hw/misc/bcm2835_property.c | 314 +++++++++++++++++++++----- include/hw/arm/raspi_platform.h | 5 + include/hw/misc/raspberrypi-fw-defs.h | 169 ++++++++++++++ 3 files changed, 431 insertions(+), 57 deletions(-) create mode 100644 include/hw/misc/raspberrypi-fw-defs.h
Hello!
Sorry for a quite a big patch, but most of the changes are the same type.
Most of the patch is about a definition of new constants/structs and replacing
magic numbers with those constants.
Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
---
hw/misc/bcm2835_property.c | 314 +++++++++++++++++++++-----
include/hw/arm/raspi_platform.h | 5 +
include/hw/misc/raspberrypi-fw-defs.h | 169 ++++++++++++++
3 files changed, 431 insertions(+), 57 deletions(-)
create mode 100644 include/hw/misc/raspberrypi-fw-defs.h
diff --git a/hw/misc/bcm2835_property.c b/hw/misc/bcm2835_property.c
index 251b3d865d..70a8ed0a8c 100644
--- a/hw/misc/bcm2835_property.c
+++ b/hw/misc/bcm2835_property.c
@@ -12,10 +12,56 @@
#include "migration/vmstate.h"
#include "hw/irq.h"
#include "hw/misc/bcm2835_mbox_defs.h"
+#include "hw/misc/raspberrypi-fw-defs.h"
#include "sysemu/dma.h"
#include "qemu/log.h"
#include "qemu/module.h"
#include "trace.h"
+#include "hw/arm/raspi_platform.h"
+
+#define RPI_EXP_GPIO_BASE 128
+#define VC4_GPIO_EXPANDER_COUNT 8
+
+struct vc4_display_settings_t {
+ uint32_t display_num;
+ uint32_t width;
+ uint32_t height;
+ uint32_t depth;
+ uint16_t pitch;
+ uint32_t virtual_width;
+ uint32_t virtual_height;
+ uint16_t virtual_width_offset;
+ uint32_t virtual_height_offset;
+ unsigned long fb_bus_address;
+} QEMU_PACKED;
+
+enum rpi_firmware_clk_id {
+ RPI_FIRMWARE_EMMC_CLK_ID = 1,
+ RPI_FIRMWARE_UART_CLK_ID,
+ RPI_FIRMWARE_ARM_CLK_ID,
+ RPI_FIRMWARE_CORE_CLK_ID,
+ RPI_FIRMWARE_V3D_CLK_ID,
+ RPI_FIRMWARE_H264_CLK_ID,
+ RPI_FIRMWARE_ISP_CLK_ID,
+ RPI_FIRMWARE_SDRAM_CLK_ID,
+ RPI_FIRMWARE_PIXEL_CLK_ID,
+ RPI_FIRMWARE_PWM_CLK_ID,
+ RPI_FIRMWARE_HEVC_CLK_ID,
+ RPI_FIRMWARE_EMMC2_CLK_ID,
+ RPI_FIRMWARE_M2MC_CLK_ID,
+ RPI_FIRMWARE_PIXEL_BVB_CLK_ID,
+ RPI_FIRMWARE_VEC_CLK_ID,
+ RPI_FIRMWARE_NUM_CLK_ID,
+};
+
+struct vc4_gpio_expander_t {
+ uint32_t direction;
+ uint32_t polarity;
+ uint32_t term_en;
+ uint32_t term_pull_up;
+ uint32_t state;
+} vc4_gpio_expander[VC4_GPIO_EXPANDER_COUNT];
+
/* https://github.com/raspberrypi/firmware/wiki/Mailbox-property-interface */
@@ -28,6 +74,7 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
uint32_t tmp;
int n;
uint32_t offset, length, color;
+ uint32_t gpio_num;
/*
* Copy the current state of the framebuffer config; we will update
@@ -51,48 +98,48 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
/* @(value + 8) : Request/response indicator */
resplen = 0;
switch (tag) {
- case 0x00000000: /* End tag */
+ case RPI_FWREQ_PROPERTY_END: /* End tag */
break;
- case 0x00000001: /* Get firmware revision */
+ case RPI_FWREQ_GET_FIRMWARE_REVISION: /* Get firmware revision */
stl_le_phys(&s->dma_as, value + 12, 346337);
resplen = 4;
break;
- case 0x00010001: /* Get board model */
+ case RPI_FWREQ_GET_BOARD_MODEL: /* Get board model */
qemu_log_mask(LOG_UNIMP,
"bcm2835_property: 0x%08x get board model NYI\n",
tag);
resplen = 4;
break;
- case 0x00010002: /* Get board revision */
+ case RPI_FWREQ_GET_BOARD_REVISION: /* Get board revision */
stl_le_phys(&s->dma_as, value + 12, s->board_rev);
resplen = 4;
break;
- case 0x00010003: /* Get board MAC address */
+ case RPI_FWREQ_GET_BOARD_MAC_ADDRESS: /* Get board MAC address */
resplen = sizeof(s->macaddr.a);
dma_memory_write(&s->dma_as, value + 12, s->macaddr.a, resplen,
MEMTXATTRS_UNSPECIFIED);
break;
- case 0x00010004: /* Get board serial */
+ case RPI_FWREQ_GET_BOARD_SERIAL: /* Get board serial */
qemu_log_mask(LOG_UNIMP,
"bcm2835_property: 0x%08x get board serial NYI\n",
tag);
resplen = 8;
break;
- case 0x00010005: /* Get ARM memory */
+ case RPI_FWREQ_GET_ARM_MEMORY: /* Get ARM memory */
/* base */
stl_le_phys(&s->dma_as, value + 12, 0);
/* size */
stl_le_phys(&s->dma_as, value + 16, s->fbdev->vcram_base);
resplen = 8;
break;
- case 0x00010006: /* Get VC memory */
+ case RPI_FWREQ_GET_VC_MEMORY: /* Get VC memory */
/* base */
stl_le_phys(&s->dma_as, value + 12, s->fbdev->vcram_base);
/* size */
stl_le_phys(&s->dma_as, value + 16, s->fbdev->vcram_size);
resplen = 8;
break;
- case 0x00028001: /* Set power state */
+ case RPI_FWREQ_SET_POWER_STATE: /* Set power state */
/* Assume that whatever device they asked for exists,
* and we'll just claim we set it to the desired state
*/
@@ -102,39 +149,49 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
break;
/* Clocks */
-
- case 0x00030001: /* Get clock state */
+ case RPI_FWREQ_GET_CLOCK_STATE: /* Get clock state */
stl_le_phys(&s->dma_as, value + 16, 0x1);
resplen = 8;
break;
- case 0x00038001: /* Set clock state */
+ case RPI_FWREQ_SET_CLOCK_STATE: /* Set clock state */
qemu_log_mask(LOG_UNIMP,
"bcm2835_property: 0x%08x set clock state NYI\n",
tag);
resplen = 8;
break;
- case 0x00030002: /* Get clock rate */
- case 0x00030004: /* Get max clock rate */
- case 0x00030007: /* Get min clock rate */
+ case RPI_FWREQ_GET_CLOCK_RATE: /* Get clock rate */
+ case RPI_FWREQ_GET_MAX_CLOCK_RATE: /* Get max clock rate */
+ case RPI_FWREQ_GET_MIN_CLOCK_RATE: /* Get min clock rate */
switch (ldl_le_phys(&s->dma_as, value + 12)) {
- case 1: /* EMMC */
- stl_le_phys(&s->dma_as, value + 16, 50000000);
+ case RPI_FIRMWARE_EMMC_CLK_ID: /* EMMC */
+ stl_le_phys(&s->dma_as, value + 16, RPI_FIRMWARE_EMMC_CLK_RATE);
+ break;
+ case RPI_FIRMWARE_UART_CLK_ID: /* UART */
+ stl_le_phys(&s->dma_as, value + 16, RPI_FIRMWARE_UART_CLK_RATE);
break;
- case 2: /* UART */
- stl_le_phys(&s->dma_as, value + 16, 3000000);
+ case RPI_FIRMWARE_CORE_CLK_ID: /* Core Clock */
+ stl_le_phys(&s->dma_as, value + 16, RPI_FIRMWARE_CORE_CLK_RATE);
break;
default:
- stl_le_phys(&s->dma_as, value + 16, 700000000);
+ stl_le_phys(&s->dma_as, value + 16,
+ RPI_FIRMWARE_DEFAULT_CLK_RATE);
break;
}
resplen = 8;
break;
- case 0x00038002: /* Set clock rate */
- case 0x00038004: /* Set max clock rate */
- case 0x00038007: /* Set min clock rate */
+ case RPI_FWREQ_GET_CLOCKS: /* Get clocks */
+ /* TODO: add more clock IDs if needed */
+ stl_le_phys(&s->dma_as, value + 12, 0);
+ stl_le_phys(&s->dma_as, value + 16, RPI_FIRMWARE_ARM_CLK_ID);
+ resplen = 8;
+ break;
+
+ case RPI_FWREQ_SET_CLOCK_RATE: /* Set clock rate */
+ case RPI_FWREQ_SET_MAX_CLOCK_RATE: /* Set max clock rate */
+ case RPI_FWREQ_SET_MIN_CLOCK_RATE: /* Set min clock rate */
qemu_log_mask(LOG_UNIMP,
"bcm2835_property: 0x%08x set clock rate NYI\n",
tag);
@@ -142,122 +199,126 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
break;
/* Temperature */
-
- case 0x00030006: /* Get temperature */
+ case RPI_FWREQ_GET_TEMPERATURE: /* Get temperature */
stl_le_phys(&s->dma_as, value + 16, 25000);
resplen = 8;
break;
-
- case 0x0003000A: /* Get max temperature */
+ case RPI_FWREQ_GET_MAX_TEMPERATURE: /* Get max temperature */
stl_le_phys(&s->dma_as, value + 16, 99000);
resplen = 8;
break;
/* Frame buffer */
-
- case 0x00040001: /* Allocate buffer */
+ case RPI_FWREQ_FRAMEBUFFER_ALLOCATE: /* Allocate buffer */
stl_le_phys(&s->dma_as, value + 12, fbconfig.base);
stl_le_phys(&s->dma_as, value + 16,
bcm2835_fb_get_size(&fbconfig));
resplen = 8;
break;
- case 0x00048001: /* Release buffer */
+ case RPI_FWREQ_FRAMEBUFFER_RELEASE: /* Release buffer */
resplen = 0;
break;
- case 0x00040002: /* Blank screen */
+ case RPI_FWREQ_FRAMEBUFFER_BLANK: /* Blank screen */
resplen = 4;
break;
- case 0x00044003: /* Test physical display width/height */
- case 0x00044004: /* Test virtual display width/height */
+ /* Test physical display width/height */
+ case RPI_FWREQ_FRAMEBUFFER_TEST_PHYSICAL_WIDTH_HEIGHT:
+ /* Test virtual display width/height */
+ case RPI_FWREQ_FRAMEBUFFER_TEST_VIRTUAL_WIDTH_HEIGHT:
resplen = 8;
break;
- case 0x00048003: /* Set physical display width/height */
+ /* Set physical display width/height */
+ case RPI_FWREQ_FRAMEBUFFER_SET_PHYSICAL_WIDTH_HEIGHT:
fbconfig.xres = ldl_le_phys(&s->dma_as, value + 12);
fbconfig.yres = ldl_le_phys(&s->dma_as, value + 16);
bcm2835_fb_validate_config(&fbconfig);
fbconfig_updated = true;
/* fall through */
- case 0x00040003: /* Get physical display width/height */
+ /* Get physical display width/height */
+ case RPI_FWREQ_FRAMEBUFFER_GET_PHYSICAL_WIDTH_HEIGHT:
stl_le_phys(&s->dma_as, value + 12, fbconfig.xres);
stl_le_phys(&s->dma_as, value + 16, fbconfig.yres);
resplen = 8;
break;
- case 0x00048004: /* Set virtual display width/height */
+ /* Set virtual display width/height */
+ case RPI_FWREQ_FRAMEBUFFER_SET_VIRTUAL_WIDTH_HEIGHT:
fbconfig.xres_virtual = ldl_le_phys(&s->dma_as, value + 12);
fbconfig.yres_virtual = ldl_le_phys(&s->dma_as, value + 16);
bcm2835_fb_validate_config(&fbconfig);
fbconfig_updated = true;
/* fall through */
- case 0x00040004: /* Get virtual display width/height */
+ /* Get virtual display width/height */
+ case RPI_FWREQ_FRAMEBUFFER_GET_VIRTUAL_WIDTH_HEIGHT:
stl_le_phys(&s->dma_as, value + 12, fbconfig.xres_virtual);
stl_le_phys(&s->dma_as, value + 16, fbconfig.yres_virtual);
resplen = 8;
break;
- case 0x00044005: /* Test depth */
+ case RPI_FWREQ_FRAMEBUFFER_TEST_DEPTH: /* Test depth */
resplen = 4;
break;
- case 0x00048005: /* Set depth */
+ case RPI_FWREQ_FRAMEBUFFER_SET_DEPTH: /* Set depth */
fbconfig.bpp = ldl_le_phys(&s->dma_as, value + 12);
bcm2835_fb_validate_config(&fbconfig);
fbconfig_updated = true;
/* fall through */
- case 0x00040005: /* Get depth */
+ case RPI_FWREQ_FRAMEBUFFER_GET_DEPTH: /* Get depth */
stl_le_phys(&s->dma_as, value + 12, fbconfig.bpp);
resplen = 4;
break;
- case 0x00044006: /* Test pixel order */
+ case RPI_FWREQ_FRAMEBUFFER_TEST_PIXEL_ORDER: /* Test pixel order */
resplen = 4;
break;
- case 0x00048006: /* Set pixel order */
+ case RPI_FWREQ_FRAMEBUFFER_SET_PIXEL_ORDER: /* Set pixel order */
fbconfig.pixo = ldl_le_phys(&s->dma_as, value + 12);
bcm2835_fb_validate_config(&fbconfig);
fbconfig_updated = true;
/* fall through */
- case 0x00040006: /* Get pixel order */
+ case RPI_FWREQ_FRAMEBUFFER_GET_PIXEL_ORDER: /* Get pixel order */
stl_le_phys(&s->dma_as, value + 12, fbconfig.pixo);
resplen = 4;
break;
- case 0x00044007: /* Test pixel alpha */
+ case RPI_FWREQ_FRAMEBUFFER_TEST_ALPHA_MODE: /* Test pixel alpha */
resplen = 4;
break;
- case 0x00048007: /* Set alpha */
+ case RPI_FWREQ_FRAMEBUFFER_SET_ALPHA_MODE: /* Set alpha */
fbconfig.alpha = ldl_le_phys(&s->dma_as, value + 12);
bcm2835_fb_validate_config(&fbconfig);
fbconfig_updated = true;
/* fall through */
- case 0x00040007: /* Get alpha */
+ case RPI_FWREQ_FRAMEBUFFER_GET_ALPHA_MODE: /* Get alpha */
stl_le_phys(&s->dma_as, value + 12, fbconfig.alpha);
resplen = 4;
break;
- case 0x00040008: /* Get pitch */
+ case RPI_FWREQ_FRAMEBUFFER_GET_PITCH: /* Get pitch */
stl_le_phys(&s->dma_as, value + 12,
bcm2835_fb_get_pitch(&fbconfig));
resplen = 4;
break;
- case 0x00044009: /* Test virtual offset */
+ /* Test virtual offset */
+ case RPI_FWREQ_FRAMEBUFFER_TEST_VIRTUAL_OFFSET:
resplen = 8;
break;
- case 0x00048009: /* Set virtual offset */
+ case RPI_FWREQ_FRAMEBUFFER_SET_VIRTUAL_OFFSET: /* Set virtual offset */
fbconfig.xoffset = ldl_le_phys(&s->dma_as, value + 12);
fbconfig.yoffset = ldl_le_phys(&s->dma_as, value + 16);
bcm2835_fb_validate_config(&fbconfig);
fbconfig_updated = true;
/* fall through */
- case 0x00040009: /* Get virtual offset */
+ case RPI_FWREQ_FRAMEBUFFER_GET_VIRTUAL_OFFSET: /* Get virtual offset */
stl_le_phys(&s->dma_as, value + 12, fbconfig.xoffset);
stl_le_phys(&s->dma_as, value + 16, fbconfig.yoffset);
resplen = 8;
break;
- case 0x0004000a: /* Get/Test/Set overscan */
- case 0x0004400a:
- case 0x0004800a:
+ case RPI_FWREQ_FRAMEBUFFER_GET_OVERSCAN: /* Get/Test/Set overscan */
+ case RPI_FWREQ_FRAMEBUFFER_TEST_OVERSCAN:
+ case RPI_FWREQ_FRAMEBUFFER_SET_OVERSCAN:
stl_le_phys(&s->dma_as, value + 12, 0);
stl_le_phys(&s->dma_as, value + 16, 0);
stl_le_phys(&s->dma_as, value + 20, 0);
stl_le_phys(&s->dma_as, value + 24, 0);
resplen = 16;
break;
- case 0x0004800b: /* Set palette */
+ case RPI_FWREQ_FRAMEBUFFER_SET_PALETTE: /* Set palette */
offset = ldl_le_phys(&s->dma_as, value + 12);
length = ldl_le_phys(&s->dma_as, value + 16);
n = 0;
@@ -270,18 +331,19 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
stl_le_phys(&s->dma_as, value + 12, 0);
resplen = 4;
break;
- case 0x00040013: /* Get number of displays */
+
+ case RPI_FWREQ_FRAMEBUFFER_GET_NUM_DISPLAYS: /* Get num of displays */
stl_le_phys(&s->dma_as, value + 12, 1);
resplen = 4;
break;
- case 0x00060001: /* Get DMA channels */
+ case RPI_FWREQ_GET_DMA_CHANNELS: /* Get DMA channels */
/* channels 2-5 */
stl_le_phys(&s->dma_as, value + 12, 0x003C);
resplen = 4;
break;
- case 0x00050001: /* Get command line */
+ case RPI_FWREQ_GET_COMMAND_LINE: /* Get command line */
/*
* We follow the firmware behaviour: no NUL terminator is
* written to the buffer, and if the buffer is too short
@@ -295,6 +357,144 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
resplen);
break;
+ case RPI_FWREQ_GET_THROTTLED: /* Get throttled */
+ stl_le_phys(&s->dma_as, value + 12, 0);
+ resplen = 4;
+ break;
+
+ /* Get display settings*/
+ case RPI_FWREQ_FRAMEBUFFER_GET_DISPLAY_SETTINGS:
+ stl_le_phys(&s->dma_as, value + 12, 0); /* display_num */
+ stl_le_phys(&s->dma_as, value + 16, 800); /* width */
+ stl_le_phys(&s->dma_as, value + 20, 600); /* height */
+ stl_le_phys(&s->dma_as, value + 24, 32); /* depth */
+ stl_le_phys(&s->dma_as, value + 28, 32); /* pitch */
+ stl_le_phys(&s->dma_as, value + 30, 0); /* virtual_width */
+ stl_le_phys(&s->dma_as, value + 34, 0); /* virtual_height */
+ stl_le_phys(&s->dma_as, value + 38, 0); /* virtual_width_offset */
+ stl_le_phys(&s->dma_as, value + 40, 0); /* virtual_height_offset */
+ stl_le_phys(&s->dma_as, value + 44, 0); /* fb_bus_address low */
+ stl_le_phys(&s->dma_as, value + 48, 0); /* fb_bus_address hi */
+ resplen = sizeof(struct vc4_display_settings_t);
+ break;
+
+ case RPI_FWREQ_FRAMEBUFFER_SET_PITCH: /* Set Pitch */
+ resplen = 0;
+ break;
+
+ case RPI_FWREQ_GET_GPIO_CONFIG:
+ if (ldl_le_phys(&s->dma_as, value + 12) < RPI_EXP_GPIO_BASE) {
+ qemu_log_mask(LOG_UNIMP, "RPI_FWREQ_GET_GPIO_CONFIG "
+ "not implemented for gpiochip0\n");
+ } else {
+ gpio_num = ldl_le_phys(&s->dma_as, value + 12)
+ - RPI_EXP_GPIO_BASE;
+
+ if (gpio_num < VC4_GPIO_EXPANDER_COUNT) {
+ stl_le_phys(&s->dma_as, value + 16,
+ vc4_gpio_expander[gpio_num].direction);
+ stl_le_phys(&s->dma_as, value + 20,
+ vc4_gpio_expander[gpio_num].polarity);
+ stl_le_phys(&s->dma_as, value + 24,
+ vc4_gpio_expander[gpio_num].term_en);
+ stl_le_phys(&s->dma_as, value + 28,
+ vc4_gpio_expander[gpio_num].term_pull_up);
+ /* must be equal 0 */
+ stl_le_phys(&s->dma_as, value + 12, 0);
+ resplen = 4 * 5;
+ } else {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "RPI_FWREQ_GET_GPIO_CONFIG "
+ "gpio num must be < %d",
+ RPI_EXP_GPIO_BASE + VC4_GPIO_EXPANDER_COUNT);
+ }
+ }
+ break;
+
+ case RPI_FWREQ_SET_GPIO_CONFIG:
+ if (ldl_le_phys(&s->dma_as, value + 12) < RPI_EXP_GPIO_BASE) {
+ qemu_log_mask(LOG_UNIMP, "RPI_FWREQ_SET_GPIO_CONFIG "
+ "not implemented for gpiochip0\n");
+ } else {
+ gpio_num = ldl_le_phys(&s->dma_as, value + 12)
+ - RPI_EXP_GPIO_BASE;
+
+ if (gpio_num < VC4_GPIO_EXPANDER_COUNT) {
+ vc4_gpio_expander[gpio_num].direction =
+ ldl_le_phys(&s->dma_as, value + 16);
+ vc4_gpio_expander[gpio_num].polarity =
+ ldl_le_phys(&s->dma_as, value + 20);
+ vc4_gpio_expander[gpio_num].term_en =
+ ldl_le_phys(&s->dma_as, value + 24);
+ vc4_gpio_expander[gpio_num].term_pull_up =
+ ldl_le_phys(&s->dma_as, value + 28);
+ vc4_gpio_expander[gpio_num].state =
+ ldl_le_phys(&s->dma_as, value + 32);
+ /* must be equal 0 */
+ stl_le_phys(&s->dma_as, value + 12, 0);
+ resplen = 4;
+ } else {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "RPI_FWREQ_SET_GPIO_CONFIG "
+ "gpio num must be < %d",
+ RPI_EXP_GPIO_BASE + VC4_GPIO_EXPANDER_COUNT);
+ }
+ }
+ break;
+
+ case RPI_FWREQ_GET_GPIO_STATE:
+ if (ldl_le_phys(&s->dma_as, value + 12) < RPI_EXP_GPIO_BASE) {
+ qemu_log_mask(LOG_UNIMP, "RPI_FWREQ_GET_GPIO_STATE "
+ "not implemented for gpiochip0\n");
+ } else {
+ gpio_num = ldl_le_phys(&s->dma_as, value + 12)
+ - RPI_EXP_GPIO_BASE;
+
+ if (gpio_num < VC4_GPIO_EXPANDER_COUNT) {
+ stl_le_phys(&s->dma_as, value + 16,
+ vc4_gpio_expander[gpio_num].state);
+ /* must be equal 0 */
+ stl_le_phys(&s->dma_as, value + 12, 0);
+ resplen = 8;
+ } else {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "RPI_FWREQ_GET_GPIO_STATE "
+ "gpio num must be < %d",
+ RPI_EXP_GPIO_BASE + VC4_GPIO_EXPANDER_COUNT);
+ }
+ }
+ break;
+
+ case RPI_FWREQ_SET_GPIO_STATE:
+ if (ldl_le_phys(&s->dma_as, value + 12) < RPI_EXP_GPIO_BASE) {
+ qemu_log_mask(LOG_UNIMP, "RPI_FWREQ_SET_GPIO_STATE not "
+ "implemented for gpiochip0\n");
+ } else {
+ gpio_num = ldl_le_phys(&s->dma_as, value + 12)
+ - RPI_EXP_GPIO_BASE;
+
+ if (gpio_num < VC4_GPIO_EXPANDER_COUNT) {
+ vc4_gpio_expander[gpio_num].state = ldl_le_phys(&s->dma_as,
+ value + 16);
+ /* must be equal 0 */
+ stl_le_phys(&s->dma_as, value + 12, 0);
+ resplen = 4;
+ } else {
+ qemu_log_mask(LOG_GUEST_ERROR,
+ "RPI_FWREQ_SET_GPIO_STATE "
+ "gpio num must be < %d",
+ RPI_EXP_GPIO_BASE + VC4_GPIO_EXPANDER_COUNT);
+ }
+ }
+ break;
+
+ case RPI_FWREQ_VCHIQ_INIT:
+ stl_le_phys(&s->dma_as,
+ value + offsetof(rpi_firmware_prop_request_t, payload),
+ 0);
+ resplen = VCHI_BUSADDR_SIZE;
+ break;
+
default:
qemu_log_mask(LOG_UNIMP,
"bcm2835_property: unhandled tag 0x%08x\n", tag);
diff --git a/include/hw/arm/raspi_platform.h b/include/hw/arm/raspi_platform.h
index 4a56dd4b89..9c34987c60 100644
--- a/include/hw/arm/raspi_platform.h
+++ b/include/hw/arm/raspi_platform.h
@@ -170,4 +170,9 @@
#define INTERRUPT_ILLEGAL_TYPE0 6
#define INTERRUPT_ILLEGAL_TYPE1 7
+#define RPI_FIRMWARE_EMMC_CLK_RATE 50000000
+#define RPI_FIRMWARE_UART_CLK_RATE 3000000
+#define RPI_FIRMWARE_CORE_CLK_RATE 350000000
+#define RPI_FIRMWARE_DEFAULT_CLK_RATE 700000000
+
#endif
diff --git a/include/hw/misc/raspberrypi-fw-defs.h b/include/hw/misc/raspberrypi-fw-defs.h
new file mode 100644
index 0000000000..2688e88522
--- /dev/null
+++ b/include/hw/misc/raspberrypi-fw-defs.h
@@ -0,0 +1,169 @@
+/*
+ * Raspberry Pi firmware definitions
+ *
+ * Copyright (C) 2022 Auriga LLC, based on Linux kernel
+ * `include/soc/bcm2835/raspberrypi-firmware.h` (Copyright © 2015 Broadcom)
+ *
+ * SPDX-License-Identifier: GPL-2.0-or-later
+ */
+
+#ifndef INCLUDE_HW_MISC_RASPBERRYPI_FW_DEFS_H_
+#define INCLUDE_HW_MISC_RASPBERRYPI_FW_DEFS_H_
+
+#include "qemu/osdep.h"
+
+enum rpi_firmware_property_tag {
+ RPI_FWREQ_PROPERTY_END = 0,
+ RPI_FWREQ_GET_FIRMWARE_REVISION = 0x00000001,
+ RPI_FWREQ_GET_FIRMWARE_VARIANT = 0x00000002,
+ RPI_FWREQ_GET_FIRMWARE_HASH = 0x00000003,
+
+ RPI_FWREQ_SET_CURSOR_INFO = 0x00008010,
+ RPI_FWREQ_SET_CURSOR_STATE = 0x00008011,
+
+ RPI_FWREQ_GET_BOARD_MODEL = 0x00010001,
+ RPI_FWREQ_GET_BOARD_REVISION = 0x00010002,
+ RPI_FWREQ_GET_BOARD_MAC_ADDRESS = 0x00010003,
+ RPI_FWREQ_GET_BOARD_SERIAL = 0x00010004,
+ RPI_FWREQ_GET_ARM_MEMORY = 0x00010005,
+ RPI_FWREQ_GET_VC_MEMORY = 0x00010006,
+ RPI_FWREQ_GET_CLOCKS = 0x00010007,
+ RPI_FWREQ_GET_POWER_STATE = 0x00020001,
+ RPI_FWREQ_GET_TIMING = 0x00020002,
+ RPI_FWREQ_SET_POWER_STATE = 0x00028001,
+ RPI_FWREQ_GET_CLOCK_STATE = 0x00030001,
+ RPI_FWREQ_GET_CLOCK_RATE = 0x00030002,
+ RPI_FWREQ_GET_VOLTAGE = 0x00030003,
+ RPI_FWREQ_GET_MAX_CLOCK_RATE = 0x00030004,
+ RPI_FWREQ_GET_MAX_VOLTAGE = 0x00030005,
+ RPI_FWREQ_GET_TEMPERATURE = 0x00030006,
+ RPI_FWREQ_GET_MIN_CLOCK_RATE = 0x00030007,
+ RPI_FWREQ_GET_MIN_VOLTAGE = 0x00030008,
+ RPI_FWREQ_GET_TURBO = 0x00030009,
+ RPI_FWREQ_GET_MAX_TEMPERATURE = 0x0003000a,
+ RPI_FWREQ_GET_STC = 0x0003000b,
+ RPI_FWREQ_ALLOCATE_MEMORY = 0x0003000c,
+ RPI_FWREQ_LOCK_MEMORY = 0x0003000d,
+ RPI_FWREQ_UNLOCK_MEMORY = 0x0003000e,
+ RPI_FWREQ_RELEASE_MEMORY = 0x0003000f,
+ RPI_FWREQ_EXECUTE_CODE = 0x00030010,
+ RPI_FWREQ_EXECUTE_QPU = 0x00030011,
+ RPI_FWREQ_SET_ENABLE_QPU = 0x00030012,
+ RPI_FWREQ_GET_DISPMANX_RESOURCE_MEM_HANDLE = 0x00030014,
+ RPI_FWREQ_GET_EDID_BLOCK = 0x00030020,
+ RPI_FWREQ_GET_CUSTOMER_OTP = 0x00030021,
+ RPI_FWREQ_GET_EDID_BLOCK_DISPLAY = 0x00030023,
+ RPI_FWREQ_GET_DOMAIN_STATE = 0x00030030,
+ RPI_FWREQ_GET_THROTTLED = 0x00030046,
+ RPI_FWREQ_GET_CLOCK_MEASURED = 0x00030047,
+ RPI_FWREQ_NOTIFY_REBOOT = 0x00030048,
+ RPI_FWREQ_SET_CLOCK_STATE = 0x00038001,
+ RPI_FWREQ_SET_CLOCK_RATE = 0x00038002,
+ RPI_FWREQ_SET_VOLTAGE = 0x00038003,
+ RPI_FWREQ_SET_MAX_CLOCK_RATE = 0x00038004,
+ RPI_FWREQ_SET_MIN_CLOCK_RATE = 0x00038007,
+ RPI_FWREQ_SET_TURBO = 0x00038009,
+ RPI_FWREQ_SET_CUSTOMER_OTP = 0x00038021,
+ RPI_FWREQ_SET_DOMAIN_STATE = 0x00038030,
+ RPI_FWREQ_GET_GPIO_STATE = 0x00030041,
+ RPI_FWREQ_SET_GPIO_STATE = 0x00038041,
+ RPI_FWREQ_SET_SDHOST_CLOCK = 0x00038042,
+ RPI_FWREQ_GET_GPIO_CONFIG = 0x00030043,
+ RPI_FWREQ_SET_GPIO_CONFIG = 0x00038043,
+ RPI_FWREQ_GET_PERIPH_REG = 0x00030045,
+ RPI_FWREQ_SET_PERIPH_REG = 0x00038045,
+ RPI_FWREQ_GET_POE_HAT_VAL = 0x00030049,
+ RPI_FWREQ_SET_POE_HAT_VAL = 0x00038049,
+ RPI_FWREQ_SET_POE_HAT_VAL_OLD = 0x00030050,
+ RPI_FWREQ_NOTIFY_XHCI_RESET = 0x00030058,
+ RPI_FWREQ_GET_REBOOT_FLAGS = 0x00030064,
+ RPI_FWREQ_SET_REBOOT_FLAGS = 0x00038064,
+ RPI_FWREQ_NOTIFY_DISPLAY_DONE = 0x00030066,
+
+ /* Dispmanx TAGS */
+ RPI_FWREQ_FRAMEBUFFER_ALLOCATE = 0x00040001,
+ RPI_FWREQ_FRAMEBUFFER_BLANK = 0x00040002,
+ RPI_FWREQ_FRAMEBUFFER_GET_PHYSICAL_WIDTH_HEIGHT = 0x00040003,
+ RPI_FWREQ_FRAMEBUFFER_GET_VIRTUAL_WIDTH_HEIGHT = 0x00040004,
+ RPI_FWREQ_FRAMEBUFFER_GET_DEPTH = 0x00040005,
+ RPI_FWREQ_FRAMEBUFFER_GET_PIXEL_ORDER = 0x00040006,
+ RPI_FWREQ_FRAMEBUFFER_GET_ALPHA_MODE = 0x00040007,
+ RPI_FWREQ_FRAMEBUFFER_GET_PITCH = 0x00040008,
+ RPI_FWREQ_FRAMEBUFFER_GET_VIRTUAL_OFFSET = 0x00040009,
+ RPI_FWREQ_FRAMEBUFFER_GET_OVERSCAN = 0x0004000a,
+ RPI_FWREQ_FRAMEBUFFER_GET_PALETTE = 0x0004000b,
+ RPI_FWREQ_FRAMEBUFFER_GET_LAYER = 0x0004000c,
+ RPI_FWREQ_FRAMEBUFFER_GET_TRANSFORM = 0x0004000d,
+ RPI_FWREQ_FRAMEBUFFER_GET_VSYNC = 0x0004000e,
+ RPI_FWREQ_FRAMEBUFFER_GET_TOUCHBUF = 0x0004000f,
+ RPI_FWREQ_FRAMEBUFFER_GET_GPIOVIRTBUF = 0x00040010,
+ RPI_FWREQ_FRAMEBUFFER_RELEASE = 0x00048001,
+ RPI_FWREQ_FRAMEBUFFER_GET_DISPLAY_ID = 0x00040016,
+ RPI_FWREQ_FRAMEBUFFER_SET_DISPLAY_NUM = 0x00048013,
+ RPI_FWREQ_FRAMEBUFFER_GET_NUM_DISPLAYS = 0x00040013,
+ RPI_FWREQ_FRAMEBUFFER_GET_DISPLAY_SETTINGS = 0x00040014,
+ RPI_FWREQ_FRAMEBUFFER_TEST_PHYSICAL_WIDTH_HEIGHT = 0x00044003,
+ RPI_FWREQ_FRAMEBUFFER_TEST_VIRTUAL_WIDTH_HEIGHT = 0x00044004,
+ RPI_FWREQ_FRAMEBUFFER_TEST_DEPTH = 0x00044005,
+ RPI_FWREQ_FRAMEBUFFER_TEST_PIXEL_ORDER = 0x00044006,
+ RPI_FWREQ_FRAMEBUFFER_TEST_ALPHA_MODE = 0x00044007,
+ RPI_FWREQ_FRAMEBUFFER_TEST_VIRTUAL_OFFSET = 0x00044009,
+ RPI_FWREQ_FRAMEBUFFER_TEST_OVERSCAN = 0x0004400a,
+ RPI_FWREQ_FRAMEBUFFER_TEST_PALETTE = 0x0004400b,
+ RPI_FWREQ_FRAMEBUFFER_TEST_LAYER = 0x0004400c,
+ RPI_FWREQ_FRAMEBUFFER_TEST_TRANSFORM = 0x0004400d,
+ RPI_FWREQ_FRAMEBUFFER_TEST_VSYNC = 0x0004400e,
+ RPI_FWREQ_FRAMEBUFFER_SET_PHYSICAL_WIDTH_HEIGHT = 0x00048003,
+ RPI_FWREQ_FRAMEBUFFER_SET_VIRTUAL_WIDTH_HEIGHT = 0x00048004,
+ RPI_FWREQ_FRAMEBUFFER_SET_DEPTH = 0x00048005,
+ RPI_FWREQ_FRAMEBUFFER_SET_PIXEL_ORDER = 0x00048006,
+ RPI_FWREQ_FRAMEBUFFER_SET_ALPHA_MODE = 0x00048007,
+ RPI_FWREQ_FRAMEBUFFER_SET_PITCH = 0x00048008,
+ RPI_FWREQ_FRAMEBUFFER_SET_VIRTUAL_OFFSET = 0x00048009,
+ RPI_FWREQ_FRAMEBUFFER_SET_OVERSCAN = 0x0004800a,
+ RPI_FWREQ_FRAMEBUFFER_SET_PALETTE = 0x0004800b,
+
+ RPI_FWREQ_FRAMEBUFFER_SET_TOUCHBUF = 0x0004801f,
+ RPI_FWREQ_FRAMEBUFFER_SET_GPIOVIRTBUF = 0x00048020,
+ RPI_FWREQ_FRAMEBUFFER_SET_VSYNC = 0x0004800e,
+ RPI_FWREQ_FRAMEBUFFER_SET_LAYER = 0x0004800c,
+ RPI_FWREQ_FRAMEBUFFER_SET_TRANSFORM = 0x0004800d,
+ RPI_FWREQ_FRAMEBUFFER_SET_BACKLIGHT = 0x0004800f,
+
+ RPI_FWREQ_VCHIQ_INIT = 0x00048010,
+
+ RPI_FWREQ_SET_PLANE = 0x00048015,
+ RPI_FWREQ_GET_DISPLAY_TIMING = 0x00040017,
+ RPI_FWREQ_SET_TIMING = 0x00048017,
+ RPI_FWREQ_GET_DISPLAY_CFG = 0x00040018,
+ RPI_FWREQ_SET_DISPLAY_POWER = 0x00048019,
+ RPI_FWREQ_GET_COMMAND_LINE = 0x00050001,
+ RPI_FWREQ_GET_DMA_CHANNELS = 0x00060001,
+};
+
+
+/**
+ * struct rpi_firmware_property_tag_header - Firmware property tag header
+ * @tag: One of enum_mbox_property_tag.
+ * @buf_size: The number of bytes in the value buffer following this
+ * struct.
+ * @req_resp_size: On submit, the length of the request (though it doesn't
+ * appear to be currently used by the firmware). On return,
+ * the length of the response (always 4 byte aligned), with
+ * the low bit set.
+ */
+struct rpi_firmware_property_tag_header {
+ uint32_t tag;
+ uint32_t buf_size;
+ uint32_t req_resp_size;
+};
+
+typedef struct rpi_firmware_prop_request {
+ struct rpi_firmware_property_tag_header hdr;
+ uint8_t payload[0];
+} rpi_firmware_prop_request_t;
+
+
+#define VCHI_BUSADDR_SIZE sizeof(uint32_t)
+
+#endif /* INCLUDE_HW_MISC_RASPBERRYPI_FW_DEFS_H_ */
--
2.34.1
On Wed, 24 May 2023 at 20:15, Sergey Kambalin <serg.oker@gmail.com> wrote:
>
> Hello!
> Sorry for a quite a big patch, but most of the changes are the same type.
> Most of the patch is about a definition of new constants/structs and replacing
> magic numbers with those constants.
>
>
> Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
> ---
> @@ -51,48 +98,48 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
> /* @(value + 8) : Request/response indicator */
> resplen = 0;
> switch (tag) {
> - case 0x00000000: /* End tag */
> + case RPI_FWREQ_PROPERTY_END: /* End tag */
> break;
> - case 0x00000001: /* Get firmware revision */
> + case RPI_FWREQ_GET_FIRMWARE_REVISION: /* Get firmware revision */
> stl_le_phys(&s->dma_as, value + 12, 346337);
> resplen = 4;
> break;
> - case 0x00010001: /* Get board model */
> + case RPI_FWREQ_GET_BOARD_MODEL: /* Get board model */
> qemu_log_mask(LOG_UNIMP,
> "bcm2835_property: 0x%08x get board model NYI\n",
> tag);
> resplen = 4;
> break;
> - case 0x00010002: /* Get board revision */
> + case RPI_FWREQ_GET_BOARD_REVISION: /* Get board revision */
So mostly this is just updating hardcoded constants to
symbolic constants, which is great.
> - case 0x00038002: /* Set clock rate */
> - case 0x00038004: /* Set max clock rate */
> - case 0x00038007: /* Set min clock rate */
> + case RPI_FWREQ_GET_CLOCKS: /* Get clocks */
> + /* TODO: add more clock IDs if needed */
> + stl_le_phys(&s->dma_as, value + 12, 0);
> + stl_le_phys(&s->dma_as, value + 16, RPI_FIRMWARE_ARM_CLK_ID);
> + resplen = 8;
> + break;
But this is adding a new implementation of a new property...
> +
> + case RPI_FWREQ_SET_CLOCK_RATE: /* Set clock rate */
> + case RPI_FWREQ_SET_MAX_CLOCK_RATE: /* Set max clock rate */
> + case RPI_FWREQ_SET_MIN_CLOCK_RATE: /* Set min clock rate */
> qemu_log_mask(LOG_UNIMP,
> "bcm2835_property: 0x%08x set clock rate NYI\n",
> tag);
> @@ -295,6 +357,144 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
> resplen);
> break;
>
> + case RPI_FWREQ_GET_THROTTLED: /* Get throttled */
> + stl_le_phys(&s->dma_as, value + 12, 0);
> + resplen = 4;
> + break;
...and this and the other bits further down in this part of
the patch are new properties too.
New features should be in separate patches from refactoring cleanup,
please.
By the way: when you split up patches you don't need to send them
just one at a time -- you can send a patchset of multiple related
patches.
thanks
-- PMM
Got it! Thanks!
I'll split this one to three patches:
1) replace magic numbers with named constants (refactoring)
2) add new properties for VC 4
3) Add some unit tests to check the newly added properties via mailbox
Is it OK?
(Sorry for wasting your time by inappropriate patches - this is my first experience with OSS)
________________________________
От: Peter Maydell <peter.maydell@linaro.org>
Отправлено: 30 мая 2023 г. 15:12:24
Кому: Sergey Kambalin
Копия: qemu-arm@nongnu.org; qemu-devel@nongnu.org; Kambalin, Sergey
Тема: Re: [PATCH] Prepare bcm properties for videocore 4
On Wed, 24 May 2023 at 20:15, Sergey Kambalin <serg.oker@gmail.com> wrote:
>
> Hello!
> Sorry for a quite a big patch, but most of the changes are the same type.
> Most of the patch is about a definition of new constants/structs and replacing
> magic numbers with those constants.
>
>
> Signed-off-by: Sergey Kambalin <sergey.kambalin@auriga.com>
> ---
> @@ -51,48 +98,48 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
> /* @(value + 8) : Request/response indicator */
> resplen = 0;
> switch (tag) {
> - case 0x00000000: /* End tag */
> + case RPI_FWREQ_PROPERTY_END: /* End tag */
> break;
> - case 0x00000001: /* Get firmware revision */
> + case RPI_FWREQ_GET_FIRMWARE_REVISION: /* Get firmware revision */
> stl_le_phys(&s->dma_as, value + 12, 346337);
> resplen = 4;
> break;
> - case 0x00010001: /* Get board model */
> + case RPI_FWREQ_GET_BOARD_MODEL: /* Get board model */
> qemu_log_mask(LOG_UNIMP,
> "bcm2835_property: 0x%08x get board model NYI\n",
> tag);
> resplen = 4;
> break;
> - case 0x00010002: /* Get board revision */
> + case RPI_FWREQ_GET_BOARD_REVISION: /* Get board revision */
So mostly this is just updating hardcoded constants to
symbolic constants, which is great.
> - case 0x00038002: /* Set clock rate */
> - case 0x00038004: /* Set max clock rate */
> - case 0x00038007: /* Set min clock rate */
> + case RPI_FWREQ_GET_CLOCKS: /* Get clocks */
> + /* TODO: add more clock IDs if needed */
> + stl_le_phys(&s->dma_as, value + 12, 0);
> + stl_le_phys(&s->dma_as, value + 16, RPI_FIRMWARE_ARM_CLK_ID);
> + resplen = 8;
> + break;
But this is adding a new implementation of a new property...
> +
> + case RPI_FWREQ_SET_CLOCK_RATE: /* Set clock rate */
> + case RPI_FWREQ_SET_MAX_CLOCK_RATE: /* Set max clock rate */
> + case RPI_FWREQ_SET_MIN_CLOCK_RATE: /* Set min clock rate */
> qemu_log_mask(LOG_UNIMP,
> "bcm2835_property: 0x%08x set clock rate NYI\n",
> tag);
> @@ -295,6 +357,144 @@ static void bcm2835_property_mbox_push(BCM2835PropertyState *s, uint32_t value)
> resplen);
> break;
>
> + case RPI_FWREQ_GET_THROTTLED: /* Get throttled */
> + stl_le_phys(&s->dma_as, value + 12, 0);
> + resplen = 4;
> + break;
...and this and the other bits further down in this part of
the patch are new properties too.
New features should be in separate patches from refactoring cleanup,
please.
By the way: when you split up patches you don't need to send them
just one at a time -- you can send a patchset of multiple related
patches.
thanks
-- PMM
On 30/5/23 15:00, Kambalin, Sergey wrote: > Got it! Thanks! > > I'll split this one to three patches: > 1) replace magic numbers with named constants (refactoring) > > 2) add new properties for VC 4 > > 3) Add some unit tests to check the newly added properties via mailbox > > > Is it OK? This looks good. Try to imagine sitting on the other side, where developers will review your code. Usually the simplest the better, even dumb patches, since there is no risk for doubt. Don't be afraid to post many small patches. Personally I'd do: - import Linux definitions - replace current magic values with imported Linux defs - add GET_CLOCKS property - add GET_THROTTLED property - add FRAMEBUFFER properties - add GPIO properties - add VCHIQ property Look at do_test_arm_raspi*() in tests/avocado/boot_linux_console.py, you could add newer kernels which use the properties you added. > (Sorry for wasting your time by inappropriate patches - this is my first > experience with OSS) So far you are doing great! Thanks, Phil.
Hello! Thank you guys for clarifications! > Are the VC4 properties supposed to be present on > all our existing raspi models? (i.e. is this a bug > fix for our existing models rather than stuff we only > want on the new raspi4b?) Yes, they're needed to support RPI4 work. And I think cannot be considered as a bug fix. So I'm going to send one patch to replace the magic values with named constants. And then I'm going to spend some time to slice the entire rpi4 machine to series of small patches. Am I understand it right that each patch in the set must pass all the tests? ________________________________ От: Philippe Mathieu-Daudé <philmd@linaro.org> Отправлено: 30 мая 2023 г. 17:02:00 Кому: Kambalin, Sergey; Peter Maydell; Sergey Kambalin Копия: qemu-arm@nongnu.org; qemu-devel@nongnu.org Тема: Re: [PATCH] Prepare bcm properties for videocore 4 On 30/5/23 15:00, Kambalin, Sergey wrote: > Got it! Thanks! > > I'll split this one to three patches: > 1) replace magic numbers with named constants (refactoring) > > 2) add new properties for VC 4 > > 3) Add some unit tests to check the newly added properties via mailbox > > > Is it OK? This looks good. Try to imagine sitting on the other side, where developers will review your code. Usually the simplest the better, even dumb patches, since there is no risk for doubt. Don't be afraid to post many small patches. Personally I'd do: - import Linux definitions - replace current magic values with imported Linux defs - add GET_CLOCKS property - add GET_THROTTLED property - add FRAMEBUFFER properties - add GPIO properties - add VCHIQ property Look at do_test_arm_raspi*() in tests/avocado/boot_linux_console.py, you could add newer kernels which use the properties you added. > (Sorry for wasting your time by inappropriate patches - this is my first > experience with OSS) So far you are doing great! Thanks, Phil.
On Wed, 31 May 2023 at 16:47, Kambalin, Sergey <sergey.kambalin@auriga.com> wrote: > > Hello! > > Thank you guys for clarifications! > > > > Are the VC4 properties supposed to be present on > > all our existing raspi models? (i.e. is this a bug > > fix for our existing models rather than stuff we only > > want on the new raspi4b?) > > > Yes, they're needed to support RPI4 work. And I think cannot be considered as a bug fix. > > So I'm going to send one patch to replace the magic values with named constants. > > And then I'm going to spend some time to slice the entire rpi4 machine to series of small patches. > > Am I understand it right that each patch in the set must pass all the tests? Yes, that's right -- every patch has to compile and pass 'make check'. The usual way to arrange this is "put the new tests last". thanks -- PMM
On Tue, 30 May 2023 at 14:00, Kambalin, Sergey <sergey.kambalin@auriga.com> wrote: > > Got it! Thanks! > > I'll split this one to three patches: > 1) replace magic numbers with named constants (refactoring) > > 2) add new properties for VC 4 > > 3) Add some unit tests to check the newly added properties via mailbox Are the VC4 properties supposed to be present on all our existing raspi models? (i.e. is this a bug fix for our existing models rather than stuff we only want on the new raspi4b?) As a rule of thumb, stuff fixing issues with our existing code can be sent in as its own patch or patchset; changes which are specifically for a new board/SoC should be put together into the patchset which adds that new board. > (Sorry for wasting your time by inappropriate patches - this is my first experience with OSS) No, that's fine -- the project's review/patch preferences are a bit confusing for people coming to it for the first time. thanks -- PMM
© 2016 - 2024 Red Hat, Inc.