In order to support half-duplex operation at 10M and 100M link speeds, the
PHY collision detection signal (COL) should be routed to ICSSG
GPIO pin (PRGx_PRU0/1_GPI10) so that firmware can detect collision signal
and apply the CSMA/CD algorithm applicable for half duplex operation. A DT
property, "ti,half-duplex-capable" is introduced for this purpose. If
board has PHY COL pin conencted to PRGx_PRU1_GPIO10, this DT property can
be added to eth node of ICSSG, MII port to support half duplex operation at
that port.

Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
---
 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
index 836d2d60e87d..229c8f32019f 100644
--- a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
+++ b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
@@ -107,6 +107,13 @@ properties:
               phandle to system controller node and register offset
               to ICSSG control register for RGMII transmit delay
 
+          ti,half-duplex-capable:
+            type: boolean
+            description:
+              Indicates that the PHY output pin COL is routed to ICSSG GPIO pin
+              (PRGx_PRU0/1_GPIO10) as input so that the ICSSG MII port is
+              capable of half duplex operations.
+
         required:
           - reg
     anyOf:
-- 
2.34.1

On Wed, 13 Sep 2023 14:40:10 +0530, MD Danish Anwar wrote:
> In order to support half-duplex operation at 10M and 100M link speeds, the
> PHY collision detection signal (COL) should be routed to ICSSG
> GPIO pin (PRGx_PRU0/1_GPI10) so that firmware can detect collision signal
> and apply the CSMA/CD algorithm applicable for half duplex operation. A DT
> property, "ti,half-duplex-capable" is introduced for this purpose. If
> board has PHY COL pin conencted to PRGx_PRU1_GPIO10, this DT property can
> be added to eth node of ICSSG, MII port to support half duplex operation at
> that port.
> 
> Reviewed-by: Roger Quadros <rogerq@kernel.org>
> Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
> ---
>  Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml | 7 +++++++
>  1 file changed, 7 insertions(+)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

On Wed, Sep 13, 2023 at 02:40:10PM +0530, MD Danish Anwar wrote:
> In order to support half-duplex operation at 10M and 100M link speeds, the
> PHY collision detection signal (COL) should be routed to ICSSG
> GPIO pin (PRGx_PRU0/1_GPI10) so that firmware can detect collision signal
> and apply the CSMA/CD algorithm applicable for half duplex operation. A DT
> property, "ti,half-duplex-capable" is introduced for this purpose. If
> board has PHY COL pin conencted to PRGx_PRU1_GPIO10, this DT property can
> be added to eth node of ICSSG, MII port to support half duplex operation at
> that port.
> 
> Reviewed-by: Roger Quadros <rogerq@kernel.org>
> Signed-off-by: MD Danish Anwar <danishanwar@ti.com>

Acked-by: Conor Dooley <conor.dooley@microchip.com>

Thanks,
Conor.

> ---
>  Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
> index 836d2d60e87d..229c8f32019f 100644
> --- a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
> +++ b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
> @@ -107,6 +107,13 @@ properties:
>                phandle to system controller node and register offset
>                to ICSSG control register for RGMII transmit delay
>  
> +          ti,half-duplex-capable:
> +            type: boolean
> +            description:
> +              Indicates that the PHY output pin COL is routed to ICSSG GPIO pin
> +              (PRGx_PRU0/1_GPIO10) as input so that the ICSSG MII port is
> +              capable of half duplex operations.
> +
>          required:
>            - reg
>      anyOf:
> -- 
> 2.34.1
> 

On Wed, Sep 13, 2023 at 02:40:10PM +0530, MD Danish Anwar wrote:
> In order to support half-duplex operation at 10M and 100M link speeds, the
> PHY collision detection signal (COL) should be routed to ICSSG
> GPIO pin (PRGx_PRU0/1_GPI10) so that firmware can detect collision signal
> and apply the CSMA/CD algorithm applicable for half duplex operation. A DT
> property, "ti,half-duplex-capable" is introduced for this purpose. If
> board has PHY COL pin conencted to PRGx_PRU1_GPIO10, this DT property can
> be added to eth node of ICSSG, MII port to support half duplex operation at
> that port.
> 
> Reviewed-by: Roger Quadros <rogerq@kernel.org>
> Signed-off-by: MD Danish Anwar <danishanwar@ti.com>

Reviewed-by: Andrew Lunn <andrew@lunn.ch>

    Andrew