.../phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml | 1 + .../bindings/phy/qcom,usb-snps-femto-v2.yaml | 1 + .../devicetree/bindings/usb/qcom,dwc3.yaml | 5 + arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 92 +++++++ arch/arm64/boot/dts/qcom/sa8775p.dtsi | 239 +++++++++++++++++- drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 45 ++++ 6 files changed, 381 insertions(+), 2 deletions(-)
Update relavent DT bindings for USB, add new config to the phy driver,
add USB and PHY nodes to the .dtsi and enable them in the board .dts
for the sa8775p-ride platform.
Shazad Hussain (6):
dt-bindings: usb: qcom,dwc3: Add bindings for SA8775P
dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for SA8775P
dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add SA8775P USB PHY
binding
phy: qcom-qmp: Add SA8775P USB3 UNI phy
arm64: dts: qcom: sa8775p: add USB nodes
arm64: dts: qcom: sa8775p-ride: enable USB nodes
.../phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml | 1 +
.../bindings/phy/qcom,usb-snps-femto-v2.yaml | 1 +
.../devicetree/bindings/usb/qcom,dwc3.yaml | 5 +
arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 92 +++++++
arch/arm64/boot/dts/qcom/sa8775p.dtsi | 239 +++++++++++++++++-
drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 45 ++++
6 files changed, 381 insertions(+), 2 deletions(-)
--
2.17.1
Hi Shazad,
On Fri, Apr 21, 2023 at 07:09:15PM +0530, Shazad Hussain wrote:
> Update relavent DT bindings for USB, add new config to the phy driver,
> add USB and PHY nodes to the .dtsi and enable them in the board .dts
> for the sa8775p-ride platform.
>
> Shazad Hussain (6):
> dt-bindings: usb: qcom,dwc3: Add bindings for SA8775P
> dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for SA8775P
> dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add SA8775P USB PHY
> binding
> phy: qcom-qmp: Add SA8775P USB3 UNI phy
> arm64: dts: qcom: sa8775p: add USB nodes
> arm64: dts: qcom: sa8775p-ride: enable USB nodes
>
> .../phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml | 1 +
> .../bindings/phy/qcom,usb-snps-femto-v2.yaml | 1 +
> .../devicetree/bindings/usb/qcom,dwc3.yaml | 5 +
> arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 92 +++++++
> arch/arm64/boot/dts/qcom/sa8775p.dtsi | 239 +++++++++++++++++-
> drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 45 ++++
> 6 files changed, 381 insertions(+), 2 deletions(-)
>
> --
> 2.17.1
>
Thanks for posting this. I tested the series on the sa8775p, and it seems
initialization for the controller at a400000 sometimes fails with a
timeout (-110) error:
dwc3 a400000.usb: Adding to iommu group 2
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: can't setup: -110
xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
xhci-hcd: probe of xhci-hcd.0.auto failed with error -110
dwc3 a600000.usb: Adding to iommu group 3
dwc3 a800000.usb: Adding to iommu group 4
xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.1.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010
xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a800000
xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.1.auto: Host supports USB 3.1 Enhanced SuperSpeed
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
In this case, only usb devices for a800000 are showing:
dracut:/# ls -alh /sys/bus/usb/devices
total 0
drwxr-xr-x 2 root root 0 Feb 27 00:00 .
drwxr-xr-x 4 root root 0 Feb 27 00:00 ..
lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1/1-0:1.0
lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2/2-0:1.0
lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1
lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2
This happens approximately 1 out of 2 reboots. Here's the kernel output
when initialization succeeds:
dwc3 a600000.usb: Adding to iommu group 2
dwc3 a800000.usb: Adding to iommu group 3
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010
xhci-hcd xhci-hcd.0.auto: irq 161, io mem 0x0a800000
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.1 Enhanced SuperSpeed
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
dwc3 a400000.usb: Adding to iommu group 4
xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
xhci-hcd xhci-hcd.1.auto: USB3 root hub has no ports
xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000000010010
xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a400000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
And the list of usb devices:
dracut:/# ls -alh /sys/bus/usb/devices
total 0
drwxr-xr-x 2 root root 0 Feb 27 00:00 .
drwxr-xr-x 4 root root 0 Feb 27 00:00 ..
lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1/1-0:1.0
lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2/2-0:1.0
lrwxrwxrwx 1 root root 0 Feb 27 00:00 3-0:1.0 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3/3-0:1.0
lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1
lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2
lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb3 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3
Have you also encountered this?
Best,
Adrien
On 4/24/23 23:35, Adrien Thierry wrote: > Hi Shazad, > > On Fri, Apr 21, 2023 at 07:09:15PM +0530, Shazad Hussain wrote: >> Update relavent DT bindings for USB, add new config to the phy driver, >> add USB and PHY nodes to the .dtsi and enable them in the board .dts >> for the sa8775p-ride platform. >> >> Shazad Hussain (6): >> dt-bindings: usb: qcom,dwc3: Add bindings for SA8775P >> dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for SA8775P >> dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add SA8775P USB PHY >> binding >> phy: qcom-qmp: Add SA8775P USB3 UNI phy >> arm64: dts: qcom: sa8775p: add USB nodes >> arm64: dts: qcom: sa8775p-ride: enable USB nodes >> >> .../phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml | 1 + >> .../bindings/phy/qcom,usb-snps-femto-v2.yaml | 1 + >> .../devicetree/bindings/usb/qcom,dwc3.yaml | 5 + >> arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 92 +++++++ >> arch/arm64/boot/dts/qcom/sa8775p.dtsi | 239 +++++++++++++++++- >> drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 45 ++++ >> 6 files changed, 381 insertions(+), 2 deletions(-) >> >> -- >> 2.17.1 >> > Thanks for posting this. I tested the series on the sa8775p, and it seems > initialization for the controller at a400000 sometimes fails with a > timeout (-110) error: > > dwc3 a400000.usb: Adding to iommu group 2 > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.0.auto: can't setup: -110 > xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered > xhci-hcd: probe of xhci-hcd.0.auto failed with error -110 > dwc3 a600000.usb: Adding to iommu group 3 > dwc3 a800000.usb: Adding to iommu group 4 > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.1.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010 > xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a800000 > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 > xhci-hcd xhci-hcd.1.auto: Host supports USB 3.1 Enhanced SuperSpeed > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > > In this case, only usb devices for a800000 are showing: > > dracut:/# ls -alh /sys/bus/usb/devices > total 0 > drwxr-xr-x 2 root root 0 Feb 27 00:00 . > drwxr-xr-x 4 root root 0 Feb 27 00:00 .. > lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1/1-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2/2-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2 > > This happens approximately 1 out of 2 reboots. Here's the kernel output > when initialization succeeds: > > dwc3 a600000.usb: Adding to iommu group 2 > dwc3 a800000.usb: Adding to iommu group 3 > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.0.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010 > xhci-hcd xhci-hcd.0.auto: irq 161, io mem 0x0a800000 > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 > xhci-hcd xhci-hcd.0.auto: Host supports USB 3.1 Enhanced SuperSpeed > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > dwc3 a400000.usb: Adding to iommu group 4 > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 > xhci-hcd xhci-hcd.1.auto: USB3 root hub has no ports > xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000000010010 > xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a400000 > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 1 port detected > > And the list of usb devices: > > dracut:/# ls -alh /sys/bus/usb/devices > total 0 > drwxr-xr-x 2 root root 0 Feb 27 00:00 . > drwxr-xr-x 4 root root 0 Feb 27 00:00 .. > lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1/1-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2/2-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 3-0:1.0 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3/3-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb3 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3 > > Have you also encountered this? I've had some issues with QMPPHY not (sometimes?) probing in time on SM6115 only when built as a module.. perhaps it'd be worth checking out of it works fine with =y? Konrad > > Best, > > Adrien >
Hi Konrad, On Thu, Apr 27, 2023 at 12:42:15AM +0100, Konrad Dybcio wrote: > > On 4/24/23 23:35, Adrien Thierry wrote: > > Hi Shazad, > > > > On Fri, Apr 21, 2023 at 07:09:15PM +0530, Shazad Hussain wrote: > > > Update relavent DT bindings for USB, add new config to the phy driver, > > > add USB and PHY nodes to the .dtsi and enable them in the board .dts > > > for the sa8775p-ride platform. > > > > > > Shazad Hussain (6): > > > dt-bindings: usb: qcom,dwc3: Add bindings for SA8775P > > > dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for SA8775P > > > dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add SA8775P USB PHY > > > binding > > > phy: qcom-qmp: Add SA8775P USB3 UNI phy > > > arm64: dts: qcom: sa8775p: add USB nodes > > > arm64: dts: qcom: sa8775p-ride: enable USB nodes > > > > > > .../phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml | 1 + > > > .../bindings/phy/qcom,usb-snps-femto-v2.yaml | 1 + > > > .../devicetree/bindings/usb/qcom,dwc3.yaml | 5 + > > > arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 92 +++++++ > > > arch/arm64/boot/dts/qcom/sa8775p.dtsi | 239 +++++++++++++++++- > > > drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 45 ++++ > > > 6 files changed, 381 insertions(+), 2 deletions(-) > > > > > > -- > > > 2.17.1 > > > > > Thanks for posting this. I tested the series on the sa8775p, and it seems > > initialization for the controller at a400000 sometimes fails with a > > timeout (-110) error: > > > > dwc3 a400000.usb: Adding to iommu group 2 > > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 > > xhci-hcd xhci-hcd.0.auto: can't setup: -110 > > xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered > > xhci-hcd: probe of xhci-hcd.0.auto failed with error -110 > > dwc3 a600000.usb: Adding to iommu group 3 > > dwc3 a800000.usb: Adding to iommu group 4 > > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 > > xhci-hcd xhci-hcd.1.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010 > > xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a800000 > > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 > > xhci-hcd xhci-hcd.1.auto: Host supports USB 3.1 Enhanced SuperSpeed > > hub 1-0:1.0: USB hub found > > hub 1-0:1.0: 1 port detected > > usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. > > hub 2-0:1.0: USB hub found > > hub 2-0:1.0: 1 port detected > > > > In this case, only usb devices for a800000 are showing: > > > > dracut:/# ls -alh /sys/bus/usb/devices > > total 0 > > drwxr-xr-x 2 root root 0 Feb 27 00:00 . > > drwxr-xr-x 4 root root 0 Feb 27 00:00 .. > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1/1-0:1.0 > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2/2-0:1.0 > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1 > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2 > > > > This happens approximately 1 out of 2 reboots. Here's the kernel output > > when initialization succeeds: > > > > dwc3 a600000.usb: Adding to iommu group 2 > > dwc3 a800000.usb: Adding to iommu group 3 > > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 > > xhci-hcd xhci-hcd.0.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010 > > xhci-hcd xhci-hcd.0.auto: irq 161, io mem 0x0a800000 > > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 > > xhci-hcd xhci-hcd.0.auto: Host supports USB 3.1 Enhanced SuperSpeed > > hub 1-0:1.0: USB hub found > > hub 1-0:1.0: 1 port detected > > usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. > > hub 2-0:1.0: USB hub found > > hub 2-0:1.0: 1 port detected > > dwc3 a400000.usb: Adding to iommu group 4 > > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 > > xhci-hcd xhci-hcd.1.auto: USB3 root hub has no ports > > xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000000010010 > > xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a400000 > > hub 3-0:1.0: USB hub found > > hub 3-0:1.0: 1 port detected > > > > And the list of usb devices: > > > > dracut:/# ls -alh /sys/bus/usb/devices > > total 0 > > drwxr-xr-x 2 root root 0 Feb 27 00:00 . > > drwxr-xr-x 4 root root 0 Feb 27 00:00 .. > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1/1-0:1.0 > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2/2-0:1.0 > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 3-0:1.0 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3/3-0:1.0 > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1 > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2 > > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb3 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3 > > > > Have you also encountered this? > > I've had some issues with QMPPHY not (sometimes?) probing in time on SM6115 only when built as a module.. perhaps it'd be worth checking out of it works fine with =y? Looks like that might be the cause indeed. The arm64 defconfig has the PHYs built as modules, but with either CONFIG_PHY_QCOM_QMP_USB=y or CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2=y, the controllers initialize properly all the time. So, the series is: Tested-by: Adrien Thierry <athierry@redhat.com> > > > Konrad > > > > > Best, > > > > Adrien > >
On 4/27/2023 5:12 AM, Konrad Dybcio wrote: > > On 4/24/23 23:35, Adrien Thierry wrote: >> Hi Shazad, >> >> On Fri, Apr 21, 2023 at 07:09:15PM +0530, Shazad Hussain wrote: >>> Update relavent DT bindings for USB, add new config to the phy driver, >>> add USB and PHY nodes to the .dtsi and enable them in the board .dts >>> for the sa8775p-ride platform. >>> >>> Shazad Hussain (6): >>> dt-bindings: usb: qcom,dwc3: Add bindings for SA8775P >>> dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for SA8775P >>> dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add SA8775P USB PHY >>> binding >>> phy: qcom-qmp: Add SA8775P USB3 UNI phy >>> arm64: dts: qcom: sa8775p: add USB nodes >>> arm64: dts: qcom: sa8775p-ride: enable USB nodes >>> >>> .../phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml | 1 + >>> .../bindings/phy/qcom,usb-snps-femto-v2.yaml | 1 + >>> .../devicetree/bindings/usb/qcom,dwc3.yaml | 5 + >>> arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 92 +++++++ >>> arch/arm64/boot/dts/qcom/sa8775p.dtsi | 239 +++++++++++++++++- >>> drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 45 ++++ >>> 6 files changed, 381 insertions(+), 2 deletions(-) >>> >>> -- >>> 2.17.1 >>> >> Thanks for posting this. I tested the series on the sa8775p, and it seems >> initialization for the controller at a400000 sometimes fails with a >> timeout (-110) error: >> >> dwc3 a400000.usb: Adding to iommu group 2 >> xhci-hcd xhci-hcd.0.auto: xHCI Host Controller >> xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus >> number 1 >> xhci-hcd xhci-hcd.0.auto: can't setup: -110 >> xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered >> xhci-hcd: probe of xhci-hcd.0.auto failed with error -110 >> dwc3 a600000.usb: Adding to iommu group 3 >> dwc3 a800000.usb: Adding to iommu group 4 >> xhci-hcd xhci-hcd.1.auto: xHCI Host Controller >> xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus >> number 1 >> xhci-hcd xhci-hcd.1.auto: hcc params 0x0110ffc5 hci version 0x110 >> quirks 0x0000000000010010 >> xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a800000 >> xhci-hcd xhci-hcd.1.auto: xHCI Host Controller >> xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus >> number 2 >> xhci-hcd xhci-hcd.1.auto: Host supports USB 3.1 Enhanced SuperSpeed >> hub 1-0:1.0: USB hub found >> hub 1-0:1.0: 1 port detected >> usb usb2: We don't know the algorithms for LPM for this host, >> disabling LPM. >> hub 2-0:1.0: USB hub found >> hub 2-0:1.0: 1 port detected >> >> In this case, only usb devices for a800000 are showing: >> >> dracut:/# ls -alh /sys/bus/usb/devices >> total 0 >> drwxr-xr-x 2 root root 0 Feb 27 00:00 . >> drwxr-xr-x 4 root root 0 Feb 27 00:00 .. >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> >> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1/1-0:1.0 >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> >> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2/2-0:1.0 >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> >> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1 >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> >> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2 >> >> This happens approximately 1 out of 2 reboots. Here's the kernel output >> when initialization succeeds: >> >> dwc3 a600000.usb: Adding to iommu group 2 >> dwc3 a800000.usb: Adding to iommu group 3 >> xhci-hcd xhci-hcd.0.auto: xHCI Host Controller >> xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus >> number 1 >> xhci-hcd xhci-hcd.0.auto: hcc params 0x0110ffc5 hci version 0x110 >> quirks 0x0000000000010010 >> xhci-hcd xhci-hcd.0.auto: irq 161, io mem 0x0a800000 >> xhci-hcd xhci-hcd.0.auto: xHCI Host Controller >> xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus >> number 2 >> xhci-hcd xhci-hcd.0.auto: Host supports USB 3.1 Enhanced SuperSpeed >> hub 1-0:1.0: USB hub found >> hub 1-0:1.0: 1 port detected >> usb usb2: We don't know the algorithms for LPM for this host, >> disabling LPM. >> hub 2-0:1.0: USB hub found >> hub 2-0:1.0: 1 port detected >> dwc3 a400000.usb: Adding to iommu group 4 >> xhci-hcd xhci-hcd.1.auto: xHCI Host Controller >> xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus >> number 3 >> xhci-hcd xhci-hcd.1.auto: USB3 root hub has no ports >> xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 >> quirks 0x0000000000010010 >> xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a400000 >> hub 3-0:1.0: USB hub found >> hub 3-0:1.0: 1 port detected >> >> And the list of usb devices: >> >> dracut:/# ls -alh /sys/bus/usb/devices >> total 0 >> drwxr-xr-x 2 root root 0 Feb 27 00:00 . >> drwxr-xr-x 4 root root 0 Feb 27 00:00 .. >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> >> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1/1-0:1.0 >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> >> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2/2-0:1.0 >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 3-0:1.0 -> >> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3/3-0:1.0 >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> >> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1 >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> >> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2 >> lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb3 -> >> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3 >> >> Have you also encountered this? > > I've had some issues with QMPPHY not (sometimes?) probing in time on > SM6115 only when built as a module.. perhaps it'd be worth checking out > of it works fine with =y? > In my setup I tried keeping QMPPHY as =y only and did not see the issue with 10 reboots. > > Konrad > >> >> Best, >> >> Adrien >> --- Shazad
Hi Adrien, On 4/25/2023 4:05 AM, Adrien Thierry wrote: > Hi Shazad, > > On Fri, Apr 21, 2023 at 07:09:15PM +0530, Shazad Hussain wrote: >> Update relavent DT bindings for USB, add new config to the phy driver, >> add USB and PHY nodes to the .dtsi and enable them in the board .dts >> for the sa8775p-ride platform. >> >> Shazad Hussain (6): >> dt-bindings: usb: qcom,dwc3: Add bindings for SA8775P >> dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for SA8775P >> dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add SA8775P USB PHY >> binding >> phy: qcom-qmp: Add SA8775P USB3 UNI phy >> arm64: dts: qcom: sa8775p: add USB nodes >> arm64: dts: qcom: sa8775p-ride: enable USB nodes >> >> .../phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml | 1 + >> .../bindings/phy/qcom,usb-snps-femto-v2.yaml | 1 + >> .../devicetree/bindings/usb/qcom,dwc3.yaml | 5 + >> arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 92 +++++++ >> arch/arm64/boot/dts/qcom/sa8775p.dtsi | 239 +++++++++++++++++- >> drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 45 ++++ >> 6 files changed, 381 insertions(+), 2 deletions(-) >> >> -- >> 2.17.1 >> > > Thanks for posting this. I tested the series on the sa8775p, and it seems > initialization for the controller at a400000 sometimes fails with a > timeout (-110) error: > > dwc3 a400000.usb: Adding to iommu group 2 > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.0.auto: can't setup: -110 > xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered > xhci-hcd: probe of xhci-hcd.0.auto failed with error -110 > dwc3 a600000.usb: Adding to iommu group 3 > dwc3 a800000.usb: Adding to iommu group 4 > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.1.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010 > xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a800000 > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 > xhci-hcd xhci-hcd.1.auto: Host supports USB 3.1 Enhanced SuperSpeed > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > > In this case, only usb devices for a800000 are showing: > > dracut:/# ls -alh /sys/bus/usb/devices > total 0 > drwxr-xr-x 2 root root 0 Feb 27 00:00 . > drwxr-xr-x 4 root root 0 Feb 27 00:00 .. > lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1/1-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2/2-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2 > > This happens approximately 1 out of 2 reboots. Here's the kernel output > when initialization succeeds: > > dwc3 a600000.usb: Adding to iommu group 2 > dwc3 a800000.usb: Adding to iommu group 3 > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.0.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010 > xhci-hcd xhci-hcd.0.auto: irq 161, io mem 0x0a800000 > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 > xhci-hcd xhci-hcd.0.auto: Host supports USB 3.1 Enhanced SuperSpeed > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > dwc3 a400000.usb: Adding to iommu group 4 > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 > xhci-hcd xhci-hcd.1.auto: USB3 root hub has no ports > xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000000010010 > xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a400000 > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 1 port detected > > And the list of usb devices: > > dracut:/# ls -alh /sys/bus/usb/devices > total 0 > drwxr-xr-x 2 root root 0 Feb 27 00:00 . > drwxr-xr-x 4 root root 0 Feb 27 00:00 .. > lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1/1-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2/2-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 3-0:1.0 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3/3-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb3 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3 > > Have you also encountered this? > I did try 10 reboots and did not encounter this issue on my setup tough. > Best, > > Adrien > --- -Shazad
On Tue, 25 Apr 2023 at 01:36, Adrien Thierry <athierry@redhat.com> wrote: > > Hi Shazad, > > On Fri, Apr 21, 2023 at 07:09:15PM +0530, Shazad Hussain wrote: > > Update relavent DT bindings for USB, add new config to the phy driver, > > add USB and PHY nodes to the .dtsi and enable them in the board .dts > > for the sa8775p-ride platform. > > > > Shazad Hussain (6): > > dt-bindings: usb: qcom,dwc3: Add bindings for SA8775P > > dt-bindings: phy: qcom,usb-snps-femto-v2: Add bindings for SA8775P > > dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: Add SA8775P USB PHY > > binding > > phy: qcom-qmp: Add SA8775P USB3 UNI phy > > arm64: dts: qcom: sa8775p: add USB nodes > > arm64: dts: qcom: sa8775p-ride: enable USB nodes > > > > .../phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml | 1 + > > .../bindings/phy/qcom,usb-snps-femto-v2.yaml | 1 + > > .../devicetree/bindings/usb/qcom,dwc3.yaml | 5 + > > arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 92 +++++++ > > arch/arm64/boot/dts/qcom/sa8775p.dtsi | 239 +++++++++++++++++- > > drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 45 ++++ > > 6 files changed, 381 insertions(+), 2 deletions(-) > > > > -- > > 2.17.1 > > > > Thanks for posting this. I tested the series on the sa8775p, and it seems > initialization for the controller at a400000 sometimes fails with a > timeout (-110) error: > > dwc3 a400000.usb: Adding to iommu group 2 > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.0.auto: can't setup: -110 > xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered > xhci-hcd: probe of xhci-hcd.0.auto failed with error -110 Semi-random suggestion, but could you please try using clk_regmap_phy_mux/clk_regmap_phy_mux_ops for USB pipe clk src? > dwc3 a600000.usb: Adding to iommu group 3 > dwc3 a800000.usb: Adding to iommu group 4 > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.1.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010 > xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a800000 > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 > xhci-hcd xhci-hcd.1.auto: Host supports USB 3.1 Enhanced SuperSpeed > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > > In this case, only usb devices for a800000 are showing: > > dracut:/# ls -alh /sys/bus/usb/devices > total 0 > drwxr-xr-x 2 root root 0 Feb 27 00:00 . > drwxr-xr-x 4 root root 0 Feb 27 00:00 .. > lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1/1-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2/2-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb1 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.1.auto/usb2 > > This happens approximately 1 out of 2 reboots. Here's the kernel output > when initialization succeeds: > > dwc3 a600000.usb: Adding to iommu group 2 > dwc3 a800000.usb: Adding to iommu group 3 > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.0.auto: hcc params 0x0110ffc5 hci version 0x110 quirks 0x0000000000010010 > xhci-hcd xhci-hcd.0.auto: irq 161, io mem 0x0a800000 > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 > xhci-hcd xhci-hcd.0.auto: Host supports USB 3.1 Enhanced SuperSpeed > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > dwc3 a400000.usb: Adding to iommu group 4 > xhci-hcd xhci-hcd.1.auto: xHCI Host Controller > xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 > xhci-hcd xhci-hcd.1.auto: USB3 root hub has no ports > xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000000000010010 > xhci-hcd xhci-hcd.1.auto: irq 162, io mem 0x0a400000 > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 1 port detected > > And the list of usb devices: > > dracut:/# ls -alh /sys/bus/usb/devices > total 0 > drwxr-xr-x 2 root root 0 Feb 27 00:00 . > drwxr-xr-x 4 root root 0 Feb 27 00:00 .. > lrwxrwxrwx 1 root root 0 Feb 27 00:00 1-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1/1-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 2-0:1.0 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2/2-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 3-0:1.0 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3/3-0:1.0 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb1 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb1 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb2 -> ../../../devices/platform/soc@0/a8f8800.usb/a800000.usb/xhci-hcd.0.auto/usb2 > lrwxrwxrwx 1 root root 0 Feb 27 00:00 usb3 -> ../../../devices/platform/soc@0/a4f8800.usb/a400000.usb/xhci-hcd.1.auto/usb3 > > Have you also encountered this? > > Best, > > Adrien > -- With best wishes Dmitry
Hi Dmitry, > Semi-random suggestion, but could you please try using > clk_regmap_phy_mux/clk_regmap_phy_mux_ops for USB pipe clk src? Which specific clock are you refering to? I'm not very familiar with those, in the device tree I'm seeing "pipe" clocks for usb_0 and usb_1 phys, but not for usb_2, which is the one that's causing issues. Best, Adrien
On 25/04/2023 21:03, Adrien Thierry wrote: > Hi Dmitry, > >> Semi-random suggestion, but could you please try using >> clk_regmap_phy_mux/clk_regmap_phy_mux_ops for USB pipe clk src? > > Which specific clock are you refering to? I'm not very familiar with > those, in the device tree I'm seeing "pipe" clocks for usb_0 and usb_1 > phys, but not for usb_2, which is the one that's causing issues. > Ah, I see. Could you please try adding the 'qcom,select-utmi-as-pipe-clk' property to the usb_2 host node and running the test again? -- With best wishes Dmitry
Hi Dmitry, On Sat, Apr 29, 2023 at 12:41:39AM +0300, Dmitry Baryshkov wrote: > On 25/04/2023 21:03, Adrien Thierry wrote: > > Hi Dmitry, > > > > > Semi-random suggestion, but could you please try using > > > clk_regmap_phy_mux/clk_regmap_phy_mux_ops for USB pipe clk src? > > > > Which specific clock are you refering to? I'm not very familiar with > > those, in the device tree I'm seeing "pipe" clocks for usb_0 and usb_1 > > phys, but not for usb_2, which is the one that's causing issues. > > > > Ah, I see. Could you please try adding the 'qcom,select-utmi-as-pipe-clk' > property to the usb_2 host node and running the test again? > Thanks for the suggestion. I tested this but unfortunately the issue is still happening. Best, Adrien
© 2016 - 2025 Red Hat, Inc.