1. Patchew
  2. linux
  3. View series

[PATCH] arm64: dts: ti: k3-j784s4-evm: Add OSPI0 flash support

Apurva Nandan posted 1 patch 2 years, 10 months ago
There is a newer version of this series
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts      | 44 +++++++++++++++++++
.../boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi     | 43 ++++++++++++++++++
2 files changed, 87 insertions(+)
[PATCH] arm64: dts: ti: k3-j784s4-evm: Add OSPI0 flash support
Posted by Apurva Nandan 2 years, 10 months ago 
Add support for OSPI flash connected to OSPI0 instance through FSS.
Also enumerate OSPI1 instance in MCU DTSI.

Signed-off-by: Apurva Nandan <a-nandan@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts      | 44 +++++++++++++++++++
 .../boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi     | 43 ++++++++++++++++++
 2 files changed, 87 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 8cd4a7ecc121..7480f37e89e8 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -138,6 +138,24 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
 			J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
 		>;
 	};
+
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+		pinctrl-single,pins = <
+			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
+			J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
+			J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
+			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
+			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
+			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
+			J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
+			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
+			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
+			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
+			J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
+			J784S4_WKUP_IOPAD(0x03c, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_CSn3.MCU_OSPI0_ECC_FAIL */
+			J784S4_WKUP_IOPAD(0x038, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_CSn2.MCU_OSPI0_RESET_OUT0 */
+		>;
+	};
 };
 
 &main_uart8 {
@@ -146,6 +164,32 @@ &main_uart8 {
 	pinctrl-0 = <&main_uart8_pins_default>;
 };
 
+&fss {
+	status = "okay";
+};
+
+&ospi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+		cdns,phy-mode;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
 &main_i2c0 {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
index 93952af618f6..b29b95a532f6 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
@@ -308,4 +308,47 @@ cpts@3d000 {
 			ti,cpts-periodic-outputs = <2>;
 		};
 	};
+
+	fss: syscon@47000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x00 0x47000000 0x00 0x100>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		status = "disabled";
+
+		ospi0: spi@47040000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x47040000 0x00 0x100>,
+			      <0x5 0x0000000 0x1 0x0000000>;
+			interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 161 7>;
+			assigned-clocks = <&k3_clks 161 7>;
+			assigned-clock-parents = <&k3_clks 161 9>;
+			assigned-clock-rates = <166666666>;
+			power-domains = <&k3_pds 161 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		ospi1: spi@47050000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x47050000 0x00 0x100>,
+			      <0x7 0x0000000 0x1 0x0000000>;
+			interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 162 7>;
+			power-domains = <&k3_pds 162 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+	};
+
 };
-- 
2.34.1
Re: [PATCH] arm64: dts: ti: k3-j784s4-evm: Add OSPI0 flash support
Posted by Raghavendra, Vignesh 2 years, 10 months ago 

On 3/27/2023 1:59 PM, Apurva Nandan wrote:
> Add support for OSPI flash connected to OSPI0 instance through FSS.
> Also enumerate OSPI1 instance in MCU DTSI.
> 
> Signed-off-by: Apurva Nandan <a-nandan@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-j784s4-evm.dts      | 44 +++++++++++++++++++
>  .../boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi     | 43 ++++++++++++++++++
>  2 files changed, 87 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> index 8cd4a7ecc121..7480f37e89e8 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> @@ -138,6 +138,24 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
>  			J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
>  		>;
>  	};
> +
> +	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
> +		pinctrl-single,pins = <
> +			J784S4_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (E32) MCU_OSPI0_CLK */
> +			J784S4_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (A32) MCU_OSPI0_CSn0 */
> +			J784S4_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (B33) MCU_OSPI0_D0 */
> +			J784S4_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (B32) MCU_OSPI0_D1 */
> +			J784S4_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (C33) MCU_OSPI0_D2 */
> +			J784S4_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (C35) MCU_OSPI0_D3 */
> +			J784S4_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (D33) MCU_OSPI0_D4 */
> +			J784S4_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (D34) MCU_OSPI0_D5 */
> +			J784S4_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (E34) MCU_OSPI0_D6 */
> +			J784S4_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (E33) MCU_OSPI0_D7 */
> +			J784S4_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (C34) MCU_OSPI0_DQS */
> +			J784S4_WKUP_IOPAD(0x03c, PIN_OUTPUT, 6) /* (C32) MCU_OSPI0_CSn3.MCU_OSPI0_ECC_FAIL */
> +			J784S4_WKUP_IOPAD(0x038, PIN_OUTPUT, 6) /* (B34) MCU_OSPI0_CSn2.MCU_OSPI0_RESET_OUT0 */
> +		>;
> +	};
>  };
>  
>  &main_uart8 {
> @@ -146,6 +164,32 @@ &main_uart8 {
>  	pinctrl-0 = <&main_uart8_pins_default>;
>  };
>  
> +&fss {
> +	status = "okay";
> +};
> +
> +&ospi0 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +
> +	flash@0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0x0>;
> +		spi-tx-bus-width = <8>;
> +		spi-rx-bus-width = <8>;
> +		spi-max-frequency = <25000000>;
> +		cdns,tshsl-ns = <60>;
> +		cdns,tsd2d-ns = <60>;
> +		cdns,tchsh-ns = <60>;
> +		cdns,tslch-ns = <60>;
> +		cdns,read-delay = <4>;

> +		cdns,phy-mode;

Need binding doc

> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +	};
> +};
> +
>  &main_i2c0 {
>  	status = "okay";
>  	pinctrl-names = "default";
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> index 93952af618f6..b29b95a532f6 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> @@ -308,4 +308,47 @@ cpts@3d000 {
>  			ti,cpts-periodic-outputs = <2>;
>  		};
>  	};
> +
> +	fss: syscon@47000000 {
> +		compatible = "syscon", "simple-mfd";

NACK. Please run make dtbs_check and fix all the issues..

See whats being done for J721s2 [0] for example

[0] https://lore.kernel.org/linux-arm-kernel/20230309082940.31535-1-r-gunasekaran@ti.com/

> +		reg = <0x00 0x47000000 0x00 0x100>;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +		status = "disabled";

Lets keep the FSS enabled as there is not board dependency
and disable individual SPI controllers

> +
> +		ospi0: spi@47040000 {
> +			compatible = "ti,am654-ospi", "cdns,qspi-nor";
> +			reg = <0x00 0x47040000 0x00 0x100>,
> +			      <0x5 0x0000000 0x1 0x0000000>;

			      <0x05 0x0000000 0x01 0x0000000>;

> +			interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
> +			cdns,fifo-depth = <256>;
> +			cdns,fifo-width = <4>;
> +			cdns,trigger-address = <0x0>;
> +			clocks = <&k3_clks 161 7>;
> +			assigned-clocks = <&k3_clks 161 7>;
> +			assigned-clock-parents = <&k3_clks 161 9>;
> +			assigned-clock-rates = <166666666>;
> +			power-domains = <&k3_pds 161 TI_SCI_PD_EXCLUSIVE>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		ospi1: spi@47050000 {
> +			compatible = "ti,am654-ospi", "cdns,qspi-nor";
> +			reg = <0x00 0x47050000 0x00 0x100>,
> +			      <0x7 0x0000000 0x1 0x0000000>;


			      <0x07 0x0000000 0x01 0x0000000>;


> +			interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
> +			cdns,fifo-depth = <256>;
> +			cdns,fifo-width = <4>;
> +			cdns,trigger-address = <0x0>;
> +			clocks = <&k3_clks 162 7>;
> +			power-domains = <&k3_pds 162 TI_SCI_PD_EXCLUSIVE>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +	};
> +
>  };


Regards
Vignesh
Re: [PATCH] arm64: dts: ti: k3-j784s4-evm: Add OSPI0 flash support
Posted by Krzysztof Kozlowski 2 years, 10 months ago 
On 27/03/2023 10:29, Apurva Nandan wrote:
> Add support for OSPI flash connected to OSPI0 instance through FSS.
> Also enumerate OSPI1 instance in MCU DTSI.



> +
> +&ospi0 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +
> +	flash@0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0x0>;
> +		spi-tx-bus-width = <8>;
> +		spi-rx-bus-width = <8>;
> +		spi-max-frequency = <25000000>;
> +		cdns,tshsl-ns = <60>;
> +		cdns,tsd2d-ns = <60>;
> +		cdns,tchsh-ns = <60>;
> +		cdns,tslch-ns = <60>;
> +		cdns,read-delay = <4>;
> +		cdns,phy-mode;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +	};
> +};
> +
>  &main_i2c0 {
>  	status = "okay";
>  	pinctrl-names = "default";
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> index 93952af618f6..b29b95a532f6 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
> @@ -308,4 +308,47 @@ cpts@3d000 {
>  			ti,cpts-periodic-outputs = <2>;
>  		};
>  	};
> +
> +	fss: syscon@47000000 {
> +		compatible = "syscon", "simple-mfd";

NAK. This is not allowed on itself and dtbs_check would warn you.

> +		reg = <0x00 0x47000000 0x00 0x100>;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +		status = "disabled";
> +
> +		ospi0: spi@47040000 {
> +			compatible = "ti,am654-ospi", "cdns,qspi-nor";
> +			reg = <0x00 0x47040000 0x00 0x100>,
> +			      <0x5 0x0000000 0x1 0x0000000>;
> +			interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
> +			cdns,fifo-depth = <256>;
> +			cdns,fifo-width = <4>;
> +			cdns,trigger-address = <0x0>;
> +			clocks = <&k3_clks 161 7>;
> +			assigned-clocks = <&k3_clks 161 7>;
> +			assigned-clock-parents = <&k3_clks 161 9>;
> +			assigned-clock-rates = <166666666>;
> +			power-domains = <&k3_pds 161 TI_SCI_PD_EXCLUSIVE>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +
> +		ospi1: spi@47050000 {
> +			compatible = "ti,am654-ospi", "cdns,qspi-nor";
> +			reg = <0x00 0x47050000 0x00 0x100>,
> +			      <0x7 0x0000000 0x1 0x0000000>;
> +			interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
> +			cdns,fifo-depth = <256>;
> +			cdns,fifo-width = <4>;
> +			cdns,trigger-address = <0x0>;
> +			clocks = <&k3_clks 162 7>;
> +			power-domains = <&k3_pds 162 TI_SCI_PD_EXCLUSIVE>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			status = "disabled";
> +		};
> +	};
> +

Don't add stay blank lines.

>  };

Best regards,
Krzysztof

Patchew 2.1-devel-b67e4c2

© 2016 - 2026 Red Hat, Inc.