[PATCH v4 17/19] thermal/tegra: Do not enable the thermal zone, it is already enabled

Daniel Lezcano posted 19 patches 1 year, 8 months ago
There is a newer version of this series
[PATCH v4 17/19] thermal/tegra: Do not enable the thermal zone, it is already enabled
Posted by Daniel Lezcano 1 year, 8 months ago
The code enables the thermal zone after setting it up. But the thermal
zone is already enabled by thermal_of_zone_register() function.

Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
---
 drivers/thermal/tegra/tegra30-tsensor.c | 8 +-------
 1 file changed, 1 insertion(+), 7 deletions(-)

diff --git a/drivers/thermal/tegra/tegra30-tsensor.c b/drivers/thermal/tegra/tegra30-tsensor.c
index 3506c3f3c474..e38902abf207 100644
--- a/drivers/thermal/tegra/tegra30-tsensor.c
+++ b/drivers/thermal/tegra/tegra30-tsensor.c
@@ -346,7 +346,7 @@ static int tegra_tsensor_enable_hw_channel(const struct tegra_tsensor *ts,
 {
 	const struct tegra_tsensor_channel *tsc = &ts->ch[id];
 	struct thermal_zone_device *tzd = tsc->tzd;
-	int err, hot_trip = 0, crit_trip = 0;
+	int hot_trip = 0, crit_trip = 0;
 	u32 val;
 
 	if (!tzd) {
@@ -401,12 +401,6 @@ static int tegra_tsensor_enable_hw_channel(const struct tegra_tsensor *ts,
 	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_INTR_THERMAL_RST_EN, 1);
 	writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG0);
 
-	err = thermal_zone_device_enable(tzd);
-	if (err) {
-		dev_err(ts->dev, "ch%u: failed to enable zone: %d\n", id, err);
-		return err;
-	}
-
 	return 0;
 }
 
-- 
2.34.1
Re: [PATCH v4 17/19] thermal/tegra: Do not enable the thermal zone, it is already enabled
Posted by Thierry Reding 1 year, 8 months ago
On Tue, Feb 28, 2023 at 12:22:36PM +0100, Daniel Lezcano wrote:
> The code enables the thermal zone after setting it up. But the thermal
> zone is already enabled by thermal_of_zone_register() function.
> 
> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
> ---
>  drivers/thermal/tegra/tegra30-tsensor.c | 8 +-------
>  1 file changed, 1 insertion(+), 7 deletions(-)
> 
> diff --git a/drivers/thermal/tegra/tegra30-tsensor.c b/drivers/thermal/tegra/tegra30-tsensor.c
> index 3506c3f3c474..e38902abf207 100644
> --- a/drivers/thermal/tegra/tegra30-tsensor.c
> +++ b/drivers/thermal/tegra/tegra30-tsensor.c
> @@ -346,7 +346,7 @@ static int tegra_tsensor_enable_hw_channel(const struct tegra_tsensor *ts,
>  {
>  	const struct tegra_tsensor_channel *tsc = &ts->ch[id];
>  	struct thermal_zone_device *tzd = tsc->tzd;
> -	int err, hot_trip = 0, crit_trip = 0;
> +	int hot_trip = 0, crit_trip = 0;
>  	u32 val;
>  
>  	if (!tzd) {
> @@ -401,12 +401,6 @@ static int tegra_tsensor_enable_hw_channel(const struct tegra_tsensor *ts,
>  	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_INTR_THERMAL_RST_EN, 1);
>  	writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG0);
>  
> -	err = thermal_zone_device_enable(tzd);
> -	if (err) {
> -		dev_err(ts->dev, "ch%u: failed to enable zone: %d\n", id, err);
> -		return err;
> -	}
> -
>  	return 0;
>  }

This function is called in tegra_tsensor_resume() and balances out the
tegra_tsensor_hw_channel() calls from tegra_tsensor_suspend(). If we
remove the call from here, we'll likely end up with the zones disabled
after a resume.

This ends up calling thermal_zone_device_set_mode(), which is a no-op,
basically, if the mode is unchanged, so this seems harmless.

If you need this to change anyway, I suppose we could move the calls to
thermal_zone_device_enable() and move them into suspend/resume instead.
That's a bit tricky to undo in the error recovery paths, but should be
doable.

Thierry
Re: [PATCH v4 17/19] thermal/tegra: Do not enable the thermal zone, it is already enabled
Posted by Daniel Lezcano 1 year, 8 months ago
On 01/03/2023 15:29, Thierry Reding wrote:
> On Tue, Feb 28, 2023 at 12:22:36PM +0100, Daniel Lezcano wrote:
>> The code enables the thermal zone after setting it up. But the thermal
>> zone is already enabled by thermal_of_zone_register() function.
>>
>> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
>> ---
>>   drivers/thermal/tegra/tegra30-tsensor.c | 8 +-------
>>   1 file changed, 1 insertion(+), 7 deletions(-)
>>
>> diff --git a/drivers/thermal/tegra/tegra30-tsensor.c b/drivers/thermal/tegra/tegra30-tsensor.c
>> index 3506c3f3c474..e38902abf207 100644
>> --- a/drivers/thermal/tegra/tegra30-tsensor.c
>> +++ b/drivers/thermal/tegra/tegra30-tsensor.c
>> @@ -346,7 +346,7 @@ static int tegra_tsensor_enable_hw_channel(const struct tegra_tsensor *ts,
>>   {
>>   	const struct tegra_tsensor_channel *tsc = &ts->ch[id];
>>   	struct thermal_zone_device *tzd = tsc->tzd;
>> -	int err, hot_trip = 0, crit_trip = 0;
>> +	int hot_trip = 0, crit_trip = 0;
>>   	u32 val;
>>   
>>   	if (!tzd) {
>> @@ -401,12 +401,6 @@ static int tegra_tsensor_enable_hw_channel(const struct tegra_tsensor *ts,
>>   	val |= FIELD_PREP(TSENSOR_SENSOR0_CONFIG0_INTR_THERMAL_RST_EN, 1);
>>   	writel_relaxed(val, tsc->regs + TSENSOR_SENSOR0_CONFIG0);
>>   
>> -	err = thermal_zone_device_enable(tzd);
>> -	if (err) {
>> -		dev_err(ts->dev, "ch%u: failed to enable zone: %d\n", id, err);
>> -		return err;
>> -	}
>> -
>>   	return 0;
>>   }
> 
> This function is called in tegra_tsensor_resume() and balances out the
> tegra_tsensor_hw_channel() calls from tegra_tsensor_suspend(). If we
> remove the call from here, we'll likely end up with the zones disabled
> after a resume.
> 
> This ends up calling thermal_zone_device_set_mode(), which is a no-op,
> basically, if the mode is unchanged, so this seems harmless.
> 
> If you need this to change anyway, I suppose we could move the calls to
> thermal_zone_device_enable() and move them into suspend/resume instead.
> That's a bit tricky to undo in the error recovery paths, but should be
> doable.

No it is fine, I will just drop this patch from the series.


-- 
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog