1. Patchew
  2. linux
  3. [PATCH v1 0/9] media: qcom: camss: Bugfix series
  4. View patch

[PATCH v1 9/9] media: qcom: camss: Fix csid-gen2 for test pattern generator

Bryan O'Donoghue posted 9 patches 2 years, 3 months ago
There is a newer version of this series
[PATCH v1 9/9] media: qcom: camss: Fix csid-gen2 for test pattern generator
Posted by Bryan O'Donoghue 2 years, 3 months ago 
From: Andrey Konovalov <andrey.konovalov@linaro.org>

In the current driver csid Test Pattern Generator (TPG) doesn't work.
This change:
- fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
- fixes the shift by one between test_pattern control value and the
  actual pattern.
So that TPG starts working, but with the below limitations:
- only test_pattern=9 works as it should
- test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
- the rest of test_pattern's don't work (yavta doesn't get the data)
- regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
  order is always the same (RGGB for any RAW8 or RAW10P format in
  4608x2592 resolution).

Tested with:

RAW10P format, VC0:
 media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
 media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
 media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
 v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
 yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0

RAW10P format, VC1:
 media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
 media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
 media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
 v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
 yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1

RAW8 format, VC0:
 media-ctl --reset
 media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
 media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
 media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
 yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0

Fixes: eebe6d00e9bf ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
 drivers/media/platform/qcom/camss/camss-csid-gen2.c | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)

diff --git a/drivers/media/platform/qcom/camss/camss-csid-gen2.c b/drivers/media/platform/qcom/camss/camss-csid-gen2.c
index 140c584bfb8b1..6ba2b10326444 100644
--- a/drivers/media/platform/qcom/camss/camss-csid-gen2.c
+++ b/drivers/media/platform/qcom/camss/camss-csid-gen2.c
@@ -355,9 +355,6 @@ static void __csid_configure_stream(struct csid_device *csid, u8 enable, u8 vc)
 		u8 dt_id = vc;
 
 		if (tg->enabled) {
-			/* Config Test Generator */
-			vc = 0xa;
-
 			/* configure one DT, infinite frames */
 			val = vc << TPG_VC_CFG0_VC_NUM;
 			val |= INTELEAVING_MODE_ONE_SHOT << TPG_VC_CFG0_LINE_INTERLEAVING_MODE;
@@ -370,14 +367,14 @@ static void __csid_configure_stream(struct csid_device *csid, u8 enable, u8 vc)
 
 			writel_relaxed(0x12345678, csid->base + CSID_TPG_LFSR_SEED);
 
-			val = input_format->height & 0x1fff << TPG_DT_n_CFG_0_FRAME_HEIGHT;
-			val |= input_format->width & 0x1fff << TPG_DT_n_CFG_0_FRAME_WIDTH;
+			val = (input_format->height & 0x1fff) << TPG_DT_n_CFG_0_FRAME_HEIGHT;
+			val |= (input_format->width & 0x1fff) << TPG_DT_n_CFG_0_FRAME_WIDTH;
 			writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_0(0));
 
 			val = format->data_type << TPG_DT_n_CFG_1_DATA_TYPE;
 			writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_1(0));
 
-			val = tg->mode << TPG_DT_n_CFG_2_PAYLOAD_MODE;
+			val = (tg->mode - 1) << TPG_DT_n_CFG_2_PAYLOAD_MODE;
 			val |= 0xBE << TPG_DT_n_CFG_2_USER_SPECIFIED_PAYLOAD;
 			val |= format->decode_format << TPG_DT_n_CFG_2_ENCODE_FORMAT;
 			writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_2(0));
-- 
2.41.0
Re: [PATCH v1 9/9] media: qcom: camss: Fix csid-gen2 for test pattern generator
Posted by Konrad Dybcio 2 years, 3 months ago 
On 22.08.2023 18:16, Bryan O'Donoghue wrote:
> From: Andrey Konovalov <andrey.konovalov@linaro.org>
> 
> In the current driver csid Test Pattern Generator (TPG) doesn't work.
> This change:
> - fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
> - fixes the shift by one between test_pattern control value and the
>   actual pattern.
> So that TPG starts working, but with the below limitations:
> - only test_pattern=9 works as it should
> - test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
> - the rest of test_pattern's don't work (yavta doesn't get the data)
> - regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
>   order is always the same (RGGB for any RAW8 or RAW10P format in
>   4608x2592 resolution).
> 
> Tested with:
> 
> RAW10P format, VC0:
>  media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
>  media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
>  media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
>  v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
>  yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0
> 
> RAW10P format, VC1:
>  media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
>  media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
>  media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
>  v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
>  yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1
> 
> RAW8 format, VC0:
>  media-ctl --reset
>  media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
>  media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
>  media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
>  yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0
> 
> Fixes: eebe6d00e9bf ("media: camss: Add support for CSID hardware version Titan 170")
> Cc: stable@vger.kernel.org
> Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
That's a whole lot to unroll..

[...]
>  		if (tg->enabled) {
> -			/* Config Test Generator */
> -			vc = 0xa;
> -
Which part does this hunk correlate to?

>  			/* configure one DT, infinite frames */
>  			val = vc << TPG_VC_CFG0_VC_NUM;
>  			val |= INTELEAVING_MODE_ONE_SHOT << TPG_VC_CFG0_LINE_INTERLEAVING_MODE;
> @@ -370,14 +367,14 @@ static void __csid_configure_stream(struct csid_device *csid, u8 enable, u8 vc)
>  
>  			writel_relaxed(0x12345678, csid->base + CSID_TPG_LFSR_SEED);
>  
> -			val = input_format->height & 0x1fff << TPG_DT_n_CFG_0_FRAME_HEIGHT;
> -			val |= input_format->width & 0x1fff << TPG_DT_n_CFG_0_FRAME_WIDTH;
> +			val = (input_format->height & 0x1fff) << TPG_DT_n_CFG_0_FRAME_HEIGHT;
> +			val |= (input_format->width & 0x1fff) << TPG_DT_n_CFG_0_FRAME_WIDTH;
>  			writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_0(0));
This screams necessity for FIELD_PREP/GET! Could you please convert
it in another series if you have time for it?

Konrad
Re: [PATCH v1 9/9] media: qcom: camss: Fix csid-gen2 for test pattern generator
Posted by Bryan O'Donoghue 2 years, 3 months ago 
On 22/08/2023 17:38, Konrad Dybcio wrote:
> On 22.08.2023 18:16, Bryan O'Donoghue wrote:
>> From: Andrey Konovalov <andrey.konovalov@linaro.org>
>>
>> In the current driver csid Test Pattern Generator (TPG) doesn't work.
>> This change:
>> - fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
>> - fixes the shift by one between test_pattern control value and the
>>    actual pattern.
>> So that TPG starts working, but with the below limitations:
>> - only test_pattern=9 works as it should
>> - test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
>> - the rest of test_pattern's don't work (yavta doesn't get the data)
>> - regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
>>    order is always the same (RGGB for any RAW8 or RAW10P format in
>>    4608x2592 resolution).
>>
>> Tested with:
>>
>> RAW10P format, VC0:
>>   media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
>>   media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
>>   media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
>>   v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
>>   yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0
>>
>> RAW10P format, VC1:
>>   media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
>>   media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
>>   media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
>>   v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
>>   yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1
>>
>> RAW8 format, VC0:
>>   media-ctl --reset
>>   media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
>>   media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
>>   media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
>>   yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0
>>
>> Fixes: eebe6d00e9bf ("media: camss: Add support for CSID hardware version Titan 170")
>> Cc: stable@vger.kernel.org
>> Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
>> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
>> ---
> That's a whole lot to unroll..
> 
> [...]
>>   		if (tg->enabled) {
>> -			/* Config Test Generator */
>> -			vc = 0xa;
>> -
> Which part does this hunk correlate to?
> 
>>   			/* configure one DT, infinite frames */
>>   			val = vc << TPG_VC_CFG0_VC_NUM;
>>   			val |= INTELEAVING_MODE_ONE_SHOT << TPG_VC_CFG0_LINE_INTERLEAVING_MODE;
>> @@ -370,14 +367,14 @@ static void __csid_configure_stream(struct csid_device *csid, u8 enable, u8 vc)
>>   
>>   			writel_relaxed(0x12345678, csid->base + CSID_TPG_LFSR_SEED);
>>   
>> -			val = input_format->height & 0x1fff << TPG_DT_n_CFG_0_FRAME_HEIGHT;
>> -			val |= input_format->width & 0x1fff << TPG_DT_n_CFG_0_FRAME_WIDTH;
>> +			val = (input_format->height & 0x1fff) << TPG_DT_n_CFG_0_FRAME_HEIGHT;
>> +			val |= (input_format->width & 0x1fff) << TPG_DT_n_CFG_0_FRAME_WIDTH;
>>   			writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_0(0));
> This screams necessity for FIELD_PREP/GET! Could you please convert
> it in another series if you have time for it?

I mean yes I want to or want it done. To me 1 << somevalue is just silly 
when you can say BIT(somevalue).

There will be a "make it pretty series".

I'll do a V2 of this series and explain in the commit log what's 
happening with the removal of vc = 0xa; since if someone has to ask, its 
not obvious whats going on.

---
bod

Patchew 2.1-devel-b67e4c2

© 2016 - 2025 Red Hat, Inc.