Add the WKUP ESM instance for J721E. It has three instances in total,
one in the MAIN domain (main_esm) and two in the MCU-WKUP domain
(mcu_esm and wkup_esm).

Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 4618b697fbc4..b0f41e9829cc 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -689,4 +689,9 @@ mcu_esm: esm@40800000 {
 		ti,esm-pins = <95>;
 		bootph-pre-ram;
 	};
+
+	wkup_esm: esm@42080000 {
+		compatible = "ti,j721e-esm";
+		reg = <0x00 0x42080000 0x00 0x1000>;
+	};
 };
-- 
2.34.1

Hi Neha

On 3/26/2024 5:57 PM, Neha Malcom Francis wrote:
> Add the WKUP ESM instance for J721E. It has three instances in total,
> one in the MAIN domain (main_esm) and two in the MCU-WKUP domain
> (mcu_esm and wkup_esm).
>
> Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
> ---
>   arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 5 +++++
>   1 file changed, 5 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> index 4618b697fbc4..b0f41e9829cc 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> @@ -689,4 +689,9 @@ mcu_esm: esm@40800000 {
>   		ti,esm-pins = <95>;
>   		bootph-pre-ram;
>   	};
> +
> +	wkup_esm: esm@42080000 {
> +		compatible = "ti,j721e-esm";
> +		reg = <0x00 0x42080000 0x00 0x1000>;

I think , only  esm@40800000 should be good for this SOC.

I am not sure, why you want to add this. If you still want to add this 
for completeness ,

then two options, I suggest

1) If you plan to use this mention bootph-pre-ram and ti,esm-pins

2) In case , no plan to use this then please mark node as disabled


> +	};
>   };

Hi Udit,

On 10/04/24 10:42, Kumar, Udit wrote:
> Hi Neha
> 
> On 3/26/2024 5:57 PM, Neha Malcom Francis wrote:
>> Add the WKUP ESM instance for J721E. It has three instances in total,
>> one in the MAIN domain (main_esm) and two in the MCU-WKUP domain
>> (mcu_esm and wkup_esm).
>>
>> Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
>> ---
>>   arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 5 +++++
>>   1 file changed, 5 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi 
>> b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
>> index 4618b697fbc4..b0f41e9829cc 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
>> @@ -689,4 +689,9 @@ mcu_esm: esm@40800000 {
>>           ti,esm-pins = <95>;
>>           bootph-pre-ram;
>>       };
>> +
>> +    wkup_esm: esm@42080000 {
>> +        compatible = "ti,j721e-esm";
>> +        reg = <0x00 0x42080000 0x00 0x1000>;
> 
> I think , only  esm@40800000 should be good for this SOC.
> 
> I am not sure, why you want to add this. If you still want to add this for 
> completeness ,

Yes, I wanted to make sure all ESM modules are present for DTS completeness.
> 
> then two options, I suggest
> 
> 1) If you plan to use this mention bootph-pre-ram and ti,esm-pins
> 

No plans for using it as of now.

J721E ESM interrupt routing is such that the MAIN_ESM interrupt triggers an 
error event in the MCU_ESM (which is correctly set via their node ti,j721e-esm 
glue logic pins). The MCU_ESM and WKUP_ESM both generate the same interrupt 
after. So there is no ti,j721e-esm pin applicable for WKUP_ESM.

> 2) In case , no plan to use this then please mark node as disabled
> 

Yes I will mark this as disabled, I overlooked the fact that leaving this 
enabled would throw "ESM init failed" when DT syncs with U-Boot. Thanks for 
catching!

> 
>> +    };
>>   };

-- 
Thanking You
Neha Malcom Francis