There's an irq hooked up, so let's describe it.

Prior to commit 9757300d2750
("pinctrl: qcom: Add intr_target_width field to support increased number of interrupt targets")
one would not see the IRQ fire, despite some (invasive) debugging
showing that the GPIO was in fact asserted, resulting in the interface
staying down.

Now that the IRQ is properly routed we can describe it.

Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
---
 arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
index 8fde6935cd6e..9760bb4b468c 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
@@ -295,6 +295,7 @@ sgmii_phy1: phy@a {
 			compatible = "ethernet-phy-id0141.0dd4";
 			reg = <0xa>;
 			device_type = "ethernet-phy";
+			interrupts-extended = <&tlmm 26 IRQ_TYPE_EDGE_FALLING>;
 			reset-gpios = <&pmm8654au_2_gpios 9 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <11000>;
 			reset-deassert-us = <70000>;
-- 
2.41.0

On Thu, Aug 17, 2023 at 11:38 PM Andrew Halaney <ahalaney@redhat.com> wrote:
>
> There's an irq hooked up, so let's describe it.
>
> Prior to commit 9757300d2750
> ("pinctrl: qcom: Add intr_target_width field to support increased number of interrupt targets")
> one would not see the IRQ fire, despite some (invasive) debugging
> showing that the GPIO was in fact asserted, resulting in the interface
> staying down.
>
> Now that the IRQ is properly routed we can describe it.
>
> Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
> ---
>  arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 1 +
>  1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> index 8fde6935cd6e..9760bb4b468c 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
> @@ -295,6 +295,7 @@ sgmii_phy1: phy@a {
>                         compatible = "ethernet-phy-id0141.0dd4";
>                         reg = <0xa>;
>                         device_type = "ethernet-phy";
> +                       interrupts-extended = <&tlmm 26 IRQ_TYPE_EDGE_FALLING>;
>                         reset-gpios = <&pmm8654au_2_gpios 9 GPIO_ACTIVE_LOW>;
>                         reset-assert-us = <11000>;
>                         reset-deassert-us = <70000>;
> --
> 2.41.0
>

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

On 17.08.2023 23:37, Andrew Halaney wrote:
> There's an irq hooked up, so let's describe it.
> 
> Prior to commit 9757300d2750
> ("pinctrl: qcom: Add intr_target_width field to support increased number of interrupt targets")
> one would not see the IRQ fire, despite some (invasive) debugging
> showing that the GPIO was in fact asserted, resulting in the interface
> staying down.
> 
> Now that the IRQ is properly routed we can describe it.
> 
> Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad