1. Patchew
  2. linux
  3. [PATCH net-next v1 0/4] net: stmmac: Enable Per DMA Channel interrupt
  4. View patch

[PATCH net-next v1 4/4] net: stmmac: Use interrupt mode INTM=1 for per channel irq

Leong Ching Swee posted 4 patches 1 year, 12 months ago
There is a newer version of this series
[PATCH net-next v1 4/4] net: stmmac: Use interrupt mode INTM=1 for per channel irq
Posted by Leong Ching Swee 1 year, 12 months ago 
From: Swee Leong Ching <leong.ching.swee@intel.com>

Enable per DMA channel interrupt that uses shared peripheral
interrupt (SPI), so only per channel TX and RX intr (TI/RI)
are handled by TX/RX ISR without calling common interrupt ISR.

Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com>
Signed-off-by: Swee Leong Ching <leong.ching.swee@intel.com>
---
 .../net/ethernet/stmicro/stmmac/dwxgmac2.h    |  3 ++
 .../ethernet/stmicro/stmmac/dwxgmac2_dma.c    | 32 +++++++++++--------
 2 files changed, 22 insertions(+), 13 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
index 207ff1799f2c..04bf731cb7ea 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
+++ b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
@@ -346,6 +346,9 @@
 /* DMA Registers */
 #define XGMAC_DMA_MODE			0x00003000
 #define XGMAC_SWR			BIT(0)
+#define XGMAC_DMA_MODE_INTM_MASK	GENMASK(13, 12)
+#define XGMAC_DMA_MODE_INTM_SHIFT	12
+#define XGMAC_DMA_MODE_INTM_MODE1	0x1
 #define XGMAC_DMA_SYSBUS_MODE		0x00003004
 #define XGMAC_WR_OSR_LMT		GENMASK(29, 24)
 #define XGMAC_WR_OSR_LMT_SHIFT		24
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
index 3cde695fec91..dcb9f094415d 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
@@ -31,6 +31,13 @@ static void dwxgmac2_dma_init(void __iomem *ioaddr,
 		value |= XGMAC_EAME;
 
 	writel(value, ioaddr + XGMAC_DMA_SYSBUS_MODE);
+
+	if (dma_cfg->multi_irq_en) {
+		value = readl(ioaddr + XGMAC_DMA_MODE);
+		value &= ~XGMAC_DMA_MODE_INTM_MASK;
+		value |= (XGMAC_DMA_MODE_INTM_MODE1 << XGMAC_DMA_MODE_INTM_SHIFT);
+		writel(value, ioaddr + XGMAC_DMA_MODE);
+	}
 }
 
 static void dwxgmac2_dma_init_chan(struct stmmac_priv *priv,
@@ -365,19 +372,18 @@ static int dwxgmac2_dma_interrupt(struct stmmac_priv *priv,
 	}
 
 	/* TX/RX NORMAL interrupts */
-	if (likely(intr_status & XGMAC_NIS)) {
-		if (likely(intr_status & XGMAC_RI)) {
-			u64_stats_update_begin(&rxq_stats->syncp);
-			rxq_stats->rx_normal_irq_n++;
-			u64_stats_update_end(&rxq_stats->syncp);
-			ret |= handle_rx;
-		}
-		if (likely(intr_status & (XGMAC_TI | XGMAC_TBU))) {
-			u64_stats_update_begin(&txq_stats->syncp);
-			txq_stats->tx_normal_irq_n++;
-			u64_stats_update_end(&txq_stats->syncp);
-			ret |= handle_tx;
-		}
+	if (likely(intr_status & XGMAC_RI)) {
+		u64_stats_update_begin(&rxq_stats->syncp);
+		rxq_stats->rx_normal_irq_n++;
+		u64_stats_update_end(&rxq_stats->syncp);
+		ret |= handle_rx;
+	}
+
+	if (likely(intr_status & (XGMAC_TI | XGMAC_TBU))) {
+		u64_stats_update_begin(&txq_stats->syncp);
+		txq_stats->tx_normal_irq_n++;
+		u64_stats_update_end(&txq_stats->syncp);
+		ret |= handle_tx;
 	}
 
 	/* Clear interrupts */
-- 
2.34.1
Re: [PATCH net-next v1 4/4] net: stmmac: Use interrupt mode INTM=1 for per channel irq
Posted by Serge Semin 1 year, 12 months ago 
On Fri, Dec 22, 2023 at 01:44:51PM +0800, Leong Ching Swee wrote:
> From: Swee Leong Ching <leong.ching.swee@intel.com>
> 
> Enable per DMA channel interrupt that uses shared peripheral
> interrupt (SPI), so only per channel TX and RX intr (TI/RI)
> are handled by TX/RX ISR without calling common interrupt ISR.
> 
> Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com>
> Signed-off-by: Swee Leong Ching <leong.ching.swee@intel.com>
> ---
>  .../net/ethernet/stmicro/stmmac/dwxgmac2.h    |  3 ++
>  .../ethernet/stmicro/stmmac/dwxgmac2_dma.c    | 32 +++++++++++--------
>  2 files changed, 22 insertions(+), 13 deletions(-)
> 
> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
> index 207ff1799f2c..04bf731cb7ea 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
> +++ b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
> @@ -346,6 +346,9 @@
>  /* DMA Registers */
>  #define XGMAC_DMA_MODE			0x00003000
>  #define XGMAC_SWR			BIT(0)
> +#define XGMAC_DMA_MODE_INTM_MASK	GENMASK(13, 12)
> +#define XGMAC_DMA_MODE_INTM_SHIFT	12
> +#define XGMAC_DMA_MODE_INTM_MODE1	0x1
>  #define XGMAC_DMA_SYSBUS_MODE		0x00003004
>  #define XGMAC_WR_OSR_LMT		GENMASK(29, 24)
>  #define XGMAC_WR_OSR_LMT_SHIFT		24
> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
> index 3cde695fec91..dcb9f094415d 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
> @@ -31,6 +31,13 @@ static void dwxgmac2_dma_init(void __iomem *ioaddr,
>  		value |= XGMAC_EAME;
>  
>  	writel(value, ioaddr + XGMAC_DMA_SYSBUS_MODE);
> +
> +	if (dma_cfg->multi_irq_en) {
> +		value = readl(ioaddr + XGMAC_DMA_MODE);
> +		value &= ~XGMAC_DMA_MODE_INTM_MASK;
> +		value |= (XGMAC_DMA_MODE_INTM_MODE1 << XGMAC_DMA_MODE_INTM_SHIFT);
> +		writel(value, ioaddr + XGMAC_DMA_MODE);
> +	}
>  }
>  
>  static void dwxgmac2_dma_init_chan(struct stmmac_priv *priv,
> @@ -365,19 +372,18 @@ static int dwxgmac2_dma_interrupt(struct stmmac_priv *priv,
>  	}
>  

>  	/* TX/RX NORMAL interrupts */
> -	if (likely(intr_status & XGMAC_NIS)) {
> -		if (likely(intr_status & XGMAC_RI)) {
> -			u64_stats_update_begin(&rxq_stats->syncp);
> -			rxq_stats->rx_normal_irq_n++;
> -			u64_stats_update_end(&rxq_stats->syncp);
> -			ret |= handle_rx;
> -		}
> -		if (likely(intr_status & (XGMAC_TI | XGMAC_TBU))) {
> -			u64_stats_update_begin(&txq_stats->syncp);
> -			txq_stats->tx_normal_irq_n++;
> -			u64_stats_update_end(&txq_stats->syncp);
> -			ret |= handle_tx;
> -		}
> +	if (likely(intr_status & XGMAC_RI)) {
> +		u64_stats_update_begin(&rxq_stats->syncp);
> +		rxq_stats->rx_normal_irq_n++;
> +		u64_stats_update_end(&rxq_stats->syncp);
> +		ret |= handle_rx;
> +	}
> +
> +	if (likely(intr_status & (XGMAC_TI | XGMAC_TBU))) {
> +		u64_stats_update_begin(&txq_stats->syncp);
> +		txq_stats->tx_normal_irq_n++;
> +		u64_stats_update_end(&txq_stats->syncp);
> +		ret |= handle_tx;

Could you please clarify my comment to the original patch:

On Fri, Aug 18, 2023 at 20:10:21PM +0300, Serge Semin wrote:
> Just curious. Is this change really necessary seeing NIS IRQ is
> unmasked and it is unmasked-OR of the RI/TI/TBU flags in the
> DMA_CHx_Status register? Moreover based on the HW manual,
> DMA_CHx_Status reflects raw IRQ flags status except NIS and AIS which
> are the masked OR of the respective flags. So AFAIU NIS will be set in
> anyway if you have RI/TI/TBU IRQs enabled.

-Serge(y)

>  	}
>  
>  	/* Clear interrupts */
> -- 
> 2.34.1
> 
>
RE: [PATCH net-next v1 4/4] net: stmmac: Use interrupt mode INTM=1 for per channel irq
Posted by Swee, Leong Ching 1 year, 11 months ago 
> -----Original Message-----
> From: Serge Semin <fancer.lancer@gmail.com>
> Sent: Saturday, December 23, 2023 5:57 AM
> To: Swee, Leong Ching <leong.ching.swee@intel.com>
> Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>; Alexandre Torgue
> <alexandre.torgue@foss.st.com>; Jose Abreu <joabreu@synopsys.com>;
> David S . Miller <davem@davemloft.net>; Eric Dumazet
> <edumazet@google.com>; Jakub Kicinski <kuba@kernel.org>; Paolo Abeni
> <pabeni@redhat.com>; Rob Herring <robh+dt@kernel.org>; Krzysztof
> Kozlowski <krzysztof.kozlowski+dt@linaro.org>; Conor Dooley
> <conor+dt@kernel.org>; Giuseppe Cavallaro <peppe.cavallaro@st.com>;
> linux-stm32@st-md-mailman.stormreply.com; linux-arm-
> kernel@lists.infradead.org; linux-kernel@vger.kernel.org;
> netdev@vger.kernel.org; devicetree@vger.kernel.org; Teoh Ji Sheng
> <ji.sheng.teoh@intel.com>
> Subject: Re: [PATCH net-next v1 4/4] net: stmmac: Use interrupt mode
> INTM=1 for per channel irq
> 
> On Fri, Dec 22, 2023 at 01:44:51PM +0800, Leong Ching Swee wrote:
> > From: Swee Leong Ching <leong.ching.swee@intel.com>
> >
> > Enable per DMA channel interrupt that uses shared peripheral interrupt
> > (SPI), so only per channel TX and RX intr (TI/RI) are handled by TX/RX
> > ISR without calling common interrupt ISR.
> >
> > Signed-off-by: Teoh Ji Sheng <ji.sheng.teoh@intel.com>
> > Signed-off-by: Swee Leong Ching <leong.ching.swee@intel.com>
> > ---
> >  .../net/ethernet/stmicro/stmmac/dwxgmac2.h    |  3 ++
> >  .../ethernet/stmicro/stmmac/dwxgmac2_dma.c    | 32 +++++++++++-------
> -
> >  2 files changed, 22 insertions(+), 13 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
> > b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
> > index 207ff1799f2c..04bf731cb7ea 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
> > +++ b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2.h
> > @@ -346,6 +346,9 @@
> >  /* DMA Registers */
> >  #define XGMAC_DMA_MODE			0x00003000
> >  #define XGMAC_SWR			BIT(0)
> > +#define XGMAC_DMA_MODE_INTM_MASK	GENMASK(13, 12)
> > +#define XGMAC_DMA_MODE_INTM_SHIFT	12
> > +#define XGMAC_DMA_MODE_INTM_MODE1	0x1
> >  #define XGMAC_DMA_SYSBUS_MODE		0x00003004
> >  #define XGMAC_WR_OSR_LMT		GENMASK(29, 24)
> >  #define XGMAC_WR_OSR_LMT_SHIFT		24
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
> > b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
> > index 3cde695fec91..dcb9f094415d 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
> > +++ b/drivers/net/ethernet/stmicro/stmmac/dwxgmac2_dma.c
> > @@ -31,6 +31,13 @@ static void dwxgmac2_dma_init(void __iomem
> *ioaddr,
> >  		value |= XGMAC_EAME;
> >
> >  	writel(value, ioaddr + XGMAC_DMA_SYSBUS_MODE);
> > +
> > +	if (dma_cfg->multi_irq_en) {
> > +		value = readl(ioaddr + XGMAC_DMA_MODE);
> > +		value &= ~XGMAC_DMA_MODE_INTM_MASK;
> > +		value |= (XGMAC_DMA_MODE_INTM_MODE1 <<
> XGMAC_DMA_MODE_INTM_SHIFT);
> > +		writel(value, ioaddr + XGMAC_DMA_MODE);
> > +	}
> >  }
> >
> >  static void dwxgmac2_dma_init_chan(struct stmmac_priv *priv, @@
> > -365,19 +372,18 @@ static int dwxgmac2_dma_interrupt(struct
> stmmac_priv *priv,
> >  	}
> >
> 
> >  	/* TX/RX NORMAL interrupts */
> > -	if (likely(intr_status & XGMAC_NIS)) {
> > -		if (likely(intr_status & XGMAC_RI)) {
> > -			u64_stats_update_begin(&rxq_stats->syncp);
> > -			rxq_stats->rx_normal_irq_n++;
> > -			u64_stats_update_end(&rxq_stats->syncp);
> > -			ret |= handle_rx;
> > -		}
> > -		if (likely(intr_status & (XGMAC_TI | XGMAC_TBU))) {
> > -			u64_stats_update_begin(&txq_stats->syncp);
> > -			txq_stats->tx_normal_irq_n++;
> > -			u64_stats_update_end(&txq_stats->syncp);
> > -			ret |= handle_tx;
> > -		}
> > +	if (likely(intr_status & XGMAC_RI)) {
> > +		u64_stats_update_begin(&rxq_stats->syncp);
> > +		rxq_stats->rx_normal_irq_n++;
> > +		u64_stats_update_end(&rxq_stats->syncp);
> > +		ret |= handle_rx;
> > +	}
> > +
> > +	if (likely(intr_status & (XGMAC_TI | XGMAC_TBU))) {
> > +		u64_stats_update_begin(&txq_stats->syncp);
> > +		txq_stats->tx_normal_irq_n++;
> > +		u64_stats_update_end(&txq_stats->syncp);
> > +		ret |= handle_tx;
> 
> Could you please clarify my comment to the original patch:
> 
> On Fri, Aug 18, 2023 at 20:10:21PM +0300, Serge Semin wrote:
> > Just curious. Is this change really necessary seeing NIS IRQ is
> > unmasked and it is unmasked-OR of the RI/TI/TBU flags in the
> > DMA_CHx_Status register? Moreover based on the HW manual,
> > DMA_CHx_Status reflects raw IRQ flags status except NIS and AIS which
> > are the masked OR of the respective flags. So AFAIU NIS will be set in
> > anyway if you have RI/TI/TBU IRQs enabled.
> 
> -Serge(y)
> 
Thanks for your comment. 
From my test, NIS bit value is 0 once INTM is set, even with RI/TI flags value is 1. 
This might be the reason why previous patch set had this change.
-Jim
> >  	}
> >
> >  	/* Clear interrupts */
> > --
> > 2.34.1
> >
> >

Patchew 2.1-devel-b67e4c2

© 2016 - 2025 Red Hat, Inc.