From: "Chengci.Xu" <chengci.xu@mediatek.com>
If there are many ports in a infra master, current flow will update
the INFRA register many times. This patch saves all ports to portid_msk
in the front of mtk_iommu_config(), then update only once for the IOMMU
configure. After this, we could avoid send too many SMC calls to ATF in
MT8188.
Prepare for MT8188, also reduce the indention without functional change.
Signed-off-by: Chengci.Xu <chengci.xu@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
drivers/iommu/mtk_iommu.c | 58 +++++++++++++++++++++------------------
1 file changed, 32 insertions(+), 26 deletions(-)
diff --git a/drivers/iommu/mtk_iommu.c b/drivers/iommu/mtk_iommu.c
index 7287be67bd1f..8cff85615d5e 100644
--- a/drivers/iommu/mtk_iommu.c
+++ b/drivers/iommu/mtk_iommu.c
@@ -579,41 +579,47 @@ static int mtk_iommu_config(struct mtk_iommu_data *data, struct device *dev,
unsigned int larbid, portid;
struct iommu_fwspec *fwspec = dev_iommu_fwspec_get(dev);
const struct mtk_iommu_iova_region *region;
- u32 peri_mmuen, peri_mmuen_msk;
+ unsigned long portid_msk = 0;
int i, ret = 0;
for (i = 0; i < fwspec->num_ids; ++i) {
- larbid = MTK_M4U_TO_LARB(fwspec->ids[i]);
portid = MTK_M4U_TO_PORT(fwspec->ids[i]);
+ portid_msk |= BIT(portid);
+ }
- if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_MM)) {
- larb_mmu = &data->larb_imu[larbid];
+ if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_MM)) {
+ /* All ports should be in the same larb. just use 0 here */
+ larbid = MTK_M4U_TO_LARB(fwspec->ids[0]);
+ larb_mmu = &data->larb_imu[larbid];
+ region = data->plat_data->iova_region + regionid;
- region = data->plat_data->iova_region + regionid;
+ for_each_set_bit(portid, &portid_msk, 32)
larb_mmu->bank[portid] = upper_32_bits(region->iova_base);
- dev_dbg(dev, "%s iommu for larb(%s) port %d region %d rgn-bank %d.\n",
- enable ? "enable" : "disable", dev_name(larb_mmu->dev),
- portid, regionid, larb_mmu->bank[portid]);
-
- if (enable)
- larb_mmu->mmu |= MTK_SMI_MMU_EN(portid);
- else
- larb_mmu->mmu &= ~MTK_SMI_MMU_EN(portid);
- } else if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_INFRA)) {
- peri_mmuen_msk = BIT(portid);
- /* PCI dev has only one output id, enable the next writing bit for PCIe */
- if (dev_is_pci(dev))
- peri_mmuen_msk |= BIT(portid + 1);
-
- peri_mmuen = enable ? peri_mmuen_msk : 0;
- ret = regmap_update_bits(data->pericfg, PERICFG_IOMMU_1,
- peri_mmuen_msk, peri_mmuen);
- if (ret)
- dev_err(dev, "%s iommu(%s) inframaster 0x%x fail(%d).\n",
- enable ? "enable" : "disable",
- dev_name(data->dev), peri_mmuen_msk, ret);
+ dev_dbg(dev, "%s iommu for larb(%s) port 0x%lx region %d rgn-bank %d.\n",
+ enable ? "enable" : "disable", dev_name(larb_mmu->dev),
+ portid_msk, regionid, upper_32_bits(region->iova_base));
+
+ if (enable)
+ larb_mmu->mmu |= portid_msk;
+ else
+ larb_mmu->mmu &= ~portid_msk;
+ } else if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_INFRA)) {
+ /* PCI dev has only one output id, enable the next writing bit for PCIe */
+ if (dev_is_pci(dev)) {
+ if (fwspec->num_ids != 1) {
+ dev_err(dev, "PCI dev can only have one port.\n");
+ return -ENODEV;
+ }
+ portid_msk |= BIT(portid + 1);
}
+
+ ret = regmap_update_bits(data->pericfg, PERICFG_IOMMU_1,
+ (u32)portid_msk, enable ? (u32)portid_msk : 0);
+ if (ret)
+ dev_err(dev, "%s iommu(%s) inframaster 0x%lx fail(%d).\n",
+ enable ? "enable" : "disable",
+ dev_name(data->dev), portid_msk, ret);
}
return ret;
}
--
2.25.1