In preparing to remove the .adjust_link api, I am moving the one-time
initialization of the device's Turbo Mode bit into a different execution
path. This code clears (disables) the Turbo Mode bit which is never used
by this driver. Turbo Mode is a non-standard mode that would allow the
100Mbps RMII interface to run at 200Mbps.

Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
---
 drivers/net/dsa/lan9303-core.c | 14 ++++++--------
 1 file changed, 6 insertions(+), 8 deletions(-)

diff --git a/drivers/net/dsa/lan9303-core.c b/drivers/net/dsa/lan9303-core.c
index 5a21fc96d479..20fc2af62531 100644
--- a/drivers/net/dsa/lan9303-core.c
+++ b/drivers/net/dsa/lan9303-core.c
@@ -886,6 +886,12 @@ static int lan9303_check_device(struct lan9303 *chip)
 		return ret;
 	}
 
+	/* Virtual Phy: Remove Turbo 200Mbit mode */
+	lan9303_read(chip->regmap, LAN9303_VIRT_SPECIAL_CTRL, &reg);
+
+	reg &= ~LAN9303_VIRT_SPECIAL_TURBO;
+	regmap_write(chip->regmap, LAN9303_VIRT_SPECIAL_CTRL, reg);
+
 	return 0;
 }
 
@@ -1073,14 +1079,6 @@ static void lan9303_adjust_link(struct dsa_switch *ds, int port,
 		ctl &= ~BMCR_FULLDPLX;
 
 	lan9303_phy_write(ds, port, MII_BMCR, ctl);
-
-	if (port == chip->phy_addr_base) {
-		/* Virtual Phy: Remove Turbo 200Mbit mode */
-		lan9303_read(chip->regmap, LAN9303_VIRT_SPECIAL_CTRL, &ctl);
-
-		ctl &= ~LAN9303_VIRT_SPECIAL_TURBO;
-		regmap_write(chip->regmap, LAN9303_VIRT_SPECIAL_CTRL, ctl);
-	}
 }
 
 static int lan9303_port_enable(struct dsa_switch *ds, int port,
-- 
2.17.1

On Fri, 9 Dec 2022 16:47:09 -0600 Jerry Ray wrote:
> In preparing to remove the .adjust_link api, I am moving the one-time
> initialization of the device's Turbo Mode bit into a different execution
> path. This code clears (disables) the Turbo Mode bit which is never used
> by this driver. Turbo Mode is a non-standard mode that would allow the
> 100Mbps RMII interface to run at 200Mbps.

> @@ -1073,14 +1079,6 @@ static void lan9303_adjust_link(struct dsa_switch *ds, int port,
>  		ctl &= ~BMCR_FULLDPLX;
>  
>  	lan9303_phy_write(ds, port, MII_BMCR, ctl);
> -
> -	if (port == chip->phy_addr_base) {
> -		/* Virtual Phy: Remove Turbo 200Mbit mode */
> -		lan9303_read(chip->regmap, LAN9303_VIRT_SPECIAL_CTRL, &ctl);
> -
> -		ctl &= ~LAN9303_VIRT_SPECIAL_TURBO;
> -		regmap_write(chip->regmap, LAN9303_VIRT_SPECIAL_CTRL, ctl);
> -	}
>  }
>  
>  static int lan9303_port_enable(struct dsa_switch *ds, int port,

The chip variable has to go, otherwise there will be a warning in
bisection until patch 6 removes this entire function:

drivers/net/dsa/lan9303-core.c:1059:18: warning: unused variable 'chip' [-Wunused-variable]
        struct lan9303 *chip = ds->priv;
                        ^