora.com/
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../boot/dts/rockchip/rk3568-rock-3b.dts | 780 ++++++++++++++++++
2 files changed, 781 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 90f5172f37e6..ae0ae02f51e9 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -114,6 +114,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3b.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
new file mode 100644
index 000000000000..46c959f1c6ad
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
@@ -0,0 +1,780 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3568.dtsi"
+
+/ {
+ model = "Radxa ROCK 3B";
+ compatible = "radxa,rock-3b", "rockchip,rk3568";
+
+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc0;
+ mmc2 = &sdmmc2;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_ir>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "on";
+ function = LED_FUNCTION_HEARTBEAT;
+ gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led>;
+ };
+ };
+
+ /* pi6c pcie clock generator */
+ vcc3v3_pi6c_03: regulator-3v3-vcc-pi6c-03 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pwren_h>;
+ regulator-name = "vcc3v3_pi6c_03";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <10000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_sys: regulator-3v3-vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_sys2: regulator-3v3-vcc-sys2 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys2";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_sys: regulator-5v0-vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_usb_host: regulator-5v0-vcc-usb-host {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_host_pwren_h>;
+ regulator-name = "vcc5v0_usb_host";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_usb_otg: regulator-5v0-vcc-usb-otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_otg_pwren_h>;
+ regulator-name = "vcc5v0_usb_otg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rk809 1>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_reg_on_h>;
+ post-power-on-delay-ms = <100>;
+ power-off-delay-us = <5000000>;
+ reset-gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_LOW>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Analog RK809";
+ simple-audio-card,mclk-fs = <256>;
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s1_8ch>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&rk809>;
+ };
+ };
+};
+
+&combphy0 {
+ status = "okay";
+};
+
+&combphy1 {
+ status = "okay";
+};
+
+&combphy2 {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&gmac0 {
+ assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+ assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
+ clock_in_out = "input";
+ phy-handle = <&rgmii_phy0>;
+ phy-mode = "rgmii-id";
+ phy-supply = <&vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus
+ &gmac0_clkinout>;
+ status = "okay";
+};
+
+&gmac1 {
+ assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+ assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+ clock_in_out = "input";
+ phy-handle = <&rgmii_phy1>;
+ phy-mode = "rgmii-id";
+ phy-supply = <&vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1m1_miim
+ &gmac1m1_tx_bus2
+ &gmac1m1_rx_bus2
+ &gmac1m1_rgmii_clk
+ &gmac1m1_rgmii_bus
+ &gmac1m1_clkinout>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&hdmi {
+ avdd-0v9-supply = <&vdda0v9_image>;
+ avdd-1v8-supply = <&vcca1v8_image>;
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: regulator@1c {
+ compatible = "tcs,tcs4525";
+ reg = <0x1c>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ rk809: pmic@20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+ assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+ #clock-cells = <1>;
+ clocks = <&cru I2S1_MCLKOUT_TX>;
+ clock-names = "mclk";
+ clock-output-names = "rk809-clkout1", "rk809-clkout2";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
+ #sound-dai-cells = <0>;
+ system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c5 {
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <0>;
+ clock-output-names = "rtcic_32kout";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rtcic_int_l>;
+ wakeup-source;
+ };
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&i2s1_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s1m0_sclktx
+ &i2s1m0_lrcktx
+ &i2s1m0_sdi0
+ &i2s1m0_sdo0>;
+ rockchip,trcm-sync-tx-only;
+ status = "okay";
+};
+
+&mdio0 {
+ rgmii_phy0: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&mdio1 {
+ rgmii_phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pcie2x1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie20m1_pins>;
+ reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_sys2>;
+ status = "okay";
+};
+
+&pcie30phy {
+ status = "okay";
+};
+
+&pcie3x2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie30x2m1_pins>;
+ reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&pinctrl {
+ bluetooth {
+ bt_reg_on_h: bt-reg-on-h {
+ rockchip,pins = <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_wake_host_h: bt-wake-host-h {
+ rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ host_wake_bt_h: host-wake-bt-h {
+ rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ ir-receiver {
+ pwm3_ir: pwm3-ir {
+ rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ led: led {
+ rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ pcie_pwren_h: pcie-pwren-h {
+ rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie20 {
+ pcie20m1_pins: pcie20m1-pins {
+ rockchip,pins =
+ <2 RK_PD0 4 &pcfg_pull_none>,
+ <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>,
+ <2 RK_PD1 4 &pcfg_pull_none>;
+ };
+ };
+
+ pcie30x2 {
+ pcie30x2m1_pins: pcie30x2m1-pins {
+ rockchip,pins =
+ <2 RK_PD4 4 &pcfg_pull_none>,
+ <2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>,
+ <2 RK_PD5 4 &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ rtc {
+ rtcic_int_l: rtcic-int-l {
+ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb {
+ usb_host_pwren_h: usb-host-pwren-h {
+ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usb_otg_pwren_h: usb-otg-pwren-h {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ wifi_reg_on_h: wifi-reg-on-h {
+ rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wifi_wake_host_h: wifi-wake-host-h {
+ rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pmu_io_domains {
+ pmuio1-supply = <&vcc3v3_pmu>;
+ pmuio2-supply = <&vcc3v3_pmu>;
+ vccio1-supply = <&vccio_acodec>;
+ vccio2-supply = <&vcc_1v8>;
+ vccio3-supply = <&vccio_sd>;
+ vccio4-supply = <&vcc_1v8>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_1v8>;
+ vccio7-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ mmc-hs200-1_8v;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&sdmmc2 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_clk &sdmmc2m0_cmd>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sys2>;
+ vqmmc-supply = <&vcc_1v8>;
+ status = "disabled";
+};
+
+&sfc {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <104000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ };
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart8 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart8m0_xfer &uart8m0_ctsn &uart8m0_rtsn>;
+ uart-has-rtscts;
+ status = "disabled";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ extcon = <&usb2phy0>;
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy0_host {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&usb2phy0_otg {
+ phy-supply = <&vcc5v0_usb_otg>;
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb2phy1_otg {
+ phy-supply = <&vcc5v0_usb_host>;
+ status = "okay";
+};
+
+&vop {
+ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
--
2.45.2Hi Jonas, kernel test robot noticed the following build warnings: [auto build test WARNING on rockchip/for-next] [also build test WARNING on krzk/for-next krzk-dt/for-next krzk-mem-ctrl/for-next linus/master v6.10-rc5 next-20240627] [cannot apply to robh/for-next] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Jonas-Karlman/dt-bindings-arm-rockchip-Add-Radxa-ROCK-3B/20240627-160354 base: https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git for-next patch link: https://lore.kernel.org/r/20240626201502.1384123-3-jonas%40kwiboo.se patch subject: [PATCH v2 2/2] arm64: dts: rockchip: Add Radxa ROCK 3B config: arm64-randconfig-051-20240628 (https://download.01.org/0day-ci/archive/20240628/202406282157.SmRgaZOQ-lkp@intel.com/config) compiler: aarch64-linux-gcc (GCC) 13.2.0 dtschema version: 2024.6.dev3+g650bf2d reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240628/202406282157.SmRgaZOQ-lkp@intel.com/reproduce) If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags | Reported-by: kernel test robot <lkp@intel.com> | Closes: https://lore.kernel.org/oe-kbuild-all/202406282157.SmRgaZOQ-lkp@intel.com/ dtcheck warnings: (new ones prefixed by >>) >> arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml# -- 0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests/wiki
Hi Jonas, kernel test robot noticed the following build warnings: [auto build test WARNING on rockchip/for-next] [also build test WARNING on krzk/for-next krzk-dt/for-next krzk-mem-ctrl/for-next linus/master v6.10-rc5 next-20240627] [cannot apply to robh/for-next] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in https://git-scm.com/docs/git-format-patch#_base_tree_information] url: https://github.com/intel-lab-lkp/linux/commits/Jonas-Karlman/dt-bindings-arm-rockchip-Add-Radxa-ROCK-3B/20240627-160354 base: https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip.git for-next patch link: https://lore.kernel.org/r/20240626201502.1384123-3-jonas%40kwiboo.se patch subject: [PATCH v2 2/2] arm64: dts: rockchip: Add Radxa ROCK 3B config: arm64-randconfig-051-20240628 (https://download.01.org/0day-ci/archive/20240628/202406280948.sZf64ONz-lkp@intel.com/config) compiler: aarch64-linux-gcc (GCC) 13.2.0 dtschema version: 2024.6.dev2+g3b69bad reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20240628/202406280948.sZf64ONz-lkp@intel.com/reproduce) If you fix the issue in a separate patch/commit (i.e. not just a new version of the same patch/commit), kindly add following tags | Reported-by: kernel test robot <lkp@intel.com> | Closes: https://lore.kernel.org/oe-kbuild-all/202406280948.sZf64ONz-lkp@intel.com/ dtcheck warnings: (new ones prefixed by >>) >> arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dtb: pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks' do not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml# -- 0-DAY CI Kernel Test Service https://github.com/intel/lkp-tests/wiki
Hi,
thank you very much for your effort!
On 6/27/24 05:14, Jonas Karlman wrote:
> The Radxa ROCK 3B is a single-board computer based on the Pico-ITX form
> factor (100mm x 75mm). Two versions of the ROCK 3B exists, a community
> version based on the RK3568 SoC and an industrial version based on the
> RK3568J SoC.
>
> Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
>
> Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
> ---
> v2:
> - Use regulator-.* nodename for fixed regulators
> - Drop rockchip,mic-in-differential prop
> - Shorten Ethernet phy reset-deassert-us to 50 ms
> - Fix pcie pinctrl
> - Add keep-power-in-suspend to sdmmc2
>
> Following issue is reported by dtbs_check and is fixed by series at [1]:
>
> pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks'
> do not match any of the regexes: 'pinctrl-[0-9]+'
> from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
>
> [1] https://lore.kernel.org/all/20240622-rk809-fixes-v2-0-c0db420d3639@collabora.com/
> ---
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3568-rock-3b.dts | 780 ++++++++++++++++++
> 2 files changed, 781 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
>
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 90f5172f37e6..ae0ae02f51e9 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -114,6 +114,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3b.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
> new file mode 100644
> index 000000000000..46c959f1c6ad
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
> @@ -0,0 +1,780 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include "rk3568.dtsi"
> +
> +/ {
> + model = "Radxa ROCK 3B";
> + compatible = "radxa,rock-3b", "rockchip,rk3568";
> +
> + aliases {
> + ethernet0 = &gmac0;
> + ethernet1 = &gmac1;
> + mmc0 = &sdhci;
> + mmc1 = &sdmmc0;
> + mmc2 = &sdmmc2;
> + };
> +
> + chosen {
> + stdout-path = "serial2:1500000n8";
> + };
> +
> + hdmi-con {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> + };
> +
> + ir-receiver {
> + compatible = "gpio-ir-receiver";
> + gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm3_ir>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led-green {
led-0 or just led (leds-gpio.yaml)
Best regards,
--
FUKAUMI Naoki
Radxa Computer (Shenzhen) Co., Ltd.
> + color = <LED_COLOR_ID_GREEN>;
> + default-state = "on";
> + function = LED_FUNCTION_HEARTBEAT;
> + gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led>;
> + };
> + };
> +
> + /* pi6c pcie clock generator */
> + vcc3v3_pi6c_03: regulator-3v3-vcc-pi6c-03 {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_pwren_h>;
> + regulator-name = "vcc3v3_pi6c_03";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + startup-delay-us = <10000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc3v3_sys: regulator-3v3-vcc-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc3v3_sys2: regulator-3v3-vcc-sys2 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3_sys2";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc5v0_sys: regulator-5v0-vcc-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc5v0_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + vcc5v0_usb_host: regulator-5v0-vcc-usb-host {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_host_pwren_h>;
> + regulator-name = "vcc5v0_usb_host";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + vcc5v0_usb_otg: regulator-5v0-vcc-usb-otg {
> + compatible = "regulator-fixed";
> + enable-active-high;
> + gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_otg_pwren_h>;
> + regulator-name = "vcc5v0_usb_otg";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v0_sys>;
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk809 1>;
> + clock-names = "ext_clock";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_reg_on_h>;
> + post-power-on-delay-ms = <100>;
> + power-off-delay-us = <5000000>;
> + reset-gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_LOW>;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,name = "Analog RK809";
> + simple-audio-card,mclk-fs = <256>;
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s1_8ch>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&rk809>;
> + };
> + };
> +};
> +
> +&combphy0 {
> + status = "okay";
> +};
> +
> +&combphy1 {
> + status = "okay";
> +};
> +
> +&combphy2 {
> + status = "okay";
> +};
> +
> +&cpu0 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> + cpu-supply = <&vdd_cpu>;
> +};
> +
> +&gmac0 {
> + assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
> + assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
> + clock_in_out = "input";
> + phy-handle = <&rgmii_phy0>;
> + phy-mode = "rgmii-id";
> + phy-supply = <&vcc_3v3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&gmac0_miim
> + &gmac0_tx_bus2
> + &gmac0_rx_bus2
> + &gmac0_rgmii_clk
> + &gmac0_rgmii_bus
> + &gmac0_clkinout>;
> + status = "okay";
> +};
> +
> +&gmac1 {
> + assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
> + assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
> + clock_in_out = "input";
> + phy-handle = <&rgmii_phy1>;
> + phy-mode = "rgmii-id";
> + phy-supply = <&vcc_3v3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&gmac1m1_miim
> + &gmac1m1_tx_bus2
> + &gmac1m1_rx_bus2
> + &gmac1m1_rgmii_clk
> + &gmac1m1_rgmii_bus
> + &gmac1m1_clkinout>;
> + status = "okay";
> +};
> +
> +&gpu {
> + mali-supply = <&vdd_gpu>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + avdd-0v9-supply = <&vdda0v9_image>;
> + avdd-1v8-supply = <&vcca1v8_image>;
> + status = "okay";
> +};
> +
> +&hdmi_in {
> + hdmi_in_vp0: endpoint {
> + remote-endpoint = <&vp0_out_hdmi>;
> + };
> +};
> +
> +&hdmi_out {
> + hdmi_out_con: endpoint {
> + remote-endpoint = <&hdmi_con_in>;
> + };
> +};
> +
> +&hdmi_sound {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + vdd_cpu: regulator@1c {
> + compatible = "tcs,tcs4525";
> + reg = <0x1c>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-ramp-delay = <2300>;
> + vin-supply = <&vcc5v0_sys>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + rk809: pmic@20 {
> + compatible = "rockchip,rk809";
> + reg = <0x20>;
> + assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
> + assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
> + #clock-cells = <1>;
> + clocks = <&cru I2S1_MCLKOUT_TX>;
> + clock-names = "mclk";
> + clock-output-names = "rk809-clkout1", "rk809-clkout2";
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>;
> + #sound-dai-cells = <0>;
> + system-power-controller;
> + wakeup-source;
> +
> + vcc1-supply = <&vcc3v3_sys>;
> + vcc2-supply = <&vcc3v3_sys>;
> + vcc3-supply = <&vcc3v3_sys>;
> + vcc4-supply = <&vcc3v3_sys>;
> + vcc5-supply = <&vcc3v3_sys>;
> + vcc6-supply = <&vcc3v3_sys>;
> + vcc7-supply = <&vcc3v3_sys>;
> + vcc8-supply = <&vcc3v3_sys>;
> + vcc9-supply = <&vcc3v3_sys>;
> +
> + regulators {
> + vdd_logic: DCDC_REG1 {
> + regulator-name = "vdd_logic";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-mode = <0x2>;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu: DCDC_REG2 {
> + regulator-name = "vdd_gpu";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-mode = <0x2>;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_ddr: DCDC_REG3 {
> + regulator-name = "vcc_ddr";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-initial-mode = <0x2>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vdd_npu: DCDC_REG4 {
> + regulator-name = "vdd_npu";
> + regulator-initial-mode = <0x2>;
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <6001>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_1v8: DCDC_REG5 {
> + regulator-name = "vcc_1v8";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdda0v9_image: LDO_REG1 {
> + regulator-name = "vdda0v9_image";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdda_0v9: LDO_REG2 {
> + regulator-name = "vdda_0v9";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdda0v9_pmu: LDO_REG3 {
> + regulator-name = "vdda0v9_pmu";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <900000>;
> + };
> + };
> +
> + vccio_acodec: LDO_REG4 {
> + regulator-name = "vccio_acodec";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd: LDO_REG5 {
> + regulator-name = "vccio_sd";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_pmu: LDO_REG6 {
> + regulator-name = "vcc3v3_pmu";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <3300000>;
> + };
> + };
> +
> + vcca_1v8: LDO_REG7 {
> + regulator-name = "vcca_1v8";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcca1v8_pmu: LDO_REG8 {
> + regulator-name = "vcca1v8_pmu";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcca1v8_image: LDO_REG9 {
> + regulator-name = "vcca1v8_image";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_3v3: SWITCH_REG1 {
> + regulator-name = "vcc_3v3";
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc3v3_sd: SWITCH_REG2 {
> + regulator-name = "vcc3v3_sd";
> + regulator-always-on;
> + regulator-boot-on;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> +
> + hym8563: rtc@51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + interrupt-parent = <&gpio0>;
> + interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
> + #clock-cells = <0>;
> + clock-output-names = "rtcic_32kout";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rtcic_int_l>;
> + wakeup-source;
> + };
> +};
> +
> +&i2s0_8ch {
> + status = "okay";
> +};
> +
> +&i2s1_8ch {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2s1m0_sclktx
> + &i2s1m0_lrcktx
> + &i2s1m0_sdi0
> + &i2s1m0_sdo0>;
> + rockchip,trcm-sync-tx-only;
> + status = "okay";
> +};
> +
> +&mdio0 {
> + rgmii_phy0: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + reset-assert-us = <20000>;
> + reset-deassert-us = <50000>;
> + reset-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&mdio1 {
> + rgmii_phy1: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + reset-assert-us = <20000>;
> + reset-deassert-us = <50000>;
> + reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&pcie2x1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie20m1_pins>;
> + reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
> + vpcie3v3-supply = <&vcc3v3_sys2>;
> + status = "okay";
> +};
> +
> +&pcie30phy {
> + status = "okay";
> +};
> +
> +&pcie3x2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie30x2m1_pins>;
> + reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + bluetooth {
> + bt_reg_on_h: bt-reg-on-h {
> + rockchip,pins = <4 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + bt_wake_host_h: bt-wake-host-h {
> + rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + host_wake_bt_h: host-wake-bt-h {
> + rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + ir-receiver {
> + pwm3_ir: pwm3-ir {
> + rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + leds {
> + led: led {
> + rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pcie {
> + pcie_pwren_h: pcie-pwren-h {
> + rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + pcie20 {
> + pcie20m1_pins: pcie20m1-pins {
> + rockchip,pins =
> + <2 RK_PD0 4 &pcfg_pull_none>,
> + <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>,
> + <2 RK_PD1 4 &pcfg_pull_none>;
> + };
> + };
> +
> + pcie30x2 {
> + pcie30x2m1_pins: pcie30x2m1-pins {
> + rockchip,pins =
> + <2 RK_PD4 4 &pcfg_pull_none>,
> + <2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>,
> + <2 RK_PD5 4 &pcfg_pull_none>;
> + };
> + };
> +
> + pmic {
> + pmic_int_l: pmic-int-l {
> + rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + rtc {
> + rtcic_int_l: rtcic-int-l {
> + rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
> + };
> + };
> +
> + usb {
> + usb_host_pwren_h: usb-host-pwren-h {
> + rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + usb_otg_pwren_h: usb-otg-pwren-h {
> + rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + wifi {
> + wifi_reg_on_h: wifi-reg-on-h {
> + rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + wifi_wake_host_h: wifi-wake-host-h {
> + rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&pmu_io_domains {
> + pmuio1-supply = <&vcc3v3_pmu>;
> + pmuio2-supply = <&vcc3v3_pmu>;
> + vccio1-supply = <&vccio_acodec>;
> + vccio2-supply = <&vcc_1v8>;
> + vccio3-supply = <&vccio_sd>;
> + vccio4-supply = <&vcc_1v8>;
> + vccio5-supply = <&vcc_3v3>;
> + vccio6-supply = <&vcc_1v8>;
> + vccio7-supply = <&vcc_3v3>;
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vcca_1v8>;
> + status = "okay";
> +};
> +
> +&sdhci {
> + bus-width = <8>;
> + max-frequency = <200000000>;
> + mmc-hs200-1_8v;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
> + vmmc-supply = <&vcc_3v3>;
> + vqmmc-supply = <&vcc_1v8>;
> + status = "okay";
> +};
> +
> +&sdmmc0 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + disable-wp;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
> + vmmc-supply = <&vcc3v3_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + keep-power-in-suspend;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_clk &sdmmc2m0_cmd>;
> + sd-uhs-sdr104;
> + vmmc-supply = <&vcc3v3_sys2>;
> + vqmmc-supply = <&vcc_1v8>;
> + status = "disabled";
> +};
> +
> +&sfc {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <104000000>;
> + spi-rx-bus-width = <4>;
> + spi-tx-bus-width = <1>;
> + };
> +};
> +
> +&tsadc {
> + rockchip,hw-tshut-mode = <1>;
> + rockchip,hw-tshut-polarity = <0>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart8 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart8m0_xfer &uart8m0_ctsn &uart8m0_rtsn>;
> + uart-has-rtscts;
> + status = "disabled";
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_host0_ohci {
> + status = "okay";
> +};
> +
> +&usb_host0_xhci {
> + extcon = <&usb2phy0>;
> + status = "okay";
> +};
> +
> +&usb_host1_xhci {
> + status = "okay";
> +};
> +
> +&usb2phy0 {
> + status = "okay";
> +};
> +
> +&usb2phy0_host {
> + phy-supply = <&vcc5v0_usb_host>;
> + status = "okay";
> +};
> +
> +&usb2phy0_otg {
> + phy-supply = <&vcc5v0_usb_otg>;
> + status = "okay";
> +};
> +
> +&usb2phy1 {
> + status = "okay";
> +};
> +
> +&usb2phy1_otg {
> + phy-supply = <&vcc5v0_usb_host>;
> + status = "okay";
> +};
> +
> +&vop {
> + assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
> + assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
> + status = "okay";
> +};
> +
> +&vop_mmu {
> + status = "okay";
> +};
> +
> +&vp0 {
> + vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
> + reg = <ROCKCHIP_VOP2_EP_HDMI0>;
> + remote-endpoint = <&hdmi_in_vp0>;
> + };
> +};
Am 27.06.24 um 00:29 schrieb FUKAUMI Naoki:
> Hi,
>
> thank you very much for your effort!
>
> On 6/27/24 05:14, Jonas Karlman wrote:
>> The Radxa ROCK 3B is a single-board computer based on the Pico-ITX form
>> factor (100mm x 75mm). Two versions of the ROCK 3B exists, a community
>> version based on the RK3568 SoC and an industrial version based on the
>> RK3568J SoC.
>>
>> Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
>>
>> Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
>> ---
>> v2:
>> - Use regulator-.* nodename for fixed regulators
>> - Drop rockchip,mic-in-differential prop
>> - Shorten Ethernet phy reset-deassert-us to 50 ms
>> - Fix pcie pinctrl
>> - Add keep-power-in-suspend to sdmmc2
>>
>> Following issue is reported by dtbs_check and is fixed by series at [1]:
>>
>> pmic@20: '#sound-dai-cells', 'assigned-clock-parents',
>> 'assigned-clocks', 'clock-names', 'clocks'
>> do not match any of the regexes: 'pinctrl-[0-9]+'
>> from schema $id:
>> http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
>>
>> [1]
>> https://lore.kernel.org/all/20240622-rk809-fixes-v2-0-c0db420d3639@collabora.com/
>> ---
>> arch/arm64/boot/dts/rockchip/Makefile | 1 +
>> .../boot/dts/rockchip/rk3568-rock-3b.dts | 780 ++++++++++++++++++
>> 2 files changed, 781 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/Makefile
>> b/arch/arm64/boot/dts/rockchip/Makefile
>> index 90f5172f37e6..ae0ae02f51e9 100644
>> --- a/arch/arm64/boot/dts/rockchip/Makefile
>> +++ b/arch/arm64/boot/dts/rockchip/Makefile
>> @@ -114,6 +114,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
>> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3b.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
>> b/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
>> new file mode 100644
>> index 000000000000..46c959f1c6ad
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
>> @@ -0,0 +1,780 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/leds/common.h>
>> +#include <dt-bindings/pinctrl/rockchip.h>
>> +#include <dt-bindings/soc/rockchip,vop2.h>
>> +#include "rk3568.dtsi"
>> +
>> +/ {
>> + model = "Radxa ROCK 3B";
>> + compatible = "radxa,rock-3b", "rockchip,rk3568";
>> +
>> + aliases {
>> + ethernet0 = &gmac0;
>> + ethernet1 = &gmac1;
>> + mmc0 = &sdhci;
>> + mmc1 = &sdmmc0;
>> + mmc2 = &sdmmc2;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial2:1500000n8";
>> + };
>> +
>> + hdmi-con {
>> + compatible = "hdmi-connector";
>> + type = "a";
>> +
>> + port {
>> + hdmi_con_in: endpoint {
>> + remote-endpoint = <&hdmi_out_con>;
>> + };
>> + };
>> + };
>> +
>> + ir-receiver {
>> + compatible = "gpio-ir-receiver";
>> + gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_LOW>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pwm3_ir>;
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + led-green {
>
> led-0 or just led (leds-gpio.yaml)
>
That's a misinterpretation of the pattern-properties regex: The
"non-preferred" part of the regex does neither have a "^" nor an "$", thus
it allows all nodes names which have "led" somewhere.
> Best regards,
>
> --
> FUKAUMI Naoki
Hi,
On 2024-06-27 00:29, FUKAUMI Naoki wrote:
> Hi,
>
> thank you very much for your effort!
>
> On 6/27/24 05:14, Jonas Karlman wrote:
>> The Radxa ROCK 3B is a single-board computer based on the Pico-ITX form
>> factor (100mm x 75mm). Two versions of the ROCK 3B exists, a community
>> version based on the RK3568 SoC and an industrial version based on the
>> RK3568J SoC.
>>
>> Add initial support for eMMC, SD-card, Ethernet, HDMI, PCIe and USB.
>>
>> Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
>> ---
>> v2:
>> - Use regulator-.* nodename for fixed regulators
>> - Drop rockchip,mic-in-differential prop
>> - Shorten Ethernet phy reset-deassert-us to 50 ms
>> - Fix pcie pinctrl
>> - Add keep-power-in-suspend to sdmmc2
>>
>> Following issue is reported by dtbs_check and is fixed by series at [1]:
>>
>> pmic@20: '#sound-dai-cells', 'assigned-clock-parents', 'assigned-clocks', 'clock-names', 'clocks'
>> do not match any of the regexes: 'pinctrl-[0-9]+'
>> from schema $id: http://devicetree.org/schemas/mfd/rockchip,rk809.yaml#
>>
>> [1] https://lore.kernel.org/all/20240622-rk809-fixes-v2-0-c0db420d3639@collabora.com/
>> ---
>> arch/arm64/boot/dts/rockchip/Makefile | 1 +
>> .../boot/dts/rockchip/rk3568-rock-3b.dts | 780 ++++++++++++++++++
>> 2 files changed, 781 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
>>
>> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
>> index 90f5172f37e6..ae0ae02f51e9 100644
>> --- a/arch/arm64/boot/dts/rockchip/Makefile
>> +++ b/arch/arm64/boot/dts/rockchip/Makefile
>> @@ -114,6 +114,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
>> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3b.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5.dtb
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
>> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
>> new file mode 100644
>> index 000000000000..46c959f1c6ad
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3b.dts
>> @@ -0,0 +1,780 @@
>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/leds/common.h>
>> +#include <dt-bindings/pinctrl/rockchip.h>
>> +#include <dt-bindings/soc/rockchip,vop2.h>
>> +#include "rk3568.dtsi"
>> +
>> +/ {
>> + model = "Radxa ROCK 3B";
>> + compatible = "radxa,rock-3b", "rockchip,rk3568";
>> +
>> + aliases {
>> + ethernet0 = &gmac0;
>> + ethernet1 = &gmac1;
>> + mmc0 = &sdhci;
>> + mmc1 = &sdmmc0;
>> + mmc2 = &sdmmc2;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial2:1500000n8";
>> + };
>> +
>> + hdmi-con {
>> + compatible = "hdmi-connector";
>> + type = "a";
>> +
>> + port {
>> + hdmi_con_in: endpoint {
>> + remote-endpoint = <&hdmi_out_con>;
>> + };
>> + };
>> + };
>> +
>> + ir-receiver {
>> + compatible = "gpio-ir-receiver";
>> + gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_LOW>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pwm3_ir>;
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + led-green {
>
> led-0 or just led (leds-gpio.yaml)
Thanks, I will fix in v3.
Regards,
Jonas
>
> Best regards,
>
> --
> FUKAUMI Naoki
> Radxa Computer (Shenzhen) Co., Ltd.
>
[snip]
© 2016 - 2025 Red Hat, Inc.