From: Xinlei Lee <xinlei.lee@mediatek.com>

Dpi output needs to adjust the output format to dual edge for MT8186.

Co-developed-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index 508a6d994e83..b9d740efdb6a 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -14,6 +14,7 @@
 #include <linux/of_graph.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
+#include <linux/soc/mediatek/mtk-mmsys.h>
 #include <linux/types.h>
 
 #include <video/videomode.h>
@@ -29,6 +30,7 @@
 #include "mtk_disp_drv.h"
 #include "mtk_dpi_regs.h"
 #include "mtk_drm_ddp_comp.h"
+#include "mtk_drm_drv.h"
 
 enum mtk_dpi_out_bit_num {
 	MTK_DPI_OUT_BIT_NUM_8BITS,
@@ -66,6 +68,7 @@ struct mtk_dpi {
 	struct drm_connector *connector;
 	void __iomem *regs;
 	struct device *dev;
+	struct device *mmsys_dev;
 	struct clk *engine_clk;
 	struct clk *pixel_clk;
 	struct clk *tvd_clk;
@@ -134,6 +137,7 @@ struct mtk_dpi_yc_limit {
  * @yuv422_en_bit: Enable bit of yuv422.
  * @csc_enable_bit: Enable bit of CSC.
  * @pixels_per_iter: Quantity of transferred pixels per iteration.
+ * @edge_cfg_in_mmsys: If the edge configuration for DPI's output needs to be set in MMSYS.
  */
 struct mtk_dpi_conf {
 	unsigned int (*cal_factor)(int clock);
@@ -152,6 +156,7 @@ struct mtk_dpi_conf {
 	u32 yuv422_en_bit;
 	u32 csc_enable_bit;
 	u32 pixels_per_iter;
+	bool edge_cfg_in_mmsys;
 };
 
 static void mtk_dpi_mask(struct mtk_dpi *dpi, u32 offset, u32 val, u32 mask)
@@ -448,8 +453,12 @@ static void mtk_dpi_dual_edge(struct mtk_dpi *dpi)
 		mtk_dpi_mask(dpi, DPI_OUTPUT_SETTING,
 			     dpi->output_fmt == MEDIA_BUS_FMT_RGB888_2X12_LE ?
 			     EDGE_SEL : 0, EDGE_SEL);
+		if (dpi->conf->edge_cfg_in_mmsys)
+			mtk_mmsys_ddp_dpi_fmt_config(dpi->mmsys_dev, MTK_DPI_RGB888_DDR_CON);
 	} else {
 		mtk_dpi_mask(dpi, DPI_DDR_SETTING, DDR_EN | DDR_4PHASE, 0);
+		if (dpi->conf->edge_cfg_in_mmsys)
+			mtk_mmsys_ddp_dpi_fmt_config(dpi->mmsys_dev, MTK_DPI_RGB888_SDR_CON);
 	}
 }
 
@@ -777,8 +786,10 @@ static int mtk_dpi_bind(struct device *dev, struct device *master, void *data)
 {
 	struct mtk_dpi *dpi = dev_get_drvdata(dev);
 	struct drm_device *drm_dev = data;
+	struct mtk_drm_private *priv = drm_dev->dev_private;
 	int ret;
 
+	dpi->mmsys_dev = priv->mmsys_dev;
 	ret = drm_simple_encoder_init(drm_dev, &dpi->encoder,
 				      DRM_MODE_ENCODER_TMDS);
 	if (ret) {
-- 
2.18.0

On Wed, Oct 19, 2022 at 10:52:15AM +0800, xinlei.lee@mediatek.com wrote:
[..]
> @@ -134,6 +137,7 @@ struct mtk_dpi_yc_limit {
>   * @yuv422_en_bit: Enable bit of yuv422.
>   * @csc_enable_bit: Enable bit of CSC.
>   * @pixels_per_iter: Quantity of transferred pixels per iteration.
> + * @edge_cfg_in_mmsys: If the edge configuration for DPI's output needs to be set in MMSYS.

As Angelo suggested previously, this could be written slightly shorter as 

  * @edge_cfg_in_mmsys: Edge configuration for DPI output has to be set in MMSYS.

>   */
[..]
> @@ -448,8 +453,12 @@ static void mtk_dpi_dual_edge(struct mtk_dpi *dpi)
>  		mtk_dpi_mask(dpi, DPI_OUTPUT_SETTING,
>  			     dpi->output_fmt == MEDIA_BUS_FMT_RGB888_2X12_LE ?
>  			     EDGE_SEL : 0, EDGE_SEL);
> +		if (dpi->conf->edge_cfg_in_mmsys)
> +			mtk_mmsys_ddp_dpi_fmt_config(dpi->mmsys_dev, MTK_DPI_RGB888_DDR_CON);
>  	} else {
>  		mtk_dpi_mask(dpi, DPI_DDR_SETTING, DDR_EN | DDR_4PHASE, 0);
> +		if (dpi->conf->edge_cfg_in_mmsys)
> +			mtk_mmsys_ddp_dpi_fmt_config(dpi->mmsys_dev, MTK_DPI_RGB888_SDR_CON);

I know this isn't one of the formats supported by MT8186, but since we're using
platform-agnostic formats now... This else branch in theory could also run for a
format like MEDIA_BUS_FMT_YUYV8_1X16. Would it make sense to set
MTK_DPI_RGB888_SDR_CON in that case?

Thanks,
Nícolas

>  	}
[..]

Il 19/10/22 04:52, xinlei.lee@mediatek.com ha scritto:
> From: Xinlei Lee <xinlei.lee@mediatek.com>
> 
> Dpi output needs to adjust the output format to dual edge for MT8186.
> 
> Co-developed-by: Jitao Shi <jitao.shi@mediatek.com>
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
> Reviewed-by: CK Hu <ck.hu@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>