The properties of devices in IXP4xx expansion bus need to be also
applied to actual devices' bindings.  Prepare for this by splitting them
to separate intel,ixp4xx-expansion-peripheral-props binding, just like
other memory-controller peripheral properties.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 ...intel,ixp4xx-expansion-bus-controller.yaml | 64 +--------------
 ...tel,ixp4xx-expansion-peripheral-props.yaml | 80 +++++++++++++++++++
 .../mc-peripheral-props.yaml                  |  1 +
 3 files changed, 82 insertions(+), 63 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml

diff --git a/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml b/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
index 5fb4e7bfa4da..a771796ec499 100644
--- a/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
+++ b/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
@@ -56,69 +56,7 @@ patternProperties:
     description: Devices attached to chip selects are represented as
       subnodes.
     type: object
-
-    properties:
-      intel,ixp4xx-eb-t1:
-        description: Address timing, extend address phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 3
-
-      intel,ixp4xx-eb-t2:
-        description: Setup chip select timing, extend setup phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 3
-
-      intel,ixp4xx-eb-t3:
-        description: Strobe timing, extend strobe phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 15
-
-      intel,ixp4xx-eb-t4:
-        description: Hold timing, extend hold phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 3
-
-      intel,ixp4xx-eb-t5:
-        description: Recovery timing, extend recovery phase with n cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        maximum: 15
-
-      intel,ixp4xx-eb-cycle-type:
-        description: The type of cycles to use on the expansion bus for this
-          chip select. 0 = Intel cycles, 1 = Motorola cycles, 2 = HPI cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1, 2]
-
-      intel,ixp4xx-eb-byte-access-on-halfword:
-        description: Allow byte read access on half word devices.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-hpi-hrdy-pol-high:
-        description: Set HPI HRDY polarity to active high when using HPI.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-mux-address-and-data:
-        description: Multiplex address and data on the data bus.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-ahb-split-transfers:
-        description: Enable AHB split transfers.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-write-enable:
-        description: Enable write cycles.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
-
-      intel,ixp4xx-eb-byte-access:
-        description: Expansion bus uses only 8 bits. The default is to use
-          16 bits.
-        $ref: /schemas/types.yaml#/definitions/uint32
-        enum: [0, 1]
+    $ref: /schemas/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml#
 
 required:
   - compatible
diff --git a/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml
new file mode 100644
index 000000000000..8f782c80e88b
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml
@@ -0,0 +1,80 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Peripheral properties for Intel IXP4xx Expansion Bus
+
+description: |
+  The IXP4xx expansion bus controller handles access to devices on the
+  memory-mapped expansion bus on the Intel IXP4xx family of system on chips,
+  including IXP42x, IXP43x, IXP45x and IXP46x.
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+properties:
+  intel,ixp4xx-eb-t1:
+    description: Address timing, extend address phase with n cycles.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 3
+
+  intel,ixp4xx-eb-t2:
+    description: Setup chip select timing, extend setup phase with n cycles.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 3
+
+  intel,ixp4xx-eb-t3:
+    description: Strobe timing, extend strobe phase with n cycles.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+
+  intel,ixp4xx-eb-t4:
+    description: Hold timing, extend hold phase with n cycles.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 3
+
+  intel,ixp4xx-eb-t5:
+    description: Recovery timing, extend recovery phase with n cycles.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    maximum: 15
+
+  intel,ixp4xx-eb-cycle-type:
+    description: The type of cycles to use on the expansion bus for this
+      chip select. 0 = Intel cycles, 1 = Motorola cycles, 2 = HPI cycles.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2]
+
+  intel,ixp4xx-eb-byte-access-on-halfword:
+    description: Allow byte read access on half word devices.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+
+  intel,ixp4xx-eb-hpi-hrdy-pol-high:
+    description: Set HPI HRDY polarity to active high when using HPI.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+
+  intel,ixp4xx-eb-mux-address-and-data:
+    description: Multiplex address and data on the data bus.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+
+  intel,ixp4xx-eb-ahb-split-transfers:
+    description: Enable AHB split transfers.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+
+  intel,ixp4xx-eb-write-enable:
+    description: Enable write cycles.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+
+  intel,ixp4xx-eb-byte-access:
+    description: Expansion bus uses only 8 bits. The default is to use
+      16 bits.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1]
+
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
index 53ae995462db..5acfcad12bb7 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
@@ -34,5 +34,6 @@ required:
 # The controller specific properties go here.
 allOf:
   - $ref: st,stm32-fmc2-ebi-props.yaml#
+  - $ref: intel,ixp4xx-expansion-peripheral-props.yaml#
 
 additionalProperties: true
-- 
2.34.1

On Fri, Jan 27, 2023 at 10:32:15AM +0100, Krzysztof Kozlowski wrote:
> The properties of devices in IXP4xx expansion bus need to be also
> applied to actual devices' bindings.  Prepare for this by splitting them
> to separate intel,ixp4xx-expansion-peripheral-props binding, just like
> other memory-controller peripheral properties.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
>  ...intel,ixp4xx-expansion-bus-controller.yaml | 64 +--------------
>  ...tel,ixp4xx-expansion-peripheral-props.yaml | 80 +++++++++++++++++++

Kind of odd to have these in 2 directories. Can we move 
intel,ixp4xx-expansion-bus-controller.yaml to 
bindings/memory-controllers/?

Or maybe all the external/parallel bus interfaces need their own 
directory?

>  .../mc-peripheral-props.yaml                  |  1 +
>  3 files changed, 82 insertions(+), 63 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml
> 
> diff --git a/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml b/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
> index 5fb4e7bfa4da..a771796ec499 100644
> --- a/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
> +++ b/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
> @@ -56,69 +56,7 @@ patternProperties:
>      description: Devices attached to chip selects are represented as
>        subnodes.
>      type: object
> -
> -    properties:
> -      intel,ixp4xx-eb-t1:
> -        description: Address timing, extend address phase with n cycles.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        maximum: 3
> -
> -      intel,ixp4xx-eb-t2:
> -        description: Setup chip select timing, extend setup phase with n cycles.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        maximum: 3
> -
> -      intel,ixp4xx-eb-t3:
> -        description: Strobe timing, extend strobe phase with n cycles.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        maximum: 15
> -
> -      intel,ixp4xx-eb-t4:
> -        description: Hold timing, extend hold phase with n cycles.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        maximum: 3
> -
> -      intel,ixp4xx-eb-t5:
> -        description: Recovery timing, extend recovery phase with n cycles.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        maximum: 15
> -
> -      intel,ixp4xx-eb-cycle-type:
> -        description: The type of cycles to use on the expansion bus for this
> -          chip select. 0 = Intel cycles, 1 = Motorola cycles, 2 = HPI cycles.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        enum: [0, 1, 2]
> -
> -      intel,ixp4xx-eb-byte-access-on-halfword:
> -        description: Allow byte read access on half word devices.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        enum: [0, 1]
> -
> -      intel,ixp4xx-eb-hpi-hrdy-pol-high:
> -        description: Set HPI HRDY polarity to active high when using HPI.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        enum: [0, 1]
> -
> -      intel,ixp4xx-eb-mux-address-and-data:
> -        description: Multiplex address and data on the data bus.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        enum: [0, 1]
> -
> -      intel,ixp4xx-eb-ahb-split-transfers:
> -        description: Enable AHB split transfers.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        enum: [0, 1]
> -
> -      intel,ixp4xx-eb-write-enable:
> -        description: Enable write cycles.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        enum: [0, 1]
> -
> -      intel,ixp4xx-eb-byte-access:
> -        description: Expansion bus uses only 8 bits. The default is to use
> -          16 bits.
> -        $ref: /schemas/types.yaml#/definitions/uint32
> -        enum: [0, 1]
> +    $ref: /schemas/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml#
>  
>  required:
>    - compatible
> diff --git a/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml
> new file mode 100644
> index 000000000000..8f782c80e88b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml
> @@ -0,0 +1,80 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Peripheral properties for Intel IXP4xx Expansion Bus
> +
> +description: |

Don't need '|'.

> +  The IXP4xx expansion bus controller handles access to devices on the
> +  memory-mapped expansion bus on the Intel IXP4xx family of system on chips,
> +  including IXP42x, IXP43x, IXP45x and IXP46x.
> +
> +maintainers:
> +  - Linus Walleij <linus.walleij@linaro.org>
> +
> +properties:
> +  intel,ixp4xx-eb-t1:
> +    description: Address timing, extend address phase with n cycles.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    maximum: 3
> +
> +  intel,ixp4xx-eb-t2:
> +    description: Setup chip select timing, extend setup phase with n cycles.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    maximum: 3
> +
> +  intel,ixp4xx-eb-t3:
> +    description: Strobe timing, extend strobe phase with n cycles.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    maximum: 15
> +
> +  intel,ixp4xx-eb-t4:
> +    description: Hold timing, extend hold phase with n cycles.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    maximum: 3
> +
> +  intel,ixp4xx-eb-t5:
> +    description: Recovery timing, extend recovery phase with n cycles.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    maximum: 15
> +
> +  intel,ixp4xx-eb-cycle-type:
> +    description: The type of cycles to use on the expansion bus for this
> +      chip select. 0 = Intel cycles, 1 = Motorola cycles, 2 = HPI cycles.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1, 2]
> +
> +  intel,ixp4xx-eb-byte-access-on-halfword:
> +    description: Allow byte read access on half word devices.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1]
> +
> +  intel,ixp4xx-eb-hpi-hrdy-pol-high:
> +    description: Set HPI HRDY polarity to active high when using HPI.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1]
> +
> +  intel,ixp4xx-eb-mux-address-and-data:
> +    description: Multiplex address and data on the data bus.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1]
> +
> +  intel,ixp4xx-eb-ahb-split-transfers:
> +    description: Enable AHB split transfers.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1]
> +
> +  intel,ixp4xx-eb-write-enable:
> +    description: Enable write cycles.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1]
> +
> +  intel,ixp4xx-eb-byte-access:
> +    description: Expansion bus uses only 8 bits. The default is to use
> +      16 bits.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1]
> +
> +additionalProperties: true
> diff --git a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
> index 53ae995462db..5acfcad12bb7 100644
> --- a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
> +++ b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
> @@ -34,5 +34,6 @@ required:
>  # The controller specific properties go here.
>  allOf:
>    - $ref: st,stm32-fmc2-ebi-props.yaml#
> +  - $ref: intel,ixp4xx-expansion-peripheral-props.yaml#
>  
>  additionalProperties: true
> -- 
> 2.34.1
>

On 30/01/2023 20:12, Rob Herring wrote:
> On Fri, Jan 27, 2023 at 10:32:15AM +0100, Krzysztof Kozlowski wrote:
>> The properties of devices in IXP4xx expansion bus need to be also
>> applied to actual devices' bindings.  Prepare for this by splitting them
>> to separate intel,ixp4xx-expansion-peripheral-props binding, just like
>> other memory-controller peripheral properties.
>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> ---
>>  ...intel,ixp4xx-expansion-bus-controller.yaml | 64 +--------------
>>  ...tel,ixp4xx-expansion-peripheral-props.yaml | 80 +++++++++++++++++++
> 
> Kind of odd to have these in 2 directories. Can we move 
> intel,ixp4xx-expansion-bus-controller.yaml to 
> bindings/memory-controllers/?

Indeed mostly we kept them so far in memory-controllers. Some of these
buses are used for attaching some type of memory, but I don't know if
ixp4xx can work like this.

> 
> Or maybe all the external/parallel bus interfaces need their own 
> directory?

Except the IXP4xx, I wouldn't know which one goes where... Example is
exynos-srom which can work with memory (SRAM, ROM, flash) or devices.

I'll move it to memory-controllers.


> 
>>  .../mc-peripheral-props.yaml                  |  1 +
>>  3 files changed, 82 insertions(+), 63 deletions(-)
>>  create mode 100644 Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml b/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
>> index 5fb4e7bfa4da..a771796ec499 100644
>> --- a/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
>> +++ b/Documentation/devicetree/bindings/bus/intel,ixp4xx-expansion-bus-controller.yaml
>> @@ -56,69 +56,7 @@ patternProperties:
>>      description: Devices attached to chip selects are represented as
>>        subnodes.
>>      type: object
>> -
>> -    properties:
>> -      intel,ixp4xx-eb-t1:
>> -        description: Address timing, extend address phase with n cycles.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        maximum: 3
>> -
>> -      intel,ixp4xx-eb-t2:
>> -        description: Setup chip select timing, extend setup phase with n cycles.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        maximum: 3
>> -
>> -      intel,ixp4xx-eb-t3:
>> -        description: Strobe timing, extend strobe phase with n cycles.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        maximum: 15
>> -
>> -      intel,ixp4xx-eb-t4:
>> -        description: Hold timing, extend hold phase with n cycles.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        maximum: 3
>> -
>> -      intel,ixp4xx-eb-t5:
>> -        description: Recovery timing, extend recovery phase with n cycles.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        maximum: 15
>> -
>> -      intel,ixp4xx-eb-cycle-type:
>> -        description: The type of cycles to use on the expansion bus for this
>> -          chip select. 0 = Intel cycles, 1 = Motorola cycles, 2 = HPI cycles.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        enum: [0, 1, 2]
>> -
>> -      intel,ixp4xx-eb-byte-access-on-halfword:
>> -        description: Allow byte read access on half word devices.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        enum: [0, 1]
>> -
>> -      intel,ixp4xx-eb-hpi-hrdy-pol-high:
>> -        description: Set HPI HRDY polarity to active high when using HPI.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        enum: [0, 1]
>> -
>> -      intel,ixp4xx-eb-mux-address-and-data:
>> -        description: Multiplex address and data on the data bus.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        enum: [0, 1]
>> -
>> -      intel,ixp4xx-eb-ahb-split-transfers:
>> -        description: Enable AHB split transfers.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        enum: [0, 1]
>> -
>> -      intel,ixp4xx-eb-write-enable:
>> -        description: Enable write cycles.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        enum: [0, 1]
>> -
>> -      intel,ixp4xx-eb-byte-access:
>> -        description: Expansion bus uses only 8 bits. The default is to use
>> -          16 bits.
>> -        $ref: /schemas/types.yaml#/definitions/uint32
>> -        enum: [0, 1]
>> +    $ref: /schemas/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml#
>>  
>>  required:
>>    - compatible
>> diff --git a/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml
>> new file mode 100644
>> index 000000000000..8f782c80e88b
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml
>> @@ -0,0 +1,80 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/memory-controllers/intel,ixp4xx-expansion-peripheral-props.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Peripheral properties for Intel IXP4xx Expansion Bus
>> +
>> +description: |
> 
> Don't need '|'.

Right.


Best regards,
Krzysztof

On Fri, Jan 27, 2023 at 10:32 AM Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:

> The properties of devices in IXP4xx expansion bus need to be also
> applied to actual devices' bindings.  Prepare for this by splitting them
> to separate intel,ixp4xx-expansion-peripheral-props binding, just like
> other memory-controller peripheral properties.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Whoa, this is a complex one!
But I assume you and Marek know what you're doing so:
Acked-by: Linus Walleij <linus.walleij@linaro.org>

Maybe I can assign the following external bus interface to the Qcom
people, as it is yet another one of those:
Documentation/devicetree/bindings/bus/qcom,ebi2.txt

I've been uncertain about how I should convert that one over properly.

Yours,
Linus Walleij