Add support for HDMA NATIVE, as long the IP design has set
the compatible register map parameter-HDMA_NATIVE,
which allows compatibility for native HDMA register configuration.

The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP.
And the native HDMA registers are different from eDMA,
so this patch add support for HDMA NATIVE mode.

HDMA write and read channels operate independently to maximize
the performance of the HDMA read and write data transfer over
the link When you configure the HDMA with multiple read channels,
then it uses a round robin (RR) arbitration scheme to select
the next read channel to be serviced.The same applies when
youhave multiple write channels.

The native HDMA driver also supports a maximum of 16 independent
channels (8 write + 8 read), which can run simultaneously.
Both SAR (Source Address Register) and DAR (Destination Address Register)
are aligned to byte.

Cai Huoqing (4):
  dmaengine: dw-edma: Rename dw_edma_core_ops structure to
    dw_edma_plat_ops
  dmaengine: dw-edma: Create a new dw_edma_core_ops structure to
    abstract controller operation
  dmaengine: dw-edma: Add support for native HDMA
  dmaengine: dw-edma: Add HDMA DebugFS support

Tested-by: Serge Semin <fancer.lancer@gmail.com>

v10->v11: Using single name in commit log.

v10 link:
https://lore.kernel.org/lkml/20230517030115.21093-1-cai.huoqing@linux.dev/

 drivers/dma/dw-edma/Makefile                 |   8 +-
 drivers/dma/dw-edma/dw-edma-core.c           |  86 ++----
 drivers/dma/dw-edma/dw-edma-core.h           |  58 ++++
 drivers/dma/dw-edma/dw-edma-pcie.c           |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-core.c        |  85 +++++-
 drivers/dma/dw-edma/dw-edma-v0-core.h        |  14 +-
 drivers/dma/dw-edma/dw-hdma-v0-core.c        | 296 +++++++++++++++++++
 drivers/dma/dw-edma/dw-hdma-v0-core.h        |  17 ++
 drivers/dma/dw-edma/dw-hdma-v0-debugfs.c     | 170 +++++++++++
 drivers/dma/dw-edma/dw-hdma-v0-debugfs.h     |  22 ++
 drivers/dma/dw-edma/dw-hdma-v0-regs.h        | 129 ++++++++
 drivers/pci/controller/dwc/pcie-designware.c |   2 +-
 include/linux/dma/edma.h                     |   7 +-
 13 files changed, 807 insertions(+), 91 deletions(-)
 create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.c
 create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.h
 create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.c
 create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-debugfs.h
 create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-regs.h

-- 
2.34.1

On 20-05-23, 13:08, Cai Huoqing wrote:
> Add support for HDMA NATIVE, as long the IP design has set
> the compatible register map parameter-HDMA_NATIVE,
> which allows compatibility for native HDMA register configuration.
> 
> The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP.
> And the native HDMA registers are different from eDMA,
> so this patch add support for HDMA NATIVE mode.
> 
> HDMA write and read channels operate independently to maximize
> the performance of the HDMA read and write data transfer over
> the link When you configure the HDMA with multiple read channels,
> then it uses a round robin (RR) arbitration scheme to select
> the next read channel to be serviced.The same applies when
> youhave multiple write channels.
> 
> The native HDMA driver also supports a maximum of 16 independent
> channels (8 write + 8 read), which can run simultaneously.
> Both SAR (Source Address Register) and DAR (Destination Address Register)
> are aligned to byte.

Applied, thanks

-- 
~Vinod