TPM devices may insert wait state on last clock cycle of ADDR phase.
For SPI controllers that support full-duplex transfers, this can be
detected using software by reading the MISO line. For SPI controllers
that only support half-duplex transfers, such as the Tegra QSPI, it is
not possible to detect the wait signal from software. The QSPI
controller in Tegra234 and Tegra241 implement hardware detection of the
wait signal which can be enabled in the controller for TPM devices.

Add HW flow control in TIS driver and a flag in SPI data to indicate
wait detection is required in HW. SPI controller driver determines if
this is supported. Add HW detection in Tegra QSPI controller.

Updates in this patch set 
 - Tegra QSPI identifies itself as half duplex.
 - TPM TIS SPI driver skips flow control for half duplex and send
   transfers in single message for controller to handle it.
 - TPM device identifies as TPM device for controller to detect and
   enable HW TPM wait poll feature.

Verified with a TPM device on Tegra241 ref board using TPM2 tools.

V10
 - use spi_sync in place of spi_sync_locked
V9
 - renamed tpm spi transfer functions
V8:
 - fix compile warning.
V7:
 - updated patch description.
 - TPM flag set in probe.
 - minor comments.
V6:
 - Fix typo in chip name Tegra234.
 - Debug logs change skipped to be sent later.
 - Consistent usage of soc flag.
V5:
 - No SPI bus locking.
V4:
 - Split api change to different patch.
 - Describe TPM HW flow control.
V3:
 - Use SPI device mode flag and SPI controller flags.
 - Drop usage of device tree flags.
 - Generic TPM half duplex controller handling.
 - HW & SW flow control for TPM. Drop additional driver.
V2:
 - Fix dt schema errors.

Krishna Yarlagadda (3):
  spi: Add TPM HW flow flag
  tpm_tis-spi: Add hardware wait polling
  spi: tegra210-quad: Enable TPM wait polling

 drivers/char/tpm/tpm_tis_spi_main.c | 91 ++++++++++++++++++++++++++++-
 drivers/spi/spi-tegra210-quad.c     | 14 +++++
 include/linux/spi/spi.h             | 16 ++++-
 3 files changed, 116 insertions(+), 5 deletions(-)

-- 
2.17.1

On Fri, Apr 21, 2023 at 02:43:06PM +0530, Krishna Yarlagadda wrote:
> TPM devices may insert wait state on last clock cycle of ADDR phase.
> For SPI controllers that support full-duplex transfers, this can be
> detected using software by reading the MISO line. For SPI controllers
> that only support half-duplex transfers, such as the Tegra QSPI, it is
> not possible to detect the wait signal from software. The QSPI
> controller in Tegra234 and Tegra241 implement hardware detection of the
> wait signal which can be enabled in the controller for TPM devices.
> 
> Add HW flow control in TIS driver and a flag in SPI data to indicate
> wait detection is required in HW. SPI controller driver determines if
> this is supported. Add HW detection in Tegra QSPI controller.
> 
> Updates in this patch set 
>  - Tegra QSPI identifies itself as half duplex.
>  - TPM TIS SPI driver skips flow control for half duplex and send
>    transfers in single message for controller to handle it.
>  - TPM device identifies as TPM device for controller to detect and
>    enable HW TPM wait poll feature.
> 
> Verified with a TPM device on Tegra241 ref board using TPM2 tools.
> 
> V10
>  - use spi_sync in place of spi_sync_locked
> V9
>  - renamed tpm spi transfer functions
> V8:
>  - fix compile warning.
> V7:
>  - updated patch description.
>  - TPM flag set in probe.
>  - minor comments.
> V6:
>  - Fix typo in chip name Tegra234.
>  - Debug logs change skipped to be sent later.
>  - Consistent usage of soc flag.
> V5:
>  - No SPI bus locking.
> V4:
>  - Split api change to different patch.
>  - Describe TPM HW flow control.
> V3:
>  - Use SPI device mode flag and SPI controller flags.
>  - Drop usage of device tree flags.
>  - Generic TPM half duplex controller handling.
>  - HW & SW flow control for TPM. Drop additional driver.
> V2:
>  - Fix dt schema errors.
> 
> Krishna Yarlagadda (3):
>   spi: Add TPM HW flow flag
>   tpm_tis-spi: Add hardware wait polling
>   spi: tegra210-quad: Enable TPM wait polling
> 
>  drivers/char/tpm/tpm_tis_spi_main.c | 91 ++++++++++++++++++++++++++++-
>  drivers/spi/spi-tegra210-quad.c     | 14 +++++
>  include/linux/spi/spi.h             | 16 ++++-
>  3 files changed, 116 insertions(+), 5 deletions(-)
> 
> -- 
> 2.17.1
> 

Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>

On Fri, 21 Apr 2023 14:43:06 +0530, Krishna Yarlagadda wrote:
> TPM devices may insert wait state on last clock cycle of ADDR phase.
> For SPI controllers that support full-duplex transfers, this can be
> detected using software by reading the MISO line. For SPI controllers
> that only support half-duplex transfers, such as the Tegra QSPI, it is
> not possible to detect the wait signal from software. The QSPI
> controller in Tegra234 and Tegra241 implement hardware detection of the
> wait signal which can be enabled in the controller for TPM devices.
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[1/3] spi: Add TPM HW flow flag
      commit: 67a142dc9eb96a5cc018e5db62390665eb5f038c
[3/3] spi: tegra210-quad: Enable TPM wait polling
      commit: 967ca91a996f82219f2883e9e53d8e20df49025a

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark