.../devicetree/bindings/net/dsa/lan9303.txt | 99 +------------- .../bindings/net/dsa/microchip,lan9303.yaml | 129 ++++++++++++++++++ MAINTAINERS | 8 ++ 3 files changed, 139 insertions(+), 97 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml
Adding the dt binding yaml for the lan9303 3-port ethernet switch.
The microchip lan9354 3-port ethernet switch will also use the
same binding.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
---
v2->v3:
- removed cpu labels
- now patching against latest net-next
v1->v2:
- fixed dt_binding_check warning
- added max-speed setting on the switches 10/100 ports.
---
.../devicetree/bindings/net/dsa/lan9303.txt | 99 +-------------
.../bindings/net/dsa/microchip,lan9303.yaml | 129 ++++++++++++++++++
MAINTAINERS | 8 ++
3 files changed, 139 insertions(+), 97 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml
diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
index 46a732087f5c..8c8fedd1f00e 100644
--- a/Documentation/devicetree/bindings/net/dsa/lan9303.txt
+++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
@@ -1,100 +1,5 @@
SMSC/MicroChip LAN9303 three port ethernet switch
-------------------------------------------------
-Required properties:
-
-- compatible: should be
- - "smsc,lan9303-i2c" for I2C managed mode
- or
- - "smsc,lan9303-mdio" for mdio managed mode
-
-Optional properties:
-
-- reset-gpios: GPIO to be used to reset the whole device
-- reset-duration: reset duration in milliseconds, defaults to 200 ms
-
-Subnodes:
-
-The integrated switch subnode should be specified according to the binding
-described in dsa/dsa.txt. The CPU port of this switch is always port 0.
-
-Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is
-configured to use 1/2/3 instead. This hardware configuration will be
-auto-detected and mapped accordingly.
-
-Example:
-
-I2C managed mode:
-
- master: masterdevice@X {
-
- fixed-link { /* RMII fixed link to LAN9303 */
- speed = <100>;
- full-duplex;
- };
- };
-
- switch: switch@a {
- compatible = "smsc,lan9303-i2c";
- reg = <0xa>;
- reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
- reset-duration = <200>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 { /* RMII fixed link to master */
- reg = <0>;
- ethernet = <&master>;
- };
-
- port@1 { /* external port 1 */
- reg = <1>;
- label = "lan1";
- };
-
- port@2 { /* external port 2 */
- reg = <2>;
- label = "lan2";
- };
- };
- };
-
-MDIO managed mode:
-
- master: masterdevice@X {
- phy-handle = <&switch>;
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- switch: switch-phy@0 {
- compatible = "smsc,lan9303-mdio";
- reg = <0>;
- reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
- reset-duration = <100>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- ethernet = <&master>;
- };
-
- port@1 { /* external port 1 */
- reg = <1>;
- label = "lan1";
- };
-
- port@2 { /* external port 2 */
- reg = <2>;
- label = "lan2";
- };
- };
- };
- };
- };
+See Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml for the
+device tree documentation covering the LAN9303 and LAN9354 devices.
diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml
new file mode 100644
index 000000000000..818770092a2c
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml
@@ -0,0 +1,129 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/microchip,lan9303.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: LAN9303 Ethernet Switch Series Tree Bindings
+
+allOf:
+ - $ref: "dsa.yaml#"
+
+maintainers:
+ - UNGLinuxDriver@microchip.com
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - smsc,lan9303-mdio
+ - microchip,lan9354-mdio
+ - enum:
+ - smsc,lan9303-i2c
+
+ reg:
+ maxItems: 1
+
+ reset-gpios:
+ description: Optional gpio specifier for a reset line
+ maxItems: 1
+
+ reset-duration:
+ description: Reset duration in milliseconds, defaults to 200 ms
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ //Ethernet switch connected via mdio to the host
+ ethernet0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy-handle = <&lan9303switch>;
+ phy-mode = "rmii";
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ lan9303switch: switch@0 {
+ compatible = "smsc,lan9303-mdio";
+ dsa,member = <0 0>;
+ reg = <0>;
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ phy-mode = "rmii";
+ ethernet = <ðernet>;
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ max-speed = <100>;
+ label = "lan1";
+ };
+ port@2 {
+ reg = <2>;
+ max-speed = <100>;
+ label = "lan2";
+ };
+ };
+ };
+ };
+ };
+
+ //Ethernet switch connected via i2c to the host
+ ethernet1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy-mode = "rmii";
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ lan9303: switch@1a {
+ compatible = "smsc,lan9303-i2c";
+ reg = <0x1a>;
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ phy-mode = "rmii";
+ ethernet = <ðernet1>;
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+ port@1 {
+ reg = <1>;
+ max-speed = <100>;
+ label = "lan1";
+ };
+ port@2 {
+ reg = <2>;
+ max-speed = <100>;
+ label = "lan2";
+ };
+ };
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 5d58b55c5ae5..89055ff2838a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13386,6 +13386,14 @@ L: netdev@vger.kernel.org
S: Maintained
F: drivers/net/ethernet/microchip/lan743x_*
+MICROCHIP LAN9303/LAN9354 ETHERNET SWITCH DRIVER
+M: Jerry Ray <jerry.ray@microchip.com>
+M: UNGLinuxDriver@microchip.com
+L: netdev@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml
+F: drivers/net/dsa/lan9303*
+
MICROCHIP LAN966X ETHERNET DRIVER
M: Horatiu Vultur <horatiu.vultur@microchip.com>
M: UNGLinuxDriver@microchip.com
--
2.25.1On 28/09/2022 18:21, Jerry Ray wrote:
> Adding the dt binding yaml for the lan9303 3-port ethernet switch.
> The microchip lan9354 3-port ethernet switch will also use the
> same binding.
>
> Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
> ---
> v2->v3:
> - removed cpu labels
> - now patching against latest net-next
> v1->v2:
> - fixed dt_binding_check warning
> - added max-speed setting on the switches 10/100 ports.
> ---
> .../devicetree/bindings/net/dsa/lan9303.txt | 99 +-------------
> .../bindings/net/dsa/microchip,lan9303.yaml | 129 ++++++++++++++++++
> MAINTAINERS | 8 ++
> 3 files changed, 139 insertions(+), 97 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml
>
> diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
> index 46a732087f5c..8c8fedd1f00e 100644
> --- a/Documentation/devicetree/bindings/net/dsa/lan9303.txt
> +++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt
> @@ -1,100 +1,5 @@
> SMSC/MicroChip LAN9303 three port ethernet switch
> -------------------------------------------------
Old file should be entirely removed.
>
> -Required properties:
> -
> -- compatible: should be
> - - "smsc,lan9303-i2c" for I2C managed mode
> - or
> - - "smsc,lan9303-mdio" for mdio managed mode
> -
> -Optional properties:
> -
> -- reset-gpios: GPIO to be used to reset the whole device
> -- reset-duration: reset duration in milliseconds, defaults to 200 ms
> -
> -Subnodes:
> -
> -The integrated switch subnode should be specified according to the binding
> -described in dsa/dsa.txt. The CPU port of this switch is always port 0.
> -
> -Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is
> -configured to use 1/2/3 instead. This hardware configuration will be
> -auto-detected and mapped accordingly.
> -
> -Example:
> -
> -I2C managed mode:
> -
> - master: masterdevice@X {
> -
> - fixed-link { /* RMII fixed link to LAN9303 */
> - speed = <100>;
> - full-duplex;
> - };
> - };
> -
> - switch: switch@a {
> - compatible = "smsc,lan9303-i2c";
> - reg = <0xa>;
> - reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
> - reset-duration = <200>;
> -
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - port@0 { /* RMII fixed link to master */
> - reg = <0>;
> - ethernet = <&master>;
> - };
> -
> - port@1 { /* external port 1 */
> - reg = <1>;
> - label = "lan1";
> - };
> -
> - port@2 { /* external port 2 */
> - reg = <2>;
> - label = "lan2";
> - };
> - };
> - };
> -
> -MDIO managed mode:
> -
> - master: masterdevice@X {
> - phy-handle = <&switch>;
> -
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - switch: switch-phy@0 {
> - compatible = "smsc,lan9303-mdio";
> - reg = <0>;
> - reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
> - reset-duration = <100>;
> -
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - port@0 {
> - reg = <0>;
> - ethernet = <&master>;
> - };
> -
> - port@1 { /* external port 1 */
> - reg = <1>;
> - label = "lan1";
> - };
> -
> - port@2 { /* external port 2 */
> - reg = <2>;
> - label = "lan2";
> - };
> - };
> - };
> - };
> - };
> +See Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml for the
> +device tree documentation covering the LAN9303 and LAN9354 devices.
No, just remove it.
> diff --git a/Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml b/Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml
> new file mode 100644
> index 000000000000..818770092a2c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/dsa/microchip,lan9303.yaml
> @@ -0,0 +1,129 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/dsa/microchip,lan9303.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: LAN9303 Ethernet Switch Series Tree Bindings
Drop "Tree Bindings"
> +
> +allOf:
> + - $ref: "dsa.yaml#"
Drop quotes.
> +
> +maintainers:
> + - UNGLinuxDriver@microchip.com
> +
> +properties:
> + compatible:
> + oneOf:
> + - enum:
> + - smsc,lan9303-mdio
> + - microchip,lan9354-mdio
> + - enum:
> + - smsc,lan9303-i2c
oneOf does not make sense. It's just one enum.
> +
> + reg:
> + maxItems: 1
> +
> + reset-gpios:
> + description: Optional gpio specifier for a reset line
Drop "gpio specifier for a"
> + maxItems: 1
> +
> + reset-duration:
> + description: Reset duration in milliseconds, defaults to 200 ms
This does not look like standard type or unit suffix, so you need here
type. Don't you have warnings for this?
default: 200
> +
> +required:
> + - compatible
> + - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> +
> + //Ethernet switch connected via mdio to the host
Missing space before comments. Use Linux style comments, not your own.
> + ethernet0 {
Drop "0".
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy-handle = <&lan9303switch>;
> + phy-mode = "rmii";
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + lan9303switch: switch@0 {
> + compatible = "smsc,lan9303-mdio";
> + dsa,member = <0 0>;
> + reg = <0>;
reg goes after compatible.
> + ethernet-ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port@0 {
> + reg = <0>;
> + phy-mode = "rmii";
> + ethernet = <ðernet>;
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> + };
> + port@1 {
> + reg = <1>;
> + max-speed = <100>;
> + label = "lan1";
> + };
> + port@2 {
> + reg = <2>;
> + max-speed = <100>;
> + label = "lan2";
> + };
> + };
> + };
> + };
> + };
> +
> + //Ethernet switch connected via i2c to the host
> + ethernet1 {
Just ethernet (and make it a second example)
Best regards,
Krzysztof
© 2016 - 2024 Red Hat, Inc.