Enable qupv3_id_1 and gpi_dma1 as they are required for configuring
touchscreen. Also add pinctrl configurations needed for touchscreen.
These are common for both the tianma and ebbg touchscreen variant.
In the subsequent patch, we will initially enable support for the focaltech
touchscreen used in the EBBG variant. This is done in preparation for that.

Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
---
 .../qcom/sdm845-xiaomi-beryllium-common.dtsi  | 39 +++++++++++++++++++
 1 file changed, 39 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
index 5ed975cc6ecb..b580a32fdc3b 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
@@ -268,6 +268,10 @@ &gmu {
 	status = "okay";
 };
 
+&gpi_dma1 {
+	status = "okay";
+};
+
 &gpu {
 	status = "okay";
 
@@ -376,6 +380,10 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_1 {
+	status = "okay";
+};
+
 &sdhc_2 {
 	status = "okay";
 
@@ -481,6 +489,37 @@ sdc2_card_det_n: sd-card-det-n-state {
 		function = "gpio";
 		bias-pull-up;
 	};
+
+	ts_int_default: ts-int-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-down;
+		input-enable;
+	};
+
+	ts_reset_default: ts-reset-default-state {
+		pins = "gpio32";
+		function = "gpio";
+		drive-strength = <16>;
+		output-high;
+	};
+
+	ts_int_sleep: ts-int-sleep-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+		input-enable;
+	};
+
+	ts_reset_sleep: ts-reset-sleep-state {
+		pins = "gpio32";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
 };
 
 &uart6 {
-- 
2.40.0

On 10/04/2023 18:01, Joel Selvaraj wrote:
> Enable qupv3_id_1 and gpi_dma1 as they are required for configuring
> touchscreen. Also add pinctrl configurations needed for touchscreen.
> These are common for both the tianma and ebbg touchscreen variant.
> In the subsequent patch, we will initially enable support for the focaltech
> touchscreen used in the EBBG variant. This is done in preparation for that.
> 
> Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
> ---
>  .../qcom/sdm845-xiaomi-beryllium-common.dtsi  | 39 +++++++++++++++++++
>  1 file changed, 39 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
> index 5ed975cc6ecb..b580a32fdc3b 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
> @@ -268,6 +268,10 @@ &gmu {
>  	status = "okay";
>  };
>  
> +&gpi_dma1 {
> +	status = "okay";
> +};
> +
>  &gpu {
>  	status = "okay";
>  
> @@ -376,6 +380,10 @@ &qupv3_id_0 {
>  	status = "okay";
>  };
>  
> +&qupv3_id_1 {
> +	status = "okay";
> +};
> +
>  &sdhc_2 {
>  	status = "okay";
>  
> @@ -481,6 +489,37 @@ sdc2_card_det_n: sd-card-det-n-state {
>  		function = "gpio";
>  		bias-pull-up;
>  	};
> +
> +	ts_int_default: ts-int-default-state {
> +		pins = "gpio31";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		bias-pull-down;
> +		input-enable;

input-enable is not valid.

> +	};
> +
> +	ts_reset_default: ts-reset-default-state {
> +		pins = "gpio32";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		output-high;
> +	};
> +
> +	ts_int_sleep: ts-int-sleep-state {
> +		pins = "gpio31";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +		input-enable;

input-enable is not valid.

Best regards,
Krzysztof