ARM queue: mostly patches from me, but also the Smartfusion2 board. thanks -- PMM The following changes since commit 9ee660e7c138595224b65ddc1c5712549f0a278c: Merge remote-tracking branch 'remotes/yongbok/tags/mips-20170921' into staging (2017-09-21 14:40:32 +0100) are available in the git repository at: git://git.linaro.org/people/pmaydell/qemu-arm.git tags/pull-target-arm-20170921 for you to fetch changes up to 6d262dcb7d108eda93813574c2061398084dc795: msf2: Add Emcraft's Smartfusion2 SOM kit (2017-09-21 16:36:56 +0100) ---------------------------------------------------------------- target-arm queue: * more preparatory work for v8M support * convert some omap devices away from old_mmio * remove out of date ARM ARM section references in comments * add the Smartfusion2 board ---------------------------------------------------------------- Peter Maydell (26): target/arm: Implement MSR/MRS access to NS banked registers nvic: Add banked exception states nvic: Add cached vectpending_is_s_banked state nvic: Add cached vectpending_prio state nvic: Implement AIRCR changes for v8M nvic: Make ICSR.RETTOBASE handle banked exceptions nvic: Implement NVIC_ITNS<n> registers nvic: Handle banked exceptions in nvic_recompute_state() nvic: Make set_pending and clear_pending take a secure parameter nvic: Make SHPR registers banked nvic: Compare group priority for escalation to HF nvic: In escalation to HardFault, support HF not being priority -1 nvic: Implement v8M changes to fixed priority exceptions nvic: Disable the non-secure HardFault if AIRCR.BFHFNMINS is clear nvic: Handle v8M changes in nvic_exec_prio() target/arm: Handle banking in negative-execution-priority check in cpu_mmu_index() nvic: Make ICSR banked for v8M nvic: Make SHCSR banked for v8M nvic: Support banked exceptions in acknowledge and complete target/arm: Remove out of date ARM ARM section references in A64 decoder hw/arm/palm.c: Don't use old_mmio for static_ops hw/gpio/omap_gpio.c: Don't use old_mmio hw/timer/omap_synctimer.c: Don't use old_mmio hw/timer/omap_gptimer: Don't use old_mmio hw/i2c/omap_i2c.c: Don't use old_mmio hw/arm/omap2.c: Don't use old_mmio Subbaraya Sundeep (5): msf2: Add Smartfusion2 System timer msf2: Microsemi Smartfusion2 System Register block msf2: Add Smartfusion2 SPI controller msf2: Add Smartfusion2 SoC msf2: Add Emcraft's Smartfusion2 SOM kit hw/arm/Makefile.objs | 1 + hw/misc/Makefile.objs | 1 + hw/ssi/Makefile.objs | 1 + hw/timer/Makefile.objs | 1 + include/hw/arm/msf2-soc.h | 67 +++ include/hw/intc/armv7m_nvic.h | 33 +- include/hw/misc/msf2-sysreg.h | 77 ++++ include/hw/ssi/mss-spi.h | 58 +++ include/hw/timer/mss-timer.h | 64 +++ target/arm/cpu.h | 62 ++- hw/arm/msf2-soc.c | 238 +++++++++++ hw/arm/msf2-som.c | 105 +++++ hw/arm/omap2.c | 49 ++- hw/arm/palm.c | 30 +- hw/gpio/omap_gpio.c | 26 +- hw/i2c/omap_i2c.c | 44 +- hw/intc/armv7m_nvic.c | 913 ++++++++++++++++++++++++++++++++++------ hw/misc/msf2-sysreg.c | 160 +++++++ hw/ssi/mss-spi.c | 404 ++++++++++++++++++ hw/timer/mss-timer.c | 289 +++++++++++++ hw/timer/omap_gptimer.c | 49 ++- hw/timer/omap_synctimer.c | 35 +- target/arm/cpu.c | 7 + target/arm/helper.c | 142 ++++++- target/arm/translate-a64.c | 227 +++++----- default-configs/arm-softmmu.mak | 1 + hw/intc/trace-events | 13 +- hw/misc/trace-events | 5 + 28 files changed, 2735 insertions(+), 367 deletions(-) create mode 100644 include/hw/arm/msf2-soc.h create mode 100644 include/hw/misc/msf2-sysreg.h create mode 100644 include/hw/ssi/mss-spi.h create mode 100644 include/hw/timer/mss-timer.h create mode 100644 hw/arm/msf2-soc.c create mode 100644 hw/arm/msf2-som.c create mode 100644 hw/misc/msf2-sysreg.c create mode 100644 hw/ssi/mss-spi.c create mode 100644 hw/timer/mss-timer.c In v8M the MSR and MRS instructions have extra register value encodings to allow secure code to access the non-secure banked version of various special registers. (We don't implement the MSPLIM_NS or PSPLIM_NS aliases, because we don't currently implement the stack limit registers at all.) Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-2-git-send-email-peter.maydell@linaro.org --- target/arm/helper.c | 110 ++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 110 insertions(+) diff --git a/target/arm/helper.c b/target/arm/helper.c index XXXXXXX..XXXXXXX 100644 --- a/target/arm/helper.c +++ b/target/arm/helper.c @@ -XXX,XX +XXX,XX @@ uint32_t HELPER(v7m_mrs)(CPUARMState *env, uint32_t reg) break; case 20: /* CONTROL */ return env->v7m.control[env->v7m.secure]; + case 0x94: /* CONTROL_NS */ + /* We have to handle this here because unprivileged Secure code + * can read the NS CONTROL register. + */ + if (!env->v7m.secure) { + return 0; + } + return env->v7m.control[M_REG_NS]; } if (el == 0) { return 0; /* unprivileged reads others as zero */ } + if (arm_feature(env, ARM_FEATURE_M_SECURITY)) { + switch (reg) { + case 0x88: /* MSP_NS */ + if (!env->v7m.secure) { + return 0; + } + return env->v7m.other_ss_msp; + case 0x89: /* PSP_NS */ + if (!env->v7m.secure) { + return 0; + } + return env->v7m.other_ss_psp; + case 0x90: /* PRIMASK_NS */ + if (!env->v7m.secure) { + return 0; + } + return env->v7m.primask[M_REG_NS]; + case 0x91: /* BASEPRI_NS */ + if (!env->v7m.secure) { + return 0; + } + return env->v7m.basepri[M_REG_NS]; + case 0x93: /* FAULTMASK_NS */ + if (!env->v7m.secure) { + return 0; + } + return env->v7m.faultmask[M_REG_NS]; + case 0x98: /* SP_NS */ + { + /* This gives the non-secure SP selected based on whether we're + * currently in handler mode or not, using the NS CONTROL.SPSEL. + */ + bool spsel = env->v7m.control[M_REG_NS] & R_V7M_CONTROL_SPSEL_MASK; + + if (!env->v7m.secure) { + return 0; + } + if (!arm_v7m_is_handler_mode(env) && spsel) { + return env->v7m.other_ss_psp; + } else { + return env->v7m.other_ss_msp; + } + } + default: + break; + } + } + switch (reg) { case 8: /* MSP */ return (env->v7m.control[env->v7m.secure] & R_V7M_CONTROL_SPSEL_MASK) ? @@ -XXX,XX +XXX,XX @@ void HELPER(v7m_msr)(CPUARMState *env, uint32_t maskreg, uint32_t val) return; } + if (arm_feature(env, ARM_FEATURE_M_SECURITY)) { + switch (reg) { + case 0x88: /* MSP_NS */ + if (!env->v7m.secure) { + return; + } + env->v7m.other_ss_msp = val; + return; + case 0x89: /* PSP_NS */ + if (!env->v7m.secure) { + return; + } + env->v7m.other_ss_psp = val; + return; + case 0x90: /* PRIMASK_NS */ + if (!env->v7m.secure) { + return; + } + env->v7m.primask[M_REG_NS] = val & 1; + return; + case 0x91: /* BASEPRI_NS */ + if (!env->v7m.secure) { + return; + } + env->v7m.basepri[M_REG_NS] = val & 0xff; + return; + case 0x93: /* FAULTMASK_NS */ + if (!env->v7m.secure) { + return; + } + env->v7m.faultmask[M_REG_NS] = val & 1; + return; + case 0x98: /* SP_NS */ + { + /* This gives the non-secure SP selected based on whether we're + * currently in handler mode or not, using the NS CONTROL.SPSEL. + */ + bool spsel = env->v7m.control[M_REG_NS] & R_V7M_CONTROL_SPSEL_MASK; + + if (!env->v7m.secure) { + return; + } + if (!arm_v7m_is_handler_mode(env) && spsel) { + env->v7m.other_ss_psp = val; + } else { + env->v7m.other_ss_msp = val; + } + return; + } + default: + break; + } + } + switch (reg) { case 0 ... 7: /* xPSR sub-fields */ /* only APSR is actually writable */ -- 2.7.4 For the v8M security extension, some exceptions must be banked between security states. Add the new vecinfo array which holds the state for the banked exceptions and migrate it if the CPU the NVIC is attached to implements the security extension. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> --- include/hw/intc/armv7m_nvic.h | 14 ++++++++++++ hw/intc/armv7m_nvic.c | 53 ++++++++++++++++++++++++++++++++++++++++++- 2 files changed, 66 insertions(+), 1 deletion(-) diff --git a/include/hw/intc/armv7m_nvic.h b/include/hw/intc/armv7m_nvic.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/intc/armv7m_nvic.h +++ b/include/hw/intc/armv7m_nvic.h @@ -XXX,XX +XXX,XX @@ /* Highest permitted number of exceptions (architectural limit) */ #define NVIC_MAX_VECTORS 512 +/* Number of internal exceptions */ +#define NVIC_INTERNAL_VECTORS 16 typedef struct VecInfo { /* Exception priorities can range from -3 to 255; only the unmodifiable @@ -XXX,XX +XXX,XX @@ typedef struct NVICState { ARMCPU *cpu; VecInfo vectors[NVIC_MAX_VECTORS]; + /* If the v8M security extension is implemented, some of the internal + * exceptions are banked between security states (ie there exists both + * a Secure and a NonSecure version of the exception and its state): + * HardFault, MemManage, UsageFault, SVCall, PendSV, SysTick (R_PJHV) + * The rest (including all the external exceptions) are not banked, though + * they may be configurable to target either Secure or NonSecure state. + * We store the secure exception state in sec_vectors[] for the banked + * exceptions, and otherwise use only vectors[] (including for exceptions + * like SecureFault that unconditionally target Secure state). + * Entries in sec_vectors[] for non-banked exception numbers are unused. + */ + VecInfo sec_vectors[NVIC_INTERNAL_VECTORS]; uint32_t prigroup; /* vectpending and exception_prio are both cached state that can diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ * For historical reasons QEMU tends to use "interrupt" and * "exception" more or less interchangeably. */ -#define NVIC_FIRST_IRQ 16 +#define NVIC_FIRST_IRQ NVIC_INTERNAL_VECTORS #define NVIC_MAX_IRQ (NVIC_MAX_VECTORS - NVIC_FIRST_IRQ) /* Effective running priority of the CPU when no exception is active @@ -XXX,XX +XXX,XX @@ static const VMStateDescription vmstate_VecInfo = { } }; +static bool nvic_security_needed(void *opaque) +{ + NVICState *s = opaque; + + return arm_feature(&s->cpu->env, ARM_FEATURE_M_SECURITY); +} + +static int nvic_security_post_load(void *opaque, int version_id) +{ + NVICState *s = opaque; + int i; + + /* Check for out of range priority settings */ + if (s->sec_vectors[ARMV7M_EXCP_HARD].prio != -1) { + return 1; + } + for (i = ARMV7M_EXCP_MEM; i < ARRAY_SIZE(s->sec_vectors); i++) { + if (s->sec_vectors[i].prio & ~0xff) { + return 1; + } + } + return 0; +} + +static const VMStateDescription vmstate_nvic_security = { + .name = "nvic/m-security", + .version_id = 1, + .minimum_version_id = 1, + .needed = nvic_security_needed, + .post_load = &nvic_security_post_load, + .fields = (VMStateField[]) { + VMSTATE_STRUCT_ARRAY(sec_vectors, NVICState, NVIC_INTERNAL_VECTORS, 1, + vmstate_VecInfo, VecInfo), + VMSTATE_END_OF_LIST() + } +}; + static const VMStateDescription vmstate_nvic = { .name = "armv7m_nvic", .version_id = 4, @@ -XXX,XX +XXX,XX @@ static const VMStateDescription vmstate_nvic = { vmstate_VecInfo, VecInfo), VMSTATE_UINT32(prigroup, NVICState), VMSTATE_END_OF_LIST() + }, + .subsections = (const VMStateDescription*[]) { + &vmstate_nvic_security, + NULL } }; @@ -XXX,XX +XXX,XX @@ static void armv7m_nvic_reset(DeviceState *dev) s->vectors[ARMV7M_EXCP_NMI].prio = -2; s->vectors[ARMV7M_EXCP_HARD].prio = -1; + if (arm_feature(&s->cpu->env, ARM_FEATURE_M_SECURITY)) { + s->sec_vectors[ARMV7M_EXCP_HARD].enabled = 1; + s->sec_vectors[ARMV7M_EXCP_SVC].enabled = 1; + s->sec_vectors[ARMV7M_EXCP_PENDSV].enabled = 1; + s->sec_vectors[ARMV7M_EXCP_SYSTICK].enabled = 1; + + /* AIRCR.BFHFNMINS resets to 0 so Secure HF is priority -1 (R_CMTC) */ + s->sec_vectors[ARMV7M_EXCP_HARD].prio = -1; + } + /* Strictly speaking the reset handler should be enabled. * However, we don't simulate soft resets through the NVIC, * and the reset vector should never be pended. -- 2.7.4 With banked exceptions, just the exception number in s->vectpending is no longer sufficient to uniquely identify the pending exception. Add a vectpending_is_s_banked bool which is true if the exception is using the sec_vectors[] array. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 1505240046-11454-4-git-send-email-peter.maydell@linaro.org --- include/hw/intc/armv7m_nvic.h | 11 +++++++++-- hw/intc/armv7m_nvic.c | 1 + 2 files changed, 10 insertions(+), 2 deletions(-) diff --git a/include/hw/intc/armv7m_nvic.h b/include/hw/intc/armv7m_nvic.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/intc/armv7m_nvic.h +++ b/include/hw/intc/armv7m_nvic.h @@ -XXX,XX +XXX,XX @@ typedef struct NVICState { VecInfo sec_vectors[NVIC_INTERNAL_VECTORS]; uint32_t prigroup; - /* vectpending and exception_prio are both cached state that can - * be recalculated from the vectors[] array and the prigroup field. + /* The following fields are all cached state that can be recalculated + * from the vectors[] and sec_vectors[] arrays and the prigroup field: + * - vectpending + * - vectpending_is_secure + * - exception_prio */ unsigned int vectpending; /* highest prio pending enabled exception */ + /* true if vectpending is a banked secure exception, ie it is in + * sec_vectors[] rather than vectors[] + */ + bool vectpending_is_s_banked; int exception_prio; /* group prio of the highest prio active exception */ MemoryRegion sysregmem; diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static void armv7m_nvic_reset(DeviceState *dev) s->exception_prio = NVIC_NOEXC_PRIO; s->vectpending = 0; + s->vectpending_is_s_banked = false; } static void nvic_systick_trigger(void *opaque, int n, int level) -- 2.7.4 Instead of looking up the pending priority in nvic_pending_prio(), cache it in a new state struct field. The calculation of the pending priority given the interrupt number is more complicated in v8M with the security extension, so the caching will be worthwhile. This changes nvic_pending_prio() from returning a full (group + subpriority) priority value to returning a group priority. This doesn't require changes to its callsites because we use it only in comparisons of the form execution_prio > nvic_pending_prio() and execution priority is always a group priority, so a test (exec prio > full prio) is true if and only if (execprio > group_prio). (Architecturally the expected comparison is with the group priority for this sort of "would we preempt" test; we were only doing a test with a full priority as an optimisation to avoid the mask, which is possible precisely because the two comparisons always give the same answer.) Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-5-git-send-email-peter.maydell@linaro.org --- include/hw/intc/armv7m_nvic.h | 2 ++ hw/intc/armv7m_nvic.c | 23 +++++++++++++---------- hw/intc/trace-events | 2 +- 3 files changed, 16 insertions(+), 11 deletions(-) diff --git a/include/hw/intc/armv7m_nvic.h b/include/hw/intc/armv7m_nvic.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/intc/armv7m_nvic.h +++ b/include/hw/intc/armv7m_nvic.h @@ -XXX,XX +XXX,XX @@ typedef struct NVICState { * - vectpending * - vectpending_is_secure * - exception_prio + * - vectpending_prio */ unsigned int vectpending; /* highest prio pending enabled exception */ /* true if vectpending is a banked secure exception, ie it is in @@ -XXX,XX +XXX,XX @@ typedef struct NVICState { */ bool vectpending_is_s_banked; int exception_prio; /* group prio of the highest prio active exception */ + int vectpending_prio; /* group prio of the exeception in vectpending */ MemoryRegion sysregmem; MemoryRegion sysreg_ns_mem; diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static const uint8_t nvic_id[] = { static int nvic_pending_prio(NVICState *s) { - /* return the priority of the current pending interrupt, + /* return the group priority of the current pending interrupt, * or NVIC_NOEXC_PRIO if no interrupt is pending */ - return s->vectpending ? s->vectors[s->vectpending].prio : NVIC_NOEXC_PRIO; + return s->vectpending_prio; } /* Return the value of the ISCR RETTOBASE bit: @@ -XXX,XX +XXX,XX @@ static void nvic_recompute_state(NVICState *s) active_prio &= nvic_gprio_mask(s); } + if (pend_prio > 0) { + pend_prio &= nvic_gprio_mask(s); + } + s->vectpending = pend_irq; + s->vectpending_prio = pend_prio; s->exception_prio = active_prio; - trace_nvic_recompute_state(s->vectpending, s->exception_prio); + trace_nvic_recompute_state(s->vectpending, + s->vectpending_prio, + s->exception_prio); } /* Return the current execution priority of the CPU @@ -XXX,XX +XXX,XX @@ void armv7m_nvic_acknowledge_irq(void *opaque) CPUARMState *env = &s->cpu->env; const int pending = s->vectpending; const int running = nvic_exec_prio(s); - int pendgroupprio; VecInfo *vec; assert(pending > ARMV7M_EXCP_RESET && pending < s->num_irq); @@ -XXX,XX +XXX,XX @@ void armv7m_nvic_acknowledge_irq(void *opaque) assert(vec->enabled); assert(vec->pending); - pendgroupprio = vec->prio; - if (pendgroupprio > 0) { - pendgroupprio &= nvic_gprio_mask(s); - } - assert(pendgroupprio < running); + assert(s->vectpending_prio < running); - trace_nvic_acknowledge_irq(pending, vec->prio); + trace_nvic_acknowledge_irq(pending, s->vectpending_prio); vec->active = 1; vec->pending = 0; @@ -XXX,XX +XXX,XX @@ static void armv7m_nvic_reset(DeviceState *dev) s->exception_prio = NVIC_NOEXC_PRIO; s->vectpending = 0; s->vectpending_is_s_banked = false; + s->vectpending_prio = NVIC_NOEXC_PRIO; } static void nvic_systick_trigger(void *opaque, int n, int level) diff --git a/hw/intc/trace-events b/hw/intc/trace-events index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/trace-events +++ b/hw/intc/trace-events @@ -XXX,XX +XXX,XX @@ gicv3_redist_set_irq(uint32_t cpu, int irq, int level) "GICv3 redistributor 0x%x gicv3_redist_send_sgi(uint32_t cpu, int irq) "GICv3 redistributor 0x%x pending SGI %d" # hw/intc/armv7m_nvic.c -nvic_recompute_state(int vectpending, int exception_prio) "NVIC state recomputed: vectpending %d exception_prio %d" +nvic_recompute_state(int vectpending, int vectpending_prio, int exception_prio) "NVIC state recomputed: vectpending %d vectpending_prio %d exception_prio %d" nvic_set_prio(int irq, uint8_t prio) "NVIC set irq %d priority %d" nvic_irq_update(int vectpending, int pendprio, int exception_prio, int level) "NVIC vectpending %d pending prio %d exception_prio %d: setting irq line to %d" nvic_escalate_prio(int irq, int irqprio, int runprio) "NVIC escalating irq %d to HardFault: insufficient priority %d >= %d" -- 2.7.4 The Application Interrupt and Reset Control Register has some changes for v8M: * new bits SYSRESETREQS, BFHFNMINS and PRIS: these all have real state if the security extension is implemented and otherwise are constant * the PRIGROUP field is banked between security states * non-secure code can be blocked from using the SYSRESET bit to reset the system if SYSRESETREQS is set Implement the new state and the changes to register read and write. For the moment we ignore the effects of the secure PRIGROUP. We will implement the effects of PRIS and BFHFNMIS later. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-6-git-send-email-peter.maydell@linaro.org --- include/hw/intc/armv7m_nvic.h | 3 ++- target/arm/cpu.h | 12 +++++++++++ hw/intc/armv7m_nvic.c | 49 +++++++++++++++++++++++++++++++++---------- target/arm/cpu.c | 7 +++++++ 4 files changed, 59 insertions(+), 12 deletions(-) diff --git a/include/hw/intc/armv7m_nvic.h b/include/hw/intc/armv7m_nvic.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/intc/armv7m_nvic.h +++ b/include/hw/intc/armv7m_nvic.h @@ -XXX,XX +XXX,XX @@ typedef struct NVICState { * Entries in sec_vectors[] for non-banked exception numbers are unused. */ VecInfo sec_vectors[NVIC_INTERNAL_VECTORS]; - uint32_t prigroup; + /* The PRIGROUP field in AIRCR is banked */ + uint32_t prigroup[M_REG_NUM_BANKS]; /* The following fields are all cached state that can be recalculated * from the vectors[] and sec_vectors[] arrays and the prigroup field: diff --git a/target/arm/cpu.h b/target/arm/cpu.h index XXXXXXX..XXXXXXX 100644 --- a/target/arm/cpu.h +++ b/target/arm/cpu.h @@ -XXX,XX +XXX,XX @@ typedef struct CPUARMState { int exception; uint32_t primask[M_REG_NUM_BANKS]; uint32_t faultmask[M_REG_NUM_BANKS]; + uint32_t aircr; /* only holds r/w state if security extn implemented */ uint32_t secure; /* Is CPU in Secure state? (not guest visible) */ } v7m; @@ -XXX,XX +XXX,XX @@ FIELD(V7M_CCR, STKALIGN, 9, 1) FIELD(V7M_CCR, DC, 16, 1) FIELD(V7M_CCR, IC, 17, 1) +/* V7M AIRCR bits */ +FIELD(V7M_AIRCR, VECTRESET, 0, 1) +FIELD(V7M_AIRCR, VECTCLRACTIVE, 1, 1) +FIELD(V7M_AIRCR, SYSRESETREQ, 2, 1) +FIELD(V7M_AIRCR, SYSRESETREQS, 3, 1) +FIELD(V7M_AIRCR, PRIGROUP, 8, 3) +FIELD(V7M_AIRCR, BFHFNMINS, 13, 1) +FIELD(V7M_AIRCR, PRIS, 14, 1) +FIELD(V7M_AIRCR, ENDIANNESS, 15, 1) +FIELD(V7M_AIRCR, VECTKEY, 16, 16) + /* V7M CFSR bits for MMFSR */ FIELD(V7M_CFSR, IACCVIOL, 0, 1) FIELD(V7M_CFSR, DACCVIOL, 1, 1) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static bool nvic_isrpending(NVICState *s) */ static inline uint32_t nvic_gprio_mask(NVICState *s) { - return ~0U << (s->prigroup + 1); + return ~0U << (s->prigroup[M_REG_NS] + 1); } /* Recompute vectpending and exception_prio */ @@ -XXX,XX +XXX,XX @@ static uint32_t nvic_readl(NVICState *s, uint32_t offset, MemTxAttrs attrs) return val; case 0xd08: /* Vector Table Offset. */ return cpu->env.v7m.vecbase[attrs.secure]; - case 0xd0c: /* Application Interrupt/Reset Control. */ - return 0xfa050000 | (s->prigroup << 8); + case 0xd0c: /* Application Interrupt/Reset Control (AIRCR) */ + val = 0xfa050000 | (s->prigroup[attrs.secure] << 8); + if (attrs.secure) { + /* s->aircr stores PRIS, BFHFNMINS, SYSRESETREQS */ + val |= cpu->env.v7m.aircr; + } else { + if (arm_feature(&cpu->env, ARM_FEATURE_V8)) { + /* BFHFNMINS is R/O from NS; other bits are RAZ/WI. If + * security isn't supported then BFHFNMINS is RAO (and + * the bit in env.v7m.aircr is always set). + */ + val |= cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK; + } + } + return val; case 0xd10: /* System Control. */ /* TODO: Implement SLEEPONEXIT. */ return 0; @@ -XXX,XX +XXX,XX @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, case 0xd08: /* Vector Table Offset. */ cpu->env.v7m.vecbase[attrs.secure] = value & 0xffffff80; break; - case 0xd0c: /* Application Interrupt/Reset Control. */ - if ((value >> 16) == 0x05fa) { - if (value & 4) { - qemu_irq_pulse(s->sysresetreq); + case 0xd0c: /* Application Interrupt/Reset Control (AIRCR) */ + if ((value >> R_V7M_AIRCR_VECTKEY_SHIFT) == 0x05fa) { + if (value & R_V7M_AIRCR_SYSRESETREQ_MASK) { + if (attrs.secure || + !(cpu->env.v7m.aircr & R_V7M_AIRCR_SYSRESETREQS_MASK)) { + qemu_irq_pulse(s->sysresetreq); + } } - if (value & 2) { + if (value & R_V7M_AIRCR_VECTCLRACTIVE_MASK) { qemu_log_mask(LOG_GUEST_ERROR, "Setting VECTCLRACTIVE when not in DEBUG mode " "is UNPREDICTABLE\n"); } - if (value & 1) { + if (value & R_V7M_AIRCR_VECTRESET_MASK) { + /* NB: this bit is RES0 in v8M */ qemu_log_mask(LOG_GUEST_ERROR, "Setting VECTRESET when not in DEBUG mode " "is UNPREDICTABLE\n"); } - s->prigroup = extract32(value, 8, 3); + s->prigroup[attrs.secure] = extract32(value, + R_V7M_AIRCR_PRIGROUP_SHIFT, + R_V7M_AIRCR_PRIGROUP_LENGTH); + if (attrs.secure) { + /* These bits are only writable by secure */ + cpu->env.v7m.aircr = value & + (R_V7M_AIRCR_SYSRESETREQS_MASK | + R_V7M_AIRCR_BFHFNMINS_MASK | + R_V7M_AIRCR_PRIS_MASK); + } nvic_irq_update(s); } break; @@ -XXX,XX +XXX,XX @@ static const VMStateDescription vmstate_nvic_security = { .fields = (VMStateField[]) { VMSTATE_STRUCT_ARRAY(sec_vectors, NVICState, NVIC_INTERNAL_VECTORS, 1, vmstate_VecInfo, VecInfo), + VMSTATE_UINT32(prigroup[M_REG_S], NVICState), VMSTATE_END_OF_LIST() } }; @@ -XXX,XX +XXX,XX @@ static const VMStateDescription vmstate_nvic = { .fields = (VMStateField[]) { VMSTATE_STRUCT_ARRAY(vectors, NVICState, NVIC_MAX_VECTORS, 1, vmstate_VecInfo, VecInfo), - VMSTATE_UINT32(prigroup, NVICState), + VMSTATE_UINT32(prigroup[M_REG_NS], NVICState), VMSTATE_END_OF_LIST() }, .subsections = (const VMStateDescription*[]) { diff --git a/target/arm/cpu.c b/target/arm/cpu.c index XXXXXXX..XXXXXXX 100644 --- a/target/arm/cpu.c +++ b/target/arm/cpu.c @@ -XXX,XX +XXX,XX @@ static void arm_cpu_reset(CPUState *s) if (arm_feature(env, ARM_FEATURE_M_SECURITY)) { env->v7m.secure = true; + } else { + /* This bit resets to 0 if security is supported, but 1 if + * it is not. The bit is not present in v7M, but we set it + * here so we can avoid having to make checks on it conditional + * on ARM_FEATURE_V8 (we don't let the guest see the bit). + */ + env->v7m.aircr = R_V7M_AIRCR_BFHFNMINS_MASK; } /* In v7M the reset value of this bit is IMPDEF, but ARM recommends -- 2.7.4 Update the code in nvic_rettobase() so that it checks the sec_vectors[] array as well as the vectors[] array if needed. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-7-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static int nvic_pending_prio(NVICState *s) static bool nvic_rettobase(NVICState *s) { int irq, nhand = 0; + bool check_sec = arm_feature(&s->cpu->env, ARM_FEATURE_M_SECURITY); for (irq = ARMV7M_EXCP_RESET; irq < s->num_irq; irq++) { - if (s->vectors[irq].active) { + if (s->vectors[irq].active || + (check_sec && irq < NVIC_INTERNAL_VECTORS && + s->sec_vectors[irq].active)) { nhand++; if (nhand == 2) { return 0; -- 2.7.4 For v8M, the NVIC has a new set of registers per interrupt, NVIC_ITNS<n>. These determine whether the interrupt targets Secure or Non-secure state. Implement the register read/write code for these, and make them cause NVIC_IABR, NVIC_ICER, NVIC_ISER, NVIC_ICPR, NVIC_IPR and NVIC_ISPR to RAZ/WI for non-secure accesses to fields corresponding to interrupts which are configured to target secure state. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-8-git-send-email-peter.maydell@linaro.org --- include/hw/intc/armv7m_nvic.h | 3 ++ hw/intc/armv7m_nvic.c | 74 +++++++++++++++++++++++++++++++++++++++---- 2 files changed, 70 insertions(+), 7 deletions(-) diff --git a/include/hw/intc/armv7m_nvic.h b/include/hw/intc/armv7m_nvic.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/intc/armv7m_nvic.h +++ b/include/hw/intc/armv7m_nvic.h @@ -XXX,XX +XXX,XX @@ typedef struct NVICState { /* The PRIGROUP field in AIRCR is banked */ uint32_t prigroup[M_REG_NUM_BANKS]; + /* v8M NVIC_ITNS state (stored as a bool per bit) */ + bool itns[NVIC_MAX_VECTORS]; + /* The following fields are all cached state that can be recalculated * from the vectors[] and sec_vectors[] arrays and the prigroup field: * - vectpending diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static uint32_t nvic_readl(NVICState *s, uint32_t offset, MemTxAttrs attrs) switch (offset) { case 4: /* Interrupt Control Type. */ return ((s->num_irq - NVIC_FIRST_IRQ) / 32) - 1; + case 0x380 ... 0x3bf: /* NVIC_ITNS<n> */ + { + int startvec = 32 * (offset - 0x380) + NVIC_FIRST_IRQ; + int i; + + if (!arm_feature(&cpu->env, ARM_FEATURE_V8)) { + goto bad_offset; + } + if (!attrs.secure) { + return 0; + } + val = 0; + for (i = 0; i < 32 && startvec + i < s->num_irq; i++) { + if (s->itns[startvec + i]) { + val |= (1 << i); + } + } + return val; + } case 0xd00: /* CPUID Base. */ return cpu->midr; case 0xd04: /* Interrupt Control State. */ @@ -XXX,XX +XXX,XX @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, ARMCPU *cpu = s->cpu; switch (offset) { + case 0x380 ... 0x3bf: /* NVIC_ITNS<n> */ + { + int startvec = 32 * (offset - 0x380) + NVIC_FIRST_IRQ; + int i; + + if (!arm_feature(&cpu->env, ARM_FEATURE_V8)) { + goto bad_offset; + } + if (!attrs.secure) { + break; + } + for (i = 0; i < 32 && startvec + i < s->num_irq; i++) { + s->itns[startvec + i] = (value >> i) & 1; + } + nvic_irq_update(s); + break; + } case 0xd04: /* Interrupt Control State. */ if (value & (1 << 31)) { armv7m_nvic_set_pending(s, ARMV7M_EXCP_NMI); @@ -XXX,XX +XXX,XX @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, startvec = offset - 0x180 + NVIC_FIRST_IRQ; /* vector # */ for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) { - if (s->vectors[startvec + i].enabled) { + if (s->vectors[startvec + i].enabled && + (attrs.secure || s->itns[startvec + i])) { val |= (1 << i); } } @@ -XXX,XX +XXX,XX @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, val = 0; startvec = offset - 0x280 + NVIC_FIRST_IRQ; /* vector # */ for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) { - if (s->vectors[startvec + i].pending) { + if (s->vectors[startvec + i].pending && + (attrs.secure || s->itns[startvec + i])) { val |= (1 << i); } } @@ -XXX,XX +XXX,XX @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, startvec = offset - 0x300 + NVIC_FIRST_IRQ; /* vector # */ for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) { - if (s->vectors[startvec + i].active) { + if (s->vectors[startvec + i].active && + (attrs.secure || s->itns[startvec + i])) { val |= (1 << i); } } @@ -XXX,XX +XXX,XX @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, startvec = offset - 0x400 + NVIC_FIRST_IRQ; /* vector # */ for (i = 0; i < size && startvec + i < s->num_irq; i++) { - val |= s->vectors[startvec + i].prio << (8 * i); + if (attrs.secure || s->itns[startvec + i]) { + val |= s->vectors[startvec + i].prio << (8 * i); + } } break; case 0xd18 ... 0xd23: /* System Handler Priority. */ @@ -XXX,XX +XXX,XX @@ static MemTxResult nvic_sysreg_write(void *opaque, hwaddr addr, startvec = 8 * (offset - 0x180) + NVIC_FIRST_IRQ; for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) { - if (value & (1 << i)) { + if (value & (1 << i) && + (attrs.secure || s->itns[startvec + i])) { s->vectors[startvec + i].enabled = setval; } } @@ -XXX,XX +XXX,XX @@ static MemTxResult nvic_sysreg_write(void *opaque, hwaddr addr, startvec = 8 * (offset - 0x280) + NVIC_FIRST_IRQ; /* vector # */ for (i = 0, end = size * 8; i < end && startvec + i < s->num_irq; i++) { - if (value & (1 << i)) { + if (value & (1 << i) && + (attrs.secure || s->itns[startvec + i])) { s->vectors[startvec + i].pending = setval; } } @@ -XXX,XX +XXX,XX @@ static MemTxResult nvic_sysreg_write(void *opaque, hwaddr addr, startvec = 8 * (offset - 0x400) + NVIC_FIRST_IRQ; /* vector # */ for (i = 0; i < size && startvec + i < s->num_irq; i++) { - set_prio(s, startvec + i, (value >> (i * 8)) & 0xff); + if (attrs.secure || s->itns[startvec + i]) { + set_prio(s, startvec + i, (value >> (i * 8)) & 0xff); + } } nvic_irq_update(s); return MEMTX_OK; @@ -XXX,XX +XXX,XX @@ static const VMStateDescription vmstate_nvic_security = { VMSTATE_STRUCT_ARRAY(sec_vectors, NVICState, NVIC_INTERNAL_VECTORS, 1, vmstate_VecInfo, VecInfo), VMSTATE_UINT32(prigroup[M_REG_S], NVICState), + VMSTATE_BOOL_ARRAY(itns, NVICState, NVIC_MAX_VECTORS), VMSTATE_END_OF_LIST() } }; @@ -XXX,XX +XXX,XX @@ static void armv7m_nvic_reset(DeviceState *dev) s->vectpending = 0; s->vectpending_is_s_banked = false; s->vectpending_prio = NVIC_NOEXC_PRIO; + + if (arm_feature(&s->cpu->env, ARM_FEATURE_M_SECURITY)) { + memset(s->itns, 0, sizeof(s->itns)); + } else { + /* This state is constant and not guest accessible in a non-security + * NVIC; we set the bits to true to avoid having to do a feature + * bit check in the NVIC enable/pend/etc register accessors. + */ + int i; + + for (i = NVIC_FIRST_IRQ; i < ARRAY_SIZE(s->itns); i++) { + s->itns[i] = true; + } + } } static void nvic_systick_trigger(void *opaque, int n, int level) -- 2.7.4 Update the nvic_recompute_state() code to handle the security extension and its associated banked registers. Code that uses the resulting cached state (ie the irq acknowledge and complete code) will be updated in a later commit. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-9-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 151 ++++++++++++++++++++++++++++++++++++++++++++++++-- hw/intc/trace-events | 1 + 2 files changed, 147 insertions(+), 5 deletions(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ * (higher than the highest possible priority value) */ #define NVIC_NOEXC_PRIO 0x100 +/* Maximum priority of non-secure exceptions when AIRCR.PRIS is set */ +#define NVIC_NS_PRIO_LIMIT 0x80 static const uint8_t nvic_id[] = { 0x00, 0xb0, 0x1b, 0x00, 0x0d, 0xe0, 0x05, 0xb1 @@ -XXX,XX +XXX,XX @@ static bool nvic_isrpending(NVICState *s) return false; } +static bool exc_is_banked(int exc) +{ + /* Return true if this is one of the limited set of exceptions which + * are banked (and thus have state in sec_vectors[]) + */ + return exc == ARMV7M_EXCP_HARD || + exc == ARMV7M_EXCP_MEM || + exc == ARMV7M_EXCP_USAGE || + exc == ARMV7M_EXCP_SVC || + exc == ARMV7M_EXCP_PENDSV || + exc == ARMV7M_EXCP_SYSTICK; +} + /* Return a mask word which clears the subpriority bits from * a priority value for an M-profile exception, leaving only * the group priority. */ -static inline uint32_t nvic_gprio_mask(NVICState *s) +static inline uint32_t nvic_gprio_mask(NVICState *s, bool secure) +{ + return ~0U << (s->prigroup[secure] + 1); +} + +static bool exc_targets_secure(NVICState *s, int exc) +{ + /* Return true if this non-banked exception targets Secure state. */ + if (!arm_feature(&s->cpu->env, ARM_FEATURE_M_SECURITY)) { + return false; + } + + if (exc >= NVIC_FIRST_IRQ) { + return !s->itns[exc]; + } + + /* Function shouldn't be called for banked exceptions. */ + assert(!exc_is_banked(exc)); + + switch (exc) { + case ARMV7M_EXCP_NMI: + case ARMV7M_EXCP_BUS: + return !(s->cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK); + case ARMV7M_EXCP_SECURE: + return true; + case ARMV7M_EXCP_DEBUG: + /* TODO: controlled by DEMCR.SDME, which we don't yet implement */ + return false; + default: + /* reset, and reserved (unused) low exception numbers. + * We'll get called by code that loops through all the exception + * numbers, but it doesn't matter what we return here as these + * non-existent exceptions will never be pended or active. + */ + return true; + } +} + +static int exc_group_prio(NVICState *s, int rawprio, bool targets_secure) +{ + /* Return the group priority for this exception, given its raw + * (group-and-subgroup) priority value and whether it is targeting + * secure state or not. + */ + if (rawprio < 0) { + return rawprio; + } + rawprio &= nvic_gprio_mask(s, targets_secure); + /* AIRCR.PRIS causes us to squash all NS priorities into the + * lower half of the total range + */ + if (!targets_secure && + (s->cpu->env.v7m.aircr & R_V7M_AIRCR_PRIS_MASK)) { + rawprio = (rawprio >> 1) + NVIC_NS_PRIO_LIMIT; + } + return rawprio; +} + +/* Recompute vectpending and exception_prio for a CPU which implements + * the Security extension + */ +static void nvic_recompute_state_secure(NVICState *s) { - return ~0U << (s->prigroup[M_REG_NS] + 1); + int i, bank; + int pend_prio = NVIC_NOEXC_PRIO; + int active_prio = NVIC_NOEXC_PRIO; + int pend_irq = 0; + bool pending_is_s_banked = false; + + /* R_CQRV: precedence is by: + * - lowest group priority; if both the same then + * - lowest subpriority; if both the same then + * - lowest exception number; if both the same (ie banked) then + * - secure exception takes precedence + * Compare pseudocode RawExecutionPriority. + * Annoyingly, now we have two prigroup values (for S and NS) + * we can't do the loop comparison on raw priority values. + */ + for (i = 1; i < s->num_irq; i++) { + for (bank = M_REG_S; bank >= M_REG_NS; bank--) { + VecInfo *vec; + int prio; + bool targets_secure; + + if (bank == M_REG_S) { + if (!exc_is_banked(i)) { + continue; + } + vec = &s->sec_vectors[i]; + targets_secure = true; + } else { + vec = &s->vectors[i]; + targets_secure = !exc_is_banked(i) && exc_targets_secure(s, i); + } + + prio = exc_group_prio(s, vec->prio, targets_secure); + if (vec->enabled && vec->pending && prio < pend_prio) { + pend_prio = prio; + pend_irq = i; + pending_is_s_banked = (bank == M_REG_S); + } + if (vec->active && prio < active_prio) { + active_prio = prio; + } + } + } + + s->vectpending_is_s_banked = pending_is_s_banked; + s->vectpending = pend_irq; + s->vectpending_prio = pend_prio; + s->exception_prio = active_prio; + + trace_nvic_recompute_state_secure(s->vectpending, + s->vectpending_is_s_banked, + s->vectpending_prio, + s->exception_prio); } /* Recompute vectpending and exception_prio */ @@ -XXX,XX +XXX,XX @@ static void nvic_recompute_state(NVICState *s) int active_prio = NVIC_NOEXC_PRIO; int pend_irq = 0; + /* In theory we could write one function that handled both + * the "security extension present" and "not present"; however + * the security related changes significantly complicate the + * recomputation just by themselves and mixing both cases together + * would be even worse, so we retain a separate non-secure-only + * version for CPUs which don't implement the security extension. + */ + if (arm_feature(&s->cpu->env, ARM_FEATURE_M_SECURITY)) { + nvic_recompute_state_secure(s); + return; + } + for (i = 1; i < s->num_irq; i++) { VecInfo *vec = &s->vectors[i]; @@ -XXX,XX +XXX,XX @@ static void nvic_recompute_state(NVICState *s) } if (active_prio > 0) { - active_prio &= nvic_gprio_mask(s); + active_prio &= nvic_gprio_mask(s, false); } if (pend_prio > 0) { - pend_prio &= nvic_gprio_mask(s); + pend_prio &= nvic_gprio_mask(s, false); } s->vectpending = pend_irq; @@ -XXX,XX +XXX,XX @@ static inline int nvic_exec_prio(NVICState *s) } else if (env->v7m.primask[env->v7m.secure]) { running = 0; } else if (env->v7m.basepri[env->v7m.secure] > 0) { - running = env->v7m.basepri[env->v7m.secure] & nvic_gprio_mask(s); + running = env->v7m.basepri[env->v7m.secure] & + nvic_gprio_mask(s, env->v7m.secure); } else { running = NVIC_NOEXC_PRIO; /* lower than any possible priority */ } diff --git a/hw/intc/trace-events b/hw/intc/trace-events index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/trace-events +++ b/hw/intc/trace-events @@ -XXX,XX +XXX,XX @@ gicv3_redist_send_sgi(uint32_t cpu, int irq) "GICv3 redistributor 0x%x pending S # hw/intc/armv7m_nvic.c nvic_recompute_state(int vectpending, int vectpending_prio, int exception_prio) "NVIC state recomputed: vectpending %d vectpending_prio %d exception_prio %d" +nvic_recompute_state_secure(int vectpending, bool vectpending_is_s_banked, int vectpending_prio, int exception_prio) "NVIC state recomputed: vectpending %d is_s_banked %d vectpending_prio %d exception_prio %d" nvic_set_prio(int irq, uint8_t prio) "NVIC set irq %d priority %d" nvic_irq_update(int vectpending, int pendprio, int exception_prio, int level) "NVIC vectpending %d pending prio %d exception_prio %d: setting irq line to %d" nvic_escalate_prio(int irq, int irqprio, int runprio) "NVIC escalating irq %d to HardFault: insufficient priority %d >= %d" -- 2.7.4 Make the armv7m_nvic_set_pending() and armv7m_nvic_clear_pending() functions take a bool indicating whether to pend the secure or non-secure version of a banked interrupt, and update the callsites accordingly. In most callsites we can simply pass the correct security state in; in a couple of cases we use TODO comments to indicate that we will return the code in a subsequent commit. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-10-git-send-email-peter.maydell@linaro.org --- target/arm/cpu.h | 14 ++++++++++- hw/intc/armv7m_nvic.c | 64 ++++++++++++++++++++++++++++++++++++++------------- target/arm/helper.c | 24 +++++++++++-------- hw/intc/trace-events | 4 ++-- 4 files changed, 77 insertions(+), 29 deletions(-) diff --git a/target/arm/cpu.h b/target/arm/cpu.h index XXXXXXX..XXXXXXX 100644 --- a/target/arm/cpu.h +++ b/target/arm/cpu.h @@ -XXX,XX +XXX,XX @@ static inline bool armv7m_nvic_can_take_pending_exception(void *opaque) return true; } #endif -void armv7m_nvic_set_pending(void *opaque, int irq); +/** + * armv7m_nvic_set_pending: mark the specified exception as pending + * @opaque: the NVIC + * @irq: the exception number to mark pending + * @secure: false for non-banked exceptions or for the nonsecure + * version of a banked exception, true for the secure version of a banked + * exception. + * + * Marks the specified exception as pending. Note that we will assert() + * if @secure is true and @irq does not specify one of the fixed set + * of architecturally banked exceptions. + */ +void armv7m_nvic_set_pending(void *opaque, int irq, bool secure); void armv7m_nvic_acknowledge_irq(void *opaque); /** * armv7m_nvic_complete_irq: complete specified interrupt or exception diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static void nvic_irq_update(NVICState *s) qemu_set_irq(s->excpout, lvl); } -static void armv7m_nvic_clear_pending(void *opaque, int irq) +/** + * armv7m_nvic_clear_pending: mark the specified exception as not pending + * @opaque: the NVIC + * @irq: the exception number to mark as not pending + * @secure: false for non-banked exceptions or for the nonsecure + * version of a banked exception, true for the secure version of a banked + * exception. + * + * Marks the specified exception as not pending. Note that we will assert() + * if @secure is true and @irq does not specify one of the fixed set + * of architecturally banked exceptions. + */ +static void armv7m_nvic_clear_pending(void *opaque, int irq, bool secure) { NVICState *s = (NVICState *)opaque; VecInfo *vec; assert(irq > ARMV7M_EXCP_RESET && irq < s->num_irq); - vec = &s->vectors[irq]; - trace_nvic_clear_pending(irq, vec->enabled, vec->prio); + if (secure) { + assert(exc_is_banked(irq)); + vec = &s->sec_vectors[irq]; + } else { + vec = &s->vectors[irq]; + } + trace_nvic_clear_pending(irq, secure, vec->enabled, vec->prio); if (vec->pending) { vec->pending = 0; nvic_irq_update(s); } } -void armv7m_nvic_set_pending(void *opaque, int irq) +void armv7m_nvic_set_pending(void *opaque, int irq, bool secure) { NVICState *s = (NVICState *)opaque; + bool banked = exc_is_banked(irq); VecInfo *vec; assert(irq > ARMV7M_EXCP_RESET && irq < s->num_irq); + assert(!secure || banked); - vec = &s->vectors[irq]; - trace_nvic_set_pending(irq, vec->enabled, vec->prio); + vec = (banked && secure) ? &s->sec_vectors[irq] : &s->vectors[irq]; + trace_nvic_set_pending(irq, secure, vec->enabled, vec->prio); if (irq >= ARMV7M_EXCP_HARD && irq < ARMV7M_EXCP_PENDSV) { /* If a synchronous exception is pending then it may be @@ -XXX,XX +XXX,XX @@ void armv7m_nvic_set_pending(void *opaque, int irq) "(current priority %d)\n", irq, running); } - /* We can do the escalation, so we take HardFault instead */ + /* We can do the escalation, so we take HardFault instead. + * If BFHFNMINS is set then we escalate to the banked HF for + * the target security state of the original exception; otherwise + * we take a Secure HardFault. + */ irq = ARMV7M_EXCP_HARD; - vec = &s->vectors[irq]; + if (arm_feature(&s->cpu->env, ARM_FEATURE_M_SECURITY) && + (secure || + !(s->cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK))) { + vec = &s->sec_vectors[irq]; + } else { + vec = &s->vectors[irq]; + } + /* HF may be banked but there is only one shared HFSR */ s->cpu->env.v7m.hfsr |= R_V7M_HFSR_FORCED_MASK; } } @@ -XXX,XX +XXX,XX @@ static void set_irq_level(void *opaque, int n, int level) if (level != vec->level) { vec->level = level; if (level) { - armv7m_nvic_set_pending(s, n); + armv7m_nvic_set_pending(s, n, false); } } } @@ -XXX,XX +XXX,XX @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, } case 0xd04: /* Interrupt Control State. */ if (value & (1 << 31)) { - armv7m_nvic_set_pending(s, ARMV7M_EXCP_NMI); + armv7m_nvic_set_pending(s, ARMV7M_EXCP_NMI, false); } if (value & (1 << 28)) { - armv7m_nvic_set_pending(s, ARMV7M_EXCP_PENDSV); + armv7m_nvic_set_pending(s, ARMV7M_EXCP_PENDSV, attrs.secure); } else if (value & (1 << 27)) { - armv7m_nvic_clear_pending(s, ARMV7M_EXCP_PENDSV); + armv7m_nvic_clear_pending(s, ARMV7M_EXCP_PENDSV, attrs.secure); } if (value & (1 << 26)) { - armv7m_nvic_set_pending(s, ARMV7M_EXCP_SYSTICK); + armv7m_nvic_set_pending(s, ARMV7M_EXCP_SYSTICK, attrs.secure); } else if (value & (1 << 25)) { - armv7m_nvic_clear_pending(s, ARMV7M_EXCP_SYSTICK); + armv7m_nvic_clear_pending(s, ARMV7M_EXCP_SYSTICK, attrs.secure); } break; case 0xd08: /* Vector Table Offset. */ @@ -XXX,XX +XXX,XX @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, { int excnum = (value & 0x1ff) + NVIC_FIRST_IRQ; if (excnum < s->num_irq) { - armv7m_nvic_set_pending(s, excnum); + armv7m_nvic_set_pending(s, excnum, false); } break; } @@ -XXX,XX +XXX,XX @@ static void nvic_systick_trigger(void *opaque, int n, int level) /* SysTick just asked us to pend its exception. * (This is different from an external interrupt line's * behaviour.) + * TODO: when we implement the banked systicks we must make + * this pend the correct banked exception. */ - armv7m_nvic_set_pending(s, ARMV7M_EXCP_SYSTICK); + armv7m_nvic_set_pending(s, ARMV7M_EXCP_SYSTICK, false); } } diff --git a/target/arm/helper.c b/target/arm/helper.c index XXXXXXX..XXXXXXX 100644 --- a/target/arm/helper.c +++ b/target/arm/helper.c @@ -XXX,XX +XXX,XX @@ static void do_v7m_exception_exit(ARMCPU *cpu) * stack, directly take a usage fault on the current stack. */ env->v7m.cfsr[env->v7m.secure] |= R_V7M_CFSR_INVPC_MASK; - armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE); + armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE, env->v7m.secure); v7m_exception_taken(cpu, excret); qemu_log_mask(CPU_LOG_INT, "...taking UsageFault on existing " "stackframe: failed exception return integrity check\n"); @@ -XXX,XX +XXX,XX @@ static void do_v7m_exception_exit(ARMCPU *cpu) * exception return excret specified then this is a UsageFault. */ if (return_to_handler != arm_v7m_is_handler_mode(env)) { - /* Take an INVPC UsageFault by pushing the stack again. */ - armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE); + /* Take an INVPC UsageFault by pushing the stack again. + * TODO: the v8M version of this code should target the + * background state for this exception. + */ + armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE, false); env->v7m.cfsr[env->v7m.secure] |= R_V7M_CFSR_INVPC_MASK; v7m_push_stack(cpu); v7m_exception_taken(cpu, excret); @@ -XXX,XX +XXX,XX @@ void arm_v7m_cpu_do_interrupt(CPUState *cs) handle it. */ switch (cs->exception_index) { case EXCP_UDEF: - armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE); + armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE, env->v7m.secure); env->v7m.cfsr[env->v7m.secure] |= R_V7M_CFSR_UNDEFINSTR_MASK; break; case EXCP_NOCP: - armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE); + armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE, env->v7m.secure); env->v7m.cfsr[env->v7m.secure] |= R_V7M_CFSR_NOCP_MASK; break; case EXCP_INVSTATE: - armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE); + armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_USAGE, env->v7m.secure); env->v7m.cfsr[env->v7m.secure] |= R_V7M_CFSR_INVSTATE_MASK; break; case EXCP_SWI: /* The PC already points to the next instruction. */ - armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_SVC); + armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_SVC, env->v7m.secure); break; case EXCP_PREFETCH_ABORT: case EXCP_DATA_ABORT: @@ -XXX,XX +XXX,XX @@ void arm_v7m_cpu_do_interrupt(CPUState *cs) env->v7m.bfar); break; } - armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_BUS); + armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_BUS, false); break; default: /* All other FSR values are either MPU faults or "can't happen @@ -XXX,XX +XXX,XX @@ void arm_v7m_cpu_do_interrupt(CPUState *cs) env->v7m.mmfar[env->v7m.secure]); break; } - armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_MEM); + armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_MEM, + env->v7m.secure); break; } break; @@ -XXX,XX +XXX,XX @@ void arm_v7m_cpu_do_interrupt(CPUState *cs) return; } } - armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_DEBUG); + armv7m_nvic_set_pending(env->nvic, ARMV7M_EXCP_DEBUG, false); break; case EXCP_IRQ: break; diff --git a/hw/intc/trace-events b/hw/intc/trace-events index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/trace-events +++ b/hw/intc/trace-events @@ -XXX,XX +XXX,XX @@ nvic_set_prio(int irq, uint8_t prio) "NVIC set irq %d priority %d" nvic_irq_update(int vectpending, int pendprio, int exception_prio, int level) "NVIC vectpending %d pending prio %d exception_prio %d: setting irq line to %d" nvic_escalate_prio(int irq, int irqprio, int runprio) "NVIC escalating irq %d to HardFault: insufficient priority %d >= %d" nvic_escalate_disabled(int irq) "NVIC escalating irq %d to HardFault: disabled" -nvic_set_pending(int irq, int en, int prio) "NVIC set pending irq %d (enabled: %d priority %d)" -nvic_clear_pending(int irq, int en, int prio) "NVIC clear pending irq %d (enabled: %d priority %d)" +nvic_set_pending(int irq, bool secure, int en, int prio) "NVIC set pending irq %d secure-bank %d (enabled: %d priority %d)" +nvic_clear_pending(int irq, bool secure, int en, int prio) "NVIC clear pending irq %d secure-bank %d (enabled: %d priority %d)" nvic_set_pending_level(int irq) "NVIC set pending: irq %d higher prio than vectpending: setting irq line to 1" nvic_acknowledge_irq(int irq, int prio) "NVIC acknowledge IRQ: %d now active (prio %d)" nvic_complete_irq(int irq) "NVIC complete IRQ %d" -- 2.7.4 Make the set_prio() function take a bool indicating whether to pend the secure or non-secure version of a banked interrupt, and use this to implement the correct banking semantics for the SHPR registers. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-11-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 96 ++++++++++++++++++++++++++++++++++++++++++++++----- hw/intc/trace-events | 2 +- 2 files changed, 88 insertions(+), 10 deletions(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ int armv7m_nvic_raw_execution_priority(void *opaque) return s->exception_prio; } -/* caller must call nvic_irq_update() after this */ -static void set_prio(NVICState *s, unsigned irq, uint8_t prio) +/* caller must call nvic_irq_update() after this. + * secure indicates the bank to use for banked exceptions (we assert if + * we are passed secure=true for a non-banked exception). + */ +static void set_prio(NVICState *s, unsigned irq, bool secure, uint8_t prio) { assert(irq > ARMV7M_EXCP_NMI); /* only use for configurable prios */ assert(irq < s->num_irq); - s->vectors[irq].prio = prio; + if (secure) { + assert(exc_is_banked(irq)); + s->sec_vectors[irq].prio = prio; + } else { + s->vectors[irq].prio = prio; + } + + trace_nvic_set_prio(irq, secure, prio); +} + +/* Return the current raw priority register value. + * secure indicates the bank to use for banked exceptions (we assert if + * we are passed secure=true for a non-banked exception). + */ +static int get_prio(NVICState *s, unsigned irq, bool secure) +{ + assert(irq > ARMV7M_EXCP_NMI); /* only use for configurable prios */ + assert(irq < s->num_irq); - trace_nvic_set_prio(irq, prio); + if (secure) { + assert(exc_is_banked(irq)); + return s->sec_vectors[irq].prio; + } else { + return s->vectors[irq].prio; + } } /* Recompute state and assert irq line accordingly. @@ -XXX,XX +XXX,XX @@ static bool nvic_user_access_ok(NVICState *s, hwaddr offset, MemTxAttrs attrs) } } +static int shpr_bank(NVICState *s, int exc, MemTxAttrs attrs) +{ + /* Behaviour for the SHPR register field for this exception: + * return M_REG_NS to use the nonsecure vector (including for + * non-banked exceptions), M_REG_S for the secure version of + * a banked exception, and -1 if this field should RAZ/WI. + */ + switch (exc) { + case ARMV7M_EXCP_MEM: + case ARMV7M_EXCP_USAGE: + case ARMV7M_EXCP_SVC: + case ARMV7M_EXCP_PENDSV: + case ARMV7M_EXCP_SYSTICK: + /* Banked exceptions */ + return attrs.secure; + case ARMV7M_EXCP_BUS: + /* Not banked, RAZ/WI from nonsecure if BFHFNMINS is zero */ + if (!attrs.secure && + !(s->cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK)) { + return -1; + } + return M_REG_NS; + case ARMV7M_EXCP_SECURE: + /* Not banked, RAZ/WI from nonsecure */ + if (!attrs.secure) { + return -1; + } + return M_REG_NS; + case ARMV7M_EXCP_DEBUG: + /* Not banked. TODO should RAZ/WI if DEMCR.SDME is set */ + return M_REG_NS; + case 8 ... 10: + case 13: + /* RES0 */ + return -1; + default: + /* Not reachable due to decode of SHPR register addresses */ + g_assert_not_reached(); + } +} + static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, uint64_t *data, unsigned size, MemTxAttrs attrs) @@ -XXX,XX +XXX,XX @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, } } break; - case 0xd18 ... 0xd23: /* System Handler Priority. */ + case 0xd18 ... 0xd23: /* System Handler Priority (SHPR1, SHPR2, SHPR3) */ val = 0; for (i = 0; i < size; i++) { - val |= s->vectors[(offset - 0xd14) + i].prio << (i * 8); + unsigned hdlidx = (offset - 0xd14) + i; + int sbank = shpr_bank(s, hdlidx, attrs); + + if (sbank < 0) { + continue; + } + val = deposit32(val, i * 8, 8, get_prio(s, hdlidx, sbank)); } break; case 0xfe0 ... 0xfff: /* ID. */ @@ -XXX,XX +XXX,XX @@ static MemTxResult nvic_sysreg_write(void *opaque, hwaddr addr, for (i = 0; i < size && startvec + i < s->num_irq; i++) { if (attrs.secure || s->itns[startvec + i]) { - set_prio(s, startvec + i, (value >> (i * 8)) & 0xff); + set_prio(s, startvec + i, false, (value >> (i * 8)) & 0xff); } } nvic_irq_update(s); return MEMTX_OK; - case 0xd18 ... 0xd23: /* System Handler Priority. */ + case 0xd18 ... 0xd23: /* System Handler Priority (SHPR1, SHPR2, SHPR3) */ for (i = 0; i < size; i++) { unsigned hdlidx = (offset - 0xd14) + i; - set_prio(s, hdlidx, (value >> (i * 8)) & 0xff); + int newprio = extract32(value, i * 8, 8); + int sbank = shpr_bank(s, hdlidx, attrs); + + if (sbank < 0) { + continue; + } + set_prio(s, hdlidx, sbank, newprio); } nvic_irq_update(s); return MEMTX_OK; diff --git a/hw/intc/trace-events b/hw/intc/trace-events index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/trace-events +++ b/hw/intc/trace-events @@ -XXX,XX +XXX,XX @@ gicv3_redist_send_sgi(uint32_t cpu, int irq) "GICv3 redistributor 0x%x pending S # hw/intc/armv7m_nvic.c nvic_recompute_state(int vectpending, int vectpending_prio, int exception_prio) "NVIC state recomputed: vectpending %d vectpending_prio %d exception_prio %d" nvic_recompute_state_secure(int vectpending, bool vectpending_is_s_banked, int vectpending_prio, int exception_prio) "NVIC state recomputed: vectpending %d is_s_banked %d vectpending_prio %d exception_prio %d" -nvic_set_prio(int irq, uint8_t prio) "NVIC set irq %d priority %d" +nvic_set_prio(int irq, bool secure, uint8_t prio) "NVIC set irq %d secure-bank %d priority %d" nvic_irq_update(int vectpending, int pendprio, int exception_prio, int level) "NVIC vectpending %d pending prio %d exception_prio %d: setting irq line to %d" nvic_escalate_prio(int irq, int irqprio, int runprio) "NVIC escalating irq %d to HardFault: insufficient priority %d >= %d" nvic_escalate_disabled(int irq) "NVIC escalating irq %d to HardFault: disabled" -- 2.7.4 In armv7m_nvic_set_pending() we have to compare the priority of an exception against the execution priority to decide whether it needs to be escalated to HardFault. In the specification this is a comparison against the exception's group priority; for v7M we implemented it as a comparison against the raw exception priority because the two comparisons will always give the same answer. For v8M the existence of AIRCR.PRIS and the possibility of different PRIGROUP values for secure and nonsecure exceptions means we need to explicitly calculate the vector's group priority for this check. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-12-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ void armv7m_nvic_set_pending(void *opaque, int irq, bool secure) int running = nvic_exec_prio(s); bool escalate = false; - if (vec->prio >= running) { + if (exc_group_prio(s, vec->prio, secure) >= running) { trace_nvic_escalate_prio(irq, vec->prio, running); escalate = true; } else if (!vec->enabled) { -- 2.7.4 When escalating to HardFault, we must go into Lockup if we can't take the synchronous HardFault because the current execution priority is already at or below the priority of HardFault. In v7M HF is always priority -1 so a simple < 0 comparison sufficed; in v8M the priority of HardFault can vary depending on whether it is a Secure or NonSecure HardFault, so we must check against the priority of the HardFault exception vector we're about to use. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-13-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 23 ++++++++++++----------- 1 file changed, 12 insertions(+), 11 deletions(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ void armv7m_nvic_set_pending(void *opaque, int irq, bool secure) } if (escalate) { - if (running < 0) { - /* We want to escalate to HardFault but we can't take a - * synchronous HardFault at this point either. This is a - * Lockup condition due to a guest bug. We don't model - * Lockup, so report via cpu_abort() instead. - */ - cpu_abort(&s->cpu->parent_obj, - "Lockup: can't escalate %d to HardFault " - "(current priority %d)\n", irq, running); - } - /* We can do the escalation, so we take HardFault instead. + /* We need to escalate this exception to a synchronous HardFault. * If BFHFNMINS is set then we escalate to the banked HF for * the target security state of the original exception; otherwise * we take a Secure HardFault. @@ -XXX,XX +XXX,XX @@ void armv7m_nvic_set_pending(void *opaque, int irq, bool secure) } else { vec = &s->vectors[irq]; } + if (running <= vec->prio) { + /* We want to escalate to HardFault but we can't take the + * synchronous HardFault at this point either. This is a + * Lockup condition due to a guest bug. We don't model + * Lockup, so report via cpu_abort() instead. + */ + cpu_abort(&s->cpu->parent_obj, + "Lockup: can't escalate %d to HardFault " + "(current priority %d)\n", irq, running); + } + /* HF may be banked but there is only one shared HFSR */ s->cpu->env.v7m.hfsr |= R_V7M_HFSR_FORCED_MASK; } -- 2.7.4 In v7M, the fixed-priority exceptions are: Reset: -3 NMI: -2 HardFault: -1 In v8M, this changes because Secure HardFault may need to be prioritised above NMI: Reset: -4 Secure HardFault if AIRCR.BFHFNMINS == 1: -3 NMI: -2 Secure HardFault if AIRCR.BFHFNMINS == 0: -1 NonSecure HardFault: -1 Make these changes, including support for changing the priority of Secure HardFault as AIRCR.BFHFNMINS changes. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-14-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 22 +++++++++++++++++++--- 1 file changed, 19 insertions(+), 3 deletions(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, (R_V7M_AIRCR_SYSRESETREQS_MASK | R_V7M_AIRCR_BFHFNMINS_MASK | R_V7M_AIRCR_PRIS_MASK); + /* BFHFNMINS changes the priority of Secure HardFault */ + if (cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK) { + s->sec_vectors[ARMV7M_EXCP_HARD].prio = -3; + } else { + s->sec_vectors[ARMV7M_EXCP_HARD].prio = -1; + } } nvic_irq_update(s); } @@ -XXX,XX +XXX,XX @@ static int nvic_post_load(void *opaque, int version_id) { NVICState *s = opaque; unsigned i; + int resetprio; /* Check for out of range priority settings */ - if (s->vectors[ARMV7M_EXCP_RESET].prio != -3 || + resetprio = arm_feature(&s->cpu->env, ARM_FEATURE_V8) ? -4 : -3; + + if (s->vectors[ARMV7M_EXCP_RESET].prio != resetprio || s->vectors[ARMV7M_EXCP_NMI].prio != -2 || s->vectors[ARMV7M_EXCP_HARD].prio != -1) { return 1; @@ -XXX,XX +XXX,XX @@ static int nvic_security_post_load(void *opaque, int version_id) int i; /* Check for out of range priority settings */ - if (s->sec_vectors[ARMV7M_EXCP_HARD].prio != -1) { + if (s->sec_vectors[ARMV7M_EXCP_HARD].prio != -1 + && s->sec_vectors[ARMV7M_EXCP_HARD].prio != -3) { + /* We can't cross-check against AIRCR.BFHFNMINS as we don't know + * if the CPU state has been migrated yet; a mismatch won't + * cause the emulation to blow up, though. + */ return 1; } for (i = ARMV7M_EXCP_MEM; i < ARRAY_SIZE(s->sec_vectors); i++) { @@ -XXX,XX +XXX,XX @@ static Property props_nvic[] = { static void armv7m_nvic_reset(DeviceState *dev) { + int resetprio; NVICState *s = NVIC(dev); s->vectors[ARMV7M_EXCP_NMI].enabled = 1; @@ -XXX,XX +XXX,XX @@ static void armv7m_nvic_reset(DeviceState *dev) s->vectors[ARMV7M_EXCP_PENDSV].enabled = 1; s->vectors[ARMV7M_EXCP_SYSTICK].enabled = 1; - s->vectors[ARMV7M_EXCP_RESET].prio = -3; + resetprio = arm_feature(&s->cpu->env, ARM_FEATURE_V8) ? -4 : -3; + s->vectors[ARMV7M_EXCP_RESET].prio = resetprio; s->vectors[ARMV7M_EXCP_NMI].prio = -2; s->vectors[ARMV7M_EXCP_HARD].prio = -1; -- 2.7.4 If AIRCR.BFHFNMINS is clear, then although NonSecure HardFault can still be pended via SHCSR.HARDFAULTPENDED it mustn't actually preempt execution. The simple way to achieve this is to clear the enable bit for it, since the enable bit isn't guest visible. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-15-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 12 ++++++++++-- 1 file changed, 10 insertions(+), 2 deletions(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, (R_V7M_AIRCR_SYSRESETREQS_MASK | R_V7M_AIRCR_BFHFNMINS_MASK | R_V7M_AIRCR_PRIS_MASK); - /* BFHFNMINS changes the priority of Secure HardFault */ + /* BFHFNMINS changes the priority of Secure HardFault, and + * allows a pending Non-secure HardFault to preempt (which + * we implement by marking it enabled). + */ if (cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK) { s->sec_vectors[ARMV7M_EXCP_HARD].prio = -3; + s->vectors[ARMV7M_EXCP_HARD].enabled = 1; } else { s->sec_vectors[ARMV7M_EXCP_HARD].prio = -1; + s->vectors[ARMV7M_EXCP_HARD].enabled = 0; } } nvic_irq_update(s); @@ -XXX,XX +XXX,XX @@ static void armv7m_nvic_reset(DeviceState *dev) NVICState *s = NVIC(dev); s->vectors[ARMV7M_EXCP_NMI].enabled = 1; - s->vectors[ARMV7M_EXCP_HARD].enabled = 1; /* MEM, BUS, and USAGE are enabled through * the System Handler Control register */ @@ -XXX,XX +XXX,XX @@ static void armv7m_nvic_reset(DeviceState *dev) /* AIRCR.BFHFNMINS resets to 0 so Secure HF is priority -1 (R_CMTC) */ s->sec_vectors[ARMV7M_EXCP_HARD].prio = -1; + /* If AIRCR.BFHFNMINS is 0 then NS HF is (effectively) disabled */ + s->vectors[ARMV7M_EXCP_HARD].enabled = 0; + } else { + s->vectors[ARMV7M_EXCP_HARD].enabled = 1; } /* Strictly speaking the reset handler should be enabled. -- 2.7.4 Update nvic_exec_prio() to support the v8M changes: * BASEPRI, FAULTMASK and PRIMASK are all banked * AIRCR.PRIS can affect NS priorities * AIRCR.BFHFNMINS affects FAULTMASK behaviour These changes mean that it's no longer possible to definitely say that if FAULTMASK is set it overrides PRIMASK, and if PRIMASK is set it overrides BASEPRI (since if PRIMASK_NS is set and AIRCR.PRIS is set then whether that 0x80 priority should take effect or the priority in BASEPRI_S depends on the value of BASEPRI_S, for instance). So we switch to the same approach used by the pseudocode of working through BASEPRI, PRIMASK and FAULTMASK and overriding the previous values if needed. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-16-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 51 ++++++++++++++++++++++++++++++++++++++++++--------- 1 file changed, 42 insertions(+), 9 deletions(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static void nvic_recompute_state(NVICState *s) static inline int nvic_exec_prio(NVICState *s) { CPUARMState *env = &s->cpu->env; - int running; + int running = NVIC_NOEXC_PRIO; - if (env->v7m.faultmask[env->v7m.secure]) { - running = -1; - } else if (env->v7m.primask[env->v7m.secure]) { + if (env->v7m.basepri[M_REG_NS] > 0) { + running = exc_group_prio(s, env->v7m.basepri[M_REG_NS], M_REG_NS); + } + + if (env->v7m.basepri[M_REG_S] > 0) { + int basepri = exc_group_prio(s, env->v7m.basepri[M_REG_S], M_REG_S); + if (running > basepri) { + running = basepri; + } + } + + if (env->v7m.primask[M_REG_NS]) { + if (env->v7m.aircr & R_V7M_AIRCR_PRIS_MASK) { + if (running > NVIC_NS_PRIO_LIMIT) { + running = NVIC_NS_PRIO_LIMIT; + } + } else { + running = 0; + } + } + + if (env->v7m.primask[M_REG_S]) { running = 0; - } else if (env->v7m.basepri[env->v7m.secure] > 0) { - running = env->v7m.basepri[env->v7m.secure] & - nvic_gprio_mask(s, env->v7m.secure); - } else { - running = NVIC_NOEXC_PRIO; /* lower than any possible priority */ } + + if (env->v7m.faultmask[M_REG_NS]) { + if (env->v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK) { + running = -1; + } else { + if (env->v7m.aircr & R_V7M_AIRCR_PRIS_MASK) { + if (running > NVIC_NS_PRIO_LIMIT) { + running = NVIC_NS_PRIO_LIMIT; + } + } else { + running = 0; + } + } + } + + if (env->v7m.faultmask[M_REG_S]) { + running = (env->v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK) ? -3 : -1; + } + /* consider priority of active handler */ return MIN(running, s->exception_prio); } -- 2.7.4 Now that we have a banked FAULTMASK register and banked exceptions, we can implement the correct check in cpu_mmu_index() for whether the MPU_CTRL.HFNMIENA bit's effect should apply. This bit causes handlers which have requested a negative execution priority to run with the MPU disabled. In v8M the test has to check this for the current security state and so takes account of banking. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-17-git-send-email-peter.maydell@linaro.org --- target/arm/cpu.h | 21 ++++++++++++++++----- hw/intc/armv7m_nvic.c | 29 +++++++++++++++++++++++++++++ 2 files changed, 45 insertions(+), 5 deletions(-) diff --git a/target/arm/cpu.h b/target/arm/cpu.h index XXXXXXX..XXXXXXX 100644 --- a/target/arm/cpu.h +++ b/target/arm/cpu.h @@ -XXX,XX +XXX,XX @@ int armv7m_nvic_complete_irq(void *opaque, int irq); * (v8M ARM ARM I_PKLD.) */ int armv7m_nvic_raw_execution_priority(void *opaque); +/** + * armv7m_nvic_neg_prio_requested: return true if the requested execution + * priority is negative for the specified security state. + * @opaque: the NVIC + * @secure: the security state to test + * This corresponds to the pseudocode IsReqExecPriNeg(). + */ +#ifndef CONFIG_USER_ONLY +bool armv7m_nvic_neg_prio_requested(void *opaque, bool secure); +#else +static inline bool armv7m_nvic_neg_prio_requested(void *opaque, bool secure) +{ + return false; +} +#endif /* Interface for defining coprocessor registers. * Registers are defined in tables of arm_cp_reginfo structs @@ -XXX,XX +XXX,XX @@ static inline int cpu_mmu_index(CPUARMState *env, bool ifetch) if (arm_feature(env, ARM_FEATURE_M)) { ARMMMUIdx mmu_idx = el == 0 ? ARMMMUIdx_MUser : ARMMMUIdx_MPriv; - /* Execution priority is negative if FAULTMASK is set or - * we're in a HardFault or NMI handler. - */ - if ((env->v7m.exception > 0 && env->v7m.exception <= 3) - || env->v7m.faultmask[env->v7m.secure]) { + if (armv7m_nvic_neg_prio_requested(env->nvic, env->v7m.secure)) { mmu_idx = ARMMMUIdx_MNegPri; } diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static inline int nvic_exec_prio(NVICState *s) return MIN(running, s->exception_prio); } +bool armv7m_nvic_neg_prio_requested(void *opaque, bool secure) +{ + /* Return true if the requested execution priority is negative + * for the specified security state, ie that security state + * has an active NMI or HardFault or has set its FAULTMASK. + * Note that this is not the same as whether the execution + * priority is actually negative (for instance AIRCR.PRIS may + * mean we don't allow FAULTMASK_NS to actually make the execution + * priority negative). Compare pseudocode IsReqExcPriNeg(). + */ + NVICState *s = opaque; + + if (s->cpu->env.v7m.faultmask[secure]) { + return true; + } + + if (secure ? s->sec_vectors[ARMV7M_EXCP_HARD].active : + s->vectors[ARMV7M_EXCP_HARD].active) { + return true; + } + + if (s->vectors[ARMV7M_EXCP_NMI].active && + exc_targets_secure(s, ARMV7M_EXCP_NMI) == secure) { + return true; + } + + return false; +} + bool armv7m_nvic_can_take_pending_exception(void *opaque) { NVICState *s = opaque; -- 2.7.4 The ICSR NVIC register is banked for v8M. This doesn't require any new state, but it does mean that some bits are controlled by BFHNFNMINS and some bits must work with the correct banked exception. There is also a new in v8M PENDNMICLR bit. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-18-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 45 ++++++++++++++++++++++++++++++++------------- 1 file changed, 32 insertions(+), 13 deletions(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static uint32_t nvic_readl(NVICState *s, uint32_t offset, MemTxAttrs attrs) } case 0xd00: /* CPUID Base. */ return cpu->midr; - case 0xd04: /* Interrupt Control State. */ + case 0xd04: /* Interrupt Control State (ICSR) */ /* VECTACTIVE */ val = cpu->env.v7m.exception; /* VECTPENDING */ @@ -XXX,XX +XXX,XX @@ static uint32_t nvic_readl(NVICState *s, uint32_t offset, MemTxAttrs attrs) if (nvic_rettobase(s)) { val |= (1 << 11); } - /* PENDSTSET */ - if (s->vectors[ARMV7M_EXCP_SYSTICK].pending) { - val |= (1 << 26); - } - /* PENDSVSET */ - if (s->vectors[ARMV7M_EXCP_PENDSV].pending) { - val |= (1 << 28); + if (attrs.secure) { + /* PENDSTSET */ + if (s->sec_vectors[ARMV7M_EXCP_SYSTICK].pending) { + val |= (1 << 26); + } + /* PENDSVSET */ + if (s->sec_vectors[ARMV7M_EXCP_PENDSV].pending) { + val |= (1 << 28); + } + } else { + /* PENDSTSET */ + if (s->vectors[ARMV7M_EXCP_SYSTICK].pending) { + val |= (1 << 26); + } + /* PENDSVSET */ + if (s->vectors[ARMV7M_EXCP_PENDSV].pending) { + val |= (1 << 28); + } } /* NMIPENDSET */ - if (s->vectors[ARMV7M_EXCP_NMI].pending) { + if ((cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK) && + s->vectors[ARMV7M_EXCP_NMI].pending) { val |= (1 << 31); } - /* ISRPREEMPT not implemented */ + /* ISRPREEMPT: RES0 when halting debug not implemented */ + /* STTNS: RES0 for the Main Extension */ return val; case 0xd08: /* Vector Table Offset. */ return cpu->env.v7m.vecbase[attrs.secure]; @@ -XXX,XX +XXX,XX @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, nvic_irq_update(s); break; } - case 0xd04: /* Interrupt Control State. */ - if (value & (1 << 31)) { - armv7m_nvic_set_pending(s, ARMV7M_EXCP_NMI, false); + case 0xd04: /* Interrupt Control State (ICSR) */ + if (cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK) { + if (value & (1 << 31)) { + armv7m_nvic_set_pending(s, ARMV7M_EXCP_NMI, false); + } else if (value & (1 << 30) && + arm_feature(&cpu->env, ARM_FEATURE_V8)) { + /* PENDNMICLR didn't exist in v7M */ + armv7m_nvic_clear_pending(s, ARMV7M_EXCP_NMI, false); + } } if (value & (1 << 28)) { armv7m_nvic_set_pending(s, ARMV7M_EXCP_PENDSV, attrs.secure); -- 2.7.4 Handle banking of SHCSR: some register bits are banked between Secure and Non-Secure, and some are only accessible to Secure. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-19-git-send-email-peter.maydell@linaro.org --- hw/intc/armv7m_nvic.c | 221 ++++++++++++++++++++++++++++++++++++++------------ 1 file changed, 169 insertions(+), 52 deletions(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ static uint32_t nvic_readl(NVICState *s, uint32_t offset, MemTxAttrs attrs) val = cpu->env.v7m.ccr[attrs.secure]; val |= cpu->env.v7m.ccr[M_REG_NS] & R_V7M_CCR_BFHFNMIGN_MASK; return val; - case 0xd24: /* System Handler Status. */ + case 0xd24: /* System Handler Control and State (SHCSR) */ val = 0; - if (s->vectors[ARMV7M_EXCP_MEM].active) { - val |= (1 << 0); - } - if (s->vectors[ARMV7M_EXCP_BUS].active) { - val |= (1 << 1); - } - if (s->vectors[ARMV7M_EXCP_USAGE].active) { - val |= (1 << 3); + if (attrs.secure) { + if (s->sec_vectors[ARMV7M_EXCP_MEM].active) { + val |= (1 << 0); + } + if (s->sec_vectors[ARMV7M_EXCP_HARD].active) { + val |= (1 << 2); + } + if (s->sec_vectors[ARMV7M_EXCP_USAGE].active) { + val |= (1 << 3); + } + if (s->sec_vectors[ARMV7M_EXCP_SVC].active) { + val |= (1 << 7); + } + if (s->sec_vectors[ARMV7M_EXCP_PENDSV].active) { + val |= (1 << 10); + } + if (s->sec_vectors[ARMV7M_EXCP_SYSTICK].active) { + val |= (1 << 11); + } + if (s->sec_vectors[ARMV7M_EXCP_USAGE].pending) { + val |= (1 << 12); + } + if (s->sec_vectors[ARMV7M_EXCP_MEM].pending) { + val |= (1 << 13); + } + if (s->sec_vectors[ARMV7M_EXCP_SVC].pending) { + val |= (1 << 15); + } + if (s->sec_vectors[ARMV7M_EXCP_MEM].enabled) { + val |= (1 << 16); + } + if (s->sec_vectors[ARMV7M_EXCP_USAGE].enabled) { + val |= (1 << 18); + } + if (s->sec_vectors[ARMV7M_EXCP_HARD].pending) { + val |= (1 << 21); + } + /* SecureFault is not banked but is always RAZ/WI to NS */ + if (s->vectors[ARMV7M_EXCP_SECURE].active) { + val |= (1 << 4); + } + if (s->vectors[ARMV7M_EXCP_SECURE].enabled) { + val |= (1 << 19); + } + if (s->vectors[ARMV7M_EXCP_SECURE].pending) { + val |= (1 << 20); + } + } else { + if (s->vectors[ARMV7M_EXCP_MEM].active) { + val |= (1 << 0); + } + if (arm_feature(&cpu->env, ARM_FEATURE_V8)) { + /* HARDFAULTACT, HARDFAULTPENDED not present in v7M */ + if (s->vectors[ARMV7M_EXCP_HARD].active) { + val |= (1 << 2); + } + if (s->vectors[ARMV7M_EXCP_HARD].pending) { + val |= (1 << 21); + } + } + if (s->vectors[ARMV7M_EXCP_USAGE].active) { + val |= (1 << 3); + } + if (s->vectors[ARMV7M_EXCP_SVC].active) { + val |= (1 << 7); + } + if (s->vectors[ARMV7M_EXCP_PENDSV].active) { + val |= (1 << 10); + } + if (s->vectors[ARMV7M_EXCP_SYSTICK].active) { + val |= (1 << 11); + } + if (s->vectors[ARMV7M_EXCP_USAGE].pending) { + val |= (1 << 12); + } + if (s->vectors[ARMV7M_EXCP_MEM].pending) { + val |= (1 << 13); + } + if (s->vectors[ARMV7M_EXCP_SVC].pending) { + val |= (1 << 15); + } + if (s->vectors[ARMV7M_EXCP_MEM].enabled) { + val |= (1 << 16); + } + if (s->vectors[ARMV7M_EXCP_USAGE].enabled) { + val |= (1 << 18); + } } - if (s->vectors[ARMV7M_EXCP_SVC].active) { - val |= (1 << 7); + if (attrs.secure || (cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK)) { + if (s->vectors[ARMV7M_EXCP_BUS].active) { + val |= (1 << 1); + } + if (s->vectors[ARMV7M_EXCP_BUS].pending) { + val |= (1 << 14); + } + if (s->vectors[ARMV7M_EXCP_BUS].enabled) { + val |= (1 << 17); + } + if (arm_feature(&cpu->env, ARM_FEATURE_V8) && + s->vectors[ARMV7M_EXCP_NMI].active) { + /* NMIACT is not present in v7M */ + val |= (1 << 5); + } } + + /* TODO: this is RAZ/WI from NS if DEMCR.SDME is set */ if (s->vectors[ARMV7M_EXCP_DEBUG].active) { val |= (1 << 8); } - if (s->vectors[ARMV7M_EXCP_PENDSV].active) { - val |= (1 << 10); - } - if (s->vectors[ARMV7M_EXCP_SYSTICK].active) { - val |= (1 << 11); - } - if (s->vectors[ARMV7M_EXCP_USAGE].pending) { - val |= (1 << 12); - } - if (s->vectors[ARMV7M_EXCP_MEM].pending) { - val |= (1 << 13); - } - if (s->vectors[ARMV7M_EXCP_BUS].pending) { - val |= (1 << 14); - } - if (s->vectors[ARMV7M_EXCP_SVC].pending) { - val |= (1 << 15); - } - if (s->vectors[ARMV7M_EXCP_MEM].enabled) { - val |= (1 << 16); - } - if (s->vectors[ARMV7M_EXCP_BUS].enabled) { - val |= (1 << 17); - } - if (s->vectors[ARMV7M_EXCP_USAGE].enabled) { - val |= (1 << 18); - } return val; case 0xd28: /* Configurable Fault Status. */ /* The BFSR bits [15:8] are shared between security states @@ -XXX,XX +XXX,XX @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, cpu->env.v7m.ccr[attrs.secure] = value; break; - case 0xd24: /* System Handler Control. */ - s->vectors[ARMV7M_EXCP_MEM].active = (value & (1 << 0)) != 0; - s->vectors[ARMV7M_EXCP_BUS].active = (value & (1 << 1)) != 0; - s->vectors[ARMV7M_EXCP_USAGE].active = (value & (1 << 3)) != 0; - s->vectors[ARMV7M_EXCP_SVC].active = (value & (1 << 7)) != 0; + case 0xd24: /* System Handler Control and State (SHCSR) */ + if (attrs.secure) { + s->sec_vectors[ARMV7M_EXCP_MEM].active = (value & (1 << 0)) != 0; + /* Secure HardFault active bit cannot be written */ + s->sec_vectors[ARMV7M_EXCP_USAGE].active = (value & (1 << 3)) != 0; + s->sec_vectors[ARMV7M_EXCP_SVC].active = (value & (1 << 7)) != 0; + s->sec_vectors[ARMV7M_EXCP_PENDSV].active = + (value & (1 << 10)) != 0; + s->sec_vectors[ARMV7M_EXCP_SYSTICK].active = + (value & (1 << 11)) != 0; + s->sec_vectors[ARMV7M_EXCP_USAGE].pending = + (value & (1 << 12)) != 0; + s->sec_vectors[ARMV7M_EXCP_MEM].pending = (value & (1 << 13)) != 0; + s->sec_vectors[ARMV7M_EXCP_SVC].pending = (value & (1 << 15)) != 0; + s->sec_vectors[ARMV7M_EXCP_MEM].enabled = (value & (1 << 16)) != 0; + s->sec_vectors[ARMV7M_EXCP_BUS].enabled = (value & (1 << 17)) != 0; + s->sec_vectors[ARMV7M_EXCP_USAGE].enabled = + (value & (1 << 18)) != 0; + /* SecureFault not banked, but RAZ/WI to NS */ + s->vectors[ARMV7M_EXCP_SECURE].active = (value & (1 << 4)) != 0; + s->vectors[ARMV7M_EXCP_SECURE].enabled = (value & (1 << 19)) != 0; + s->vectors[ARMV7M_EXCP_SECURE].pending = (value & (1 << 20)) != 0; + } else { + s->vectors[ARMV7M_EXCP_MEM].active = (value & (1 << 0)) != 0; + if (arm_feature(&cpu->env, ARM_FEATURE_V8)) { + /* HARDFAULTPENDED is not present in v7M */ + s->vectors[ARMV7M_EXCP_HARD].pending = (value & (1 << 21)) != 0; + } + s->vectors[ARMV7M_EXCP_USAGE].active = (value & (1 << 3)) != 0; + s->vectors[ARMV7M_EXCP_SVC].active = (value & (1 << 7)) != 0; + s->vectors[ARMV7M_EXCP_PENDSV].active = (value & (1 << 10)) != 0; + s->vectors[ARMV7M_EXCP_SYSTICK].active = (value & (1 << 11)) != 0; + s->vectors[ARMV7M_EXCP_USAGE].pending = (value & (1 << 12)) != 0; + s->vectors[ARMV7M_EXCP_MEM].pending = (value & (1 << 13)) != 0; + s->vectors[ARMV7M_EXCP_SVC].pending = (value & (1 << 15)) != 0; + s->vectors[ARMV7M_EXCP_MEM].enabled = (value & (1 << 16)) != 0; + s->vectors[ARMV7M_EXCP_USAGE].enabled = (value & (1 << 18)) != 0; + } + if (attrs.secure || (cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK)) { + s->vectors[ARMV7M_EXCP_BUS].active = (value & (1 << 1)) != 0; + s->vectors[ARMV7M_EXCP_BUS].pending = (value & (1 << 14)) != 0; + s->vectors[ARMV7M_EXCP_BUS].enabled = (value & (1 << 17)) != 0; + } + /* NMIACT can only be written if the write is of a zero, with + * BFHFNMINS 1, and by the CPU in secure state via the NS alias. + */ + if (!attrs.secure && cpu->env.v7m.secure && + (cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK) && + (value & (1 << 5)) == 0) { + s->vectors[ARMV7M_EXCP_NMI].active = 0; + } + /* HARDFAULTACT can only be written if the write is of a zero + * to the non-secure HardFault state by the CPU in secure state. + * The only case where we can be targeting the non-secure HF state + * when in secure state is if this is a write via the NS alias + * and BFHFNMINS is 1. + */ + if (!attrs.secure && cpu->env.v7m.secure && + (cpu->env.v7m.aircr & R_V7M_AIRCR_BFHFNMINS_MASK) && + (value & (1 << 2)) == 0) { + s->vectors[ARMV7M_EXCP_HARD].active = 0; + } + + /* TODO: this is RAZ/WI from NS if DEMCR.SDME is set */ s->vectors[ARMV7M_EXCP_DEBUG].active = (value & (1 << 8)) != 0; - s->vectors[ARMV7M_EXCP_PENDSV].active = (value & (1 << 10)) != 0; - s->vectors[ARMV7M_EXCP_SYSTICK].active = (value & (1 << 11)) != 0; - s->vectors[ARMV7M_EXCP_USAGE].pending = (value & (1 << 12)) != 0; - s->vectors[ARMV7M_EXCP_MEM].pending = (value & (1 << 13)) != 0; - s->vectors[ARMV7M_EXCP_BUS].pending = (value & (1 << 14)) != 0; - s->vectors[ARMV7M_EXCP_SVC].pending = (value & (1 << 15)) != 0; - s->vectors[ARMV7M_EXCP_MEM].enabled = (value & (1 << 16)) != 0; - s->vectors[ARMV7M_EXCP_BUS].enabled = (value & (1 << 17)) != 0; - s->vectors[ARMV7M_EXCP_USAGE].enabled = (value & (1 << 18)) != 0; nvic_irq_update(s); break; case 0xd28: /* Configurable Fault Status. */ -- 2.7.4 Update armv7m_nvic_acknowledge_irq() and armv7m_nvic_complete_irq() to handle banked exceptions: * acknowledge needs to use the correct vector, which may be in sec_vectors[] * acknowledge needs to return to its caller whether the exception should be taken to secure or non-secure state * complete needs its caller to tell it whether the exception being completed is a secure one or not Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505240046-11454-20-git-send-email-peter.maydell@linaro.org --- target/arm/cpu.h | 15 +++++++++++++-- hw/intc/armv7m_nvic.c | 26 ++++++++++++++++++++------ target/arm/helper.c | 8 +++++--- hw/intc/trace-events | 4 ++-- 4 files changed, 40 insertions(+), 13 deletions(-) diff --git a/target/arm/cpu.h b/target/arm/cpu.h index XXXXXXX..XXXXXXX 100644 --- a/target/arm/cpu.h +++ b/target/arm/cpu.h @@ -XXX,XX +XXX,XX @@ static inline bool armv7m_nvic_can_take_pending_exception(void *opaque) * of architecturally banked exceptions. */ void armv7m_nvic_set_pending(void *opaque, int irq, bool secure); -void armv7m_nvic_acknowledge_irq(void *opaque); +/** + * armv7m_nvic_acknowledge_irq: make highest priority pending exception active + * @opaque: the NVIC + * + * Move the current highest priority pending exception from the pending + * state to the active state, and update v7m.exception to indicate that + * it is the exception currently being handled. + * + * Returns: true if exception should be taken to Secure state, false for NS + */ +bool armv7m_nvic_acknowledge_irq(void *opaque); /** * armv7m_nvic_complete_irq: complete specified interrupt or exception * @opaque: the NVIC * @irq: the exception number to complete + * @secure: true if this exception was secure * * Returns: -1 if the irq was not active * 1 if completing this irq brought us back to base (no active irqs) * 0 if there is still an irq active after this one was completed * (Ignoring -1, this is the same as the RETTOBASE value before completion.) */ -int armv7m_nvic_complete_irq(void *opaque, int irq); +int armv7m_nvic_complete_irq(void *opaque, int irq, bool secure); /** * armv7m_nvic_raw_execution_priority: return the raw execution priority * @opaque: the NVIC diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -XXX,XX +XXX,XX @@ void armv7m_nvic_set_pending(void *opaque, int irq, bool secure) } /* Make pending IRQ active. */ -void armv7m_nvic_acknowledge_irq(void *opaque) +bool armv7m_nvic_acknowledge_irq(void *opaque) { NVICState *s = (NVICState *)opaque; CPUARMState *env = &s->cpu->env; const int pending = s->vectpending; const int running = nvic_exec_prio(s); VecInfo *vec; + bool targets_secure; assert(pending > ARMV7M_EXCP_RESET && pending < s->num_irq); - vec = &s->vectors[pending]; + if (s->vectpending_is_s_banked) { + vec = &s->sec_vectors[pending]; + targets_secure = true; + } else { + vec = &s->vectors[pending]; + targets_secure = !exc_is_banked(s->vectpending) && + exc_targets_secure(s, s->vectpending); + } assert(vec->enabled); assert(vec->pending); assert(s->vectpending_prio < running); - trace_nvic_acknowledge_irq(pending, s->vectpending_prio); + trace_nvic_acknowledge_irq(pending, s->vectpending_prio, targets_secure); vec->active = 1; vec->pending = 0; @@ -XXX,XX +XXX,XX @@ void armv7m_nvic_acknowledge_irq(void *opaque) env->v7m.exception = s->vectpending; nvic_irq_update(s); + + return targets_secure; } -int armv7m_nvic_complete_irq(void *opaque, int irq) +int armv7m_nvic_complete_irq(void *opaque, int irq, bool secure) { NVICState *s = (NVICState *)opaque; VecInfo *vec; @@ -XXX,XX +XXX,XX @@ int armv7m_nvic_complete_irq(void *opaque, int irq) assert(irq > ARMV7M_EXCP_RESET && irq < s->num_irq); - vec = &s->vectors[irq]; + if (secure && exc_is_banked(irq)) { + vec = &s->sec_vectors[irq]; + } else { + vec = &s->vectors[irq]; + } - trace_nvic_complete_irq(irq); + trace_nvic_complete_irq(irq, secure); if (!vec->active) { /* Tell the caller this was an illegal exception return */ diff --git a/target/arm/helper.c b/target/arm/helper.c index XXXXXXX..XXXXXXX 100644 --- a/target/arm/helper.c +++ b/target/arm/helper.c @@ -XXX,XX +XXX,XX @@ static void do_v7m_exception_exit(ARMCPU *cpu) bool return_to_sp_process = false; bool return_to_handler = false; bool rettobase = false; + bool exc_secure = false; /* We can only get here from an EXCP_EXCEPTION_EXIT, and * gen_bx_excret() enforces the architectural rule @@ -XXX,XX +XXX,XX @@ static void do_v7m_exception_exit(ARMCPU *cpu) * which security state's faultmask to clear. (v8M ARM ARM R_KBNF.) */ if (arm_feature(env, ARM_FEATURE_M_SECURITY)) { - int es = excret & R_V7M_EXCRET_ES_MASK; + exc_secure = excret & R_V7M_EXCRET_ES_MASK; if (armv7m_nvic_raw_execution_priority(env->nvic) >= 0) { - env->v7m.faultmask[es] = 0; + env->v7m.faultmask[exc_secure] = 0; } } else { env->v7m.faultmask[M_REG_NS] = 0; } } - switch (armv7m_nvic_complete_irq(env->nvic, env->v7m.exception)) { + switch (armv7m_nvic_complete_irq(env->nvic, env->v7m.exception, + exc_secure)) { case -1: /* attempt to exit an exception that isn't active */ ufault = true; diff --git a/hw/intc/trace-events b/hw/intc/trace-events index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/trace-events +++ b/hw/intc/trace-events @@ -XXX,XX +XXX,XX @@ nvic_escalate_disabled(int irq) "NVIC escalating irq %d to HardFault: disabled" nvic_set_pending(int irq, bool secure, int en, int prio) "NVIC set pending irq %d secure-bank %d (enabled: %d priority %d)" nvic_clear_pending(int irq, bool secure, int en, int prio) "NVIC clear pending irq %d secure-bank %d (enabled: %d priority %d)" nvic_set_pending_level(int irq) "NVIC set pending: irq %d higher prio than vectpending: setting irq line to 1" -nvic_acknowledge_irq(int irq, int prio) "NVIC acknowledge IRQ: %d now active (prio %d)" -nvic_complete_irq(int irq) "NVIC complete IRQ %d" +nvic_acknowledge_irq(int irq, int prio, bool targets_secure) "NVIC acknowledge IRQ: %d now active (prio %d targets_secure %d)" +nvic_complete_irq(int irq, bool secure) "NVIC complete IRQ %d (secure %d)" nvic_set_irq_level(int irq, int level) "NVIC external irq %d level set to %d" nvic_sysreg_read(uint64_t addr, uint32_t value, unsigned size) "NVIC sysreg read addr 0x%" PRIx64 " data 0x%" PRIx32 " size %u" nvic_sysreg_write(uint64_t addr, uint32_t value, unsigned size) "NVIC sysreg write addr 0x%" PRIx64 " data 0x%" PRIx32 " size %u" -- 2.7.4 In the A64 decoder, we have a lot of references to section numbers from version A.a of the v8A ARM ARM (DDI0487). This version of the document is now long obsolete (we are currently on revision B.a), and various intervening versions renumbered all the sections. The most recent B.a version of the document doesn't assign section numbers at all to the individual instruction classes in the way that the various A.x versions did. The simplest thing to do is just to delete all the out of date C.x.x references. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Message-id: 20170915150849.23557-1-peter.maydell@linaro.org --- target/arm/translate-a64.c | 227 +++++++++++++++++++++++---------------------- 1 file changed, 114 insertions(+), 113 deletions(-) diff --git a/target/arm/translate-a64.c b/target/arm/translate-a64.c index XXXXXXX..XXXXXXX 100644 --- a/target/arm/translate-a64.c +++ b/target/arm/translate-a64.c @@ -XXX,XX +XXX,XX @@ static inline AArch64DecodeFn *lookup_disas_fn(const AArch64DecodeTable *table, } /* - * the instruction disassembly implemented here matches - * the instruction encoding classifications in chapter 3 (C3) - * of the ARM Architecture Reference Manual (DDI0487A_a) + * The instruction disassembly implemented here matches + * the instruction encoding classifications in chapter C4 + * of the ARM Architecture Reference Manual (DDI0487B_a); + * classification names and decode diagrams here should generally + * match up with those in the manual. */ -/* C3.2.7 Unconditional branch (immediate) +/* Unconditional branch (immediate) * 31 30 26 25 0 * +----+-----------+-------------------------------------+ * | op | 0 0 1 0 1 | imm26 | @@ -XXX,XX +XXX,XX @@ static void disas_uncond_b_imm(DisasContext *s, uint32_t insn) uint64_t addr = s->pc + sextract32(insn, 0, 26) * 4 - 4; if (insn & (1U << 31)) { - /* C5.6.26 BL Branch with link */ + /* BL Branch with link */ tcg_gen_movi_i64(cpu_reg(s, 30), s->pc); } - /* C5.6.20 B Branch / C5.6.26 BL Branch with link */ + /* B Branch / BL Branch with link */ gen_goto_tb(s, 0, addr); } -/* C3.2.1 Compare & branch (immediate) +/* Compare and branch (immediate) * 31 30 25 24 23 5 4 0 * +----+-------------+----+---------------------+--------+ * | sf | 0 1 1 0 1 0 | op | imm19 | Rt | @@ -XXX,XX +XXX,XX @@ static void disas_comp_b_imm(DisasContext *s, uint32_t insn) gen_goto_tb(s, 1, addr); } -/* C3.2.5 Test & branch (immediate) +/* Test and branch (immediate) * 31 30 25 24 23 19 18 5 4 0 * +----+-------------+----+-------+-------------+------+ * | b5 | 0 1 1 0 1 1 | op | b40 | imm14 | Rt | @@ -XXX,XX +XXX,XX @@ static void disas_test_b_imm(DisasContext *s, uint32_t insn) gen_goto_tb(s, 1, addr); } -/* C3.2.2 / C5.6.19 Conditional branch (immediate) +/* Conditional branch (immediate) * 31 25 24 23 5 4 3 0 * +---------------+----+---------------------+----+------+ * | 0 1 0 1 0 1 0 | o1 | imm19 | o0 | cond | @@ -XXX,XX +XXX,XX @@ static void disas_cond_b_imm(DisasContext *s, uint32_t insn) } } -/* C5.6.68 HINT */ +/* HINT instruction group, including various allocated HINTs */ static void handle_hint(DisasContext *s, uint32_t insn, unsigned int op1, unsigned int op2, unsigned int crm) { @@ -XXX,XX +XXX,XX @@ static void handle_sync(DisasContext *s, uint32_t insn, } } -/* C5.6.130 MSR (immediate) - move immediate to processor state field */ +/* MSR (immediate) - move immediate to processor state field */ static void handle_msr_i(DisasContext *s, uint32_t insn, unsigned int op1, unsigned int op2, unsigned int crm) { @@ -XXX,XX +XXX,XX @@ static void gen_set_nzcv(TCGv_i64 tcg_rt) tcg_temp_free_i32(nzcv); } -/* C5.6.129 MRS - move from system register - * C5.6.131 MSR (register) - move to system register - * C5.6.204 SYS - * C5.6.205 SYSL +/* MRS - move from system register + * MSR (register) - move to system register + * SYS + * SYSL * These are all essentially the same insn in 'read' and 'write' * versions, with varying op0 fields. */ @@ -XXX,XX +XXX,XX @@ static void handle_sys(DisasContext *s, uint32_t insn, bool isread, } } -/* C3.2.4 System +/* System * 31 22 21 20 19 18 16 15 12 11 8 7 5 4 0 * +---------------------+---+-----+-----+-------+-------+-----+------+ * | 1 1 0 1 0 1 0 1 0 0 | L | op0 | op1 | CRn | CRm | op2 | Rt | @@ -XXX,XX +XXX,XX @@ static void disas_system(DisasContext *s, uint32_t insn) return; } switch (crn) { - case 2: /* C5.6.68 HINT */ + case 2: /* HINT (including allocated hints like NOP, YIELD, etc) */ handle_hint(s, insn, op1, op2, crm); break; case 3: /* CLREX, DSB, DMB, ISB */ handle_sync(s, insn, op1, op2, crm); break; - case 4: /* C5.6.130 MSR (immediate) */ + case 4: /* MSR (immediate) */ handle_msr_i(s, insn, op1, op2, crm); break; default: @@ -XXX,XX +XXX,XX @@ static void disas_system(DisasContext *s, uint32_t insn) handle_sys(s, insn, l, op0, op1, op2, crn, crm, rt); } -/* C3.2.3 Exception generation +/* Exception generation * * 31 24 23 21 20 5 4 2 1 0 * +-----------------+-----+------------------------+-----+----+ @@ -XXX,XX +XXX,XX @@ static void disas_exc(DisasContext *s, uint32_t insn) } } -/* C3.2.7 Unconditional branch (register) +/* Unconditional branch (register) * 31 25 24 21 20 16 15 10 9 5 4 0 * +---------------+-------+-------+-------+------+-------+ * | 1 1 0 1 0 1 1 | opc | op2 | op3 | Rn | op4 | @@ -XXX,XX +XXX,XX @@ static void disas_uncond_b_reg(DisasContext *s, uint32_t insn) s->base.is_jmp = DISAS_JUMP; } -/* C3.2 Branches, exception generating and system instructions */ +/* Branches, exception generating and system instructions */ static void disas_b_exc_sys(DisasContext *s, uint32_t insn) { switch (extract32(insn, 25, 7)) { @@ -XXX,XX +XXX,XX @@ static bool disas_ldst_compute_iss_sf(int size, bool is_signed, int opc) return regsize == 64; } -/* C3.3.6 Load/store exclusive +/* Load/store exclusive * * 31 30 29 24 23 22 21 20 16 15 14 10 9 5 4 0 * +-----+-------------+----+---+----+------+----+-------+------+------+ @@ -XXX,XX +XXX,XX @@ static void disas_ldst_excl(DisasContext *s, uint32_t insn) } /* - * C3.3.5 Load register (literal) + * Load register (literal) * * 31 30 29 27 26 25 24 23 5 4 0 * +-----+-------+---+-----+-------------------+-------+ @@ -XXX,XX +XXX,XX @@ static void disas_ld_lit(DisasContext *s, uint32_t insn) } /* - * C5.6.80 LDNP (Load Pair - non-temporal hint) - * C5.6.81 LDP (Load Pair - non vector) - * C5.6.82 LDPSW (Load Pair Signed Word - non vector) - * C5.6.176 STNP (Store Pair - non-temporal hint) - * C5.6.177 STP (Store Pair - non vector) - * C6.3.165 LDNP (Load Pair of SIMD&FP - non-temporal hint) - * C6.3.165 LDP (Load Pair of SIMD&FP) - * C6.3.284 STNP (Store Pair of SIMD&FP - non-temporal hint) - * C6.3.284 STP (Store Pair of SIMD&FP) + * LDNP (Load Pair - non-temporal hint) + * LDP (Load Pair - non vector) + * LDPSW (Load Pair Signed Word - non vector) + * STNP (Store Pair - non-temporal hint) + * STP (Store Pair - non vector) + * LDNP (Load Pair of SIMD&FP - non-temporal hint) + * LDP (Load Pair of SIMD&FP) + * STNP (Store Pair of SIMD&FP - non-temporal hint) + * STP (Store Pair of SIMD&FP) * * 31 30 29 27 26 25 24 23 22 21 15 14 10 9 5 4 0 * +-----+-------+---+---+-------+---+-----------------------------+ @@ -XXX,XX +XXX,XX @@ static void disas_ldst_pair(DisasContext *s, uint32_t insn) } /* - * C3.3.8 Load/store (immediate post-indexed) - * C3.3.9 Load/store (immediate pre-indexed) - * C3.3.12 Load/store (unscaled immediate) + * Load/store (immediate post-indexed) + * Load/store (immediate pre-indexed) + * Load/store (unscaled immediate) * * 31 30 29 27 26 25 24 23 22 21 20 12 11 10 9 5 4 0 * +----+-------+---+-----+-----+---+--------+-----+------+------+ @@ -XXX,XX +XXX,XX @@ static void disas_ldst_reg_imm9(DisasContext *s, uint32_t insn, } /* - * C3.3.10 Load/store (register offset) + * Load/store (register offset) * * 31 30 29 27 26 25 24 23 22 21 20 16 15 13 12 11 10 9 5 4 0 * +----+-------+---+-----+-----+---+------+-----+--+-----+----+----+ @@ -XXX,XX +XXX,XX @@ static void disas_ldst_reg_roffset(DisasContext *s, uint32_t insn, } /* - * C3.3.13 Load/store (unsigned immediate) + * Load/store (unsigned immediate) * * 31 30 29 27 26 25 24 23 22 21 10 9 5 * +----+-------+---+-----+-----+------------+-------+------+ @@ -XXX,XX +XXX,XX @@ static void disas_ldst_reg(DisasContext *s, uint32_t insn) } } -/* C3.3.1 AdvSIMD load/store multiple structures +/* AdvSIMD load/store multiple structures * * 31 30 29 23 22 21 16 15 12 11 10 9 5 4 0 * +---+---+---------------+---+-------------+--------+------+------+------+ * | 0 | Q | 0 0 1 1 0 0 0 | L | 0 0 0 0 0 0 | opcode | size | Rn | Rt | * +---+---+---------------+---+-------------+--------+------+------+------+ * - * C3.3.2 AdvSIMD load/store multiple structures (post-indexed) + * AdvSIMD load/store multiple structures (post-indexed) * * 31 30 29 23 22 21 20 16 15 12 11 10 9 5 4 0 * +---+---+---------------+---+---+---------+--------+------+------+------+ @@ -XXX,XX +XXX,XX @@ static void disas_ldst_multiple_struct(DisasContext *s, uint32_t insn) tcg_temp_free_i64(tcg_addr); } -/* C3.3.3 AdvSIMD load/store single structure +/* AdvSIMD load/store single structure * * 31 30 29 23 22 21 20 16 15 13 12 11 10 9 5 4 0 * +---+---+---------------+-----+-----------+-----+---+------+------+------+ * | 0 | Q | 0 0 1 1 0 1 0 | L R | 0 0 0 0 0 | opc | S | size | Rn | Rt | * +---+---+---------------+-----+-----------+-----+---+------+------+------+ * - * C3.3.4 AdvSIMD load/store single structure (post-indexed) + * AdvSIMD load/store single structure (post-indexed) * * 31 30 29 23 22 21 20 16 15 13 12 11 10 9 5 4 0 * +---+---+---------------+-----+-----------+-----+---+------+------+------+ @@ -XXX,XX +XXX,XX @@ static void disas_ldst_single_struct(DisasContext *s, uint32_t insn) tcg_temp_free_i64(tcg_addr); } -/* C3.3 Loads and stores */ +/* Loads and stores */ static void disas_ldst(DisasContext *s, uint32_t insn) { switch (extract32(insn, 24, 6)) { @@ -XXX,XX +XXX,XX @@ static void disas_ldst(DisasContext *s, uint32_t insn) } } -/* C3.4.6 PC-rel. addressing +/* PC-rel. addressing * 31 30 29 28 24 23 5 4 0 * +----+-------+-----------+-------------------+------+ * | op | immlo | 1 0 0 0 0 | immhi | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_pc_rel_adr(DisasContext *s, uint32_t insn) } /* - * C3.4.1 Add/subtract (immediate) + * Add/subtract (immediate) * * 31 30 29 28 24 23 22 21 10 9 5 4 0 * +--+--+--+-----------+-----+-------------+-----+-----+ @@ -XXX,XX +XXX,XX @@ static bool logic_imm_decode_wmask(uint64_t *result, unsigned int immn, return true; } -/* C3.4.4 Logical (immediate) +/* Logical (immediate) * 31 30 29 28 23 22 21 16 15 10 9 5 4 0 * +----+-----+-------------+---+------+------+------+------+ * | sf | opc | 1 0 0 1 0 0 | N | immr | imms | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_logic_imm(DisasContext *s, uint32_t insn) } /* - * C3.4.5 Move wide (immediate) + * Move wide (immediate) * * 31 30 29 28 23 22 21 20 5 4 0 * +--+-----+-------------+-----+----------------+------+ @@ -XXX,XX +XXX,XX @@ static void disas_movw_imm(DisasContext *s, uint32_t insn) } } -/* C3.4.2 Bitfield +/* Bitfield * 31 30 29 28 23 22 21 16 15 10 9 5 4 0 * +----+-----+-------------+---+------+------+------+------+ * | sf | opc | 1 0 0 1 1 0 | N | immr | imms | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_bitfield(DisasContext *s, uint32_t insn) } } -/* C3.4.3 Extract +/* Extract * 31 30 29 28 23 22 21 20 16 15 10 9 5 4 0 * +----+------+-------------+---+----+------+--------+------+------+ * | sf | op21 | 1 0 0 1 1 1 | N | o0 | Rm | imms | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_extract(DisasContext *s, uint32_t insn) } } -/* C3.4 Data processing - immediate */ +/* Data processing - immediate */ static void disas_data_proc_imm(DisasContext *s, uint32_t insn) { switch (extract32(insn, 23, 6)) { @@ -XXX,XX +XXX,XX @@ static void shift_reg_imm(TCGv_i64 dst, TCGv_i64 src, int sf, } } -/* C3.5.10 Logical (shifted register) +/* Logical (shifted register) * 31 30 29 28 24 23 22 21 20 16 15 10 9 5 4 0 * +----+-----+-----------+-------+---+------+--------+------+------+ * | sf | opc | 0 1 0 1 0 | shift | N | Rm | imm6 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_logic_reg(DisasContext *s, uint32_t insn) } /* - * C3.5.1 Add/subtract (extended register) + * Add/subtract (extended register) * * 31|30|29|28 24|23 22|21|20 16|15 13|12 10|9 5|4 0| * +--+--+--+-----------+-----+--+-------+------+------+----+----+ @@ -XXX,XX +XXX,XX @@ static void disas_add_sub_ext_reg(DisasContext *s, uint32_t insn) } /* - * C3.5.2 Add/subtract (shifted register) + * Add/subtract (shifted register) * * 31 30 29 28 24 23 22 21 20 16 15 10 9 5 4 0 * +--+--+--+-----------+-----+--+-------+---------+------+------+ @@ -XXX,XX +XXX,XX @@ static void disas_add_sub_reg(DisasContext *s, uint32_t insn) tcg_temp_free_i64(tcg_result); } -/* C3.5.9 Data-processing (3 source) - - 31 30 29 28 24 23 21 20 16 15 14 10 9 5 4 0 - +--+------+-----------+------+------+----+------+------+------+ - |sf| op54 | 1 1 0 1 1 | op31 | Rm | o0 | Ra | Rn | Rd | - +--+------+-----------+------+------+----+------+------+------+ - +/* Data-processing (3 source) + * + * 31 30 29 28 24 23 21 20 16 15 14 10 9 5 4 0 + * +--+------+-----------+------+------+----+------+------+------+ + * |sf| op54 | 1 1 0 1 1 | op31 | Rm | o0 | Ra | Rn | Rd | + * +--+------+-----------+------+------+----+------+------+------+ */ static void disas_data_proc_3src(DisasContext *s, uint32_t insn) { @@ -XXX,XX +XXX,XX @@ static void disas_data_proc_3src(DisasContext *s, uint32_t insn) tcg_temp_free_i64(tcg_tmp); } -/* C3.5.3 - Add/subtract (with carry) +/* Add/subtract (with carry) * 31 30 29 28 27 26 25 24 23 22 21 20 16 15 10 9 5 4 0 * +--+--+--+------------------------+------+---------+------+-----+ * |sf|op| S| 1 1 0 1 0 0 0 0 | rm | opcode2 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_adc_sbc(DisasContext *s, uint32_t insn) } } -/* C3.5.4 - C3.5.5 Conditional compare (immediate / register) +/* Conditional compare (immediate / register) * 31 30 29 28 27 26 25 24 23 22 21 20 16 15 12 11 10 9 5 4 3 0 * +--+--+--+------------------------+--------+------+----+--+------+--+-----+ * |sf|op| S| 1 1 0 1 0 0 1 0 |imm5/rm | cond |i/r |o2| Rn |o3|nzcv | @@ -XXX,XX +XXX,XX @@ static void disas_cc(DisasContext *s, uint32_t insn) tcg_temp_free_i32(tcg_t2); } -/* C3.5.6 Conditional select +/* Conditional select * 31 30 29 28 21 20 16 15 12 11 10 9 5 4 0 * +----+----+---+-----------------+------+------+-----+------+------+ * | sf | op | S | 1 1 0 1 0 1 0 0 | Rm | cond | op2 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_rbit(DisasContext *s, unsigned int sf, } } -/* C5.6.149 REV with sf==1, opcode==3 ("REV64") */ +/* REV with sf==1, opcode==3 ("REV64") */ static void handle_rev64(DisasContext *s, unsigned int sf, unsigned int rn, unsigned int rd) { @@ -XXX,XX +XXX,XX @@ static void handle_rev64(DisasContext *s, unsigned int sf, tcg_gen_bswap64_i64(cpu_reg(s, rd), cpu_reg(s, rn)); } -/* C5.6.149 REV with sf==0, opcode==2 - * C5.6.151 REV32 (sf==1, opcode==2) +/* REV with sf==0, opcode==2 + * REV32 (sf==1, opcode==2) */ static void handle_rev32(DisasContext *s, unsigned int sf, unsigned int rn, unsigned int rd) @@ -XXX,XX +XXX,XX @@ static void handle_rev32(DisasContext *s, unsigned int sf, } } -/* C5.6.150 REV16 (opcode==1) */ +/* REV16 (opcode==1) */ static void handle_rev16(DisasContext *s, unsigned int sf, unsigned int rn, unsigned int rd) { @@ -XXX,XX +XXX,XX @@ static void handle_rev16(DisasContext *s, unsigned int sf, tcg_temp_free_i64(tcg_tmp); } -/* C3.5.7 Data-processing (1 source) +/* Data-processing (1 source) * 31 30 29 28 21 20 16 15 10 9 5 4 0 * +----+---+---+-----------------+---------+--------+------+------+ * | sf | 1 | S | 1 1 0 1 0 1 1 0 | opcode2 | opcode | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_div(DisasContext *s, bool is_signed, unsigned int sf, } } -/* C5.6.115 LSLV, C5.6.118 LSRV, C5.6.17 ASRV, C5.6.154 RORV */ +/* LSLV, LSRV, ASRV, RORV */ static void handle_shift_reg(DisasContext *s, enum a64_shift_type shift_type, unsigned int sf, unsigned int rm, unsigned int rn, unsigned int rd) @@ -XXX,XX +XXX,XX @@ static void handle_crc32(DisasContext *s, tcg_temp_free_i32(tcg_bytes); } -/* C3.5.8 Data-processing (2 source) +/* Data-processing (2 source) * 31 30 29 28 21 20 16 15 10 9 5 4 0 * +----+---+---+-----------------+------+--------+------+------+ * | sf | 0 | S | 1 1 0 1 0 1 1 0 | Rm | opcode | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_data_proc_2src(DisasContext *s, uint32_t insn) } } -/* C3.5 Data processing - register */ +/* Data processing - register */ static void disas_data_proc_reg(DisasContext *s, uint32_t insn) { switch (extract32(insn, 24, 5)) { @@ -XXX,XX +XXX,XX @@ static void handle_fp_compare(DisasContext *s, bool is_double, tcg_temp_free_i64(tcg_flags); } -/* C3.6.22 Floating point compare +/* Floating point compare * 31 30 29 28 24 23 22 21 20 16 15 14 13 10 9 5 4 0 * +---+---+---+-----------+------+---+------+-----+---------+------+-------+ * | M | 0 | S | 1 1 1 1 0 | type | 1 | Rm | op | 1 0 0 0 | Rn | op2 | @@ -XXX,XX +XXX,XX @@ static void disas_fp_compare(DisasContext *s, uint32_t insn) handle_fp_compare(s, type, rn, rm, opc & 1, opc & 2); } -/* C3.6.23 Floating point conditional compare +/* Floating point conditional compare * 31 30 29 28 24 23 22 21 20 16 15 12 11 10 9 5 4 3 0 * +---+---+---+-----------+------+---+------+------+-----+------+----+------+ * | M | 0 | S | 1 1 1 1 0 | type | 1 | Rm | cond | 0 1 | Rn | op | nzcv | @@ -XXX,XX +XXX,XX @@ static void disas_fp_ccomp(DisasContext *s, uint32_t insn) } } -/* C3.6.24 Floating point conditional select +/* Floating point conditional select * 31 30 29 28 24 23 22 21 20 16 15 12 11 10 9 5 4 0 * +---+---+---+-----------+------+---+------+------+-----+------+------+ * | M | 0 | S | 1 1 1 1 0 | type | 1 | Rm | cond | 1 1 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_fp_csel(DisasContext *s, uint32_t insn) tcg_temp_free_i64(t_true); } -/* C3.6.25 Floating-point data-processing (1 source) - single precision */ +/* Floating-point data-processing (1 source) - single precision */ static void handle_fp_1src_single(DisasContext *s, int opcode, int rd, int rn) { TCGv_ptr fpst; @@ -XXX,XX +XXX,XX @@ static void handle_fp_1src_single(DisasContext *s, int opcode, int rd, int rn) tcg_temp_free_i32(tcg_res); } -/* C3.6.25 Floating-point data-processing (1 source) - double precision */ +/* Floating-point data-processing (1 source) - double precision */ static void handle_fp_1src_double(DisasContext *s, int opcode, int rd, int rn) { TCGv_ptr fpst; @@ -XXX,XX +XXX,XX @@ static void handle_fp_fcvt(DisasContext *s, int opcode, } } -/* C3.6.25 Floating point data-processing (1 source) +/* Floating point data-processing (1 source) * 31 30 29 28 24 23 22 21 20 15 14 10 9 5 4 0 * +---+---+---+-----------+------+---+--------+-----------+------+------+ * | M | 0 | S | 1 1 1 1 0 | type | 1 | opcode | 1 0 0 0 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_fp_1src(DisasContext *s, uint32_t insn) } } -/* C3.6.26 Floating-point data-processing (2 source) - single precision */ +/* Floating-point data-processing (2 source) - single precision */ static void handle_fp_2src_single(DisasContext *s, int opcode, int rd, int rn, int rm) { @@ -XXX,XX +XXX,XX @@ static void handle_fp_2src_single(DisasContext *s, int opcode, tcg_temp_free_i32(tcg_res); } -/* C3.6.26 Floating-point data-processing (2 source) - double precision */ +/* Floating-point data-processing (2 source) - double precision */ static void handle_fp_2src_double(DisasContext *s, int opcode, int rd, int rn, int rm) { @@ -XXX,XX +XXX,XX @@ static void handle_fp_2src_double(DisasContext *s, int opcode, tcg_temp_free_i64(tcg_res); } -/* C3.6.26 Floating point data-processing (2 source) +/* Floating point data-processing (2 source) * 31 30 29 28 24 23 22 21 20 16 15 12 11 10 9 5 4 0 * +---+---+---+-----------+------+---+------+--------+-----+------+------+ * | M | 0 | S | 1 1 1 1 0 | type | 1 | Rm | opcode | 1 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_fp_2src(DisasContext *s, uint32_t insn) } } -/* C3.6.27 Floating-point data-processing (3 source) - single precision */ +/* Floating-point data-processing (3 source) - single precision */ static void handle_fp_3src_single(DisasContext *s, bool o0, bool o1, int rd, int rn, int rm, int ra) { @@ -XXX,XX +XXX,XX @@ static void handle_fp_3src_single(DisasContext *s, bool o0, bool o1, tcg_temp_free_i32(tcg_res); } -/* C3.6.27 Floating-point data-processing (3 source) - double precision */ +/* Floating-point data-processing (3 source) - double precision */ static void handle_fp_3src_double(DisasContext *s, bool o0, bool o1, int rd, int rn, int rm, int ra) { @@ -XXX,XX +XXX,XX @@ static void handle_fp_3src_double(DisasContext *s, bool o0, bool o1, tcg_temp_free_i64(tcg_res); } -/* C3.6.27 Floating point data-processing (3 source) +/* Floating point data-processing (3 source) * 31 30 29 28 24 23 22 21 20 16 15 14 10 9 5 4 0 * +---+---+---+-----------+------+----+------+----+------+------+------+ * | M | 0 | S | 1 1 1 1 1 | type | o1 | Rm | o0 | Ra | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_fp_3src(DisasContext *s, uint32_t insn) } } -/* C3.6.28 Floating point immediate +/* Floating point immediate * 31 30 29 28 24 23 22 21 20 13 12 10 9 5 4 0 * +---+---+---+-----------+------+---+------------+-------+------+------+ * | M | 0 | S | 1 1 1 1 0 | type | 1 | imm8 | 1 0 0 | imm5 | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_fpfpcvt(DisasContext *s, int rd, int rn, int opcode, tcg_temp_free_i32(tcg_shift); } -/* C3.6.29 Floating point <-> fixed point conversions +/* Floating point <-> fixed point conversions * 31 30 29 28 24 23 22 21 20 19 18 16 15 10 9 5 4 0 * +----+---+---+-----------+------+---+-------+--------+-------+------+------+ * | sf | 0 | S | 1 1 1 1 0 | type | 0 | rmode | opcode | scale | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_fmov(DisasContext *s, int rd, int rn, int type, bool itof) } } -/* C3.6.30 Floating point <-> integer conversions +/* Floating point <-> integer conversions * 31 30 29 28 24 23 22 21 20 19 18 16 15 10 9 5 4 0 * +----+---+---+-----------+------+---+-------+-----+-------------+----+----+ * | sf | 0 | S | 1 1 1 1 0 | type | 1 | rmode | opc | 0 0 0 0 0 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void do_ext64(DisasContext *s, TCGv_i64 tcg_left, TCGv_i64 tcg_right, tcg_temp_free_i64(tcg_tmp); } -/* C3.6.1 EXT +/* EXT * 31 30 29 24 23 22 21 20 16 15 14 11 10 9 5 4 0 * +---+---+-------------+-----+---+------+---+------+---+------+------+ * | 0 | Q | 1 0 1 1 1 0 | op2 | 0 | Rm | 0 | imm4 | 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_ext(DisasContext *s, uint32_t insn) tcg_temp_free_i64(tcg_resh); } -/* C3.6.2 TBL/TBX +/* TBL/TBX * 31 30 29 24 23 22 21 20 16 15 14 13 12 11 10 9 5 4 0 * +---+---+-------------+-----+---+------+---+-----+----+-----+------+------+ * | 0 | Q | 0 0 1 1 1 0 | op2 | 0 | Rm | 0 | len | op | 0 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_tb(DisasContext *s, uint32_t insn) tcg_temp_free_i64(tcg_resh); } -/* C3.6.3 ZIP/UZP/TRN +/* ZIP/UZP/TRN * 31 30 29 24 23 22 21 20 16 15 14 12 11 10 9 5 4 0 * +---+---+-------------+------+---+------+---+------------------+------+ * | 0 | Q | 0 0 1 1 1 0 | size | 0 | Rm | 0 | opc | 1 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void do_minmaxop(DisasContext *s, TCGv_i32 tcg_elt1, TCGv_i32 tcg_elt2, } } -/* C3.6.4 AdvSIMD across lanes +/* AdvSIMD across lanes * 31 30 29 28 24 23 22 21 17 16 12 11 10 9 5 4 0 * +---+---+---+-----------+------+-----------+--------+-----+------+------+ * | 0 | Q | U | 0 1 1 1 0 | size | 1 1 0 0 0 | opcode | 1 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_across_lanes(DisasContext *s, uint32_t insn) tcg_temp_free_i64(tcg_res); } -/* C6.3.31 DUP (Element, Vector) +/* DUP (Element, Vector) * * 31 30 29 21 20 16 15 10 9 5 4 0 * +---+---+-------------------+--------+-------------+------+------+ @@ -XXX,XX +XXX,XX @@ static void handle_simd_dupe(DisasContext *s, int is_q, int rd, int rn, tcg_temp_free_i64(tmp); } -/* C6.3.31 DUP (element, scalar) +/* DUP (element, scalar) * 31 21 20 16 15 10 9 5 4 0 * +-----------------------+--------+-------------+------+------+ * | 0 1 0 1 1 1 1 0 0 0 0 | imm5 | 0 0 0 0 0 1 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_simd_dupes(DisasContext *s, int rd, int rn, tcg_temp_free_i64(tmp); } -/* C6.3.32 DUP (General) +/* DUP (General) * * 31 30 29 21 20 16 15 10 9 5 4 0 * +---+---+-------------------+--------+-------------+------+------+ @@ -XXX,XX +XXX,XX @@ static void handle_simd_dupg(DisasContext *s, int is_q, int rd, int rn, } } -/* C6.3.150 INS (Element) +/* INS (Element) * * 31 21 20 16 15 14 11 10 9 5 4 0 * +-----------------------+--------+------------+---+------+------+ @@ -XXX,XX +XXX,XX @@ static void handle_simd_inse(DisasContext *s, int rd, int rn, } -/* C6.3.151 INS (General) +/* INS (General) * * 31 21 20 16 15 10 9 5 4 0 * +-----------------------+--------+-------------+------+------+ @@ -XXX,XX +XXX,XX @@ static void handle_simd_insg(DisasContext *s, int rd, int rn, int imm5) } /* - * C6.3.321 UMOV (General) - * C6.3.237 SMOV (General) + * UMOV (General) + * SMOV (General) * * 31 30 29 21 20 16 15 12 10 9 5 4 0 * +---+---+-------------------+--------+-------------+------+------+ @@ -XXX,XX +XXX,XX @@ static void handle_simd_umov_smov(DisasContext *s, int is_q, int is_signed, } } -/* C3.6.5 AdvSIMD copy +/* AdvSIMD copy * 31 30 29 28 21 20 16 15 14 11 10 9 5 4 0 * +---+---+----+-----------------+------+---+------+---+------+------+ * | 0 | Q | op | 0 1 1 1 0 0 0 0 | imm5 | 0 | imm4 | 1 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_copy(DisasContext *s, uint32_t insn) } } -/* C3.6.6 AdvSIMD modified immediate +/* AdvSIMD modified immediate * 31 30 29 28 19 18 16 15 12 11 10 9 5 4 0 * +---+---+----+---------------------+-----+-------+----+---+-------+------+ * | 0 | Q | op | 0 1 1 1 1 0 0 0 0 0 | abc | cmode | o2 | 1 | defgh | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_mod_imm(DisasContext *s, uint32_t insn) tcg_temp_free_i64(tcg_imm); } -/* C3.6.7 AdvSIMD scalar copy +/* AdvSIMD scalar copy * 31 30 29 28 21 20 16 15 14 11 10 9 5 4 0 * +-----+----+-----------------+------+---+------+---+------+------+ * | 0 1 | op | 1 1 1 1 0 0 0 0 | imm5 | 0 | imm4 | 1 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_scalar_copy(DisasContext *s, uint32_t insn) handle_simd_dupes(s, rd, rn, imm5); } -/* C3.6.8 AdvSIMD scalar pairwise +/* AdvSIMD scalar pairwise * 31 30 29 28 24 23 22 21 17 16 12 11 10 9 5 4 0 * +-----+---+-----------+------+-----------+--------+-----+------+------+ * | 0 1 | U | 1 1 1 1 0 | size | 1 1 0 0 0 | opcode | 1 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_simd_shift_fpint_conv(DisasContext *s, bool is_scalar, tcg_temp_free_i32(tcg_rmode); } -/* C3.6.9 AdvSIMD scalar shift by immediate +/* AdvSIMD scalar shift by immediate * 31 30 29 28 23 22 19 18 16 15 11 10 9 5 4 0 * +-----+---+-------------+------+------+--------+---+------+------+ * | 0 1 | U | 1 1 1 1 1 0 | immh | immb | opcode | 1 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_scalar_shift_imm(DisasContext *s, uint32_t insn) } } -/* C3.6.10 AdvSIMD scalar three different +/* AdvSIMD scalar three different * 31 30 29 28 24 23 22 21 20 16 15 12 11 10 9 5 4 0 * +-----+---+-----------+------+---+------+--------+-----+------+------+ * | 0 1 | U | 1 1 1 1 0 | size | 1 | Rm | opcode | 0 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_3same_float(DisasContext *s, int size, int elements, } } -/* C3.6.11 AdvSIMD scalar three same +/* AdvSIMD scalar three same * 31 30 29 28 24 23 22 21 20 16 15 11 10 9 5 4 0 * +-----+---+-----------+------+---+------+--------+---+------+------+ * | 0 1 | U | 1 1 1 1 0 | size | 1 | Rm | opcode | 1 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_2misc_satacc(DisasContext *s, bool is_scalar, bool is_u, } } -/* C3.6.12 AdvSIMD scalar two reg misc +/* AdvSIMD scalar two reg misc * 31 30 29 28 24 23 22 21 17 16 12 11 10 9 5 4 0 * +-----+---+-----------+------+-----------+--------+-----+------+------+ * | 0 1 | U | 1 1 1 1 0 | size | 1 0 0 0 0 | opcode | 1 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_vec_simd_shrn(DisasContext *s, bool is_q, } -/* C3.6.14 AdvSIMD shift by immediate +/* AdvSIMD shift by immediate * 31 30 29 28 23 22 19 18 16 15 11 10 9 5 4 0 * +---+---+---+-------------+------+------+--------+---+------+------+ * | 0 | Q | U | 0 1 1 1 1 0 | immh | immb | opcode | 1 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_pmull_64(DisasContext *s, int is_q, int rd, int rn, int rm) tcg_temp_free_i64(tcg_res); } -/* C3.6.15 AdvSIMD three different +/* AdvSIMD three different * 31 30 29 28 24 23 22 21 20 16 15 12 11 10 9 5 4 0 * +---+---+---+-----------+------+---+------+--------+-----+------+------+ * | 0 | Q | U | 0 1 1 1 0 | size | 1 | Rm | opcode | 0 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_3same_int(DisasContext *s, uint32_t insn) } } -/* C3.6.16 AdvSIMD three same +/* AdvSIMD three same * 31 30 29 28 24 23 22 21 20 16 15 11 10 9 5 4 0 * +---+---+---+-----------+------+---+------+--------+---+------+------+ * | 0 | Q | U | 0 1 1 1 0 | size | 1 | Rm | opcode | 1 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void handle_shll(DisasContext *s, bool is_q, int size, int rn, int rd) } } -/* C3.6.17 AdvSIMD two reg misc +/* AdvSIMD two reg misc * 31 30 29 28 24 23 22 21 17 16 12 11 10 9 5 4 0 * +---+---+---+-----------+------+-----------+--------+-----+------+------+ * | 0 | Q | U | 0 1 1 1 0 | size | 1 0 0 0 0 | opcode | 1 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_two_reg_misc(DisasContext *s, uint32_t insn) } } -/* C3.6.13 AdvSIMD scalar x indexed element +/* AdvSIMD scalar x indexed element * 31 30 29 28 24 23 22 21 20 19 16 15 12 11 10 9 5 4 0 * +-----+---+-----------+------+---+---+------+-----+---+---+------+------+ * | 0 1 | U | 1 1 1 1 1 | size | L | M | Rm | opc | H | 0 | Rn | Rd | * +-----+---+-----------+------+---+---+------+-----+---+---+------+------+ - * C3.6.18 AdvSIMD vector x indexed element + * AdvSIMD vector x indexed element * 31 30 29 28 24 23 22 21 20 19 16 15 12 11 10 9 5 4 0 * +---+---+---+-----------+------+---+---+------+-----+---+---+------+------+ * | 0 | Q | U | 0 1 1 1 1 | size | L | M | Rm | opc | H | 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_simd_indexed(DisasContext *s, uint32_t insn) } } -/* C3.6.19 Crypto AES +/* Crypto AES * 31 24 23 22 21 17 16 12 11 10 9 5 4 0 * +-----------------+------+-----------+--------+-----+------+------+ * | 0 1 0 0 1 1 1 0 | size | 1 0 1 0 0 | opcode | 1 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_crypto_aes(DisasContext *s, uint32_t insn) tcg_temp_free_i32(tcg_decrypt); } -/* C3.6.20 Crypto three-reg SHA +/* Crypto three-reg SHA * 31 24 23 22 21 20 16 15 14 12 11 10 9 5 4 0 * +-----------------+------+---+------+---+--------+-----+------+------+ * | 0 1 0 1 1 1 1 0 | size | 0 | Rm | 0 | opcode | 0 0 | Rn | Rd | @@ -XXX,XX +XXX,XX @@ static void disas_crypto_three_reg_sha(DisasContext *s, uint32_t insn) tcg_temp_free_i32(tcg_rm_regno); } -/* C3.6.21 Crypto two-reg SHA +/* Crypto two-reg SHA * 31 24 23 22 21 17 16 12 11 10 9 5 4 0 * +-----------------+------+-----------+--------+-----+------+------+ * | 0 1 0 1 1 1 1 0 | size | 1 0 1 0 0 | opcode | 1 0 | Rn | Rd | -- 2.7.4 Update the static_ops functions to use new-style mmio rather than the legacy old_mmio functions. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505580378-9044-2-git-send-email-peter.maydell@linaro.org --- hw/arm/palm.c | 30 ++++++++++-------------------- 1 file changed, 10 insertions(+), 20 deletions(-) diff --git a/hw/arm/palm.c b/hw/arm/palm.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/palm.c +++ b/hw/arm/palm.c @@ -XXX,XX +XXX,XX @@ #include "exec/address-spaces.h" #include "cpu.h" -static uint32_t static_readb(void *opaque, hwaddr offset) +static uint64_t static_read(void *opaque, hwaddr offset, unsigned size) { - uint32_t *val = (uint32_t *) opaque; - return *val >> ((offset & 3) << 3); -} + uint32_t *val = (uint32_t *)opaque; + uint32_t sizemask = 7 >> size; -static uint32_t static_readh(void *opaque, hwaddr offset) -{ - uint32_t *val = (uint32_t *) opaque; - return *val >> ((offset & 1) << 3); -} - -static uint32_t static_readw(void *opaque, hwaddr offset) -{ - uint32_t *val = (uint32_t *) opaque; - return *val >> ((offset & 0) << 3); + return *val >> ((offset & sizemask) << 3); } -static void static_write(void *opaque, hwaddr offset, - uint32_t value) +static void static_write(void *opaque, hwaddr offset, uint64_t value, + unsigned size) { #ifdef SPY printf("%s: value %08lx written at " PA_FMT "\n", @@ -XXX,XX +XXX,XX @@ static void static_write(void *opaque, hwaddr offset, } static const MemoryRegionOps static_ops = { - .old_mmio = { - .read = { static_readb, static_readh, static_readw, }, - .write = { static_write, static_write, static_write, }, - }, + .read = static_read, + .write = static_write, + .valid.min_access_size = 1, + .valid.max_access_size = 4, .endianness = DEVICE_NATIVE_ENDIAN, }; -- 2.7.4 Drop the use of old_mmio in the omap2_gpio memory ops. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505580378-9044-3-git-send-email-peter.maydell@linaro.org --- hw/gpio/omap_gpio.c | 26 ++++++++++++-------------- 1 file changed, 12 insertions(+), 14 deletions(-) diff --git a/hw/gpio/omap_gpio.c b/hw/gpio/omap_gpio.c index XXXXXXX..XXXXXXX 100644 --- a/hw/gpio/omap_gpio.c +++ b/hw/gpio/omap_gpio.c @@ -XXX,XX +XXX,XX @@ static void omap2_gpio_module_write(void *opaque, hwaddr addr, } } -static uint32_t omap2_gpio_module_readp(void *opaque, hwaddr addr) +static uint64_t omap2_gpio_module_readp(void *opaque, hwaddr addr, + unsigned size) { return omap2_gpio_module_read(opaque, addr & ~3) >> ((addr & 3) << 3); } static void omap2_gpio_module_writep(void *opaque, hwaddr addr, - uint32_t value) + uint64_t value, unsigned size) { uint32_t cur = 0; uint32_t mask = 0xffff; + if (size == 4) { + omap2_gpio_module_write(opaque, addr, value); + return; + } + switch (addr & ~3) { case 0x00: /* GPIO_REVISION */ case 0x14: /* GPIO_SYSSTATUS */ @@ -XXX,XX +XXX,XX @@ static void omap2_gpio_module_writep(void *opaque, hwaddr addr, } static const MemoryRegionOps omap2_gpio_module_ops = { - .old_mmio = { - .read = { - omap2_gpio_module_readp, - omap2_gpio_module_readp, - omap2_gpio_module_read, - }, - .write = { - omap2_gpio_module_writep, - omap2_gpio_module_writep, - omap2_gpio_module_write, - }, - }, + .read = omap2_gpio_module_readp, + .write = omap2_gpio_module_writep, + .valid.min_access_size = 1, + .valid.max_access_size = 4, .endianness = DEVICE_NATIVE_ENDIAN, }; -- 2.7.4 Don't use the old_mmio in the memory region ops struct. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505580378-9044-4-git-send-email-peter.maydell@linaro.org --- hw/timer/omap_synctimer.c | 35 +++++++++++++++++++++-------------- 1 file changed, 21 insertions(+), 14 deletions(-) diff --git a/hw/timer/omap_synctimer.c b/hw/timer/omap_synctimer.c index XXXXXXX..XXXXXXX 100644 --- a/hw/timer/omap_synctimer.c +++ b/hw/timer/omap_synctimer.c @@ -XXX,XX +XXX,XX @@ static uint32_t omap_synctimer_readh(void *opaque, hwaddr addr) } } -static void omap_synctimer_write(void *opaque, hwaddr addr, - uint32_t value) +static uint64_t omap_synctimer_readfn(void *opaque, hwaddr addr, + unsigned size) +{ + switch (size) { + case 1: + return omap_badwidth_read32(opaque, addr); + case 2: + return omap_synctimer_readh(opaque, addr); + case 4: + return omap_synctimer_readw(opaque, addr); + default: + g_assert_not_reached(); + } +} + +static void omap_synctimer_writefn(void *opaque, hwaddr addr, + uint64_t value, unsigned size) { OMAP_BAD_REG(addr); } static const MemoryRegionOps omap_synctimer_ops = { - .old_mmio = { - .read = { - omap_badwidth_read32, - omap_synctimer_readh, - omap_synctimer_readw, - }, - .write = { - omap_badwidth_write32, - omap_synctimer_write, - omap_synctimer_write, - }, - }, + .read = omap_synctimer_readfn, + .write = omap_synctimer_writefn, + .valid.min_access_size = 1, + .valid.max_access_size = 4, .endianness = DEVICE_NATIVE_ENDIAN, }; -- 2.7.4 Don't use the old_mmio struct in memory region ops. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505580378-9044-5-git-send-email-peter.maydell@linaro.org --- hw/timer/omap_gptimer.c | 49 +++++++++++++++++++++++++++++++++++++------------ 1 file changed, 37 insertions(+), 12 deletions(-) diff --git a/hw/timer/omap_gptimer.c b/hw/timer/omap_gptimer.c index XXXXXXX..XXXXXXX 100644 --- a/hw/timer/omap_gptimer.c +++ b/hw/timer/omap_gptimer.c @@ -XXX,XX +XXX,XX @@ static void omap_gp_timer_writeh(void *opaque, hwaddr addr, s->writeh = (uint16_t) value; } +static uint64_t omap_gp_timer_readfn(void *opaque, hwaddr addr, + unsigned size) +{ + switch (size) { + case 1: + return omap_badwidth_read32(opaque, addr); + case 2: + return omap_gp_timer_readh(opaque, addr); + case 4: + return omap_gp_timer_readw(opaque, addr); + default: + g_assert_not_reached(); + } +} + +static void omap_gp_timer_writefn(void *opaque, hwaddr addr, + uint64_t value, unsigned size) +{ + switch (size) { + case 1: + omap_badwidth_write32(opaque, addr, value); + break; + case 2: + omap_gp_timer_writeh(opaque, addr, value); + break; + case 4: + omap_gp_timer_write(opaque, addr, value); + break; + default: + g_assert_not_reached(); + } +} + static const MemoryRegionOps omap_gp_timer_ops = { - .old_mmio = { - .read = { - omap_badwidth_read32, - omap_gp_timer_readh, - omap_gp_timer_readw, - }, - .write = { - omap_badwidth_write32, - omap_gp_timer_writeh, - omap_gp_timer_write, - }, - }, + .read = omap_gp_timer_readfn, + .write = omap_gp_timer_writefn, + .valid.min_access_size = 1, + .valid.max_access_size = 4, .endianness = DEVICE_NATIVE_ENDIAN, }; -- 2.7.4 Don't use old_mmio in the memory region ops struct. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505580378-9044-6-git-send-email-peter.maydell@linaro.org --- hw/i2c/omap_i2c.c | 44 ++++++++++++++++++++++++++++++++------------ 1 file changed, 32 insertions(+), 12 deletions(-) diff --git a/hw/i2c/omap_i2c.c b/hw/i2c/omap_i2c.c index XXXXXXX..XXXXXXX 100644 --- a/hw/i2c/omap_i2c.c +++ b/hw/i2c/omap_i2c.c @@ -XXX,XX +XXX,XX @@ static void omap_i2c_writeb(void *opaque, hwaddr addr, } } +static uint64_t omap_i2c_readfn(void *opaque, hwaddr addr, + unsigned size) +{ + switch (size) { + case 2: + return omap_i2c_read(opaque, addr); + default: + return omap_badwidth_read16(opaque, addr); + } +} + +static void omap_i2c_writefn(void *opaque, hwaddr addr, + uint64_t value, unsigned size) +{ + switch (size) { + case 1: + /* Only the last fifo write can be 8 bit. */ + omap_i2c_writeb(opaque, addr, value); + break; + case 2: + omap_i2c_write(opaque, addr, value); + break; + default: + omap_badwidth_write16(opaque, addr, value); + break; + } +} + static const MemoryRegionOps omap_i2c_ops = { - .old_mmio = { - .read = { - omap_badwidth_read16, - omap_i2c_read, - omap_badwidth_read16, - }, - .write = { - omap_i2c_writeb, /* Only the last fifo write can be 8 bit. */ - omap_i2c_write, - omap_badwidth_write16, - }, - }, + .read = omap_i2c_readfn, + .write = omap_i2c_writefn, + .valid.min_access_size = 1, + .valid.max_access_size = 4, .endianness = DEVICE_NATIVE_ENDIAN, }; -- 2.7.4 Don't use old_mmio in the memory region ops struct. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 1505580378-9044-7-git-send-email-peter.maydell@linaro.org --- hw/arm/omap2.c | 49 +++++++++++++++++++++++++++++++++++++------------ 1 file changed, 37 insertions(+), 12 deletions(-) diff --git a/hw/arm/omap2.c b/hw/arm/omap2.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/omap2.c +++ b/hw/arm/omap2.c @@ -XXX,XX +XXX,XX @@ static void omap_sysctl_write(void *opaque, hwaddr addr, } } +static uint64_t omap_sysctl_readfn(void *opaque, hwaddr addr, + unsigned size) +{ + switch (size) { + case 1: + return omap_sysctl_read8(opaque, addr); + case 2: + return omap_badwidth_read32(opaque, addr); /* TODO */ + case 4: + return omap_sysctl_read(opaque, addr); + default: + g_assert_not_reached(); + } +} + +static void omap_sysctl_writefn(void *opaque, hwaddr addr, + uint64_t value, unsigned size) +{ + switch (size) { + case 1: + omap_sysctl_write8(opaque, addr, value); + break; + case 2: + omap_badwidth_write32(opaque, addr, value); /* TODO */ + break; + case 4: + omap_sysctl_write(opaque, addr, value); + break; + default: + g_assert_not_reached(); + } +} + static const MemoryRegionOps omap_sysctl_ops = { - .old_mmio = { - .read = { - omap_sysctl_read8, - omap_badwidth_read32, /* TODO */ - omap_sysctl_read, - }, - .write = { - omap_sysctl_write8, - omap_badwidth_write32, /* TODO */ - omap_sysctl_write, - }, - }, + .read = omap_sysctl_readfn, + .write = omap_sysctl_writefn, + .valid.min_access_size = 1, + .valid.max_access_size = 4, .endianness = DEVICE_NATIVE_ENDIAN, }; -- 2.7.4 From: Subbaraya Sundeep <sundeep.lkml@gmail.com> Modelled System Timer in Microsemi's Smartfusion2 Soc. Timer has two 32bit down counters and two interrupts. Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 20170920201737.25723-2-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- hw/timer/Makefile.objs | 1 + include/hw/timer/mss-timer.h | 64 ++++++++++ hw/timer/mss-timer.c | 289 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 354 insertions(+) create mode 100644 include/hw/timer/mss-timer.h create mode 100644 hw/timer/mss-timer.c diff --git a/hw/timer/Makefile.objs b/hw/timer/Makefile.objs index XXXXXXX..XXXXXXX 100644 --- a/hw/timer/Makefile.objs +++ b/hw/timer/Makefile.objs @@ -XXX,XX +XXX,XX @@ common-obj-$(CONFIG_ASPEED_SOC) += aspeed_timer.o common-obj-$(CONFIG_SUN4V_RTC) += sun4v-rtc.o common-obj-$(CONFIG_CMSDK_APB_TIMER) += cmsdk-apb-timer.o +common-obj-$(CONFIG_MSF2) += mss-timer.o diff --git a/include/hw/timer/mss-timer.h b/include/hw/timer/mss-timer.h new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/include/hw/timer/mss-timer.h @@ -XXX,XX +XXX,XX @@ +/* + * Microsemi SmartFusion2 Timer. + * + * Copyright (c) 2017 Subbaraya Sundeep <sundeep.lkml@gmail.com> + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#ifndef HW_MSS_TIMER_H +#define HW_MSS_TIMER_H + +#include "hw/sysbus.h" +#include "hw/ptimer.h" + +#define TYPE_MSS_TIMER "mss-timer" +#define MSS_TIMER(obj) OBJECT_CHECK(MSSTimerState, \ + (obj), TYPE_MSS_TIMER) + +/* + * There are two 32-bit down counting timers. + * Timers 1 and 2 can be concatenated into a single 64-bit Timer + * that operates either in Periodic mode or in One-shot mode. + * Writing 1 to the TIM64_MODE register bit 0 sets the Timers in 64-bit mode. + * In 64-bit mode, writing to the 32-bit registers has no effect. + * Similarly, in 32-bit mode, writing to the 64-bit mode registers + * has no effect. Only two 32-bit timers are supported currently. + */ +#define NUM_TIMERS 2 + +#define R_TIM1_MAX 6 + +struct Msf2Timer { + QEMUBH *bh; + ptimer_state *ptimer; + + uint32_t regs[R_TIM1_MAX]; + qemu_irq irq; +}; + +typedef struct MSSTimerState { + SysBusDevice parent_obj; + + MemoryRegion mmio; + uint32_t freq_hz; + struct Msf2Timer timers[NUM_TIMERS]; +} MSSTimerState; + +#endif /* HW_MSS_TIMER_H */ diff --git a/hw/timer/mss-timer.c b/hw/timer/mss-timer.c new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/hw/timer/mss-timer.c @@ -XXX,XX +XXX,XX @@ +/* + * Block model of System timer present in + * Microsemi's SmartFusion2 and SmartFusion SoCs. + * + * Copyright (c) 2017 Subbaraya Sundeep <sundeep.lkml@gmail.com>. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#include "qemu/osdep.h" +#include "qemu/main-loop.h" +#include "qemu/log.h" +#include "hw/timer/mss-timer.h" + +#ifndef MSS_TIMER_ERR_DEBUG +#define MSS_TIMER_ERR_DEBUG 0 +#endif + +#define DB_PRINT_L(lvl, fmt, args...) do { \ + if (MSS_TIMER_ERR_DEBUG >= lvl) { \ + qemu_log("%s: " fmt "\n", __func__, ## args); \ + } \ +} while (0); + +#define DB_PRINT(fmt, args...) DB_PRINT_L(1, fmt, ## args) + +#define R_TIM_VAL 0 +#define R_TIM_LOADVAL 1 +#define R_TIM_BGLOADVAL 2 +#define R_TIM_CTRL 3 +#define R_TIM_RIS 4 +#define R_TIM_MIS 5 + +#define TIMER_CTRL_ENBL (1 << 0) +#define TIMER_CTRL_ONESHOT (1 << 1) +#define TIMER_CTRL_INTR (1 << 2) +#define TIMER_RIS_ACK (1 << 0) +#define TIMER_RST_CLR (1 << 6) +#define TIMER_MODE (1 << 0) + +static void timer_update_irq(struct Msf2Timer *st) +{ + bool isr, ier; + + isr = !!(st->regs[R_TIM_RIS] & TIMER_RIS_ACK); + ier = !!(st->regs[R_TIM_CTRL] & TIMER_CTRL_INTR); + qemu_set_irq(st->irq, (ier && isr)); +} + +static void timer_update(struct Msf2Timer *st) +{ + uint64_t count; + + if (!(st->regs[R_TIM_CTRL] & TIMER_CTRL_ENBL)) { + ptimer_stop(st->ptimer); + return; + } + + count = st->regs[R_TIM_LOADVAL]; + ptimer_set_limit(st->ptimer, count, 1); + ptimer_run(st->ptimer, 1); +} + +static uint64_t +timer_read(void *opaque, hwaddr offset, unsigned int size) +{ + MSSTimerState *t = opaque; + hwaddr addr; + struct Msf2Timer *st; + uint32_t ret = 0; + int timer = 0; + int isr; + int ier; + + addr = offset >> 2; + /* + * Two independent timers has same base address. + * Based on address passed figure out which timer is being used. + */ + if ((addr >= R_TIM1_MAX) && (addr < NUM_TIMERS * R_TIM1_MAX)) { + timer = 1; + addr -= R_TIM1_MAX; + } + + st = &t->timers[timer]; + + switch (addr) { + case R_TIM_VAL: + ret = ptimer_get_count(st->ptimer); + break; + + case R_TIM_MIS: + isr = !!(st->regs[R_TIM_RIS] & TIMER_RIS_ACK); + ier = !!(st->regs[R_TIM_CTRL] & TIMER_CTRL_INTR); + ret = ier & isr; + break; + + default: + if (addr < R_TIM1_MAX) { + ret = st->regs[addr]; + } else { + qemu_log_mask(LOG_GUEST_ERROR, + TYPE_MSS_TIMER": 64-bit mode not supported\n"); + return ret; + } + break; + } + + DB_PRINT("timer=%d 0x%" HWADDR_PRIx "=0x%" PRIx32, timer, offset, + ret); + return ret; +} + +static void +timer_write(void *opaque, hwaddr offset, + uint64_t val64, unsigned int size) +{ + MSSTimerState *t = opaque; + hwaddr addr; + struct Msf2Timer *st; + int timer = 0; + uint32_t value = val64; + + addr = offset >> 2; + /* + * Two independent timers has same base address. + * Based on addr passed figure out which timer is being used. + */ + if ((addr >= R_TIM1_MAX) && (addr < NUM_TIMERS * R_TIM1_MAX)) { + timer = 1; + addr -= R_TIM1_MAX; + } + + st = &t->timers[timer]; + + DB_PRINT("addr=0x%" HWADDR_PRIx " val=0x%" PRIx32 " (timer=%d)", offset, + value, timer); + + switch (addr) { + case R_TIM_CTRL: + st->regs[R_TIM_CTRL] = value; + timer_update(st); + break; + + case R_TIM_RIS: + if (value & TIMER_RIS_ACK) { + st->regs[R_TIM_RIS] &= ~TIMER_RIS_ACK; + } + break; + + case R_TIM_LOADVAL: + st->regs[R_TIM_LOADVAL] = value; + if (st->regs[R_TIM_CTRL] & TIMER_CTRL_ENBL) { + timer_update(st); + } + break; + + case R_TIM_BGLOADVAL: + st->regs[R_TIM_BGLOADVAL] = value; + st->regs[R_TIM_LOADVAL] = value; + break; + + case R_TIM_VAL: + case R_TIM_MIS: + break; + + default: + if (addr < R_TIM1_MAX) { + st->regs[addr] = value; + } else { + qemu_log_mask(LOG_GUEST_ERROR, + TYPE_MSS_TIMER": 64-bit mode not supported\n"); + return; + } + break; + } + timer_update_irq(st); +} + +static const MemoryRegionOps timer_ops = { + .read = timer_read, + .write = timer_write, + .endianness = DEVICE_NATIVE_ENDIAN, + .valid = { + .min_access_size = 1, + .max_access_size = 4 + } +}; + +static void timer_hit(void *opaque) +{ + struct Msf2Timer *st = opaque; + + st->regs[R_TIM_RIS] |= TIMER_RIS_ACK; + + if (!(st->regs[R_TIM_CTRL] & TIMER_CTRL_ONESHOT)) { + timer_update(st); + } + timer_update_irq(st); +} + +static void mss_timer_init(Object *obj) +{ + MSSTimerState *t = MSS_TIMER(obj); + int i; + + /* Init all the ptimers. */ + for (i = 0; i < NUM_TIMERS; i++) { + struct Msf2Timer *st = &t->timers[i]; + + st->bh = qemu_bh_new(timer_hit, st); + st->ptimer = ptimer_init(st->bh, PTIMER_POLICY_DEFAULT); + ptimer_set_freq(st->ptimer, t->freq_hz); + sysbus_init_irq(SYS_BUS_DEVICE(obj), &st->irq); + } + + memory_region_init_io(&t->mmio, OBJECT(t), &timer_ops, t, TYPE_MSS_TIMER, + NUM_TIMERS * R_TIM1_MAX * 4); + sysbus_init_mmio(SYS_BUS_DEVICE(obj), &t->mmio); +} + +static const VMStateDescription vmstate_timers = { + .name = "mss-timer-block", + .version_id = 1, + .minimum_version_id = 1, + .fields = (VMStateField[]) { + VMSTATE_PTIMER(ptimer, struct Msf2Timer), + VMSTATE_UINT32_ARRAY(regs, struct Msf2Timer, R_TIM1_MAX), + VMSTATE_END_OF_LIST() + } +}; + +static const VMStateDescription vmstate_mss_timer = { + .name = TYPE_MSS_TIMER, + .version_id = 1, + .minimum_version_id = 1, + .fields = (VMStateField[]) { + VMSTATE_UINT32(freq_hz, MSSTimerState), + VMSTATE_STRUCT_ARRAY(timers, MSSTimerState, NUM_TIMERS, 0, + vmstate_timers, struct Msf2Timer), + VMSTATE_END_OF_LIST() + } +}; + +static Property mss_timer_properties[] = { + /* Libero GUI shows 100Mhz as default for clocks */ + DEFINE_PROP_UINT32("clock-frequency", MSSTimerState, freq_hz, + 100 * 1000000), + DEFINE_PROP_END_OF_LIST(), +}; + +static void mss_timer_class_init(ObjectClass *klass, void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + + dc->props = mss_timer_properties; + dc->vmsd = &vmstate_mss_timer; +} + +static const TypeInfo mss_timer_info = { + .name = TYPE_MSS_TIMER, + .parent = TYPE_SYS_BUS_DEVICE, + .instance_size = sizeof(MSSTimerState), + .instance_init = mss_timer_init, + .class_init = mss_timer_class_init, +}; + +static void mss_timer_register_types(void) +{ + type_register_static(&mss_timer_info); +} + +type_init(mss_timer_register_types) -- 2.7.4 From: Subbaraya Sundeep <sundeep.lkml@gmail.com> Added Sytem register block of Smartfusion2. This block has PLL registers which are accessed by guest. Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 20170920201737.25723-3-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- hw/misc/Makefile.objs | 1 + include/hw/misc/msf2-sysreg.h | 77 ++++++++++++++++++++ hw/misc/msf2-sysreg.c | 160 ++++++++++++++++++++++++++++++++++++++++++ hw/misc/trace-events | 5 ++ 4 files changed, 243 insertions(+) create mode 100644 include/hw/misc/msf2-sysreg.h create mode 100644 hw/misc/msf2-sysreg.c diff --git a/hw/misc/Makefile.objs b/hw/misc/Makefile.objs index XXXXXXX..XXXXXXX 100644 --- a/hw/misc/Makefile.objs +++ b/hw/misc/Makefile.objs @@ -XXX,XX +XXX,XX @@ obj-$(CONFIG_HYPERV_TESTDEV) += hyperv_testdev.o obj-$(CONFIG_AUX) += auxbus.o obj-$(CONFIG_ASPEED_SOC) += aspeed_scu.o aspeed_sdmc.o obj-y += mmio_interface.o +obj-$(CONFIG_MSF2) += msf2-sysreg.o diff --git a/include/hw/misc/msf2-sysreg.h b/include/hw/misc/msf2-sysreg.h new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/include/hw/misc/msf2-sysreg.h @@ -XXX,XX +XXX,XX @@ +/* + * Microsemi SmartFusion2 SYSREG + * + * Copyright (c) 2017 Subbaraya Sundeep <sundeep.lkml@gmail.com> + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#ifndef HW_MSF2_SYSREG_H +#define HW_MSF2_SYSREG_H + +#include "hw/sysbus.h" + +enum { + ESRAM_CR = 0x00 / 4, + ESRAM_MAX_LAT, + DDR_CR, + ENVM_CR, + ENVM_REMAP_BASE_CR, + ENVM_REMAP_FAB_CR, + CC_CR, + CC_REGION_CR, + CC_LOCK_BASE_ADDR_CR, + CC_FLUSH_INDX_CR, + DDRB_BUF_TIMER_CR, + DDRB_NB_ADDR_CR, + DDRB_NB_SIZE_CR, + DDRB_CR, + + SOFT_RESET_CR = 0x48 / 4, + M3_CR, + + GPIO_SYSRESET_SEL_CR = 0x58 / 4, + + MDDR_CR = 0x60 / 4, + + MSSDDR_PLL_STATUS_LOW_CR = 0x90 / 4, + MSSDDR_PLL_STATUS_HIGH_CR, + MSSDDR_FACC1_CR, + MSSDDR_FACC2_CR, + + MSSDDR_PLL_STATUS = 0x150 / 4, +}; + +#define MSF2_SYSREG_MMIO_SIZE 0x300 + +#define TYPE_MSF2_SYSREG "msf2-sysreg" +#define MSF2_SYSREG(obj) OBJECT_CHECK(MSF2SysregState, (obj), TYPE_MSF2_SYSREG) + +typedef struct MSF2SysregState { + SysBusDevice parent_obj; + + MemoryRegion iomem; + + uint8_t apb0div; + uint8_t apb1div; + + uint32_t regs[MSF2_SYSREG_MMIO_SIZE / 4]; +} MSF2SysregState; + +#endif /* HW_MSF2_SYSREG_H */ diff --git a/hw/misc/msf2-sysreg.c b/hw/misc/msf2-sysreg.c new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/hw/misc/msf2-sysreg.c @@ -XXX,XX +XXX,XX @@ +/* + * System Register block model of Microsemi SmartFusion2. + * + * Copyright (c) 2017 Subbaraya Sundeep <sundeep.lkml@gmail.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, see <http://www.gnu.org/licenses/>. + */ + +#include "qemu/osdep.h" +#include "qapi/error.h" +#include "qemu/log.h" +#include "hw/misc/msf2-sysreg.h" +#include "qemu/error-report.h" +#include "trace.h" + +static inline int msf2_divbits(uint32_t div) +{ + int r = ctz32(div); + + return (div < 8) ? r : r + 1; +} + +static void msf2_sysreg_reset(DeviceState *d) +{ + MSF2SysregState *s = MSF2_SYSREG(d); + + s->regs[MSSDDR_PLL_STATUS_LOW_CR] = 0x021A2358; + s->regs[MSSDDR_PLL_STATUS] = 0x3; + s->regs[MSSDDR_FACC1_CR] = msf2_divbits(s->apb0div) << 5 | + msf2_divbits(s->apb1div) << 2; +} + +static uint64_t msf2_sysreg_read(void *opaque, hwaddr offset, + unsigned size) +{ + MSF2SysregState *s = opaque; + uint32_t ret = 0; + + offset >>= 2; + if (offset < ARRAY_SIZE(s->regs)) { + ret = s->regs[offset]; + trace_msf2_sysreg_read(offset << 2, ret); + } else { + qemu_log_mask(LOG_GUEST_ERROR, + "%s: Bad offset 0x%08" HWADDR_PRIx "\n", __func__, + offset << 2); + } + + return ret; +} + +static void msf2_sysreg_write(void *opaque, hwaddr offset, + uint64_t val, unsigned size) +{ + MSF2SysregState *s = opaque; + uint32_t newval = val; + + offset >>= 2; + + switch (offset) { + case MSSDDR_PLL_STATUS: + trace_msf2_sysreg_write_pll_status(); + break; + + case ESRAM_CR: + case DDR_CR: + case ENVM_REMAP_BASE_CR: + if (newval != s->regs[offset]) { + qemu_log_mask(LOG_UNIMP, + TYPE_MSF2_SYSREG": remapping not supported\n"); + } + break; + + default: + if (offset < ARRAY_SIZE(s->regs)) { + trace_msf2_sysreg_write(offset << 2, newval, s->regs[offset]); + s->regs[offset] = newval; + } else { + qemu_log_mask(LOG_GUEST_ERROR, + "%s: Bad offset 0x%08" HWADDR_PRIx "\n", __func__, + offset << 2); + } + break; + } +} + +static const MemoryRegionOps sysreg_ops = { + .read = msf2_sysreg_read, + .write = msf2_sysreg_write, + .endianness = DEVICE_NATIVE_ENDIAN, +}; + +static void msf2_sysreg_init(Object *obj) +{ + MSF2SysregState *s = MSF2_SYSREG(obj); + + memory_region_init_io(&s->iomem, obj, &sysreg_ops, s, TYPE_MSF2_SYSREG, + MSF2_SYSREG_MMIO_SIZE); + sysbus_init_mmio(SYS_BUS_DEVICE(obj), &s->iomem); +} + +static const VMStateDescription vmstate_msf2_sysreg = { + .name = TYPE_MSF2_SYSREG, + .version_id = 1, + .minimum_version_id = 1, + .fields = (VMStateField[]) { + VMSTATE_UINT32_ARRAY(regs, MSF2SysregState, MSF2_SYSREG_MMIO_SIZE / 4), + VMSTATE_END_OF_LIST() + } +}; + +static Property msf2_sysreg_properties[] = { + /* default divisors in Libero GUI */ + DEFINE_PROP_UINT8("apb0divisor", MSF2SysregState, apb0div, 2), + DEFINE_PROP_UINT8("apb1divisor", MSF2SysregState, apb1div, 2), + DEFINE_PROP_END_OF_LIST(), +}; + +static void msf2_sysreg_realize(DeviceState *dev, Error **errp) +{ + MSF2SysregState *s = MSF2_SYSREG(dev); + + if ((s->apb0div > 32 || !is_power_of_2(s->apb0div)) + || (s->apb1div > 32 || !is_power_of_2(s->apb1div))) { + error_setg(errp, "Invalid apb divisor value"); + error_append_hint(errp, "apb divisor must be a power of 2" + " and maximum value is 32\n"); + } +} + +static void msf2_sysreg_class_init(ObjectClass *klass, void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + + dc->vmsd = &vmstate_msf2_sysreg; + dc->reset = msf2_sysreg_reset; + dc->props = msf2_sysreg_properties; + dc->realize = msf2_sysreg_realize; +} + +static const TypeInfo msf2_sysreg_info = { + .name = TYPE_MSF2_SYSREG, + .parent = TYPE_SYS_BUS_DEVICE, + .class_init = msf2_sysreg_class_init, + .instance_size = sizeof(MSF2SysregState), + .instance_init = msf2_sysreg_init, +}; + +static void msf2_sysreg_register_types(void) +{ + type_register_static(&msf2_sysreg_info); +} + +type_init(msf2_sysreg_register_types) diff --git a/hw/misc/trace-events b/hw/misc/trace-events index XXXXXXX..XXXXXXX 100644 --- a/hw/misc/trace-events +++ b/hw/misc/trace-events @@ -XXX,XX +XXX,XX @@ mps2_scc_reset(void) "MPS2 SCC: reset" mps2_scc_leds(char led7, char led6, char led5, char led4, char led3, char led2, char led1, char led0) "MPS2 SCC LEDs: %c%c%c%c%c%c%c%c" mps2_scc_cfg_write(unsigned function, unsigned device, uint32_t value) "MPS2 SCC config write: function %d device %d data 0x%" PRIx32 mps2_scc_cfg_read(unsigned function, unsigned device, uint32_t value) "MPS2 SCC config read: function %d device %d data 0x%" PRIx32 + +# hw/misc/msf2-sysreg.c +msf2_sysreg_write(uint64_t offset, uint32_t val, uint32_t prev) "msf2-sysreg write: addr 0x%08" HWADDR_PRIx " data 0x%" PRIx32 " prev 0x%" PRIx32 +msf2_sysreg_read(uint64_t offset, uint32_t val) "msf2-sysreg read: addr 0x%08" HWADDR_PRIx " data 0x%08" PRIx32 +msf2_sysreg_write_pll_status(void) "Invalid write to read only PLL status register" -- 2.7.4 From: Subbaraya Sundeep <sundeep.lkml@gmail.com> Modelled Microsemi's Smartfusion2 SPI controller. Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 20170920201737.25723-4-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- hw/ssi/Makefile.objs | 1 + include/hw/ssi/mss-spi.h | 58 +++++++ hw/ssi/mss-spi.c | 404 +++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 463 insertions(+) create mode 100644 include/hw/ssi/mss-spi.h create mode 100644 hw/ssi/mss-spi.c diff --git a/hw/ssi/Makefile.objs b/hw/ssi/Makefile.objs index XXXXXXX..XXXXXXX 100644 --- a/hw/ssi/Makefile.objs +++ b/hw/ssi/Makefile.objs @@ -XXX,XX +XXX,XX @@ common-obj-$(CONFIG_XILINX_SPI) += xilinx_spi.o common-obj-$(CONFIG_XILINX_SPIPS) += xilinx_spips.o common-obj-$(CONFIG_ASPEED_SOC) += aspeed_smc.o common-obj-$(CONFIG_STM32F2XX_SPI) += stm32f2xx_spi.o +common-obj-$(CONFIG_MSF2) += mss-spi.o obj-$(CONFIG_OMAP) += omap_spi.o obj-$(CONFIG_IMX) += imx_spi.o diff --git a/include/hw/ssi/mss-spi.h b/include/hw/ssi/mss-spi.h new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/include/hw/ssi/mss-spi.h @@ -XXX,XX +XXX,XX @@ +/* + * Microsemi SmartFusion2 SPI + * + * Copyright (c) 2017 Subbaraya Sundeep <sundeep.lkml@gmail.com> + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#ifndef HW_MSS_SPI_H +#define HW_MSS_SPI_H + +#include "hw/sysbus.h" +#include "hw/ssi/ssi.h" +#include "qemu/fifo32.h" + +#define TYPE_MSS_SPI "mss-spi" +#define MSS_SPI(obj) OBJECT_CHECK(MSSSpiState, (obj), TYPE_MSS_SPI) + +#define R_SPI_MAX 16 + +typedef struct MSSSpiState { + SysBusDevice parent_obj; + + MemoryRegion mmio; + + qemu_irq irq; + + qemu_irq cs_line; + + SSIBus *spi; + + Fifo32 rx_fifo; + Fifo32 tx_fifo; + + int fifo_depth; + uint32_t frame_count; + bool enabled; + + uint32_t regs[R_SPI_MAX]; +} MSSSpiState; + +#endif /* HW_MSS_SPI_H */ diff --git a/hw/ssi/mss-spi.c b/hw/ssi/mss-spi.c new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/hw/ssi/mss-spi.c @@ -XXX,XX +XXX,XX @@ +/* + * Block model of SPI controller present in + * Microsemi's SmartFusion2 and SmartFusion SoCs. + * + * Copyright (C) 2017 Subbaraya Sundeep <sundeep.lkml@gmail.com> + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#include "qemu/osdep.h" +#include "hw/ssi/mss-spi.h" +#include "qemu/log.h" + +#ifndef MSS_SPI_ERR_DEBUG +#define MSS_SPI_ERR_DEBUG 0 +#endif + +#define DB_PRINT_L(lvl, fmt, args...) do { \ + if (MSS_SPI_ERR_DEBUG >= lvl) { \ + qemu_log("%s: " fmt "\n", __func__, ## args); \ + } \ +} while (0); + +#define DB_PRINT(fmt, args...) DB_PRINT_L(1, fmt, ## args) + +#define FIFO_CAPACITY 32 + +#define R_SPI_CONTROL 0 +#define R_SPI_DFSIZE 1 +#define R_SPI_STATUS 2 +#define R_SPI_INTCLR 3 +#define R_SPI_RX 4 +#define R_SPI_TX 5 +#define R_SPI_CLKGEN 6 +#define R_SPI_SS 7 +#define R_SPI_MIS 8 +#define R_SPI_RIS 9 + +#define S_TXDONE (1 << 0) +#define S_RXRDY (1 << 1) +#define S_RXCHOVRF (1 << 2) +#define S_RXFIFOFUL (1 << 4) +#define S_RXFIFOFULNXT (1 << 5) +#define S_RXFIFOEMP (1 << 6) +#define S_RXFIFOEMPNXT (1 << 7) +#define S_TXFIFOFUL (1 << 8) +#define S_TXFIFOFULNXT (1 << 9) +#define S_TXFIFOEMP (1 << 10) +#define S_TXFIFOEMPNXT (1 << 11) +#define S_FRAMESTART (1 << 12) +#define S_SSEL (1 << 13) +#define S_ACTIVE (1 << 14) + +#define C_ENABLE (1 << 0) +#define C_MODE (1 << 1) +#define C_INTRXDATA (1 << 4) +#define C_INTTXDATA (1 << 5) +#define C_INTRXOVRFLO (1 << 6) +#define C_SPS (1 << 26) +#define C_BIGFIFO (1 << 29) +#define C_RESET (1 << 31) + +#define FRAMESZ_MASK 0x1F +#define FMCOUNT_MASK 0x00FFFF00 +#define FMCOUNT_SHIFT 8 + +static void txfifo_reset(MSSSpiState *s) +{ + fifo32_reset(&s->tx_fifo); + + s->regs[R_SPI_STATUS] &= ~S_TXFIFOFUL; + s->regs[R_SPI_STATUS] |= S_TXFIFOEMP; +} + +static void rxfifo_reset(MSSSpiState *s) +{ + fifo32_reset(&s->rx_fifo); + + s->regs[R_SPI_STATUS] &= ~S_RXFIFOFUL; + s->regs[R_SPI_STATUS] |= S_RXFIFOEMP; +} + +static void set_fifodepth(MSSSpiState *s) +{ + unsigned int size = s->regs[R_SPI_DFSIZE] & FRAMESZ_MASK; + + if (size <= 8) { + s->fifo_depth = 32; + } else if (size <= 16) { + s->fifo_depth = 16; + } else if (size <= 32) { + s->fifo_depth = 8; + } else { + s->fifo_depth = 4; + } +} + +static void update_mis(MSSSpiState *s) +{ + uint32_t reg = s->regs[R_SPI_CONTROL]; + uint32_t tmp; + + /* + * form the Control register interrupt enable bits + * same as RIS, MIS and Interrupt clear registers for simplicity + */ + tmp = ((reg & C_INTRXOVRFLO) >> 4) | ((reg & C_INTRXDATA) >> 3) | + ((reg & C_INTTXDATA) >> 5); + s->regs[R_SPI_MIS] |= tmp & s->regs[R_SPI_RIS]; +} + +static void spi_update_irq(MSSSpiState *s) +{ + int irq; + + update_mis(s); + irq = !!(s->regs[R_SPI_MIS]); + + qemu_set_irq(s->irq, irq); +} + +static void mss_spi_reset(DeviceState *d) +{ + MSSSpiState *s = MSS_SPI(d); + + memset(s->regs, 0, sizeof s->regs); + s->regs[R_SPI_CONTROL] = 0x80000102; + s->regs[R_SPI_DFSIZE] = 0x4; + s->regs[R_SPI_STATUS] = S_SSEL | S_TXFIFOEMP | S_RXFIFOEMP; + s->regs[R_SPI_CLKGEN] = 0x7; + s->regs[R_SPI_RIS] = 0x0; + + s->fifo_depth = 4; + s->frame_count = 1; + s->enabled = false; + + rxfifo_reset(s); + txfifo_reset(s); +} + +static uint64_t +spi_read(void *opaque, hwaddr addr, unsigned int size) +{ + MSSSpiState *s = opaque; + uint32_t ret = 0; + + addr >>= 2; + switch (addr) { + case R_SPI_RX: + s->regs[R_SPI_STATUS] &= ~S_RXFIFOFUL; + s->regs[R_SPI_STATUS] &= ~S_RXCHOVRF; + ret = fifo32_pop(&s->rx_fifo); + if (fifo32_is_empty(&s->rx_fifo)) { + s->regs[R_SPI_STATUS] |= S_RXFIFOEMP; + } + break; + + case R_SPI_MIS: + update_mis(s); + ret = s->regs[R_SPI_MIS]; + break; + + default: + if (addr < ARRAY_SIZE(s->regs)) { + ret = s->regs[addr]; + } else { + qemu_log_mask(LOG_GUEST_ERROR, + "%s: Bad offset 0x%" HWADDR_PRIx "\n", __func__, + addr * 4); + return ret; + } + break; + } + + DB_PRINT("addr=0x%" HWADDR_PRIx " = 0x%" PRIx32, addr * 4, ret); + spi_update_irq(s); + return ret; +} + +static void assert_cs(MSSSpiState *s) +{ + qemu_set_irq(s->cs_line, 0); +} + +static void deassert_cs(MSSSpiState *s) +{ + qemu_set_irq(s->cs_line, 1); +} + +static void spi_flush_txfifo(MSSSpiState *s) +{ + uint32_t tx; + uint32_t rx; + bool sps = !!(s->regs[R_SPI_CONTROL] & C_SPS); + + /* + * Chip Select(CS) is automatically controlled by this controller. + * If SPS bit is set in Control register then CS is asserted + * until all the frames set in frame count of Control register are + * transferred. If SPS is not set then CS pulses between frames. + * Note that Slave Select register specifies which of the CS line + * has to be controlled automatically by controller. Bits SS[7:1] are for + * masters in FPGA fabric since we model only Microcontroller subsystem + * of Smartfusion2 we control only one CS(SS[0]) line. + */ + while (!fifo32_is_empty(&s->tx_fifo) && s->frame_count) { + assert_cs(s); + + s->regs[R_SPI_STATUS] &= ~(S_TXDONE | S_RXRDY); + + tx = fifo32_pop(&s->tx_fifo); + DB_PRINT("data tx:0x%" PRIx32, tx); + rx = ssi_transfer(s->spi, tx); + DB_PRINT("data rx:0x%" PRIx32, rx); + + if (fifo32_num_used(&s->rx_fifo) == s->fifo_depth) { + s->regs[R_SPI_STATUS] |= S_RXCHOVRF; + s->regs[R_SPI_RIS] |= S_RXCHOVRF; + } else { + fifo32_push(&s->rx_fifo, rx); + s->regs[R_SPI_STATUS] &= ~S_RXFIFOEMP; + if (fifo32_num_used(&s->rx_fifo) == (s->fifo_depth - 1)) { + s->regs[R_SPI_STATUS] |= S_RXFIFOFULNXT; + } else if (fifo32_num_used(&s->rx_fifo) == s->fifo_depth) { + s->regs[R_SPI_STATUS] |= S_RXFIFOFUL; + } + } + s->frame_count--; + if (!sps) { + deassert_cs(s); + } + } + + if (!s->frame_count) { + s->frame_count = (s->regs[R_SPI_CONTROL] & FMCOUNT_MASK) >> + FMCOUNT_SHIFT; + deassert_cs(s); + s->regs[R_SPI_RIS] |= S_TXDONE | S_RXRDY; + s->regs[R_SPI_STATUS] |= S_TXDONE | S_RXRDY; + } +} + +static void spi_write(void *opaque, hwaddr addr, + uint64_t val64, unsigned int size) +{ + MSSSpiState *s = opaque; + uint32_t value = val64; + + DB_PRINT("addr=0x%" HWADDR_PRIx " =0x%" PRIx32, addr, value); + addr >>= 2; + + switch (addr) { + case R_SPI_TX: + /* adding to already full FIFO */ + if (fifo32_num_used(&s->tx_fifo) == s->fifo_depth) { + break; + } + s->regs[R_SPI_STATUS] &= ~S_TXFIFOEMP; + fifo32_push(&s->tx_fifo, value); + if (fifo32_num_used(&s->tx_fifo) == (s->fifo_depth - 1)) { + s->regs[R_SPI_STATUS] |= S_TXFIFOFULNXT; + } else if (fifo32_num_used(&s->tx_fifo) == s->fifo_depth) { + s->regs[R_SPI_STATUS] |= S_TXFIFOFUL; + } + if (s->enabled) { + spi_flush_txfifo(s); + } + break; + + case R_SPI_CONTROL: + s->regs[R_SPI_CONTROL] = value; + if (value & C_BIGFIFO) { + set_fifodepth(s); + } else { + s->fifo_depth = 4; + } + s->enabled = value & C_ENABLE; + s->frame_count = (value & FMCOUNT_MASK) >> FMCOUNT_SHIFT; + if (value & C_RESET) { + mss_spi_reset(DEVICE(s)); + } + break; + + case R_SPI_DFSIZE: + if (s->enabled) { + break; + } + s->regs[R_SPI_DFSIZE] = value; + break; + + case R_SPI_INTCLR: + s->regs[R_SPI_INTCLR] = value; + if (value & S_TXDONE) { + s->regs[R_SPI_RIS] &= ~S_TXDONE; + } + if (value & S_RXRDY) { + s->regs[R_SPI_RIS] &= ~S_RXRDY; + } + if (value & S_RXCHOVRF) { + s->regs[R_SPI_RIS] &= ~S_RXCHOVRF; + } + break; + + case R_SPI_MIS: + case R_SPI_STATUS: + case R_SPI_RIS: + qemu_log_mask(LOG_GUEST_ERROR, + "%s: Write to read only register 0x%" HWADDR_PRIx "\n", + __func__, addr * 4); + break; + + default: + if (addr < ARRAY_SIZE(s->regs)) { + s->regs[addr] = value; + } else { + qemu_log_mask(LOG_GUEST_ERROR, + "%s: Bad offset 0x%" HWADDR_PRIx "\n", __func__, + addr * 4); + } + break; + } + + spi_update_irq(s); +} + +static const MemoryRegionOps spi_ops = { + .read = spi_read, + .write = spi_write, + .endianness = DEVICE_NATIVE_ENDIAN, + .valid = { + .min_access_size = 1, + .max_access_size = 4 + } +}; + +static void mss_spi_realize(DeviceState *dev, Error **errp) +{ + MSSSpiState *s = MSS_SPI(dev); + SysBusDevice *sbd = SYS_BUS_DEVICE(dev); + + s->spi = ssi_create_bus(dev, "spi"); + + sysbus_init_irq(sbd, &s->irq); + ssi_auto_connect_slaves(dev, &s->cs_line, s->spi); + sysbus_init_irq(sbd, &s->cs_line); + + memory_region_init_io(&s->mmio, OBJECT(s), &spi_ops, s, + TYPE_MSS_SPI, R_SPI_MAX * 4); + sysbus_init_mmio(sbd, &s->mmio); + + fifo32_create(&s->tx_fifo, FIFO_CAPACITY); + fifo32_create(&s->rx_fifo, FIFO_CAPACITY); +} + +static const VMStateDescription vmstate_mss_spi = { + .name = TYPE_MSS_SPI, + .version_id = 1, + .minimum_version_id = 1, + .fields = (VMStateField[]) { + VMSTATE_FIFO32(tx_fifo, MSSSpiState), + VMSTATE_FIFO32(rx_fifo, MSSSpiState), + VMSTATE_UINT32_ARRAY(regs, MSSSpiState, R_SPI_MAX), + VMSTATE_END_OF_LIST() + } +}; + +static void mss_spi_class_init(ObjectClass *klass, void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + + dc->realize = mss_spi_realize; + dc->reset = mss_spi_reset; + dc->vmsd = &vmstate_mss_spi; +} + +static const TypeInfo mss_spi_info = { + .name = TYPE_MSS_SPI, + .parent = TYPE_SYS_BUS_DEVICE, + .instance_size = sizeof(MSSSpiState), + .class_init = mss_spi_class_init, +}; + +static void mss_spi_register_types(void) +{ + type_register_static(&mss_spi_info); +} + +type_init(mss_spi_register_types) -- 2.7.4 From: Subbaraya Sundeep <sundeep.lkml@gmail.com> Smartfusion2 SoC has hardened Microcontroller subsystem and flash based FPGA fabric. This patch adds support for Microcontroller subsystem in the SoC. Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 20170920201737.25723-5-f4bug@amsat.org [PMD: drop cpu_model to directly use cpu type, check m3clk non null] Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- hw/arm/Makefile.objs | 1 + include/hw/arm/msf2-soc.h | 67 +++++++++++ hw/arm/msf2-soc.c | 238 ++++++++++++++++++++++++++++++++++++++++ default-configs/arm-softmmu.mak | 1 + 4 files changed, 307 insertions(+) create mode 100644 include/hw/arm/msf2-soc.h create mode 100644 hw/arm/msf2-soc.c diff --git a/hw/arm/Makefile.objs b/hw/arm/Makefile.objs index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/Makefile.objs +++ b/hw/arm/Makefile.objs @@ -XXX,XX +XXX,XX @@ obj-$(CONFIG_FSL_IMX31) += fsl-imx31.o kzm.o obj-$(CONFIG_FSL_IMX6) += fsl-imx6.o sabrelite.o obj-$(CONFIG_ASPEED_SOC) += aspeed_soc.o aspeed.o obj-$(CONFIG_MPS2) += mps2.o +obj-$(CONFIG_MSF2) += msf2-soc.o diff --git a/include/hw/arm/msf2-soc.h b/include/hw/arm/msf2-soc.h new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/include/hw/arm/msf2-soc.h @@ -XXX,XX +XXX,XX @@ +/* + * Microsemi Smartfusion2 SoC + * + * Copyright (c) 2017 Subbaraya Sundeep <sundeep.lkml@gmail.com> + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#ifndef HW_ARM_MSF2_SOC_H +#define HW_ARM_MSF2_SOC_H + +#include "hw/arm/armv7m.h" +#include "hw/timer/mss-timer.h" +#include "hw/misc/msf2-sysreg.h" +#include "hw/ssi/mss-spi.h" + +#define TYPE_MSF2_SOC "msf2-soc" +#define MSF2_SOC(obj) OBJECT_CHECK(MSF2State, (obj), TYPE_MSF2_SOC) + +#define MSF2_NUM_SPIS 2 +#define MSF2_NUM_UARTS 2 + +/* + * System timer consists of two programmable 32-bit + * decrementing counters that generate individual interrupts to + * the Cortex-M3 processor + */ +#define MSF2_NUM_TIMERS 2 + +typedef struct MSF2State { + /*< private >*/ + SysBusDevice parent_obj; + /*< public >*/ + + ARMv7MState armv7m; + + char *cpu_type; + char *part_name; + uint64_t envm_size; + uint64_t esram_size; + + uint32_t m3clk; + uint8_t apb0div; + uint8_t apb1div; + + MSF2SysregState sysreg; + MSSTimerState timer; + MSSSpiState spi[MSF2_NUM_SPIS]; +} MSF2State; + +#endif diff --git a/hw/arm/msf2-soc.c b/hw/arm/msf2-soc.c new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/hw/arm/msf2-soc.c @@ -XXX,XX +XXX,XX @@ +/* + * SmartFusion2 SoC emulation. + * + * Copyright (c) 2017 Subbaraya Sundeep <sundeep.lkml@gmail.com> + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#include "qemu/osdep.h" +#include "qapi/error.h" +#include "qemu-common.h" +#include "hw/arm/arm.h" +#include "exec/address-spaces.h" +#include "hw/char/serial.h" +#include "hw/boards.h" +#include "sysemu/block-backend.h" +#include "qemu/cutils.h" +#include "hw/arm/msf2-soc.h" +#include "hw/misc/unimp.h" + +#define MSF2_TIMER_BASE 0x40004000 +#define MSF2_SYSREG_BASE 0x40038000 + +#define ENVM_BASE_ADDRESS 0x60000000 + +#define SRAM_BASE_ADDRESS 0x20000000 + +#define MSF2_ENVM_MAX_SIZE (512 * K_BYTE) + +/* + * eSRAM max size is 80k without SECDED(Single error correction and + * dual error detection) feature and 64k with SECDED. + * We do not support SECDED now. + */ +#define MSF2_ESRAM_MAX_SIZE (80 * K_BYTE) + +static const uint32_t spi_addr[MSF2_NUM_SPIS] = { 0x40001000 , 0x40011000 }; +static const uint32_t uart_addr[MSF2_NUM_UARTS] = { 0x40000000 , 0x40010000 }; + +static const int spi_irq[MSF2_NUM_SPIS] = { 2, 3 }; +static const int uart_irq[MSF2_NUM_UARTS] = { 10, 11 }; +static const int timer_irq[MSF2_NUM_TIMERS] = { 14, 15 }; + +static void m2sxxx_soc_initfn(Object *obj) +{ + MSF2State *s = MSF2_SOC(obj); + int i; + + object_initialize(&s->armv7m, sizeof(s->armv7m), TYPE_ARMV7M); + qdev_set_parent_bus(DEVICE(&s->armv7m), sysbus_get_default()); + + object_initialize(&s->sysreg, sizeof(s->sysreg), TYPE_MSF2_SYSREG); + qdev_set_parent_bus(DEVICE(&s->sysreg), sysbus_get_default()); + + object_initialize(&s->timer, sizeof(s->timer), TYPE_MSS_TIMER); + qdev_set_parent_bus(DEVICE(&s->timer), sysbus_get_default()); + + for (i = 0; i < MSF2_NUM_SPIS; i++) { + object_initialize(&s->spi[i], sizeof(s->spi[i]), + TYPE_MSS_SPI); + qdev_set_parent_bus(DEVICE(&s->spi[i]), sysbus_get_default()); + } +} + +static void m2sxxx_soc_realize(DeviceState *dev_soc, Error **errp) +{ + MSF2State *s = MSF2_SOC(dev_soc); + DeviceState *dev, *armv7m; + SysBusDevice *busdev; + Error *err = NULL; + int i; + + MemoryRegion *system_memory = get_system_memory(); + MemoryRegion *nvm = g_new(MemoryRegion, 1); + MemoryRegion *nvm_alias = g_new(MemoryRegion, 1); + MemoryRegion *sram = g_new(MemoryRegion, 1); + + memory_region_init_rom(nvm, NULL, "MSF2.eNVM", s->envm_size, + &error_fatal); + /* + * On power-on, the eNVM region 0x60000000 is automatically + * remapped to the Cortex-M3 processor executable region + * start address (0x0). We do not support remapping other eNVM, + * eSRAM and DDR regions by guest(via Sysreg) currently. + */ + memory_region_init_alias(nvm_alias, NULL, "MSF2.eNVM", + nvm, 0, s->envm_size); + + memory_region_add_subregion(system_memory, ENVM_BASE_ADDRESS, nvm); + memory_region_add_subregion(system_memory, 0, nvm_alias); + + memory_region_init_ram(sram, NULL, "MSF2.eSRAM", s->esram_size, + &error_fatal); + memory_region_add_subregion(system_memory, SRAM_BASE_ADDRESS, sram); + + armv7m = DEVICE(&s->armv7m); + qdev_prop_set_uint32(armv7m, "num-irq", 81); + qdev_prop_set_string(armv7m, "cpu-type", s->cpu_type); + object_property_set_link(OBJECT(&s->armv7m), OBJECT(get_system_memory()), + "memory", &error_abort); + object_property_set_bool(OBJECT(&s->armv7m), true, "realized", &err); + if (err != NULL) { + error_propagate(errp, err); + return; + } + + if (!s->m3clk) { + error_setg(errp, "Invalid m3clk value"); + error_append_hint(errp, "m3clk can not be zero\n"); + return; + } + system_clock_scale = NANOSECONDS_PER_SECOND / s->m3clk; + + for (i = 0; i < MSF2_NUM_UARTS; i++) { + if (serial_hds[i]) { + serial_mm_init(get_system_memory(), uart_addr[i], 2, + qdev_get_gpio_in(armv7m, uart_irq[i]), + 115200, serial_hds[i], DEVICE_NATIVE_ENDIAN); + } + } + + dev = DEVICE(&s->timer); + /* APB0 clock is the timer input clock */ + qdev_prop_set_uint32(dev, "clock-frequency", s->m3clk / s->apb0div); + object_property_set_bool(OBJECT(&s->timer), true, "realized", &err); + if (err != NULL) { + error_propagate(errp, err); + return; + } + busdev = SYS_BUS_DEVICE(dev); + sysbus_mmio_map(busdev, 0, MSF2_TIMER_BASE); + sysbus_connect_irq(busdev, 0, + qdev_get_gpio_in(armv7m, timer_irq[0])); + sysbus_connect_irq(busdev, 1, + qdev_get_gpio_in(armv7m, timer_irq[1])); + + dev = DEVICE(&s->sysreg); + qdev_prop_set_uint32(dev, "apb0divisor", s->apb0div); + qdev_prop_set_uint32(dev, "apb1divisor", s->apb1div); + object_property_set_bool(OBJECT(&s->sysreg), true, "realized", &err); + if (err != NULL) { + error_propagate(errp, err); + return; + } + busdev = SYS_BUS_DEVICE(dev); + sysbus_mmio_map(busdev, 0, MSF2_SYSREG_BASE); + + for (i = 0; i < MSF2_NUM_SPIS; i++) { + gchar *bus_name; + + object_property_set_bool(OBJECT(&s->spi[i]), true, "realized", &err); + if (err != NULL) { + error_propagate(errp, err); + return; + } + + sysbus_mmio_map(SYS_BUS_DEVICE(&s->spi[i]), 0, spi_addr[i]); + sysbus_connect_irq(SYS_BUS_DEVICE(&s->spi[i]), 0, + qdev_get_gpio_in(armv7m, spi_irq[i])); + + /* Alias controller SPI bus to the SoC itself */ + bus_name = g_strdup_printf("spi%d", i); + object_property_add_alias(OBJECT(s), bus_name, + OBJECT(&s->spi[i]), "spi", + &error_abort); + g_free(bus_name); + } + + /* Below devices are not modelled yet. */ + create_unimplemented_device("i2c_0", 0x40002000, 0x1000); + create_unimplemented_device("dma", 0x40003000, 0x1000); + create_unimplemented_device("watchdog", 0x40005000, 0x1000); + create_unimplemented_device("i2c_1", 0x40012000, 0x1000); + create_unimplemented_device("gpio", 0x40013000, 0x1000); + create_unimplemented_device("hs-dma", 0x40014000, 0x1000); + create_unimplemented_device("can", 0x40015000, 0x1000); + create_unimplemented_device("rtc", 0x40017000, 0x1000); + create_unimplemented_device("apb_config", 0x40020000, 0x10000); + create_unimplemented_device("emac", 0x40041000, 0x1000); + create_unimplemented_device("usb", 0x40043000, 0x1000); +} + +static Property m2sxxx_soc_properties[] = { + /* + * part name specifies the type of SmartFusion2 device variant(this + * property is for information purpose only. + */ + DEFINE_PROP_STRING("cpu-type", MSF2State, cpu_type), + DEFINE_PROP_STRING("part-name", MSF2State, part_name), + DEFINE_PROP_UINT64("eNVM-size", MSF2State, envm_size, MSF2_ENVM_MAX_SIZE), + DEFINE_PROP_UINT64("eSRAM-size", MSF2State, esram_size, + MSF2_ESRAM_MAX_SIZE), + /* Libero GUI shows 100Mhz as default for clocks */ + DEFINE_PROP_UINT32("m3clk", MSF2State, m3clk, 100 * 1000000), + /* default divisors in Libero GUI */ + DEFINE_PROP_UINT8("apb0div", MSF2State, apb0div, 2), + DEFINE_PROP_UINT8("apb1div", MSF2State, apb1div, 2), + DEFINE_PROP_END_OF_LIST(), +}; + +static void m2sxxx_soc_class_init(ObjectClass *klass, void *data) +{ + DeviceClass *dc = DEVICE_CLASS(klass); + + dc->realize = m2sxxx_soc_realize; + dc->props = m2sxxx_soc_properties; +} + +static const TypeInfo m2sxxx_soc_info = { + .name = TYPE_MSF2_SOC, + .parent = TYPE_SYS_BUS_DEVICE, + .instance_size = sizeof(MSF2State), + .instance_init = m2sxxx_soc_initfn, + .class_init = m2sxxx_soc_class_init, +}; + +static void m2sxxx_soc_types(void) +{ + type_register_static(&m2sxxx_soc_info); +} + +type_init(m2sxxx_soc_types) diff --git a/default-configs/arm-softmmu.mak b/default-configs/arm-softmmu.mak index XXXXXXX..XXXXXXX 100644 --- a/default-configs/arm-softmmu.mak +++ b/default-configs/arm-softmmu.mak @@ -XXX,XX +XXX,XX @@ CONFIG_ACPI=y CONFIG_SMBIOS=y CONFIG_ASPEED_SOC=y CONFIG_GPIO_KEY=y +CONFIG_MSF2=y -- 2.7.4 From: Subbaraya Sundeep <sundeep.lkml@gmail.com> Emulated Emcraft's Smartfusion2 System On Module starter kit. Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 20170920201737.25723-6-f4bug@amsat.org [PMD: drop cpu_model to directly use cpu type] Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- hw/arm/Makefile.objs | 2 +- hw/arm/msf2-som.c | 105 +++++++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 106 insertions(+), 1 deletion(-) create mode 100644 hw/arm/msf2-som.c diff --git a/hw/arm/Makefile.objs b/hw/arm/Makefile.objs index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/Makefile.objs +++ b/hw/arm/Makefile.objs @@ -XXX,XX +XXX,XX @@ obj-$(CONFIG_FSL_IMX31) += fsl-imx31.o kzm.o obj-$(CONFIG_FSL_IMX6) += fsl-imx6.o sabrelite.o obj-$(CONFIG_ASPEED_SOC) += aspeed_soc.o aspeed.o obj-$(CONFIG_MPS2) += mps2.o -obj-$(CONFIG_MSF2) += msf2-soc.o +obj-$(CONFIG_MSF2) += msf2-soc.o msf2-som.o diff --git a/hw/arm/msf2-som.c b/hw/arm/msf2-som.c new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/hw/arm/msf2-som.c @@ -XXX,XX +XXX,XX @@ +/* + * SmartFusion2 SOM starter kit(from Emcraft) emulation. + * + * Copyright (c) 2017 Subbaraya Sundeep <sundeep.lkml@gmail.com> + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#include "qemu/osdep.h" +#include "qapi/error.h" +#include "qemu/error-report.h" +#include "hw/boards.h" +#include "hw/arm/arm.h" +#include "exec/address-spaces.h" +#include "qemu/cutils.h" +#include "hw/arm/msf2-soc.h" +#include "cpu.h" + +#define DDR_BASE_ADDRESS 0xA0000000 +#define DDR_SIZE (64 * M_BYTE) + +#define M2S010_ENVM_SIZE (256 * K_BYTE) +#define M2S010_ESRAM_SIZE (64 * K_BYTE) + +static void emcraft_sf2_s2s010_init(MachineState *machine) +{ + DeviceState *dev; + DeviceState *spi_flash; + MSF2State *soc; + MachineClass *mc = MACHINE_GET_CLASS(machine); + DriveInfo *dinfo = drive_get_next(IF_MTD); + qemu_irq cs_line; + SSIBus *spi_bus; + MemoryRegion *sysmem = get_system_memory(); + MemoryRegion *ddr = g_new(MemoryRegion, 1); + + if (strcmp(machine->cpu_type, mc->default_cpu_type) != 0) { + error_report("This board can only be used with CPU %s", + mc->default_cpu_type); + } + + memory_region_init_ram(ddr, NULL, "ddr-ram", DDR_SIZE, + &error_fatal); + memory_region_add_subregion(sysmem, DDR_BASE_ADDRESS, ddr); + + dev = qdev_create(NULL, TYPE_MSF2_SOC); + qdev_prop_set_string(dev, "part-name", "M2S010"); + qdev_prop_set_string(dev, "cpu-type", mc->default_cpu_type); + + qdev_prop_set_uint64(dev, "eNVM-size", M2S010_ENVM_SIZE); + qdev_prop_set_uint64(dev, "eSRAM-size", M2S010_ESRAM_SIZE); + + /* + * CPU clock and peripheral clocks(APB0, APB1)are configurable + * in Libero. CPU clock is divided by APB0 and APB1 divisors for + * peripherals. Emcraft's SoM kit comes with these settings by default. + */ + qdev_prop_set_uint32(dev, "m3clk", 142 * 1000000); + qdev_prop_set_uint32(dev, "apb0div", 2); + qdev_prop_set_uint32(dev, "apb1div", 2); + + object_property_set_bool(OBJECT(dev), true, "realized", &error_fatal); + + soc = MSF2_SOC(dev); + + /* Attach SPI flash to SPI0 controller */ + spi_bus = (SSIBus *)qdev_get_child_bus(dev, "spi0"); + spi_flash = ssi_create_slave_no_init(spi_bus, "s25sl12801"); + qdev_prop_set_uint8(spi_flash, "spansion-cr2nv", 1); + if (dinfo) { + qdev_prop_set_drive(spi_flash, "drive", blk_by_legacy_dinfo(dinfo), + &error_fatal); + } + qdev_init_nofail(spi_flash); + cs_line = qdev_get_gpio_in_named(spi_flash, SSI_GPIO_CS, 0); + sysbus_connect_irq(SYS_BUS_DEVICE(&soc->spi[0]), 1, cs_line); + + armv7m_load_kernel(ARM_CPU(first_cpu), machine->kernel_filename, + soc->envm_size); +} + +static void emcraft_sf2_machine_init(MachineClass *mc) +{ + mc->desc = "SmartFusion2 SOM kit from Emcraft (M2S010)"; + mc->init = emcraft_sf2_s2s010_init; + mc->default_cpu_type = ARM_CPU_TYPE_NAME("cortex-m3"); +} + +DEFINE_MACHINE("emcraft-sf2", emcraft_sf2_machine_init) -- 2.7.4 First arm pullreq for 7.1. The bulk of this is the qemu_split_irq removal. I have enough stuff in my to-review queue that I expect to do another pullreq early next week, but 31 patches is enough to not hang on to. thanks -- PMM The following changes since commit 9c125d17e9402c232c46610802e5931b3639d77b: Merge tag 'pull-tcg-20220420' of https://gitlab.com/rth7680/qemu into staging (2022-04-20 16:43:11 -0700) are available in the Git repository at: https://git.linaro.org/people/pmaydell/qemu-arm.git tags/pull-target-arm-20220421 for you to fetch changes up to 5b415dd61bdbf61fb4be0e9f1a7172b8bce682c6: hw/arm: Use bit fields for NPCM7XX PWRON STRAPs (2022-04-21 11:37:05 +0100) ---------------------------------------------------------------- target-arm queue: * hw/arm/virt: Check for attempt to use TrustZone with KVM or HVF * versal: Add the Cortex-R5s in the Real-Time Processing Unit (RPU) subsystem * versal: model enough of the Clock/Reset Low-power domain (CRL) to allow control of the Cortex-R5s * xlnx-zynqmp: Connect 4 TTC timers * exynos4210: Refactor GIC/combiner code to stop using qemu_split_irq * realview: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ' * stellaris: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ' * hw/core/irq: remove unused 'qemu_irq_split' function * npcm7xx: use symbolic constants for PWRON STRAP bit fields * virt: document impact of gic-version on max CPUs ---------------------------------------------------------------- Edgar E. Iglesias (6): timer: cadence_ttc: Break out header file to allow embedding hw/arm/xlnx-zynqmp: Connect 4 TTC timers hw/arm: versal: Create an APU CPU Cluster hw/arm: versal: Add the Cortex-R5Fs hw/misc: Add a model of the Xilinx Versal CRL hw/arm: versal: Connect the CRL Hao Wu (2): hw/misc: Add PWRON STRAP bit fields in GCR module hw/arm: Use bit fields for NPCM7XX PWRON STRAPs Heinrich Schuchardt (1): hw/arm/virt: impact of gic-version on max CPUs Peter Maydell (19): hw/arm/virt: Check for attempt to use TrustZone with KVM or HVF hw/arm/exynos4210: Use TYPE_OR_IRQ instead of custom OR-gate device hw/intc/exynos4210_gic: Remove unused TYPE_EXYNOS4210_IRQ_GATE hw/arm/exynos4210: Put a9mpcore device into state struct hw/arm/exynos4210: Drop int_gic_irq[] from Exynos4210Irq struct hw/arm/exynos4210: Coalesce board_irqs and irq_table hw/arm/exynos4210: Fix code style nit in combiner_grp_to_gic_id[] hw/arm/exynos4210: Move exynos4210_init_board_irqs() into exynos4210.c hw/arm/exynos4210: Put external GIC into state struct hw/arm/exynos4210: Drop ext_gic_irq[] from Exynos4210Irq struct hw/arm/exynos4210: Move exynos4210_combiner_get_gpioin() into exynos4210.c hw/arm/exynos4210: Delete unused macro definitions hw/arm/exynos4210: Use TYPE_SPLIT_IRQ in exynos4210_init_board_irqs() hw/arm/exynos4210: Fill in irq_table[] for internal-combiner-only IRQ lines hw/arm/exynos4210: Connect MCT_G0 and MCT_G1 to both combiners hw/arm/exynos4210: Don't connect multiple lines to external GIC inputs hw/arm/exynos4210: Fold combiner splits into exynos4210_init_board_irqs() hw/arm/exynos4210: Put combiners into state struct hw/arm/exynos4210: Drop Exynos4210Irq struct Zongyuan Li (3): hw/arm/realview: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ' hw/arm/stellaris: replace 'qemu_split_irq' with 'TYPE_SPLIT_IRQ' hw/core/irq: remove unused 'qemu_irq_split' function docs/system/arm/virt.rst | 4 +- include/hw/arm/exynos4210.h | 50 ++-- include/hw/arm/xlnx-versal.h | 16 ++ include/hw/arm/xlnx-zynqmp.h | 4 + include/hw/intc/exynos4210_combiner.h | 57 +++++ include/hw/intc/exynos4210_gic.h | 43 ++++ include/hw/irq.h | 5 - include/hw/misc/npcm7xx_gcr.h | 30 +++ include/hw/misc/xlnx-versal-crl.h | 235 +++++++++++++++++++ include/hw/timer/cadence_ttc.h | 54 +++++ hw/arm/exynos4210.c | 430 ++++++++++++++++++++++++++++++---- hw/arm/npcm7xx_boards.c | 24 +- hw/arm/realview.c | 33 ++- hw/arm/stellaris.c | 15 +- hw/arm/virt.c | 7 + hw/arm/xlnx-versal-virt.c | 6 +- hw/arm/xlnx-versal.c | 99 +++++++- hw/arm/xlnx-zynqmp.c | 22 ++ hw/core/irq.c | 15 -- hw/intc/exynos4210_combiner.c | 108 +-------- hw/intc/exynos4210_gic.c | 344 +-------------------------- hw/misc/xlnx-versal-crl.c | 421 +++++++++++++++++++++++++++++++++ hw/timer/cadence_ttc.c | 32 +-- MAINTAINERS | 2 +- hw/misc/meson.build | 1 + 25 files changed, 1457 insertions(+), 600 deletions(-) create mode 100644 include/hw/intc/exynos4210_combiner.h create mode 100644 include/hw/intc/exynos4210_gic.h create mode 100644 include/hw/misc/xlnx-versal-crl.h create mode 100644 include/hw/timer/cadence_ttc.h create mode 100644 hw/misc/xlnx-versal-crl.c It's not possible to provide the guest with the Security extensions (TrustZone) when using KVM or HVF, because the hardware virtualization extensions don't permit running EL3 guest code. However, we weren't checking for this combination, with the result that QEMU would assert if you tried it: $ qemu-system-aarch64 -enable-kvm -machine virt,secure=on -cpu host -display none Unexpected error in object_property_find_err() at ../../qom/object.c:1304: qemu-system-aarch64: Property 'host-arm-cpu.secure-memory' not found Aborted Check for this combination of options and report an error, in the same way we already do for attempts to give a KVM or HVF guest the Virtualization or MTE extensions. Now we will report: qemu-system-aarch64: mach-virt: KVM does not support providing Security extensions (TrustZone) to the guest CPU Resolves: https://gitlab.com/qemu-project/qemu/-/issues/961 Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404155301.566542-1-peter.maydell@linaro.org --- hw/arm/virt.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/hw/arm/virt.c b/hw/arm/virt.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/virt.c +++ b/hw/arm/virt.c @@ -XXX,XX +XXX,XX @@ static void machvirt_init(MachineState *machine) exit(1); } + if (vms->secure && (kvm_enabled() || hvf_enabled())) { + error_report("mach-virt: %s does not support providing " + "Security extensions (TrustZone) to the guest CPU", + kvm_enabled() ? "KVM" : "HVF"); + exit(1); + } + if (vms->virt && (kvm_enabled() || hvf_enabled())) { error_report("mach-virt: %s does not support providing " "Virtualization extensions to the guest CPU", -- 2.25.1 From: "Edgar E. Iglesias" <edgar.iglesias@amd.com> Break out header file to allow embedding of the the TTC. Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Luc Michel <luc@lmichel.fr> Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com> Message-id: 20220331222017.2914409-2-edgar.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- include/hw/timer/cadence_ttc.h | 54 ++++++++++++++++++++++++++++++++++ hw/timer/cadence_ttc.c | 32 ++------------------ 2 files changed, 56 insertions(+), 30 deletions(-) create mode 100644 include/hw/timer/cadence_ttc.h diff --git a/include/hw/timer/cadence_ttc.h b/include/hw/timer/cadence_ttc.h new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/include/hw/timer/cadence_ttc.h @@ -XXX,XX +XXX,XX @@ +/* + * Xilinx Zynq cadence TTC model + * + * Copyright (c) 2011 Xilinx Inc. + * Copyright (c) 2012 Peter A.G. Crosthwaite (peter.crosthwaite@petalogix.com) + * Copyright (c) 2012 PetaLogix Pty Ltd. + * Written By Haibing Ma + * M. Habib + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, see <http://www.gnu.org/licenses/>. + */ +#ifndef HW_TIMER_CADENCE_TTC_H +#define HW_TIMER_CADENCE_TTC_H + +#include "hw/sysbus.h" +#include "qemu/timer.h" + +typedef struct { + QEMUTimer *timer; + int freq; + + uint32_t reg_clock; + uint32_t reg_count; + uint32_t reg_value; + uint16_t reg_interval; + uint16_t reg_match[3]; + uint32_t reg_intr; + uint32_t reg_intr_en; + uint32_t reg_event_ctrl; + uint32_t reg_event; + + uint64_t cpu_time; + unsigned int cpu_time_valid; + + qemu_irq irq; +} CadenceTimerState; + +#define TYPE_CADENCE_TTC "cadence_ttc" +OBJECT_DECLARE_SIMPLE_TYPE(CadenceTTCState, CADENCE_TTC) + +struct CadenceTTCState { + SysBusDevice parent_obj; + + MemoryRegion iomem; + CadenceTimerState timer[3]; +}; + +#endif diff --git a/hw/timer/cadence_ttc.c b/hw/timer/cadence_ttc.c index XXXXXXX..XXXXXXX 100644 --- a/hw/timer/cadence_ttc.c +++ b/hw/timer/cadence_ttc.c @@ -XXX,XX +XXX,XX @@ #include "qemu/timer.h" #include "qom/object.h" +#include "hw/timer/cadence_ttc.h" + #ifdef CADENCE_TTC_ERR_DEBUG #define DB_PRINT(...) do { \ fprintf(stderr, ": %s: ", __func__); \ @@ -XXX,XX +XXX,XX @@ #define CLOCK_CTRL_PS_EN 0x00000001 #define CLOCK_CTRL_PS_V 0x0000001e -typedef struct { - QEMUTimer *timer; - int freq; - - uint32_t reg_clock; - uint32_t reg_count; - uint32_t reg_value; - uint16_t reg_interval; - uint16_t reg_match[3]; - uint32_t reg_intr; - uint32_t reg_intr_en; - uint32_t reg_event_ctrl; - uint32_t reg_event; - - uint64_t cpu_time; - unsigned int cpu_time_valid; - - qemu_irq irq; -} CadenceTimerState; - -#define TYPE_CADENCE_TTC "cadence_ttc" -OBJECT_DECLARE_SIMPLE_TYPE(CadenceTTCState, CADENCE_TTC) - -struct CadenceTTCState { - SysBusDevice parent_obj; - - MemoryRegion iomem; - CadenceTimerState timer[3]; -}; - static void cadence_timer_update(CadenceTimerState *s) { qemu_set_irq(s->irq, !!(s->reg_intr & s->reg_intr_en)); -- 2.25.1 From: "Edgar E. Iglesias" <edgar.iglesias@amd.com> Connect the 4 TTC timers on the ZynqMP. Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Luc Michel <luc@lmichel.fr> Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com> Message-id: 20220331222017.2914409-3-edgar.iglesias@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- include/hw/arm/xlnx-zynqmp.h | 4 ++++ hw/arm/xlnx-zynqmp.c | 22 ++++++++++++++++++++++ 2 files changed, 26 insertions(+) diff --git a/include/hw/arm/xlnx-zynqmp.h b/include/hw/arm/xlnx-zynqmp.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/xlnx-zynqmp.h +++ b/include/hw/arm/xlnx-zynqmp.h @@ -XXX,XX +XXX,XX @@ #include "hw/or-irq.h" #include "hw/misc/xlnx-zynqmp-apu-ctrl.h" #include "hw/misc/xlnx-zynqmp-crf.h" +#include "hw/timer/cadence_ttc.h" #define TYPE_XLNX_ZYNQMP "xlnx-zynqmp" OBJECT_DECLARE_SIMPLE_TYPE(XlnxZynqMPState, XLNX_ZYNQMP) @@ -XXX,XX +XXX,XX @@ OBJECT_DECLARE_SIMPLE_TYPE(XlnxZynqMPState, XLNX_ZYNQMP) #define XLNX_ZYNQMP_MAX_RAM_SIZE (XLNX_ZYNQMP_MAX_LOW_RAM_SIZE + \ XLNX_ZYNQMP_MAX_HIGH_RAM_SIZE) +#define XLNX_ZYNQMP_NUM_TTC 4 + /* * Unimplemented mmio regions needed to boot some images. */ @@ -XXX,XX +XXX,XX @@ struct XlnxZynqMPState { qemu_or_irq qspi_irq_orgate; XlnxZynqMPAPUCtrl apu_ctrl; XlnxZynqMPCRF crf; + CadenceTTCState ttc[XLNX_ZYNQMP_NUM_TTC]; char *boot_cpu; ARMCPU *boot_cpu_ptr; diff --git a/hw/arm/xlnx-zynqmp.c b/hw/arm/xlnx-zynqmp.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/xlnx-zynqmp.c +++ b/hw/arm/xlnx-zynqmp.c @@ -XXX,XX +XXX,XX @@ #define APU_ADDR 0xfd5c0000 #define APU_IRQ 153 +#define TTC0_ADDR 0xFF110000 +#define TTC0_IRQ 36 + #define IPI_ADDR 0xFF300000 #define IPI_IRQ 64 @@ -XXX,XX +XXX,XX @@ static void xlnx_zynqmp_create_crf(XlnxZynqMPState *s, qemu_irq *gic) sysbus_connect_irq(sbd, 0, gic[CRF_IRQ]); } +static void xlnx_zynqmp_create_ttc(XlnxZynqMPState *s, qemu_irq *gic) +{ + SysBusDevice *sbd; + int i, irq; + + for (i = 0; i < XLNX_ZYNQMP_NUM_TTC; i++) { + object_initialize_child(OBJECT(s), "ttc[*]", &s->ttc[i], + TYPE_CADENCE_TTC); + sbd = SYS_BUS_DEVICE(&s->ttc[i]); + + sysbus_realize(sbd, &error_fatal); + sysbus_mmio_map(sbd, 0, TTC0_ADDR + i * 0x10000); + for (irq = 0; irq < 3; irq++) { + sysbus_connect_irq(sbd, irq, gic[TTC0_IRQ + i * 3 + irq]); + } + } +} + static void xlnx_zynqmp_create_unimp_mmio(XlnxZynqMPState *s) { static const struct UnimpInfo { @@ -XXX,XX +XXX,XX @@ static void xlnx_zynqmp_realize(DeviceState *dev, Error **errp) xlnx_zynqmp_create_efuse(s, gic_spi); xlnx_zynqmp_create_apu_ctrl(s, gic_spi); xlnx_zynqmp_create_crf(s, gic_spi); + xlnx_zynqmp_create_ttc(s, gic_spi); xlnx_zynqmp_create_unimp_mmio(s); for (i = 0; i < XLNX_ZYNQMP_NUM_GDMA_CH; i++) { -- 2.25.1 From: "Edgar E. Iglesias" <edgar.iglesias@amd.com> Create an APU CPU Cluster. This is in preparation to add the RPU. Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com> Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com> Message-id: 20220406174303.2022038-2-edgar.iglesias@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- include/hw/arm/xlnx-versal.h | 2 ++ hw/arm/xlnx-versal.c | 9 ++++++++- 2 files changed, 10 insertions(+), 1 deletion(-) diff --git a/include/hw/arm/xlnx-versal.h b/include/hw/arm/xlnx-versal.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/xlnx-versal.h +++ b/include/hw/arm/xlnx-versal.h @@ -XXX,XX +XXX,XX @@ #include "hw/sysbus.h" #include "hw/arm/boot.h" +#include "hw/cpu/cluster.h" #include "hw/or-irq.h" #include "hw/sd/sdhci.h" #include "hw/intc/arm_gicv3.h" @@ -XXX,XX +XXX,XX @@ struct Versal { struct { struct { MemoryRegion mr; + CPUClusterState cluster; ARMCPU cpu[XLNX_VERSAL_NR_ACPUS]; GICv3State gic; } apu; diff --git a/hw/arm/xlnx-versal.c b/hw/arm/xlnx-versal.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/xlnx-versal.c +++ b/hw/arm/xlnx-versal.c @@ -XXX,XX +XXX,XX @@ static void versal_create_apu_cpus(Versal *s) { int i; + object_initialize_child(OBJECT(s), "apu-cluster", &s->fpd.apu.cluster, + TYPE_CPU_CLUSTER); + qdev_prop_set_uint32(DEVICE(&s->fpd.apu.cluster), "cluster-id", 0); + for (i = 0; i < ARRAY_SIZE(s->fpd.apu.cpu); i++) { Object *obj; - object_initialize_child(OBJECT(s), "apu-cpu[*]", &s->fpd.apu.cpu[i], + object_initialize_child(OBJECT(&s->fpd.apu.cluster), + "apu-cpu[*]", &s->fpd.apu.cpu[i], XLNX_VERSAL_ACPU_TYPE); obj = OBJECT(&s->fpd.apu.cpu[i]); if (i) { @@ -XXX,XX +XXX,XX @@ static void versal_create_apu_cpus(Versal *s) &error_abort); qdev_realize(DEVICE(obj), NULL, &error_fatal); } + + qdev_realize(DEVICE(&s->fpd.apu.cluster), NULL, &error_fatal); } static void versal_create_apu_gic(Versal *s, qemu_irq *pic) -- 2.25.1 From: "Edgar E. Iglesias" <edgar.iglesias@amd.com> Add the Cortex-R5Fs of the Versal RPU (Real-time Processing Unit) subsystem. Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com> Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com> Message-id: 20220406174303.2022038-3-edgar.iglesias@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- include/hw/arm/xlnx-versal.h | 10 ++++++++++ hw/arm/xlnx-versal-virt.c | 6 +++--- hw/arm/xlnx-versal.c | 36 ++++++++++++++++++++++++++++++++++++ 3 files changed, 49 insertions(+), 3 deletions(-) diff --git a/include/hw/arm/xlnx-versal.h b/include/hw/arm/xlnx-versal.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/xlnx-versal.h +++ b/include/hw/arm/xlnx-versal.h @@ -XXX,XX +XXX,XX @@ OBJECT_DECLARE_SIMPLE_TYPE(Versal, XLNX_VERSAL) #define XLNX_VERSAL_NR_ACPUS 2 +#define XLNX_VERSAL_NR_RCPUS 2 #define XLNX_VERSAL_NR_UARTS 2 #define XLNX_VERSAL_NR_GEMS 2 #define XLNX_VERSAL_NR_ADMAS 8 @@ -XXX,XX +XXX,XX @@ struct Versal { VersalUsb2 usb; } iou; + /* Real-time Processing Unit. */ + struct { + MemoryRegion mr; + MemoryRegion mr_ps_alias; + + CPUClusterState cluster; + ARMCPU cpu[XLNX_VERSAL_NR_RCPUS]; + } rpu; + struct { qemu_or_irq irq_orgate; XlnxXramCtrl ctrl[XLNX_VERSAL_NR_XRAM]; diff --git a/hw/arm/xlnx-versal-virt.c b/hw/arm/xlnx-versal-virt.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/xlnx-versal-virt.c +++ b/hw/arm/xlnx-versal-virt.c @@ -XXX,XX +XXX,XX @@ static void versal_virt_machine_class_init(ObjectClass *oc, void *data) mc->desc = "Xilinx Versal Virtual development board"; mc->init = versal_virt_init; - mc->min_cpus = XLNX_VERSAL_NR_ACPUS; - mc->max_cpus = XLNX_VERSAL_NR_ACPUS; - mc->default_cpus = XLNX_VERSAL_NR_ACPUS; + mc->min_cpus = XLNX_VERSAL_NR_ACPUS + XLNX_VERSAL_NR_RCPUS; + mc->max_cpus = XLNX_VERSAL_NR_ACPUS + XLNX_VERSAL_NR_RCPUS; + mc->default_cpus = XLNX_VERSAL_NR_ACPUS + XLNX_VERSAL_NR_RCPUS; mc->no_cdrom = true; mc->default_ram_id = "ddr"; } diff --git a/hw/arm/xlnx-versal.c b/hw/arm/xlnx-versal.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/xlnx-versal.c +++ b/hw/arm/xlnx-versal.c @@ -XXX,XX +XXX,XX @@ #include "hw/sysbus.h" #define XLNX_VERSAL_ACPU_TYPE ARM_CPU_TYPE_NAME("cortex-a72") +#define XLNX_VERSAL_RCPU_TYPE ARM_CPU_TYPE_NAME("cortex-r5f") #define GEM_REVISION 0x40070106 #define VERSAL_NUM_PMC_APB_IRQS 3 @@ -XXX,XX +XXX,XX @@ static void versal_create_apu_gic(Versal *s, qemu_irq *pic) } } +static void versal_create_rpu_cpus(Versal *s) +{ + int i; + + object_initialize_child(OBJECT(s), "rpu-cluster", &s->lpd.rpu.cluster, + TYPE_CPU_CLUSTER); + qdev_prop_set_uint32(DEVICE(&s->lpd.rpu.cluster), "cluster-id", 1); + + for (i = 0; i < ARRAY_SIZE(s->lpd.rpu.cpu); i++) { + Object *obj; + + object_initialize_child(OBJECT(&s->lpd.rpu.cluster), + "rpu-cpu[*]", &s->lpd.rpu.cpu[i], + XLNX_VERSAL_RCPU_TYPE); + obj = OBJECT(&s->lpd.rpu.cpu[i]); + object_property_set_bool(obj, "start-powered-off", true, + &error_abort); + + object_property_set_int(obj, "mp-affinity", 0x100 | i, &error_abort); + object_property_set_int(obj, "core-count", ARRAY_SIZE(s->lpd.rpu.cpu), + &error_abort); + object_property_set_link(obj, "memory", OBJECT(&s->lpd.rpu.mr), + &error_abort); + qdev_realize(DEVICE(obj), NULL, &error_fatal); + } + + qdev_realize(DEVICE(&s->lpd.rpu.cluster), NULL, &error_fatal); +} + static void versal_create_uarts(Versal *s, qemu_irq *pic) { int i; @@ -XXX,XX +XXX,XX @@ static void versal_realize(DeviceState *dev, Error **errp) versal_create_apu_cpus(s); versal_create_apu_gic(s, pic); + versal_create_rpu_cpus(s); versal_create_uarts(s, pic); versal_create_usbs(s, pic); versal_create_gems(s, pic); @@ -XXX,XX +XXX,XX @@ static void versal_realize(DeviceState *dev, Error **errp) memory_region_add_subregion_overlap(&s->mr_ps, MM_OCM, &s->lpd.mr_ocm, 0); memory_region_add_subregion_overlap(&s->fpd.apu.mr, 0, &s->mr_ps, 0); + memory_region_add_subregion_overlap(&s->lpd.rpu.mr, 0, + &s->lpd.rpu.mr_ps_alias, 0); } static void versal_init(Object *obj) @@ -XXX,XX +XXX,XX @@ static void versal_init(Object *obj) Versal *s = XLNX_VERSAL(obj); memory_region_init(&s->fpd.apu.mr, obj, "mr-apu", UINT64_MAX); + memory_region_init(&s->lpd.rpu.mr, obj, "mr-rpu", UINT64_MAX); memory_region_init(&s->mr_ps, obj, "mr-ps-switch", UINT64_MAX); + memory_region_init_alias(&s->lpd.rpu.mr_ps_alias, OBJECT(s), + "mr-rpu-ps-alias", &s->mr_ps, 0, UINT64_MAX); } static Property versal_properties[] = { -- 2.25.1 From: "Edgar E. Iglesias" <edgar.iglesias@amd.com> Add a model of the Xilinx Versal CRL. Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com> Reviewed-by: Frederic Konrad <fkonrad@amd.com> Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com> Message-id: 20220406174303.2022038-4-edgar.iglesias@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- include/hw/misc/xlnx-versal-crl.h | 235 +++++++++++++++++ hw/misc/xlnx-versal-crl.c | 421 ++++++++++++++++++++++++++++++ hw/misc/meson.build | 1 + 3 files changed, 657 insertions(+) create mode 100644 include/hw/misc/xlnx-versal-crl.h create mode 100644 hw/misc/xlnx-versal-crl.c diff --git a/include/hw/misc/xlnx-versal-crl.h b/include/hw/misc/xlnx-versal-crl.h new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/include/hw/misc/xlnx-versal-crl.h @@ -XXX,XX +XXX,XX @@ +/* + * QEMU model of the Clock-Reset-LPD (CRL). + * + * Copyright (c) 2022 Xilinx Inc. + * SPDX-License-Identifier: GPL-2.0-or-later + * + * Written by Edgar E. Iglesias <edgar.iglesias@xilinx.com> + */ +#ifndef HW_MISC_XLNX_VERSAL_CRL_H +#define HW_MISC_XLNX_VERSAL_CRL_H + +#include "hw/sysbus.h" +#include "hw/register.h" +#include "target/arm/cpu.h" + +#define TYPE_XLNX_VERSAL_CRL "xlnx,versal-crl" +OBJECT_DECLARE_SIMPLE_TYPE(XlnxVersalCRL, XLNX_VERSAL_CRL) + +REG32(ERR_CTRL, 0x0) + FIELD(ERR_CTRL, SLVERR_ENABLE, 0, 1) +REG32(IR_STATUS, 0x4) + FIELD(IR_STATUS, ADDR_DECODE_ERR, 0, 1) +REG32(IR_MASK, 0x8) + FIELD(IR_MASK, ADDR_DECODE_ERR, 0, 1) +REG32(IR_ENABLE, 0xc) + FIELD(IR_ENABLE, ADDR_DECODE_ERR, 0, 1) +REG32(IR_DISABLE, 0x10) + FIELD(IR_DISABLE, ADDR_DECODE_ERR, 0, 1) +REG32(WPROT, 0x1c) + FIELD(WPROT, ACTIVE, 0, 1) +REG32(PLL_CLK_OTHER_DMN, 0x20) + FIELD(PLL_CLK_OTHER_DMN, APLL_BYPASS, 0, 1) +REG32(RPLL_CTRL, 0x40) + FIELD(RPLL_CTRL, POST_SRC, 24, 3) + FIELD(RPLL_CTRL, PRE_SRC, 20, 3) + FIELD(RPLL_CTRL, CLKOUTDIV, 16, 2) + FIELD(RPLL_CTRL, FBDIV, 8, 8) + FIELD(RPLL_CTRL, BYPASS, 3, 1) + FIELD(RPLL_CTRL, RESET, 0, 1) +REG32(RPLL_CFG, 0x44) + FIELD(RPLL_CFG, LOCK_DLY, 25, 7) + FIELD(RPLL_CFG, LOCK_CNT, 13, 10) + FIELD(RPLL_CFG, LFHF, 10, 2) + FIELD(RPLL_CFG, CP, 5, 4) + FIELD(RPLL_CFG, RES, 0, 4) +REG32(RPLL_FRAC_CFG, 0x48) + FIELD(RPLL_FRAC_CFG, ENABLED, 31, 1) + FIELD(RPLL_FRAC_CFG, SEED, 22, 3) + FIELD(RPLL_FRAC_CFG, ALGRTHM, 19, 1) + FIELD(RPLL_FRAC_CFG, ORDER, 18, 1) + FIELD(RPLL_FRAC_CFG, DATA, 0, 16) +REG32(PLL_STATUS, 0x50) + FIELD(PLL_STATUS, RPLL_STABLE, 2, 1) + FIELD(PLL_STATUS, RPLL_LOCK, 0, 1) +REG32(RPLL_TO_XPD_CTRL, 0x100) + FIELD(RPLL_TO_XPD_CTRL, CLKACT, 25, 1) + FIELD(RPLL_TO_XPD_CTRL, DIVISOR0, 8, 10) +REG32(LPD_TOP_SWITCH_CTRL, 0x104) + FIELD(LPD_TOP_SWITCH_CTRL, CLKACT_ADMA, 26, 1) + FIELD(LPD_TOP_SWITCH_CTRL, CLKACT, 25, 1) + FIELD(LPD_TOP_SWITCH_CTRL, DIVISOR0, 8, 10) + FIELD(LPD_TOP_SWITCH_CTRL, SRCSEL, 0, 3) +REG32(LPD_LSBUS_CTRL, 0x108) + FIELD(LPD_LSBUS_CTRL, CLKACT, 25, 1) + FIELD(LPD_LSBUS_CTRL, DIVISOR0, 8, 10) + FIELD(LPD_LSBUS_CTRL, SRCSEL, 0, 3) +REG32(CPU_R5_CTRL, 0x10c) + FIELD(CPU_R5_CTRL, CLKACT_OCM2, 28, 1) + FIELD(CPU_R5_CTRL, CLKACT_OCM, 27, 1) + FIELD(CPU_R5_CTRL, CLKACT_CORE, 26, 1) + FIELD(CPU_R5_CTRL, CLKACT, 25, 1) + FIELD(CPU_R5_CTRL, DIVISOR0, 8, 10) + FIELD(CPU_R5_CTRL, SRCSEL, 0, 3) +REG32(IOU_SWITCH_CTRL, 0x114) + FIELD(IOU_SWITCH_CTRL, CLKACT, 25, 1) + FIELD(IOU_SWITCH_CTRL, DIVISOR0, 8, 10) + FIELD(IOU_SWITCH_CTRL, SRCSEL, 0, 3) +REG32(GEM0_REF_CTRL, 0x118) + FIELD(GEM0_REF_CTRL, CLKACT_RX, 27, 1) + FIELD(GEM0_REF_CTRL, CLKACT_TX, 26, 1) + FIELD(GEM0_REF_CTRL, CLKACT, 25, 1) + FIELD(GEM0_REF_CTRL, DIVISOR0, 8, 10) + FIELD(GEM0_REF_CTRL, SRCSEL, 0, 3) +REG32(GEM1_REF_CTRL, 0x11c) + FIELD(GEM1_REF_CTRL, CLKACT_RX, 27, 1) + FIELD(GEM1_REF_CTRL, CLKACT_TX, 26, 1) + FIELD(GEM1_REF_CTRL, CLKACT, 25, 1) + FIELD(GEM1_REF_CTRL, DIVISOR0, 8, 10) + FIELD(GEM1_REF_CTRL, SRCSEL, 0, 3) +REG32(GEM_TSU_REF_CTRL, 0x120) + FIELD(GEM_TSU_REF_CTRL, CLKACT, 25, 1) + FIELD(GEM_TSU_REF_CTRL, DIVISOR0, 8, 10) + FIELD(GEM_TSU_REF_CTRL, SRCSEL, 0, 3) +REG32(USB0_BUS_REF_CTRL, 0x124) + FIELD(USB0_BUS_REF_CTRL, CLKACT, 25, 1) + FIELD(USB0_BUS_REF_CTRL, DIVISOR0, 8, 10) + FIELD(USB0_BUS_REF_CTRL, SRCSEL, 0, 3) +REG32(UART0_REF_CTRL, 0x128) + FIELD(UART0_REF_CTRL, CLKACT, 25, 1) + FIELD(UART0_REF_CTRL, DIVISOR0, 8, 10) + FIELD(UART0_REF_CTRL, SRCSEL, 0, 3) +REG32(UART1_REF_CTRL, 0x12c) + FIELD(UART1_REF_CTRL, CLKACT, 25, 1) + FIELD(UART1_REF_CTRL, DIVISOR0, 8, 10) + FIELD(UART1_REF_CTRL, SRCSEL, 0, 3) +REG32(SPI0_REF_CTRL, 0x130) + FIELD(SPI0_REF_CTRL, CLKACT, 25, 1) + FIELD(SPI0_REF_CTRL, DIVISOR0, 8, 10) + FIELD(SPI0_REF_CTRL, SRCSEL, 0, 3) +REG32(SPI1_REF_CTRL, 0x134) + FIELD(SPI1_REF_CTRL, CLKACT, 25, 1) + FIELD(SPI1_REF_CTRL, DIVISOR0, 8, 10) + FIELD(SPI1_REF_CTRL, SRCSEL, 0, 3) +REG32(CAN0_REF_CTRL, 0x138) + FIELD(CAN0_REF_CTRL, CLKACT, 25, 1) + FIELD(CAN0_REF_CTRL, DIVISOR0, 8, 10) + FIELD(CAN0_REF_CTRL, SRCSEL, 0, 3) +REG32(CAN1_REF_CTRL, 0x13c) + FIELD(CAN1_REF_CTRL, CLKACT, 25, 1) + FIELD(CAN1_REF_CTRL, DIVISOR0, 8, 10) + FIELD(CAN1_REF_CTRL, SRCSEL, 0, 3) +REG32(I2C0_REF_CTRL, 0x140) + FIELD(I2C0_REF_CTRL, CLKACT, 25, 1) + FIELD(I2C0_REF_CTRL, DIVISOR0, 8, 10) + FIELD(I2C0_REF_CTRL, SRCSEL, 0, 3) +REG32(I2C1_REF_CTRL, 0x144) + FIELD(I2C1_REF_CTRL, CLKACT, 25, 1) + FIELD(I2C1_REF_CTRL, DIVISOR0, 8, 10) + FIELD(I2C1_REF_CTRL, SRCSEL, 0, 3) +REG32(DBG_LPD_CTRL, 0x148) + FIELD(DBG_LPD_CTRL, CLKACT, 25, 1) + FIELD(DBG_LPD_CTRL, DIVISOR0, 8, 10) + FIELD(DBG_LPD_CTRL, SRCSEL, 0, 3) +REG32(TIMESTAMP_REF_CTRL, 0x14c) + FIELD(TIMESTAMP_REF_CTRL, CLKACT, 25, 1) + FIELD(TIMESTAMP_REF_CTRL, DIVISOR0, 8, 10) + FIELD(TIMESTAMP_REF_CTRL, SRCSEL, 0, 3) +REG32(CRL_SAFETY_CHK, 0x150) +REG32(PSM_REF_CTRL, 0x154) + FIELD(PSM_REF_CTRL, DIVISOR0, 8, 10) + FIELD(PSM_REF_CTRL, SRCSEL, 0, 3) +REG32(DBG_TSTMP_CTRL, 0x158) + FIELD(DBG_TSTMP_CTRL, CLKACT, 25, 1) + FIELD(DBG_TSTMP_CTRL, DIVISOR0, 8, 10) + FIELD(DBG_TSTMP_CTRL, SRCSEL, 0, 3) +REG32(CPM_TOPSW_REF_CTRL, 0x15c) + FIELD(CPM_TOPSW_REF_CTRL, CLKACT, 25, 1) + FIELD(CPM_TOPSW_REF_CTRL, DIVISOR0, 8, 10) + FIELD(CPM_TOPSW_REF_CTRL, SRCSEL, 0, 3) +REG32(USB3_DUAL_REF_CTRL, 0x160) + FIELD(USB3_DUAL_REF_CTRL, CLKACT, 25, 1) + FIELD(USB3_DUAL_REF_CTRL, DIVISOR0, 8, 10) + FIELD(USB3_DUAL_REF_CTRL, SRCSEL, 0, 3) +REG32(RST_CPU_R5, 0x300) + FIELD(RST_CPU_R5, RESET_PGE, 4, 1) + FIELD(RST_CPU_R5, RESET_AMBA, 2, 1) + FIELD(RST_CPU_R5, RESET_CPU1, 1, 1) + FIELD(RST_CPU_R5, RESET_CPU0, 0, 1) +REG32(RST_ADMA, 0x304) + FIELD(RST_ADMA, RESET, 0, 1) +REG32(RST_GEM0, 0x308) + FIELD(RST_GEM0, RESET, 0, 1) +REG32(RST_GEM1, 0x30c) + FIELD(RST_GEM1, RESET, 0, 1) +REG32(RST_SPARE, 0x310) + FIELD(RST_SPARE, RESET, 0, 1) +REG32(RST_USB0, 0x314) + FIELD(RST_USB0, RESET, 0, 1) +REG32(RST_UART0, 0x318) + FIELD(RST_UART0, RESET, 0, 1) +REG32(RST_UART1, 0x31c) + FIELD(RST_UART1, RESET, 0, 1) +REG32(RST_SPI0, 0x320) + FIELD(RST_SPI0, RESET, 0, 1) +REG32(RST_SPI1, 0x324) + FIELD(RST_SPI1, RESET, 0, 1) +REG32(RST_CAN0, 0x328) + FIELD(RST_CAN0, RESET, 0, 1) +REG32(RST_CAN1, 0x32c) + FIELD(RST_CAN1, RESET, 0, 1) +REG32(RST_I2C0, 0x330) + FIELD(RST_I2C0, RESET, 0, 1) +REG32(RST_I2C1, 0x334) + FIELD(RST_I2C1, RESET, 0, 1) +REG32(RST_DBG_LPD, 0x338) + FIELD(RST_DBG_LPD, RPU_DBG1_RESET, 5, 1) + FIELD(RST_DBG_LPD, RPU_DBG0_RESET, 4, 1) + FIELD(RST_DBG_LPD, RESET_HSDP, 1, 1) + FIELD(RST_DBG_LPD, RESET, 0, 1) +REG32(RST_GPIO, 0x33c) + FIELD(RST_GPIO, RESET, 0, 1) +REG32(RST_TTC, 0x344) + FIELD(RST_TTC, TTC3_RESET, 3, 1) + FIELD(RST_TTC, TTC2_RESET, 2, 1) + FIELD(RST_TTC, TTC1_RESET, 1, 1) + FIELD(RST_TTC, TTC0_RESET, 0, 1) +REG32(RST_TIMESTAMP, 0x348) + FIELD(RST_TIMESTAMP, RESET, 0, 1) +REG32(RST_SWDT, 0x34c) + FIELD(RST_SWDT, RESET, 0, 1) +REG32(RST_OCM, 0x350) + FIELD(RST_OCM, RESET, 0, 1) +REG32(RST_IPI, 0x354) + FIELD(RST_IPI, RESET, 0, 1) +REG32(RST_SYSMON, 0x358) + FIELD(RST_SYSMON, SEQ_RST, 1, 1) + FIELD(RST_SYSMON, CFG_RST, 0, 1) +REG32(RST_FPD, 0x360) + FIELD(RST_FPD, SRST, 1, 1) + FIELD(RST_FPD, POR, 0, 1) +REG32(PSM_RST_MODE, 0x370) + FIELD(PSM_RST_MODE, WAKEUP, 2, 1) + FIELD(PSM_RST_MODE, RST_MODE, 0, 2) + +#define CRL_R_MAX (R_PSM_RST_MODE + 1) + +#define RPU_MAX_CPU 2 + +struct XlnxVersalCRL { + SysBusDevice parent_obj; + qemu_irq irq; + + struct { + ARMCPU *cpu_r5[RPU_MAX_CPU]; + DeviceState *adma[8]; + DeviceState *uart[2]; + DeviceState *gem[2]; + DeviceState *usb; + } cfg; + + RegisterInfoArray *reg_array; + uint32_t regs[CRL_R_MAX]; + RegisterInfo regs_info[CRL_R_MAX]; +}; +#endif diff --git a/hw/misc/xlnx-versal-crl.c b/hw/misc/xlnx-versal-crl.c new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/hw/misc/xlnx-versal-crl.c @@ -XXX,XX +XXX,XX @@ +/* + * QEMU model of the Clock-Reset-LPD (CRL). + * + * Copyright (c) 2022 Advanced Micro Devices, Inc. + * SPDX-License-Identifier: GPL-2.0-or-later + * + * Written by Edgar E. Iglesias <edgar.iglesias@amd.com> + */ + +#include "qemu/osdep.h" +#include "qapi/error.h" +#include "qemu/log.h" +#include "qemu/bitops.h" +#include "migration/vmstate.h" +#include "hw/qdev-properties.h" +#include "hw/sysbus.h" +#include "hw/irq.h" +#include "hw/register.h" +#include "hw/resettable.h" + +#include "target/arm/arm-powerctl.h" +#include "hw/misc/xlnx-versal-crl.h" + +#ifndef XLNX_VERSAL_CRL_ERR_DEBUG +#define XLNX_VERSAL_CRL_ERR_DEBUG 0 +#endif + +static void crl_update_irq(XlnxVersalCRL *s) +{ + bool pending = s->regs[R_IR_STATUS] & ~s->regs[R_IR_MASK]; + qemu_set_irq(s->irq, pending); +} + +static void crl_status_postw(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + crl_update_irq(s); +} + +static uint64_t crl_enable_prew(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + uint32_t val = val64; + + s->regs[R_IR_MASK] &= ~val; + crl_update_irq(s); + return 0; +} + +static uint64_t crl_disable_prew(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + uint32_t val = val64; + + s->regs[R_IR_MASK] |= val; + crl_update_irq(s); + return 0; +} + +static void crl_reset_dev(XlnxVersalCRL *s, DeviceState *dev, + bool rst_old, bool rst_new) +{ + device_cold_reset(dev); +} + +static void crl_reset_cpu(XlnxVersalCRL *s, ARMCPU *armcpu, + bool rst_old, bool rst_new) +{ + if (rst_new) { + arm_set_cpu_off(armcpu->mp_affinity); + } else { + arm_set_cpu_on_and_reset(armcpu->mp_affinity); + } +} + +#define REGFIELD_RESET(type, s, reg, f, new_val, dev) { \ + bool old_f = ARRAY_FIELD_EX32((s)->regs, reg, f); \ + bool new_f = FIELD_EX32(new_val, reg, f); \ + \ + /* Detect edges. */ \ + if (dev && old_f != new_f) { \ + crl_reset_ ## type(s, dev, old_f, new_f); \ + } \ +} + +static uint64_t crl_rst_r5_prew(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + + REGFIELD_RESET(cpu, s, RST_CPU_R5, RESET_CPU0, val64, s->cfg.cpu_r5[0]); + REGFIELD_RESET(cpu, s, RST_CPU_R5, RESET_CPU1, val64, s->cfg.cpu_r5[1]); + return val64; +} + +static uint64_t crl_rst_adma_prew(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + int i; + + /* A single register fans out to all ADMA reset inputs. */ + for (i = 0; i < ARRAY_SIZE(s->cfg.adma); i++) { + REGFIELD_RESET(dev, s, RST_ADMA, RESET, val64, s->cfg.adma[i]); + } + return val64; +} + +static uint64_t crl_rst_uart0_prew(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + + REGFIELD_RESET(dev, s, RST_UART0, RESET, val64, s->cfg.uart[0]); + return val64; +} + +static uint64_t crl_rst_uart1_prew(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + + REGFIELD_RESET(dev, s, RST_UART1, RESET, val64, s->cfg.uart[1]); + return val64; +} + +static uint64_t crl_rst_gem0_prew(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + + REGFIELD_RESET(dev, s, RST_GEM0, RESET, val64, s->cfg.gem[0]); + return val64; +} + +static uint64_t crl_rst_gem1_prew(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + + REGFIELD_RESET(dev, s, RST_GEM1, RESET, val64, s->cfg.gem[1]); + return val64; +} + +static uint64_t crl_rst_usb_prew(RegisterInfo *reg, uint64_t val64) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(reg->opaque); + + REGFIELD_RESET(dev, s, RST_USB0, RESET, val64, s->cfg.usb); + return val64; +} + +static const RegisterAccessInfo crl_regs_info[] = { + { .name = "ERR_CTRL", .addr = A_ERR_CTRL, + },{ .name = "IR_STATUS", .addr = A_IR_STATUS, + .w1c = 0x1, + .post_write = crl_status_postw, + },{ .name = "IR_MASK", .addr = A_IR_MASK, + .reset = 0x1, + .ro = 0x1, + },{ .name = "IR_ENABLE", .addr = A_IR_ENABLE, + .pre_write = crl_enable_prew, + },{ .name = "IR_DISABLE", .addr = A_IR_DISABLE, + .pre_write = crl_disable_prew, + },{ .name = "WPROT", .addr = A_WPROT, + },{ .name = "PLL_CLK_OTHER_DMN", .addr = A_PLL_CLK_OTHER_DMN, + .reset = 0x1, + .rsvd = 0xe, + },{ .name = "RPLL_CTRL", .addr = A_RPLL_CTRL, + .reset = 0x24809, + .rsvd = 0xf88c00f6, + },{ .name = "RPLL_CFG", .addr = A_RPLL_CFG, + .reset = 0x2000000, + .rsvd = 0x1801210, + },{ .name = "RPLL_FRAC_CFG", .addr = A_RPLL_FRAC_CFG, + .rsvd = 0x7e330000, + },{ .name = "PLL_STATUS", .addr = A_PLL_STATUS, + .reset = R_PLL_STATUS_RPLL_STABLE_MASK | + R_PLL_STATUS_RPLL_LOCK_MASK, + .rsvd = 0xfa, + .ro = 0x5, + },{ .name = "RPLL_TO_XPD_CTRL", .addr = A_RPLL_TO_XPD_CTRL, + .reset = 0x2000100, + .rsvd = 0xfdfc00ff, + },{ .name = "LPD_TOP_SWITCH_CTRL", .addr = A_LPD_TOP_SWITCH_CTRL, + .reset = 0x6000300, + .rsvd = 0xf9fc00f8, + },{ .name = "LPD_LSBUS_CTRL", .addr = A_LPD_LSBUS_CTRL, + .reset = 0x2000800, + .rsvd = 0xfdfc00f8, + },{ .name = "CPU_R5_CTRL", .addr = A_CPU_R5_CTRL, + .reset = 0xe000300, + .rsvd = 0xe1fc00f8, + },{ .name = "IOU_SWITCH_CTRL", .addr = A_IOU_SWITCH_CTRL, + .reset = 0x2000500, + .rsvd = 0xfdfc00f8, + },{ .name = "GEM0_REF_CTRL", .addr = A_GEM0_REF_CTRL, + .reset = 0xe000a00, + .rsvd = 0xf1fc00f8, + },{ .name = "GEM1_REF_CTRL", .addr = A_GEM1_REF_CTRL, + .reset = 0xe000a00, + .rsvd = 0xf1fc00f8, + },{ .name = "GEM_TSU_REF_CTRL", .addr = A_GEM_TSU_REF_CTRL, + .reset = 0x300, + .rsvd = 0xfdfc00f8, + },{ .name = "USB0_BUS_REF_CTRL", .addr = A_USB0_BUS_REF_CTRL, + .reset = 0x2001900, + .rsvd = 0xfdfc00f8, + },{ .name = "UART0_REF_CTRL", .addr = A_UART0_REF_CTRL, + .reset = 0xc00, + .rsvd = 0xfdfc00f8, + },{ .name = "UART1_REF_CTRL", .addr = A_UART1_REF_CTRL, + .reset = 0xc00, + .rsvd = 0xfdfc00f8, + },{ .name = "SPI0_REF_CTRL", .addr = A_SPI0_REF_CTRL, + .reset = 0x600, + .rsvd = 0xfdfc00f8, + },{ .name = "SPI1_REF_CTRL", .addr = A_SPI1_REF_CTRL, + .reset = 0x600, + .rsvd = 0xfdfc00f8, + },{ .name = "CAN0_REF_CTRL", .addr = A_CAN0_REF_CTRL, + .reset = 0xc00, + .rsvd = 0xfdfc00f8, + },{ .name = "CAN1_REF_CTRL", .addr = A_CAN1_REF_CTRL, + .reset = 0xc00, + .rsvd = 0xfdfc00f8, + },{ .name = "I2C0_REF_CTRL", .addr = A_I2C0_REF_CTRL, + .reset = 0xc00, + .rsvd = 0xfdfc00f8, + },{ .name = "I2C1_REF_CTRL", .addr = A_I2C1_REF_CTRL, + .reset = 0xc00, + .rsvd = 0xfdfc00f8, + },{ .name = "DBG_LPD_CTRL", .addr = A_DBG_LPD_CTRL, + .reset = 0x300, + .rsvd = 0xfdfc00f8, + },{ .name = "TIMESTAMP_REF_CTRL", .addr = A_TIMESTAMP_REF_CTRL, + .reset = 0x2000c00, + .rsvd = 0xfdfc00f8, + },{ .name = "CRL_SAFETY_CHK", .addr = A_CRL_SAFETY_CHK, + },{ .name = "PSM_REF_CTRL", .addr = A_PSM_REF_CTRL, + .reset = 0xf04, + .rsvd = 0xfffc00f8, + },{ .name = "DBG_TSTMP_CTRL", .addr = A_DBG_TSTMP_CTRL, + .reset = 0x300, + .rsvd = 0xfdfc00f8, + },{ .name = "CPM_TOPSW_REF_CTRL", .addr = A_CPM_TOPSW_REF_CTRL, + .reset = 0x300, + .rsvd = 0xfdfc00f8, + },{ .name = "USB3_DUAL_REF_CTRL", .addr = A_USB3_DUAL_REF_CTRL, + .reset = 0x3c00, + .rsvd = 0xfdfc00f8, + },{ .name = "RST_CPU_R5", .addr = A_RST_CPU_R5, + .reset = 0x17, + .rsvd = 0x8, + .pre_write = crl_rst_r5_prew, + },{ .name = "RST_ADMA", .addr = A_RST_ADMA, + .reset = 0x1, + .pre_write = crl_rst_adma_prew, + },{ .name = "RST_GEM0", .addr = A_RST_GEM0, + .reset = 0x1, + .pre_write = crl_rst_gem0_prew, + },{ .name = "RST_GEM1", .addr = A_RST_GEM1, + .reset = 0x1, + .pre_write = crl_rst_gem1_prew, + },{ .name = "RST_SPARE", .addr = A_RST_SPARE, + .reset = 0x1, + },{ .name = "RST_USB0", .addr = A_RST_USB0, + .reset = 0x1, + .pre_write = crl_rst_usb_prew, + },{ .name = "RST_UART0", .addr = A_RST_UART0, + .reset = 0x1, + .pre_write = crl_rst_uart0_prew, + },{ .name = "RST_UART1", .addr = A_RST_UART1, + .reset = 0x1, + .pre_write = crl_rst_uart1_prew, + },{ .name = "RST_SPI0", .addr = A_RST_SPI0, + .reset = 0x1, + },{ .name = "RST_SPI1", .addr = A_RST_SPI1, + .reset = 0x1, + },{ .name = "RST_CAN0", .addr = A_RST_CAN0, + .reset = 0x1, + },{ .name = "RST_CAN1", .addr = A_RST_CAN1, + .reset = 0x1, + },{ .name = "RST_I2C0", .addr = A_RST_I2C0, + .reset = 0x1, + },{ .name = "RST_I2C1", .addr = A_RST_I2C1, + .reset = 0x1, + },{ .name = "RST_DBG_LPD", .addr = A_RST_DBG_LPD, + .reset = 0x33, + .rsvd = 0xcc, + },{ .name = "RST_GPIO", .addr = A_RST_GPIO, + .reset = 0x1, + },{ .name = "RST_TTC", .addr = A_RST_TTC, + .reset = 0xf, + },{ .name = "RST_TIMESTAMP", .addr = A_RST_TIMESTAMP, + .reset = 0x1, + },{ .name = "RST_SWDT", .addr = A_RST_SWDT, + .reset = 0x1, + },{ .name = "RST_OCM", .addr = A_RST_OCM, + },{ .name = "RST_IPI", .addr = A_RST_IPI, + },{ .name = "RST_FPD", .addr = A_RST_FPD, + .reset = 0x3, + },{ .name = "PSM_RST_MODE", .addr = A_PSM_RST_MODE, + .reset = 0x1, + .rsvd = 0xf8, + } +}; + +static void crl_reset_enter(Object *obj, ResetType type) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(obj); + unsigned int i; + + for (i = 0; i < ARRAY_SIZE(s->regs_info); ++i) { + register_reset(&s->regs_info[i]); + } +} + +static void crl_reset_hold(Object *obj) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(obj); + + crl_update_irq(s); +} + +static const MemoryRegionOps crl_ops = { + .read = register_read_memory, + .write = register_write_memory, + .endianness = DEVICE_LITTLE_ENDIAN, + .valid = { + .min_access_size = 4, + .max_access_size = 4, + }, +}; + +static void crl_init(Object *obj) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(obj); + SysBusDevice *sbd = SYS_BUS_DEVICE(obj); + int i; + + s->reg_array = + register_init_block32(DEVICE(obj), crl_regs_info, + ARRAY_SIZE(crl_regs_info), + s->regs_info, s->regs, + &crl_ops, + XLNX_VERSAL_CRL_ERR_DEBUG, + CRL_R_MAX * 4); + sysbus_init_mmio(sbd, &s->reg_array->mem); + sysbus_init_irq(sbd, &s->irq); + + for (i = 0; i < ARRAY_SIZE(s->cfg.cpu_r5); ++i) { + object_property_add_link(obj, "cpu_r5[*]", TYPE_ARM_CPU, + (Object **)&s->cfg.cpu_r5[i], + qdev_prop_allow_set_link_before_realize, + OBJ_PROP_LINK_STRONG); + } + + for (i = 0; i < ARRAY_SIZE(s->cfg.adma); ++i) { + object_property_add_link(obj, "adma[*]", TYPE_DEVICE, + (Object **)&s->cfg.adma[i], + qdev_prop_allow_set_link_before_realize, + OBJ_PROP_LINK_STRONG); + } + + for (i = 0; i < ARRAY_SIZE(s->cfg.uart); ++i) { + object_property_add_link(obj, "uart[*]", TYPE_DEVICE, + (Object **)&s->cfg.uart[i], + qdev_prop_allow_set_link_before_realize, + OBJ_PROP_LINK_STRONG); + } + + for (i = 0; i < ARRAY_SIZE(s->cfg.gem); ++i) { + object_property_add_link(obj, "gem[*]", TYPE_DEVICE, + (Object **)&s->cfg.gem[i], + qdev_prop_allow_set_link_before_realize, + OBJ_PROP_LINK_STRONG); + } + + object_property_add_link(obj, "usb", TYPE_DEVICE, + (Object **)&s->cfg.gem[i], + qdev_prop_allow_set_link_before_realize, + OBJ_PROP_LINK_STRONG); +} + +static void crl_finalize(Object *obj) +{ + XlnxVersalCRL *s = XLNX_VERSAL_CRL(obj); + register_finalize_block(s->reg_array); +} + +static const VMStateDescription vmstate_crl = { + .name = TYPE_XLNX_VERSAL_CRL, + .version_id = 1, + .minimum_version_id = 1, + .fields = (VMStateField[]) { + VMSTATE_UINT32_ARRAY(regs, XlnxVersalCRL, CRL_R_MAX), + VMSTATE_END_OF_LIST(), + } +}; + +static void crl_class_init(ObjectClass *klass, void *data) +{ + ResettableClass *rc = RESETTABLE_CLASS(klass); + DeviceClass *dc = DEVICE_CLASS(klass); + + dc->vmsd = &vmstate_crl; + + rc->phases.enter = crl_reset_enter; + rc->phases.hold = crl_reset_hold; +} + +static const TypeInfo crl_info = { + .name = TYPE_XLNX_VERSAL_CRL, + .parent = TYPE_SYS_BUS_DEVICE, + .instance_size = sizeof(XlnxVersalCRL), + .class_init = crl_class_init, + .instance_init = crl_init, + .instance_finalize = crl_finalize, +}; + +static void crl_register_types(void) +{ + type_register_static(&crl_info); +} + +type_init(crl_register_types) diff --git a/hw/misc/meson.build b/hw/misc/meson.build index XXXXXXX..XXXXXXX 100644 --- a/hw/misc/meson.build +++ b/hw/misc/meson.build @@ -XXX,XX +XXX,XX @@ softmmu_ss.add(when: 'CONFIG_SLAVIO', if_true: files('slavio_misc.c')) softmmu_ss.add(when: 'CONFIG_ZYNQ', if_true: files('zynq_slcr.c')) specific_ss.add(when: 'CONFIG_XLNX_ZYNQMP_ARM', if_true: files('xlnx-zynqmp-crf.c')) specific_ss.add(when: 'CONFIG_XLNX_ZYNQMP_ARM', if_true: files('xlnx-zynqmp-apu-ctrl.c')) +specific_ss.add(when: 'CONFIG_XLNX_VERSAL', if_true: files('xlnx-versal-crl.c')) softmmu_ss.add(when: 'CONFIG_XLNX_VERSAL', if_true: files( 'xlnx-versal-xramc.c', 'xlnx-versal-pmc-iou-slcr.c', -- 2.25.1 From: "Edgar E. Iglesias" <edgar.iglesias@amd.com> Connect the CRL (Clock Reset LPD) to the Versal SoC. Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com> Reviewed-by: Frederic Konrad <fkonrad@amd.com> Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com> Message-id: 20220406174303.2022038-5-edgar.iglesias@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- include/hw/arm/xlnx-versal.h | 4 +++ hw/arm/xlnx-versal.c | 54 ++++++++++++++++++++++++++++++++++-- 2 files changed, 56 insertions(+), 2 deletions(-) diff --git a/include/hw/arm/xlnx-versal.h b/include/hw/arm/xlnx-versal.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/xlnx-versal.h +++ b/include/hw/arm/xlnx-versal.h @@ -XXX,XX +XXX,XX @@ #include "hw/nvram/xlnx-versal-efuse.h" #include "hw/ssi/xlnx-versal-ospi.h" #include "hw/dma/xlnx_csu_dma.h" +#include "hw/misc/xlnx-versal-crl.h" #include "hw/misc/xlnx-versal-pmc-iou-slcr.h" #define TYPE_XLNX_VERSAL "xlnx-versal" @@ -XXX,XX +XXX,XX @@ struct Versal { qemu_or_irq irq_orgate; XlnxXramCtrl ctrl[XLNX_VERSAL_NR_XRAM]; } xram; + + XlnxVersalCRL crl; } lpd; /* The Platform Management Controller subsystem. */ @@ -XXX,XX +XXX,XX @@ struct Versal { #define VERSAL_TIMER_NS_EL1_IRQ 14 #define VERSAL_TIMER_NS_EL2_IRQ 10 +#define VERSAL_CRL_IRQ 10 #define VERSAL_UART0_IRQ_0 18 #define VERSAL_UART1_IRQ_0 19 #define VERSAL_USB0_IRQ_0 22 diff --git a/hw/arm/xlnx-versal.c b/hw/arm/xlnx-versal.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/xlnx-versal.c +++ b/hw/arm/xlnx-versal.c @@ -XXX,XX +XXX,XX @@ static void versal_create_ospi(Versal *s, qemu_irq *pic) qdev_connect_gpio_out(orgate, 0, pic[VERSAL_OSPI_IRQ]); } +static void versal_create_crl(Versal *s, qemu_irq *pic) +{ + SysBusDevice *sbd; + int i; + + object_initialize_child(OBJECT(s), "crl", &s->lpd.crl, + TYPE_XLNX_VERSAL_CRL); + sbd = SYS_BUS_DEVICE(&s->lpd.crl); + + for (i = 0; i < ARRAY_SIZE(s->lpd.rpu.cpu); i++) { + g_autofree gchar *name = g_strdup_printf("cpu_r5[%d]", i); + + object_property_set_link(OBJECT(&s->lpd.crl), + name, OBJECT(&s->lpd.rpu.cpu[i]), + &error_abort); + } + + for (i = 0; i < ARRAY_SIZE(s->lpd.iou.gem); i++) { + g_autofree gchar *name = g_strdup_printf("gem[%d]", i); + + object_property_set_link(OBJECT(&s->lpd.crl), + name, OBJECT(&s->lpd.iou.gem[i]), + &error_abort); + } + + for (i = 0; i < ARRAY_SIZE(s->lpd.iou.adma); i++) { + g_autofree gchar *name = g_strdup_printf("adma[%d]", i); + + object_property_set_link(OBJECT(&s->lpd.crl), + name, OBJECT(&s->lpd.iou.adma[i]), + &error_abort); + } + + for (i = 0; i < ARRAY_SIZE(s->lpd.iou.uart); i++) { + g_autofree gchar *name = g_strdup_printf("uart[%d]", i); + + object_property_set_link(OBJECT(&s->lpd.crl), + name, OBJECT(&s->lpd.iou.uart[i]), + &error_abort); + } + + object_property_set_link(OBJECT(&s->lpd.crl), + "usb", OBJECT(&s->lpd.iou.usb), + &error_abort); + + sysbus_realize(sbd, &error_fatal); + memory_region_add_subregion(&s->mr_ps, MM_CRL, + sysbus_mmio_get_region(sbd, 0)); + sysbus_connect_irq(sbd, 0, pic[VERSAL_CRL_IRQ]); +} + /* This takes the board allocated linear DDR memory and creates aliases * for each split DDR range/aperture on the Versal address map. */ @@ -XXX,XX +XXX,XX @@ static void versal_unimp(Versal *s) versal_unimp_area(s, "psm", &s->mr_ps, MM_PSM_START, MM_PSM_END - MM_PSM_START); - versal_unimp_area(s, "crl", &s->mr_ps, - MM_CRL, MM_CRL_SIZE); versal_unimp_area(s, "crf", &s->mr_ps, MM_FPD_CRF, MM_FPD_CRF_SIZE); versal_unimp_area(s, "apu", &s->mr_ps, @@ -XXX,XX +XXX,XX @@ static void versal_realize(DeviceState *dev, Error **errp) versal_create_efuse(s, pic); versal_create_pmc_iou_slcr(s, pic); versal_create_ospi(s, pic); + versal_create_crl(s, pic); versal_map_ddr(s); versal_unimp(s); -- 2.25.1 The Exynos4210 SoC device currently uses a custom device "exynos4210.irq_gate" to model the OR gate that feeds each CPU's IRQ line. We have a standard TYPE_OR_IRQ device for this now, so use that instead. (This is a migration compatibility break, but that is OK for this machine type.) Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-2-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 1 + hw/arm/exynos4210.c | 31 ++++++++++++++++--------------- 2 files changed, 17 insertions(+), 15 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ struct Exynos4210State { MemoryRegion bootreg_mem; I2CBus *i2c_if[EXYNOS4210_I2C_NUMBER]; qemu_or_irq pl330_irq_orgate[EXYNOS4210_NUM_DMA]; + qemu_or_irq cpu_irq_orgate[EXYNOS4210_NCPUS]; }; #define TYPE_EXYNOS4210_SOC "exynos4210" diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) { Exynos4210State *s = EXYNOS4210_SOC(socdev); MemoryRegion *system_mem = get_system_memory(); - qemu_irq gate_irq[EXYNOS4210_NCPUS][EXYNOS4210_IRQ_GATE_NINPUTS]; SysBusDevice *busdev; DeviceState *dev, *uart[4], *pl330[3]; int i, n; @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) /* IRQ Gate */ for (i = 0; i < EXYNOS4210_NCPUS; i++) { - dev = qdev_new("exynos4210.irq_gate"); - qdev_prop_set_uint32(dev, "n_in", EXYNOS4210_IRQ_GATE_NINPUTS); - sysbus_realize_and_unref(SYS_BUS_DEVICE(dev), &error_fatal); - /* Get IRQ Gate input in gate_irq */ - for (n = 0; n < EXYNOS4210_IRQ_GATE_NINPUTS; n++) { - gate_irq[i][n] = qdev_get_gpio_in(dev, n); - } - busdev = SYS_BUS_DEVICE(dev); - - /* Connect IRQ Gate output to CPU's IRQ line */ - sysbus_connect_irq(busdev, 0, - qdev_get_gpio_in(DEVICE(s->cpu[i]), ARM_CPU_IRQ)); + DeviceState *orgate = DEVICE(&s->cpu_irq_orgate[i]); + object_property_set_int(OBJECT(orgate), "num-lines", + EXYNOS4210_IRQ_GATE_NINPUTS, + &error_abort); + qdev_realize(orgate, NULL, &error_abort); + qdev_connect_gpio_out(orgate, 0, + qdev_get_gpio_in(DEVICE(s->cpu[i]), ARM_CPU_IRQ)); } /* Private memory region and Internal GIC */ @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) sysbus_realize_and_unref(busdev, &error_fatal); sysbus_mmio_map(busdev, 0, EXYNOS4210_SMP_PRIVATE_BASE_ADDR); for (n = 0; n < EXYNOS4210_NCPUS; n++) { - sysbus_connect_irq(busdev, n, gate_irq[n][0]); + sysbus_connect_irq(busdev, n, + qdev_get_gpio_in(DEVICE(&s->cpu_irq_orgate[n]), 0)); } for (n = 0; n < EXYNOS4210_INT_GIC_NIRQ; n++) { s->irqs.int_gic_irq[n] = qdev_get_gpio_in(dev, n); @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) /* Map Distributer interface */ sysbus_mmio_map(busdev, 1, EXYNOS4210_EXT_GIC_DIST_BASE_ADDR); for (n = 0; n < EXYNOS4210_NCPUS; n++) { - sysbus_connect_irq(busdev, n, gate_irq[n][1]); + sysbus_connect_irq(busdev, n, + qdev_get_gpio_in(DEVICE(&s->cpu_irq_orgate[n]), 1)); } for (n = 0; n < EXYNOS4210_EXT_GIC_NIRQ; n++) { s->irqs.ext_gic_irq[n] = qdev_get_gpio_in(dev, n); @@ -XXX,XX +XXX,XX @@ static void exynos4210_init(Object *obj) object_initialize_child(obj, name, orgate, TYPE_OR_IRQ); g_free(name); } + + for (i = 0; i < ARRAY_SIZE(s->cpu_irq_orgate); i++) { + g_autofree char *name = g_strdup_printf("cpu-irq-orgate%d", i); + object_initialize_child(obj, name, &s->cpu_irq_orgate[i], TYPE_OR_IRQ); + } } static void exynos4210_class_init(ObjectClass *klass, void *data) -- 2.25.1 Now we have removed the only use of TYPE_EXYNOS4210_IRQ_GATE we can delete the device entirely. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com> Message-id: 20220404154658.565020-3-peter.maydell@linaro.org --- hw/intc/exynos4210_gic.c | 107 --------------------------------------- 1 file changed, 107 deletions(-) diff --git a/hw/intc/exynos4210_gic.c b/hw/intc/exynos4210_gic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/exynos4210_gic.c +++ b/hw/intc/exynos4210_gic.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_gic_register_types(void) } type_init(exynos4210_gic_register_types) - -/* IRQ OR Gate struct. - * - * This device models an OR gate. There are n_in input qdev gpio lines and one - * output sysbus IRQ line. The output IRQ level is formed as OR between all - * gpio inputs. - */ - -#define TYPE_EXYNOS4210_IRQ_GATE "exynos4210.irq_gate" -OBJECT_DECLARE_SIMPLE_TYPE(Exynos4210IRQGateState, EXYNOS4210_IRQ_GATE) - -struct Exynos4210IRQGateState { - SysBusDevice parent_obj; - - uint32_t n_in; /* inputs amount */ - uint32_t *level; /* input levels */ - qemu_irq out; /* output IRQ */ -}; - -static Property exynos4210_irq_gate_properties[] = { - DEFINE_PROP_UINT32("n_in", Exynos4210IRQGateState, n_in, 1), - DEFINE_PROP_END_OF_LIST(), -}; - -static const VMStateDescription vmstate_exynos4210_irq_gate = { - .name = "exynos4210.irq_gate", - .version_id = 2, - .minimum_version_id = 2, - .fields = (VMStateField[]) { - VMSTATE_VBUFFER_UINT32(level, Exynos4210IRQGateState, 1, NULL, n_in), - VMSTATE_END_OF_LIST() - } -}; - -/* Process a change in IRQ input. */ -static void exynos4210_irq_gate_handler(void *opaque, int irq, int level) -{ - Exynos4210IRQGateState *s = (Exynos4210IRQGateState *)opaque; - uint32_t i; - - assert(irq < s->n_in); - - s->level[irq] = level; - - for (i = 0; i < s->n_in; i++) { - if (s->level[i] >= 1) { - qemu_irq_raise(s->out); - return; - } - } - - qemu_irq_lower(s->out); -} - -static void exynos4210_irq_gate_reset(DeviceState *d) -{ - Exynos4210IRQGateState *s = EXYNOS4210_IRQ_GATE(d); - - memset(s->level, 0, s->n_in * sizeof(*s->level)); -} - -/* - * IRQ Gate initialization. - */ -static void exynos4210_irq_gate_init(Object *obj) -{ - Exynos4210IRQGateState *s = EXYNOS4210_IRQ_GATE(obj); - SysBusDevice *sbd = SYS_BUS_DEVICE(obj); - - sysbus_init_irq(sbd, &s->out); -} - -static void exynos4210_irq_gate_realize(DeviceState *dev, Error **errp) -{ - Exynos4210IRQGateState *s = EXYNOS4210_IRQ_GATE(dev); - - /* Allocate general purpose input signals and connect a handler to each of - * them */ - qdev_init_gpio_in(dev, exynos4210_irq_gate_handler, s->n_in); - - s->level = g_malloc0(s->n_in * sizeof(*s->level)); -} - -static void exynos4210_irq_gate_class_init(ObjectClass *klass, void *data) -{ - DeviceClass *dc = DEVICE_CLASS(klass); - - dc->reset = exynos4210_irq_gate_reset; - dc->vmsd = &vmstate_exynos4210_irq_gate; - device_class_set_props(dc, exynos4210_irq_gate_properties); - dc->realize = exynos4210_irq_gate_realize; -} - -static const TypeInfo exynos4210_irq_gate_info = { - .name = TYPE_EXYNOS4210_IRQ_GATE, - .parent = TYPE_SYS_BUS_DEVICE, - .instance_size = sizeof(Exynos4210IRQGateState), - .instance_init = exynos4210_irq_gate_init, - .class_init = exynos4210_irq_gate_class_init, -}; - -static void exynos4210_irq_gate_register_types(void) -{ - type_register_static(&exynos4210_irq_gate_info); -} - -type_init(exynos4210_irq_gate_register_types) -- 2.25.1 The exynos4210 SoC mostly creates its child devices as if it were board code. This includes the a9mpcore object. Switch that to a new-style "embedded in the state struct" creation, because in the next commit we're going to want to refer to the object again further down in the exynos4210_realize() function. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-4-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 2 ++ hw/arm/exynos4210.c | 11 ++++++----- 2 files changed, 8 insertions(+), 5 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ #include "hw/or-irq.h" #include "hw/sysbus.h" +#include "hw/cpu/a9mpcore.h" #include "target/arm/cpu-qom.h" #include "qom/object.h" @@ -XXX,XX +XXX,XX @@ struct Exynos4210State { I2CBus *i2c_if[EXYNOS4210_I2C_NUMBER]; qemu_or_irq pl330_irq_orgate[EXYNOS4210_NUM_DMA]; qemu_or_irq cpu_irq_orgate[EXYNOS4210_NCPUS]; + A9MPPrivState a9mpcore; }; #define TYPE_EXYNOS4210_SOC "exynos4210" diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) } /* Private memory region and Internal GIC */ - dev = qdev_new(TYPE_A9MPCORE_PRIV); - qdev_prop_set_uint32(dev, "num-cpu", EXYNOS4210_NCPUS); - busdev = SYS_BUS_DEVICE(dev); - sysbus_realize_and_unref(busdev, &error_fatal); + qdev_prop_set_uint32(DEVICE(&s->a9mpcore), "num-cpu", EXYNOS4210_NCPUS); + busdev = SYS_BUS_DEVICE(&s->a9mpcore); + sysbus_realize(busdev, &error_fatal); sysbus_mmio_map(busdev, 0, EXYNOS4210_SMP_PRIVATE_BASE_ADDR); for (n = 0; n < EXYNOS4210_NCPUS; n++) { sysbus_connect_irq(busdev, n, qdev_get_gpio_in(DEVICE(&s->cpu_irq_orgate[n]), 0)); } for (n = 0; n < EXYNOS4210_INT_GIC_NIRQ; n++) { - s->irqs.int_gic_irq[n] = qdev_get_gpio_in(dev, n); + s->irqs.int_gic_irq[n] = qdev_get_gpio_in(DEVICE(&s->a9mpcore), n); } /* Cache controller */ @@ -XXX,XX +XXX,XX @@ static void exynos4210_init(Object *obj) g_autofree char *name = g_strdup_printf("cpu-irq-orgate%d", i); object_initialize_child(obj, name, &s->cpu_irq_orgate[i], TYPE_OR_IRQ); } + + object_initialize_child(obj, "a9mpcore", &s->a9mpcore, TYPE_A9MPCORE_PRIV); } static void exynos4210_class_init(ObjectClass *klass, void *data) -- 2.25.1 The only time we use the int_gic_irq[] array in the Exynos4210Irq struct is in the exynos4210_realize() function: we initialize it with the GPIO inputs of the a9mpcore device, and then a bit later on we connect those to the outputs of the internal combiner. Now that the a9mpcore object is easily accessible as s->a9mpcore we can make the connection directly from one device to the other without going via this array. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-5-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 1 - hw/arm/exynos4210.c | 6 ++---- 2 files changed, 2 insertions(+), 5 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ typedef struct Exynos4210Irq { qemu_irq int_combiner_irq[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; qemu_irq ext_combiner_irq[EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ]; - qemu_irq int_gic_irq[EXYNOS4210_INT_GIC_NIRQ]; qemu_irq ext_gic_irq[EXYNOS4210_EXT_GIC_NIRQ]; qemu_irq board_irqs[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; } Exynos4210Irq; diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) sysbus_connect_irq(busdev, n, qdev_get_gpio_in(DEVICE(&s->cpu_irq_orgate[n]), 0)); } - for (n = 0; n < EXYNOS4210_INT_GIC_NIRQ; n++) { - s->irqs.int_gic_irq[n] = qdev_get_gpio_in(DEVICE(&s->a9mpcore), n); - } /* Cache controller */ sysbus_create_simple("l2x0", EXYNOS4210_L2X0_BASE_ADDR, NULL); @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) busdev = SYS_BUS_DEVICE(dev); sysbus_realize_and_unref(busdev, &error_fatal); for (n = 0; n < EXYNOS4210_MAX_INT_COMBINER_OUT_IRQ; n++) { - sysbus_connect_irq(busdev, n, s->irqs.int_gic_irq[n]); + sysbus_connect_irq(busdev, n, + qdev_get_gpio_in(DEVICE(&s->a9mpcore), n)); } exynos4210_combiner_get_gpioin(&s->irqs, dev, 0); sysbus_mmio_map(busdev, 0, EXYNOS4210_INT_COMBINER_BASE_ADDR); -- 2.25.1 The exynos4210 code currently has two very similar arrays of IRQs: * board_irqs is a field of the Exynos4210Irq struct which is filled in by exynos4210_init_board_irqs() with the appropriate qemu_irqs for each IRQ the board/SoC can assert * irq_table is a set of qemu_irqs pointed to from the Exynos4210State struct. It's allocated in exynos4210_init_irq, and the only behaviour these irqs have is that they pass on the level to the equivalent board_irqs[] irq The extra indirection through irq_table is unnecessary, so coalesce these into a single irq_table[] array as a direct field in Exynos4210State which exynos4210_init_board_irqs() fills in. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-6-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 8 ++------ hw/arm/exynos4210.c | 6 +----- hw/intc/exynos4210_gic.c | 32 ++++++++------------------------ 3 files changed, 11 insertions(+), 35 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ typedef struct Exynos4210Irq { qemu_irq int_combiner_irq[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; qemu_irq ext_combiner_irq[EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ]; qemu_irq ext_gic_irq[EXYNOS4210_EXT_GIC_NIRQ]; - qemu_irq board_irqs[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; } Exynos4210Irq; struct Exynos4210State { @@ -XXX,XX +XXX,XX @@ struct Exynos4210State { /*< public >*/ ARMCPU *cpu[EXYNOS4210_NCPUS]; Exynos4210Irq irqs; - qemu_irq *irq_table; + qemu_irq irq_table[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; MemoryRegion chipid_mem; MemoryRegion iram_mem; @@ -XXX,XX +XXX,XX @@ OBJECT_DECLARE_SIMPLE_TYPE(Exynos4210State, EXYNOS4210_SOC) void exynos4210_write_secondary(ARMCPU *cpu, const struct arm_boot_info *info); -/* Initialize exynos4210 IRQ subsystem stub */ -qemu_irq *exynos4210_init_irq(Exynos4210Irq *env); - /* Initialize board IRQs. * These IRQs contain splitted Int/External Combiner and External Gic IRQs */ -void exynos4210_init_board_irqs(Exynos4210Irq *s); +void exynos4210_init_board_irqs(Exynos4210State *s); /* Get IRQ number from exynos4210 IRQ subsystem stub. * To identify IRQ source use internal combiner group and bit number diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) qdev_realize(DEVICE(cpuobj), NULL, &error_fatal); } - /*** IRQs ***/ - - s->irq_table = exynos4210_init_irq(&s->irqs); - /* IRQ Gate */ for (i = 0; i < EXYNOS4210_NCPUS; i++) { DeviceState *orgate = DEVICE(&s->cpu_irq_orgate[i]); @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) sysbus_mmio_map(busdev, 0, EXYNOS4210_EXT_COMBINER_BASE_ADDR); /* Initialize board IRQs. */ - exynos4210_init_board_irqs(&s->irqs); + exynos4210_init_board_irqs(s); /*** Memory ***/ diff --git a/hw/intc/exynos4210_gic.c b/hw/intc/exynos4210_gic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/exynos4210_gic.c +++ b/hw/intc/exynos4210_gic.c @@ -XXX,XX +XXX,XX @@ combiner_grp_to_gic_id[64-EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { #define EXYNOS4210_GIC_CPU_REGION_SIZE 0x100 #define EXYNOS4210_GIC_DIST_REGION_SIZE 0x1000 -static void exynos4210_irq_handler(void *opaque, int irq, int level) -{ - Exynos4210Irq *s = (Exynos4210Irq *)opaque; - - /* Bypass */ - qemu_set_irq(s->board_irqs[irq], level); -} - -/* - * Initialize exynos4210 IRQ subsystem stub. - */ -qemu_irq *exynos4210_init_irq(Exynos4210Irq *s) -{ - return qemu_allocate_irqs(exynos4210_irq_handler, s, - EXYNOS4210_MAX_INT_COMBINER_IN_IRQ); -} - /* * Initialize board IRQs. * These IRQs contain splitted Int/External Combiner and External Gic IRQs. */ -void exynos4210_init_board_irqs(Exynos4210Irq *s) +void exynos4210_init_board_irqs(Exynos4210State *s) { uint32_t grp, bit, irq_id, n; + Exynos4210Irq *is = &s->irqs; for (n = 0; n < EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ; n++) { irq_id = 0; @@ -XXX,XX +XXX,XX @@ void exynos4210_init_board_irqs(Exynos4210Irq *s) irq_id = EXT_GIC_ID_MCT_G1; } if (irq_id) { - s->board_irqs[n] = qemu_irq_split(s->int_combiner_irq[n], - s->ext_gic_irq[irq_id-32]); + s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], + is->ext_gic_irq[irq_id - 32]); } else { - s->board_irqs[n] = qemu_irq_split(s->int_combiner_irq[n], - s->ext_combiner_irq[n]); + s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], + is->ext_combiner_irq[n]); } } for (; n < EXYNOS4210_MAX_INT_COMBINER_IN_IRQ; n++) { @@ -XXX,XX +XXX,XX @@ void exynos4210_init_board_irqs(Exynos4210Irq *s) EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][bit]; if (irq_id) { - s->board_irqs[n] = qemu_irq_split(s->int_combiner_irq[n], - s->ext_gic_irq[irq_id-32]); + s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], + is->ext_gic_irq[irq_id - 32]); } } } -- 2.25.1 Fix a missing set of spaces around '-' in the definition of combiner_grp_to_gic_id[]. We're about to move this code, so fix the style issue first to keep checkpatch happy with the code-motion patch. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-7-peter.maydell@linaro.org --- hw/intc/exynos4210_gic.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/hw/intc/exynos4210_gic.c b/hw/intc/exynos4210_gic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/exynos4210_gic.c +++ b/hw/intc/exynos4210_gic.c @@ -XXX,XX +XXX,XX @@ enum ExtInt { */ static const uint32_t -combiner_grp_to_gic_id[64-EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { +combiner_grp_to_gic_id[64 - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { /* int combiner groups 16-19 */ { }, { }, { }, { }, /* int combiner group 20 */ -- 2.25.1 The function exynos4210_init_board_irqs() currently lives in exynos4210_gic.c, but it isn't really part of the exynos4210.gic device -- it is a function that implements (some of) the wiring up of interrupts between the SoC's GIC and combiner components. This means it fits better in exynos4210.c, which is the SoC-level code. Move it there. Similarly, exynos4210_git_irq() is used almost only in the SoC-level code, so move it too. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-8-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 4 - hw/arm/exynos4210.c | 202 +++++++++++++++++++++++++++++++++++ hw/intc/exynos4210_gic.c | 204 ------------------------------------ 3 files changed, 202 insertions(+), 208 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ OBJECT_DECLARE_SIMPLE_TYPE(Exynos4210State, EXYNOS4210_SOC) void exynos4210_write_secondary(ARMCPU *cpu, const struct arm_boot_info *info); -/* Initialize board IRQs. - * These IRQs contain splitted Int/External Combiner and External Gic IRQs */ -void exynos4210_init_board_irqs(Exynos4210State *s); - /* Get IRQ number from exynos4210 IRQ subsystem stub. * To identify IRQ source use internal combiner group and bit number * grp - group number diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ #define EXYNOS4210_PL330_BASE1_ADDR 0x12690000 #define EXYNOS4210_PL330_BASE2_ADDR 0x12850000 +enum ExtGicId { + EXT_GIC_ID_MDMA_LCD0 = 66, + EXT_GIC_ID_PDMA0, + EXT_GIC_ID_PDMA1, + EXT_GIC_ID_TIMER0, + EXT_GIC_ID_TIMER1, + EXT_GIC_ID_TIMER2, + EXT_GIC_ID_TIMER3, + EXT_GIC_ID_TIMER4, + EXT_GIC_ID_MCT_L0, + EXT_GIC_ID_WDT, + EXT_GIC_ID_RTC_ALARM, + EXT_GIC_ID_RTC_TIC, + EXT_GIC_ID_GPIO_XB, + EXT_GIC_ID_GPIO_XA, + EXT_GIC_ID_MCT_L1, + EXT_GIC_ID_IEM_APC, + EXT_GIC_ID_IEM_IEC, + EXT_GIC_ID_NFC, + EXT_GIC_ID_UART0, + EXT_GIC_ID_UART1, + EXT_GIC_ID_UART2, + EXT_GIC_ID_UART3, + EXT_GIC_ID_UART4, + EXT_GIC_ID_MCT_G0, + EXT_GIC_ID_I2C0, + EXT_GIC_ID_I2C1, + EXT_GIC_ID_I2C2, + EXT_GIC_ID_I2C3, + EXT_GIC_ID_I2C4, + EXT_GIC_ID_I2C5, + EXT_GIC_ID_I2C6, + EXT_GIC_ID_I2C7, + EXT_GIC_ID_SPI0, + EXT_GIC_ID_SPI1, + EXT_GIC_ID_SPI2, + EXT_GIC_ID_MCT_G1, + EXT_GIC_ID_USB_HOST, + EXT_GIC_ID_USB_DEVICE, + EXT_GIC_ID_MODEMIF, + EXT_GIC_ID_HSMMC0, + EXT_GIC_ID_HSMMC1, + EXT_GIC_ID_HSMMC2, + EXT_GIC_ID_HSMMC3, + EXT_GIC_ID_SDMMC, + EXT_GIC_ID_MIPI_CSI_4LANE, + EXT_GIC_ID_MIPI_DSI_4LANE, + EXT_GIC_ID_MIPI_CSI_2LANE, + EXT_GIC_ID_MIPI_DSI_2LANE, + EXT_GIC_ID_ONENAND_AUDI, + EXT_GIC_ID_ROTATOR, + EXT_GIC_ID_FIMC0, + EXT_GIC_ID_FIMC1, + EXT_GIC_ID_FIMC2, + EXT_GIC_ID_FIMC3, + EXT_GIC_ID_JPEG, + EXT_GIC_ID_2D, + EXT_GIC_ID_PCIe, + EXT_GIC_ID_MIXER, + EXT_GIC_ID_HDMI, + EXT_GIC_ID_HDMI_I2C, + EXT_GIC_ID_MFC, + EXT_GIC_ID_TVENC, +}; + +enum ExtInt { + EXT_GIC_ID_EXTINT0 = 48, + EXT_GIC_ID_EXTINT1, + EXT_GIC_ID_EXTINT2, + EXT_GIC_ID_EXTINT3, + EXT_GIC_ID_EXTINT4, + EXT_GIC_ID_EXTINT5, + EXT_GIC_ID_EXTINT6, + EXT_GIC_ID_EXTINT7, + EXT_GIC_ID_EXTINT8, + EXT_GIC_ID_EXTINT9, + EXT_GIC_ID_EXTINT10, + EXT_GIC_ID_EXTINT11, + EXT_GIC_ID_EXTINT12, + EXT_GIC_ID_EXTINT13, + EXT_GIC_ID_EXTINT14, + EXT_GIC_ID_EXTINT15 +}; + +/* + * External GIC sources which are not from External Interrupt Combiner or + * External Interrupts are starting from EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ, + * which is INTG16 in Internal Interrupt Combiner. + */ + +static const uint32_t +combiner_grp_to_gic_id[64 - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { + /* int combiner groups 16-19 */ + { }, { }, { }, { }, + /* int combiner group 20 */ + { 0, EXT_GIC_ID_MDMA_LCD0 }, + /* int combiner group 21 */ + { EXT_GIC_ID_PDMA0, EXT_GIC_ID_PDMA1 }, + /* int combiner group 22 */ + { EXT_GIC_ID_TIMER0, EXT_GIC_ID_TIMER1, EXT_GIC_ID_TIMER2, + EXT_GIC_ID_TIMER3, EXT_GIC_ID_TIMER4 }, + /* int combiner group 23 */ + { EXT_GIC_ID_RTC_ALARM, EXT_GIC_ID_RTC_TIC }, + /* int combiner group 24 */ + { EXT_GIC_ID_GPIO_XB, EXT_GIC_ID_GPIO_XA }, + /* int combiner group 25 */ + { EXT_GIC_ID_IEM_APC, EXT_GIC_ID_IEM_IEC }, + /* int combiner group 26 */ + { EXT_GIC_ID_UART0, EXT_GIC_ID_UART1, EXT_GIC_ID_UART2, EXT_GIC_ID_UART3, + EXT_GIC_ID_UART4 }, + /* int combiner group 27 */ + { EXT_GIC_ID_I2C0, EXT_GIC_ID_I2C1, EXT_GIC_ID_I2C2, EXT_GIC_ID_I2C3, + EXT_GIC_ID_I2C4, EXT_GIC_ID_I2C5, EXT_GIC_ID_I2C6, + EXT_GIC_ID_I2C7 }, + /* int combiner group 28 */ + { EXT_GIC_ID_SPI0, EXT_GIC_ID_SPI1, EXT_GIC_ID_SPI2 , EXT_GIC_ID_USB_HOST}, + /* int combiner group 29 */ + { EXT_GIC_ID_HSMMC0, EXT_GIC_ID_HSMMC1, EXT_GIC_ID_HSMMC2, + EXT_GIC_ID_HSMMC3, EXT_GIC_ID_SDMMC }, + /* int combiner group 30 */ + { EXT_GIC_ID_MIPI_CSI_4LANE, EXT_GIC_ID_MIPI_CSI_2LANE }, + /* int combiner group 31 */ + { EXT_GIC_ID_MIPI_DSI_4LANE, EXT_GIC_ID_MIPI_DSI_2LANE }, + /* int combiner group 32 */ + { EXT_GIC_ID_FIMC0, EXT_GIC_ID_FIMC1 }, + /* int combiner group 33 */ + { EXT_GIC_ID_FIMC2, EXT_GIC_ID_FIMC3 }, + /* int combiner group 34 */ + { EXT_GIC_ID_ONENAND_AUDI, EXT_GIC_ID_NFC }, + /* int combiner group 35 */ + { 0, 0, 0, EXT_GIC_ID_MCT_L1, EXT_GIC_ID_MCT_G0, EXT_GIC_ID_MCT_G1 }, + /* int combiner group 36 */ + { EXT_GIC_ID_MIXER }, + /* int combiner group 37 */ + { EXT_GIC_ID_EXTINT4, EXT_GIC_ID_EXTINT5, EXT_GIC_ID_EXTINT6, + EXT_GIC_ID_EXTINT7 }, + /* groups 38-50 */ + { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, + /* int combiner group 51 */ + { EXT_GIC_ID_MCT_L0, 0, 0, 0, EXT_GIC_ID_MCT_G0, EXT_GIC_ID_MCT_G1 }, + /* group 52 */ + { }, + /* int combiner group 53 */ + { EXT_GIC_ID_WDT, 0, 0, 0, EXT_GIC_ID_MCT_G0, EXT_GIC_ID_MCT_G1 }, + /* groups 54-63 */ + { }, { }, { }, { }, { }, { }, { }, { }, { }, { } +}; + +/* + * Initialize board IRQs. + * These IRQs contain splitted Int/External Combiner and External Gic IRQs. + */ +static void exynos4210_init_board_irqs(Exynos4210State *s) +{ + uint32_t grp, bit, irq_id, n; + Exynos4210Irq *is = &s->irqs; + + for (n = 0; n < EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ; n++) { + irq_id = 0; + if (n == EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 4) || + n == EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 4)) { + /* MCT_G0 is passed to External GIC */ + irq_id = EXT_GIC_ID_MCT_G0; + } + if (n == EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 5) || + n == EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 5)) { + /* MCT_G1 is passed to External and GIC */ + irq_id = EXT_GIC_ID_MCT_G1; + } + if (irq_id) { + s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], + is->ext_gic_irq[irq_id - 32]); + } else { + s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], + is->ext_combiner_irq[n]); + } + } + for (; n < EXYNOS4210_MAX_INT_COMBINER_IN_IRQ; n++) { + /* these IDs are passed to Internal Combiner and External GIC */ + grp = EXYNOS4210_COMBINER_GET_GRP_NUM(n); + bit = EXYNOS4210_COMBINER_GET_BIT_NUM(n); + irq_id = combiner_grp_to_gic_id[grp - + EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][bit]; + + if (irq_id) { + s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], + is->ext_gic_irq[irq_id - 32]); + } + } +} + +/* + * Get IRQ number from exynos4210 IRQ subsystem stub. + * To identify IRQ source use internal combiner group and bit number + * grp - group number + * bit - bit number inside group + */ +uint32_t exynos4210_get_irq(uint32_t grp, uint32_t bit) +{ + return EXYNOS4210_COMBINER_GET_IRQ_NUM(grp, bit); +} + static uint8_t chipid_and_omr[] = { 0x11, 0x02, 0x21, 0x43, 0x09, 0x00, 0x00, 0x00 }; diff --git a/hw/intc/exynos4210_gic.c b/hw/intc/exynos4210_gic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/exynos4210_gic.c +++ b/hw/intc/exynos4210_gic.c @@ -XXX,XX +XXX,XX @@ #include "hw/arm/exynos4210.h" #include "qom/object.h" -enum ExtGicId { - EXT_GIC_ID_MDMA_LCD0 = 66, - EXT_GIC_ID_PDMA0, - EXT_GIC_ID_PDMA1, - EXT_GIC_ID_TIMER0, - EXT_GIC_ID_TIMER1, - EXT_GIC_ID_TIMER2, - EXT_GIC_ID_TIMER3, - EXT_GIC_ID_TIMER4, - EXT_GIC_ID_MCT_L0, - EXT_GIC_ID_WDT, - EXT_GIC_ID_RTC_ALARM, - EXT_GIC_ID_RTC_TIC, - EXT_GIC_ID_GPIO_XB, - EXT_GIC_ID_GPIO_XA, - EXT_GIC_ID_MCT_L1, - EXT_GIC_ID_IEM_APC, - EXT_GIC_ID_IEM_IEC, - EXT_GIC_ID_NFC, - EXT_GIC_ID_UART0, - EXT_GIC_ID_UART1, - EXT_GIC_ID_UART2, - EXT_GIC_ID_UART3, - EXT_GIC_ID_UART4, - EXT_GIC_ID_MCT_G0, - EXT_GIC_ID_I2C0, - EXT_GIC_ID_I2C1, - EXT_GIC_ID_I2C2, - EXT_GIC_ID_I2C3, - EXT_GIC_ID_I2C4, - EXT_GIC_ID_I2C5, - EXT_GIC_ID_I2C6, - EXT_GIC_ID_I2C7, - EXT_GIC_ID_SPI0, - EXT_GIC_ID_SPI1, - EXT_GIC_ID_SPI2, - EXT_GIC_ID_MCT_G1, - EXT_GIC_ID_USB_HOST, - EXT_GIC_ID_USB_DEVICE, - EXT_GIC_ID_MODEMIF, - EXT_GIC_ID_HSMMC0, - EXT_GIC_ID_HSMMC1, - EXT_GIC_ID_HSMMC2, - EXT_GIC_ID_HSMMC3, - EXT_GIC_ID_SDMMC, - EXT_GIC_ID_MIPI_CSI_4LANE, - EXT_GIC_ID_MIPI_DSI_4LANE, - EXT_GIC_ID_MIPI_CSI_2LANE, - EXT_GIC_ID_MIPI_DSI_2LANE, - EXT_GIC_ID_ONENAND_AUDI, - EXT_GIC_ID_ROTATOR, - EXT_GIC_ID_FIMC0, - EXT_GIC_ID_FIMC1, - EXT_GIC_ID_FIMC2, - EXT_GIC_ID_FIMC3, - EXT_GIC_ID_JPEG, - EXT_GIC_ID_2D, - EXT_GIC_ID_PCIe, - EXT_GIC_ID_MIXER, - EXT_GIC_ID_HDMI, - EXT_GIC_ID_HDMI_I2C, - EXT_GIC_ID_MFC, - EXT_GIC_ID_TVENC, -}; - -enum ExtInt { - EXT_GIC_ID_EXTINT0 = 48, - EXT_GIC_ID_EXTINT1, - EXT_GIC_ID_EXTINT2, - EXT_GIC_ID_EXTINT3, - EXT_GIC_ID_EXTINT4, - EXT_GIC_ID_EXTINT5, - EXT_GIC_ID_EXTINT6, - EXT_GIC_ID_EXTINT7, - EXT_GIC_ID_EXTINT8, - EXT_GIC_ID_EXTINT9, - EXT_GIC_ID_EXTINT10, - EXT_GIC_ID_EXTINT11, - EXT_GIC_ID_EXTINT12, - EXT_GIC_ID_EXTINT13, - EXT_GIC_ID_EXTINT14, - EXT_GIC_ID_EXTINT15 -}; - -/* - * External GIC sources which are not from External Interrupt Combiner or - * External Interrupts are starting from EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ, - * which is INTG16 in Internal Interrupt Combiner. - */ - -static const uint32_t -combiner_grp_to_gic_id[64 - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { - /* int combiner groups 16-19 */ - { }, { }, { }, { }, - /* int combiner group 20 */ - { 0, EXT_GIC_ID_MDMA_LCD0 }, - /* int combiner group 21 */ - { EXT_GIC_ID_PDMA0, EXT_GIC_ID_PDMA1 }, - /* int combiner group 22 */ - { EXT_GIC_ID_TIMER0, EXT_GIC_ID_TIMER1, EXT_GIC_ID_TIMER2, - EXT_GIC_ID_TIMER3, EXT_GIC_ID_TIMER4 }, - /* int combiner group 23 */ - { EXT_GIC_ID_RTC_ALARM, EXT_GIC_ID_RTC_TIC }, - /* int combiner group 24 */ - { EXT_GIC_ID_GPIO_XB, EXT_GIC_ID_GPIO_XA }, - /* int combiner group 25 */ - { EXT_GIC_ID_IEM_APC, EXT_GIC_ID_IEM_IEC }, - /* int combiner group 26 */ - { EXT_GIC_ID_UART0, EXT_GIC_ID_UART1, EXT_GIC_ID_UART2, EXT_GIC_ID_UART3, - EXT_GIC_ID_UART4 }, - /* int combiner group 27 */ - { EXT_GIC_ID_I2C0, EXT_GIC_ID_I2C1, EXT_GIC_ID_I2C2, EXT_GIC_ID_I2C3, - EXT_GIC_ID_I2C4, EXT_GIC_ID_I2C5, EXT_GIC_ID_I2C6, - EXT_GIC_ID_I2C7 }, - /* int combiner group 28 */ - { EXT_GIC_ID_SPI0, EXT_GIC_ID_SPI1, EXT_GIC_ID_SPI2 , EXT_GIC_ID_USB_HOST}, - /* int combiner group 29 */ - { EXT_GIC_ID_HSMMC0, EXT_GIC_ID_HSMMC1, EXT_GIC_ID_HSMMC2, - EXT_GIC_ID_HSMMC3, EXT_GIC_ID_SDMMC }, - /* int combiner group 30 */ - { EXT_GIC_ID_MIPI_CSI_4LANE, EXT_GIC_ID_MIPI_CSI_2LANE }, - /* int combiner group 31 */ - { EXT_GIC_ID_MIPI_DSI_4LANE, EXT_GIC_ID_MIPI_DSI_2LANE }, - /* int combiner group 32 */ - { EXT_GIC_ID_FIMC0, EXT_GIC_ID_FIMC1 }, - /* int combiner group 33 */ - { EXT_GIC_ID_FIMC2, EXT_GIC_ID_FIMC3 }, - /* int combiner group 34 */ - { EXT_GIC_ID_ONENAND_AUDI, EXT_GIC_ID_NFC }, - /* int combiner group 35 */ - { 0, 0, 0, EXT_GIC_ID_MCT_L1, EXT_GIC_ID_MCT_G0, EXT_GIC_ID_MCT_G1 }, - /* int combiner group 36 */ - { EXT_GIC_ID_MIXER }, - /* int combiner group 37 */ - { EXT_GIC_ID_EXTINT4, EXT_GIC_ID_EXTINT5, EXT_GIC_ID_EXTINT6, - EXT_GIC_ID_EXTINT7 }, - /* groups 38-50 */ - { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, - /* int combiner group 51 */ - { EXT_GIC_ID_MCT_L0, 0, 0, 0, EXT_GIC_ID_MCT_G0, EXT_GIC_ID_MCT_G1 }, - /* group 52 */ - { }, - /* int combiner group 53 */ - { EXT_GIC_ID_WDT, 0, 0, 0, EXT_GIC_ID_MCT_G0, EXT_GIC_ID_MCT_G1 }, - /* groups 54-63 */ - { }, { }, { }, { }, { }, { }, { }, { }, { }, { } -}; - #define EXYNOS4210_GIC_NIRQ 160 #define EXYNOS4210_EXT_GIC_CPU_REGION_SIZE 0x10000 @@ -XXX,XX +XXX,XX @@ combiner_grp_to_gic_id[64 - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { #define EXYNOS4210_GIC_CPU_REGION_SIZE 0x100 #define EXYNOS4210_GIC_DIST_REGION_SIZE 0x1000 -/* - * Initialize board IRQs. - * These IRQs contain splitted Int/External Combiner and External Gic IRQs. - */ -void exynos4210_init_board_irqs(Exynos4210State *s) -{ - uint32_t grp, bit, irq_id, n; - Exynos4210Irq *is = &s->irqs; - - for (n = 0; n < EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ; n++) { - irq_id = 0; - if (n == EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 4) || - n == EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 4)) { - /* MCT_G0 is passed to External GIC */ - irq_id = EXT_GIC_ID_MCT_G0; - } - if (n == EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 5) || - n == EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 5)) { - /* MCT_G1 is passed to External and GIC */ - irq_id = EXT_GIC_ID_MCT_G1; - } - if (irq_id) { - s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], - is->ext_gic_irq[irq_id - 32]); - } else { - s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], - is->ext_combiner_irq[n]); - } - } - for (; n < EXYNOS4210_MAX_INT_COMBINER_IN_IRQ; n++) { - /* these IDs are passed to Internal Combiner and External GIC */ - grp = EXYNOS4210_COMBINER_GET_GRP_NUM(n); - bit = EXYNOS4210_COMBINER_GET_BIT_NUM(n); - irq_id = combiner_grp_to_gic_id[grp - - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][bit]; - - if (irq_id) { - s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], - is->ext_gic_irq[irq_id - 32]); - } - } -} - -/* - * Get IRQ number from exynos4210 IRQ subsystem stub. - * To identify IRQ source use internal combiner group and bit number - * grp - group number - * bit - bit number inside group - */ -uint32_t exynos4210_get_irq(uint32_t grp, uint32_t bit) -{ - return EXYNOS4210_COMBINER_GET_IRQ_NUM(grp, bit); -} - -/********* GIC part *********/ - #define TYPE_EXYNOS4210_GIC "exynos4210.gic" OBJECT_DECLARE_SIMPLE_TYPE(Exynos4210GicState, EXYNOS4210_GIC) -- 2.25.1 Switch the creation of the external GIC to the new-style "embedded in state struct" approach, so we can easily refer to the object elsewhere during realize. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-9-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 2 ++ include/hw/intc/exynos4210_gic.h | 43 ++++++++++++++++++++++++++++++++ hw/arm/exynos4210.c | 10 ++++---- hw/intc/exynos4210_gic.c | 17 ++----------- MAINTAINERS | 2 +- 5 files changed, 53 insertions(+), 21 deletions(-) create mode 100644 include/hw/intc/exynos4210_gic.h diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ #include "hw/or-irq.h" #include "hw/sysbus.h" #include "hw/cpu/a9mpcore.h" +#include "hw/intc/exynos4210_gic.h" #include "target/arm/cpu-qom.h" #include "qom/object.h" @@ -XXX,XX +XXX,XX @@ struct Exynos4210State { qemu_or_irq pl330_irq_orgate[EXYNOS4210_NUM_DMA]; qemu_or_irq cpu_irq_orgate[EXYNOS4210_NCPUS]; A9MPPrivState a9mpcore; + Exynos4210GicState ext_gic; }; #define TYPE_EXYNOS4210_SOC "exynos4210" diff --git a/include/hw/intc/exynos4210_gic.h b/include/hw/intc/exynos4210_gic.h new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/include/hw/intc/exynos4210_gic.h @@ -XXX,XX +XXX,XX @@ +/* + * Samsung exynos4210 GIC implementation. Based on hw/arm_gic.c + * + * Copyright (c) 2000 - 2011 Samsung Electronics Co., Ltd. + * All rights reserved. + * + * Evgeny Voevodin <e.voevodin@samsung.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + * See the GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, see <http://www.gnu.org/licenses/>. + */ +#ifndef HW_INTC_EXYNOS4210_GIC_H +#define HW_INTC_EXYNOS4210_GIC_H + +#include "hw/sysbus.h" + +#define TYPE_EXYNOS4210_GIC "exynos4210.gic" +OBJECT_DECLARE_SIMPLE_TYPE(Exynos4210GicState, EXYNOS4210_GIC) + +#define EXYNOS4210_GIC_NCPUS 2 + +struct Exynos4210GicState { + SysBusDevice parent_obj; + + MemoryRegion cpu_container; + MemoryRegion dist_container; + MemoryRegion cpu_alias[EXYNOS4210_GIC_NCPUS]; + MemoryRegion dist_alias[EXYNOS4210_GIC_NCPUS]; + uint32_t num_cpu; + DeviceState *gic; +}; + +#endif diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) sysbus_create_simple("l2x0", EXYNOS4210_L2X0_BASE_ADDR, NULL); /* External GIC */ - dev = qdev_new("exynos4210.gic"); - qdev_prop_set_uint32(dev, "num-cpu", EXYNOS4210_NCPUS); - busdev = SYS_BUS_DEVICE(dev); - sysbus_realize_and_unref(busdev, &error_fatal); + qdev_prop_set_uint32(DEVICE(&s->ext_gic), "num-cpu", EXYNOS4210_NCPUS); + busdev = SYS_BUS_DEVICE(&s->ext_gic); + sysbus_realize(busdev, &error_fatal); /* Map CPU interface */ sysbus_mmio_map(busdev, 0, EXYNOS4210_EXT_GIC_CPU_BASE_ADDR); /* Map Distributer interface */ @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) qdev_get_gpio_in(DEVICE(&s->cpu_irq_orgate[n]), 1)); } for (n = 0; n < EXYNOS4210_EXT_GIC_NIRQ; n++) { - s->irqs.ext_gic_irq[n] = qdev_get_gpio_in(dev, n); + s->irqs.ext_gic_irq[n] = qdev_get_gpio_in(DEVICE(&s->ext_gic), n); } /* Internal Interrupt Combiner */ @@ -XXX,XX +XXX,XX @@ static void exynos4210_init(Object *obj) } object_initialize_child(obj, "a9mpcore", &s->a9mpcore, TYPE_A9MPCORE_PRIV); + object_initialize_child(obj, "ext-gic", &s->ext_gic, TYPE_EXYNOS4210_GIC); } static void exynos4210_class_init(ObjectClass *klass, void *data) diff --git a/hw/intc/exynos4210_gic.c b/hw/intc/exynos4210_gic.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/exynos4210_gic.c +++ b/hw/intc/exynos4210_gic.c @@ -XXX,XX +XXX,XX @@ #include "qemu/module.h" #include "hw/irq.h" #include "hw/qdev-properties.h" +#include "hw/intc/exynos4210_gic.h" #include "hw/arm/exynos4210.h" #include "qom/object.h" @@ -XXX,XX +XXX,XX @@ #define EXYNOS4210_GIC_CPU_REGION_SIZE 0x100 #define EXYNOS4210_GIC_DIST_REGION_SIZE 0x1000 -#define TYPE_EXYNOS4210_GIC "exynos4210.gic" -OBJECT_DECLARE_SIMPLE_TYPE(Exynos4210GicState, EXYNOS4210_GIC) - -struct Exynos4210GicState { - SysBusDevice parent_obj; - - MemoryRegion cpu_container; - MemoryRegion dist_container; - MemoryRegion cpu_alias[EXYNOS4210_NCPUS]; - MemoryRegion dist_alias[EXYNOS4210_NCPUS]; - uint32_t num_cpu; - DeviceState *gic; -}; - static void exynos4210_gic_set_irq(void *opaque, int irq, int level) { Exynos4210GicState *s = (Exynos4210GicState *)opaque; @@ -XXX,XX +XXX,XX @@ static void exynos4210_gic_realize(DeviceState *dev, Error **errp) * enough room for the cpu numbers. gcc 9.2.1 on 32-bit x86 * doesn't figure this out, otherwise and gives spurious warnings. */ - assert(n <= EXYNOS4210_NCPUS); + assert(n <= EXYNOS4210_GIC_NCPUS); for (i = 0; i < n; i++) { /* Map CPU interface per SMP Core */ sprintf(cpu_alias_name, "%s%x", cpu_prefix, i); diff --git a/MAINTAINERS b/MAINTAINERS index XXXXXXX..XXXXXXX 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -XXX,XX +XXX,XX @@ M: Peter Maydell <peter.maydell@linaro.org> L: qemu-arm@nongnu.org S: Odd Fixes F: hw/*/exynos* -F: include/hw/arm/exynos4210.h +F: include/hw/*/exynos* Calxeda Highbank M: Rob Herring <robh@kernel.org> -- 2.25.1 The only time we use the ext_gic_irq[] array in the Exynos4210Irq struct is during realize of the SoC -- we initialize it with the input IRQs of the external GIC device, and then connect those to outputs of other devices further on in realize (including in the exynos4210_init_board_irqs() function). Now that the ext_gic object is easily accessible as s->ext_gic we can make the connections directly from one device to the other without going via this array. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-10-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 1 - hw/arm/exynos4210.c | 12 ++++++------ 2 files changed, 6 insertions(+), 7 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ typedef struct Exynos4210Irq { qemu_irq int_combiner_irq[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; qemu_irq ext_combiner_irq[EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ]; - qemu_irq ext_gic_irq[EXYNOS4210_EXT_GIC_NIRQ]; } Exynos4210Irq; struct Exynos4210State { diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) { uint32_t grp, bit, irq_id, n; Exynos4210Irq *is = &s->irqs; + DeviceState *extgicdev = DEVICE(&s->ext_gic); for (n = 0; n < EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ; n++) { irq_id = 0; @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) } if (irq_id) { s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], - is->ext_gic_irq[irq_id - 32]); + qdev_get_gpio_in(extgicdev, + irq_id - 32)); } else { s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], is->ext_combiner_irq[n]); @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) if (irq_id) { s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], - is->ext_gic_irq[irq_id - 32]); + qdev_get_gpio_in(extgicdev, + irq_id - 32)); } } } @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) sysbus_connect_irq(busdev, n, qdev_get_gpio_in(DEVICE(&s->cpu_irq_orgate[n]), 1)); } - for (n = 0; n < EXYNOS4210_EXT_GIC_NIRQ; n++) { - s->irqs.ext_gic_irq[n] = qdev_get_gpio_in(DEVICE(&s->ext_gic), n); - } /* Internal Interrupt Combiner */ dev = qdev_new("exynos4210.combiner"); @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) busdev = SYS_BUS_DEVICE(dev); sysbus_realize_and_unref(busdev, &error_fatal); for (n = 0; n < EXYNOS4210_MAX_INT_COMBINER_OUT_IRQ; n++) { - sysbus_connect_irq(busdev, n, s->irqs.ext_gic_irq[n]); + sysbus_connect_irq(busdev, n, qdev_get_gpio_in(DEVICE(&s->ext_gic), n)); } exynos4210_combiner_get_gpioin(&s->irqs, dev, 1); sysbus_mmio_map(busdev, 0, EXYNOS4210_EXT_COMBINER_BASE_ADDR); -- 2.25.1 The function exynos4210_combiner_get_gpioin() currently lives in exynos4210_combiner.c, but it isn't really part of the combiner device itself -- it is a function that implements the wiring up of some interrupt sources to multiple combiner inputs. Move it to live with the other SoC-level code in exynos4210.c, along with a few macros previously defined in exynos4210.h which are now used only in exynos4210.c. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-11-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 11 ----- hw/arm/exynos4210.c | 82 +++++++++++++++++++++++++++++++++++ hw/intc/exynos4210_combiner.c | 77 -------------------------------- 3 files changed, 82 insertions(+), 88 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ #define EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ \ (EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ * 8) -#define EXYNOS4210_COMBINER_GET_IRQ_NUM(grp, bit) ((grp)*8 + (bit)) -#define EXYNOS4210_COMBINER_GET_GRP_NUM(irq) ((irq) / 8) -#define EXYNOS4210_COMBINER_GET_BIT_NUM(irq) \ - ((irq) - 8 * EXYNOS4210_COMBINER_GET_GRP_NUM(irq)) - /* IRQs number for external and internal GIC */ #define EXYNOS4210_EXT_GIC_NIRQ (160-32) #define EXYNOS4210_INT_GIC_NIRQ 64 @@ -XXX,XX +XXX,XX @@ void exynos4210_write_secondary(ARMCPU *cpu, * bit - bit number inside group */ uint32_t exynos4210_get_irq(uint32_t grp, uint32_t bit); -/* - * Get Combiner input GPIO into irqs structure - */ -void exynos4210_combiner_get_gpioin(Exynos4210Irq *irqs, DeviceState *dev, - int ext); - /* * exynos4210 UART */ diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ combiner_grp_to_gic_id[64 - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { { }, { }, { }, { }, { }, { }, { }, { }, { }, { } }; +#define EXYNOS4210_COMBINER_GET_IRQ_NUM(grp, bit) ((grp) * 8 + (bit)) +#define EXYNOS4210_COMBINER_GET_GRP_NUM(irq) ((irq) / 8) +#define EXYNOS4210_COMBINER_GET_BIT_NUM(irq) \ + ((irq) - 8 * EXYNOS4210_COMBINER_GET_GRP_NUM(irq)) + /* * Initialize board IRQs. * These IRQs contain splitted Int/External Combiner and External Gic IRQs. @@ -XXX,XX +XXX,XX @@ uint32_t exynos4210_get_irq(uint32_t grp, uint32_t bit) return EXYNOS4210_COMBINER_GET_IRQ_NUM(grp, bit); } +/* + * Get Combiner input GPIO into irqs structure + */ +static void exynos4210_combiner_get_gpioin(Exynos4210Irq *irqs, + DeviceState *dev, int ext) +{ + int n; + int bit; + int max; + qemu_irq *irq; + + max = ext ? EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ : + EXYNOS4210_MAX_INT_COMBINER_IN_IRQ; + irq = ext ? irqs->ext_combiner_irq : irqs->int_combiner_irq; + + /* + * Some IRQs of Int/External Combiner are going to two Combiners groups, + * so let split them. + */ + for (n = 0; n < max; n++) { + + bit = EXYNOS4210_COMBINER_GET_BIT_NUM(n); + + switch (n) { + /* MDNIE_LCD1 INTG1 */ + case EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 0) ... + EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 3): + irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), + irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(0, bit + 4)]); + continue; + + /* TMU INTG3 */ + case EXYNOS4210_COMBINER_GET_IRQ_NUM(3, 4): + irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), + irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(2, bit)]); + continue; + + /* LCD1 INTG12 */ + case EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 0) ... + EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 3): + irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), + irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(11, bit + 4)]); + continue; + + /* Multi-Core Timer INTG12 */ + case EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 4) ... + EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 8): + irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), + irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); + continue; + + /* Multi-Core Timer INTG35 */ + case EXYNOS4210_COMBINER_GET_IRQ_NUM(35, 4) ... + EXYNOS4210_COMBINER_GET_IRQ_NUM(35, 8): + irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), + irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); + continue; + + /* Multi-Core Timer INTG51 */ + case EXYNOS4210_COMBINER_GET_IRQ_NUM(51, 4) ... + EXYNOS4210_COMBINER_GET_IRQ_NUM(51, 8): + irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), + irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); + continue; + + /* Multi-Core Timer INTG53 */ + case EXYNOS4210_COMBINER_GET_IRQ_NUM(53, 4) ... + EXYNOS4210_COMBINER_GET_IRQ_NUM(53, 8): + irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), + irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); + continue; + } + + irq[n] = qdev_get_gpio_in(dev, n); + } +} + static uint8_t chipid_and_omr[] = { 0x11, 0x02, 0x21, 0x43, 0x09, 0x00, 0x00, 0x00 }; diff --git a/hw/intc/exynos4210_combiner.c b/hw/intc/exynos4210_combiner.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/exynos4210_combiner.c +++ b/hw/intc/exynos4210_combiner.c @@ -XXX,XX +XXX,XX @@ static const VMStateDescription vmstate_exynos4210_combiner = { } }; -/* - * Get Combiner input GPIO into irqs structure - */ -void exynos4210_combiner_get_gpioin(Exynos4210Irq *irqs, DeviceState *dev, - int ext) -{ - int n; - int bit; - int max; - qemu_irq *irq; - - max = ext ? EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ : - EXYNOS4210_MAX_INT_COMBINER_IN_IRQ; - irq = ext ? irqs->ext_combiner_irq : irqs->int_combiner_irq; - - /* - * Some IRQs of Int/External Combiner are going to two Combiners groups, - * so let split them. - */ - for (n = 0; n < max; n++) { - - bit = EXYNOS4210_COMBINER_GET_BIT_NUM(n); - - switch (n) { - /* MDNIE_LCD1 INTG1 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 0) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 3): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(0, bit + 4)]); - continue; - - /* TMU INTG3 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(3, 4): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(2, bit)]); - continue; - - /* LCD1 INTG12 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 0) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 3): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(11, bit + 4)]); - continue; - - /* Multi-Core Timer INTG12 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 4) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 8): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); - continue; - - /* Multi-Core Timer INTG35 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(35, 4) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(35, 8): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); - continue; - - /* Multi-Core Timer INTG51 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(51, 4) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(51, 8): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); - continue; - - /* Multi-Core Timer INTG53 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(53, 4) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(53, 8): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); - continue; - } - - irq[n] = qdev_get_gpio_in(dev, n); - } -} - static uint64_t exynos4210_combiner_read(void *opaque, hwaddr offset, unsigned size) { -- 2.25.1 Delete a couple of #defines which are never used. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-12-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 4 ---- 1 file changed, 4 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ #define EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ \ (EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ * 8) -/* IRQs number for external and internal GIC */ -#define EXYNOS4210_EXT_GIC_NIRQ (160-32) -#define EXYNOS4210_INT_GIC_NIRQ 64 - #define EXYNOS4210_I2C_NUMBER 9 #define EXYNOS4210_NUM_DMA 3 -- 2.25.1 In exynos4210_init_board_irqs(), use the TYPE_SPLIT_IRQ device instead of qemu_irq_split(). Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-13-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 9 ++++++++ hw/arm/exynos4210.c | 41 +++++++++++++++++++++++++++++-------- 2 files changed, 42 insertions(+), 8 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ #include "hw/sysbus.h" #include "hw/cpu/a9mpcore.h" #include "hw/intc/exynos4210_gic.h" +#include "hw/core/split-irq.h" #include "target/arm/cpu-qom.h" #include "qom/object.h" @@ -XXX,XX +XXX,XX @@ #define EXYNOS4210_NUM_DMA 3 +/* + * We need one splitter for every external combiner input, plus + * one for every non-zero entry in combiner_grp_to_gic_id[]. + * We'll assert in exynos4210_init_board_irqs() if this is wrong. + */ +#define EXYNOS4210_NUM_SPLITTERS (EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ + 60) + typedef struct Exynos4210Irq { qemu_irq int_combiner_irq[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; qemu_irq ext_combiner_irq[EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ]; @@ -XXX,XX +XXX,XX @@ struct Exynos4210State { qemu_or_irq cpu_irq_orgate[EXYNOS4210_NCPUS]; A9MPPrivState a9mpcore; Exynos4210GicState ext_gic; + SplitIRQ splitter[EXYNOS4210_NUM_SPLITTERS]; }; #define TYPE_EXYNOS4210_SOC "exynos4210" diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) uint32_t grp, bit, irq_id, n; Exynos4210Irq *is = &s->irqs; DeviceState *extgicdev = DEVICE(&s->ext_gic); + int splitcount = 0; + DeviceState *splitter; for (n = 0; n < EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ; n++) { irq_id = 0; @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) /* MCT_G1 is passed to External and GIC */ irq_id = EXT_GIC_ID_MCT_G1; } + + assert(splitcount < EXYNOS4210_NUM_SPLITTERS); + splitter = DEVICE(&s->splitter[splitcount]); + qdev_prop_set_uint16(splitter, "num-lines", 2); + qdev_realize(splitter, NULL, &error_abort); + splitcount++; + s->irq_table[n] = qdev_get_gpio_in(splitter, 0); + qdev_connect_gpio_out(splitter, 0, is->int_combiner_irq[n]); if (irq_id) { - s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], - qdev_get_gpio_in(extgicdev, - irq_id - 32)); + qdev_connect_gpio_out(splitter, 1, + qdev_get_gpio_in(extgicdev, irq_id - 32)); } else { - s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], - is->ext_combiner_irq[n]); + qdev_connect_gpio_out(splitter, 1, is->ext_combiner_irq[n]); } } for (; n < EXYNOS4210_MAX_INT_COMBINER_IN_IRQ; n++) { @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][bit]; if (irq_id) { - s->irq_table[n] = qemu_irq_split(is->int_combiner_irq[n], - qdev_get_gpio_in(extgicdev, - irq_id - 32)); + assert(splitcount < EXYNOS4210_NUM_SPLITTERS); + splitter = DEVICE(&s->splitter[splitcount]); + qdev_prop_set_uint16(splitter, "num-lines", 2); + qdev_realize(splitter, NULL, &error_abort); + splitcount++; + s->irq_table[n] = qdev_get_gpio_in(splitter, 0); + qdev_connect_gpio_out(splitter, 0, is->int_combiner_irq[n]); + qdev_connect_gpio_out(splitter, 1, + qdev_get_gpio_in(extgicdev, irq_id - 32)); } } + /* + * We check this here to avoid a more obscure assert later when + * qdev_assert_realized_properly() checks that we realized every + * child object we initialized. + */ + assert(splitcount == EXYNOS4210_NUM_SPLITTERS); } /* @@ -XXX,XX +XXX,XX @@ static void exynos4210_init(Object *obj) object_initialize_child(obj, name, &s->cpu_irq_orgate[i], TYPE_OR_IRQ); } + for (i = 0; i < ARRAY_SIZE(s->splitter); i++) { + g_autofree char *name = g_strdup_printf("irq-splitter%d", i); + object_initialize_child(obj, name, &s->splitter[i], TYPE_SPLIT_IRQ); + } + object_initialize_child(obj, "a9mpcore", &s->a9mpcore, TYPE_A9MPCORE_PRIV); object_initialize_child(obj, "ext-gic", &s->ext_gic, TYPE_EXYNOS4210_GIC); } -- 2.25.1 In exynos4210_init_board_irqs(), the loop that handles IRQ lines that are in a range that applies to the internal combiner only creates a splitter for those interrupts which go to both the internal combiner and to the external GIC, but it does nothing at all for the interrupts which don't go to the external GIC, leaving the irq_table[] array element empty for those. (This will result in those interrupts simply being lost, not in a QEMU crash.) I don't have a reliable datasheet for this SoC, but since we do wire up one interrupt line in this category (the HDMI I2C device on interrupt 16,1), this seems like it must be a bug in the existing QEMU code. Fill in the irq_table[] entries where we're not splitting the IRQ to both the internal combiner and the external GIC with the IRQ line of the internal combiner. (That is, these IRQ lines go to just one device, not multiple.) This bug didn't have any visible guest effects because the only implemented device that was affected was the HDMI I2C controller, and we never connect any I2C devices to that bus. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-14-peter.maydell@linaro.org --- hw/arm/exynos4210.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) qdev_connect_gpio_out(splitter, 0, is->int_combiner_irq[n]); qdev_connect_gpio_out(splitter, 1, qdev_get_gpio_in(extgicdev, irq_id - 32)); + } else { + s->irq_table[n] = is->int_combiner_irq[n]; } } /* -- 2.25.1 Currently for the interrupts MCT_G0 and MCT_G1 which are the only ones in the input range of the external combiner and which are also wired to the external GIC, we connect them only to the internal combiner and the external GIC. This seems likely to be a bug, as all other interrupts which are in the input range of both combiners are connected to both combiners. (The fact that the code in exynos4210_combiner_get_gpioin() is also trying to wire up these inputs on both combiners also suggests this.) Wire these interrupts up to both combiners, like the rest. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-15-peter.maydell@linaro.org --- hw/arm/exynos4210.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) assert(splitcount < EXYNOS4210_NUM_SPLITTERS); splitter = DEVICE(&s->splitter[splitcount]); - qdev_prop_set_uint16(splitter, "num-lines", 2); + qdev_prop_set_uint16(splitter, "num-lines", irq_id ? 3 : 2); qdev_realize(splitter, NULL, &error_abort); splitcount++; s->irq_table[n] = qdev_get_gpio_in(splitter, 0); qdev_connect_gpio_out(splitter, 0, is->int_combiner_irq[n]); + qdev_connect_gpio_out(splitter, 1, is->ext_combiner_irq[n]); if (irq_id) { - qdev_connect_gpio_out(splitter, 1, + qdev_connect_gpio_out(splitter, 2, qdev_get_gpio_in(extgicdev, irq_id - 32)); - } else { - qdev_connect_gpio_out(splitter, 1, is->ext_combiner_irq[n]); } } for (; n < EXYNOS4210_MAX_INT_COMBINER_IN_IRQ; n++) { -- 2.25.1 The combiner_grp_to_gic_id[] array includes the EXT_GIC_ID_MCT_G0 and EXT_GIC_ID_MCT_G1 multiple times. This means that we will connect multiple IRQs up to the same external GIC input, which is not permitted. We do the same thing in the code in exynos4210_init_board_irqs() because the conditionals selecting an irq_id in the first loop match multiple interrupt IDs. Overall we do this for interrupt IDs (1, 4), (12, 4), (35, 4), (51, 4), (53, 4) for EXT_GIC_ID_MCT_G0 and (1, 5), (12, 5), (35, 5), (51, 5), (53, 5) for EXT_GIC_ID_MCT_G1 These correspond to the cases for the multi-core timer that we are wiring up to multiple inputs on the combiner in exynos4210_combiner_get_gpioin(). That code already deals with all these interrupt IDs being the same input source, so we don't need to connect the external GIC interrupt for any of them except the first (1, 4) and (1, 5). Remove the array entries and conditionals which were incorrectly causing us to wire up extra lines. This bug didn't cause any visible effects, because we only connect up a device to the "primary" ID values (1, 4) and (1, 5), so the extra lines would never be set to a level. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-16-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 2 +- hw/arm/exynos4210.c | 12 +++++------- 2 files changed, 6 insertions(+), 8 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ * one for every non-zero entry in combiner_grp_to_gic_id[]. * We'll assert in exynos4210_init_board_irqs() if this is wrong. */ -#define EXYNOS4210_NUM_SPLITTERS (EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ + 60) +#define EXYNOS4210_NUM_SPLITTERS (EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ + 54) typedef struct Exynos4210Irq { qemu_irq int_combiner_irq[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ combiner_grp_to_gic_id[64 - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { /* int combiner group 34 */ { EXT_GIC_ID_ONENAND_AUDI, EXT_GIC_ID_NFC }, /* int combiner group 35 */ - { 0, 0, 0, EXT_GIC_ID_MCT_L1, EXT_GIC_ID_MCT_G0, EXT_GIC_ID_MCT_G1 }, + { 0, 0, 0, EXT_GIC_ID_MCT_L1 }, /* int combiner group 36 */ { EXT_GIC_ID_MIXER }, /* int combiner group 37 */ @@ -XXX,XX +XXX,XX @@ combiner_grp_to_gic_id[64 - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { /* groups 38-50 */ { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, { }, /* int combiner group 51 */ - { EXT_GIC_ID_MCT_L0, 0, 0, 0, EXT_GIC_ID_MCT_G0, EXT_GIC_ID_MCT_G1 }, + { EXT_GIC_ID_MCT_L0 }, /* group 52 */ { }, /* int combiner group 53 */ - { EXT_GIC_ID_WDT, 0, 0, 0, EXT_GIC_ID_MCT_G0, EXT_GIC_ID_MCT_G1 }, + { EXT_GIC_ID_WDT }, /* groups 54-63 */ { }, { }, { }, { }, { }, { }, { }, { }, { }, { } }; @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) for (n = 0; n < EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ; n++) { irq_id = 0; - if (n == EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 4) || - n == EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 4)) { + if (n == EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 4)) { /* MCT_G0 is passed to External GIC */ irq_id = EXT_GIC_ID_MCT_G0; } - if (n == EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 5) || - n == EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 5)) { + if (n == EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 5)) { /* MCT_G1 is passed to External and GIC */ irq_id = EXT_GIC_ID_MCT_G1; } -- 2.25.1 At this point, the function exynos4210_init_board_irqs() splits input IRQ lines to connect them to the input combiner, output combiner and external GIC. The function exynos4210_combiner_get_gpioin() splits some of the combiner input lines further to connect them to multiple different inputs on the combiner. Because (unlike qemu_irq_split()) the TYPE_SPLIT_IRQ device has a configurable number of outputs, we can do all this in one place, by making exynos4210_init_board_irqs() add extra outputs to the splitter device when it must be connected to more than one input on each combiner. We do this with a new data structure, the combinermap, which is an array each of whose elements is a list of the interrupt IDs on the combiner which must be tied together. As we loop through each interrupt ID, if we find that it is the first one in one of these lists, we configure the splitter device with eonugh extra outputs and wire them up to the other interrupt IDs in the list. Conveniently, for all the cases where this is necessary, the lowest-numbered interrupt ID in each group is in the range of the external combiner, so we only need to code for this in the first of the two loops in exynos4210_init_board_irqs(). The old code in exynos4210_combiner_get_gpioin() which is being deleted here had several problems which don't exist in the new code in its handling of the multi-core timer interrupts: (1) the case labels specified bits 4 ... 8, but bit '8' doesn't exist; these should have been 4 ... 7 (2) it used the input irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)] multiple times as the input of several different splitters, which isn't allowed (3) in an apparent cut-and-paste error, the cases for all the multi-core timer inputs used "bit + 4" even though the bit range for the case was (intended to be) 4 ... 7, which meant it was looking at non-existent bits 8 ... 11. None of these exist in the new code. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-17-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 6 +- hw/arm/exynos4210.c | 178 +++++++++++++++++++++++------------- 2 files changed, 119 insertions(+), 65 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ /* * We need one splitter for every external combiner input, plus - * one for every non-zero entry in combiner_grp_to_gic_id[]. + * one for every non-zero entry in combiner_grp_to_gic_id[], + * minus one for every external combiner ID in second or later + * places in a combinermap[] line. * We'll assert in exynos4210_init_board_irqs() if this is wrong. */ -#define EXYNOS4210_NUM_SPLITTERS (EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ + 54) +#define EXYNOS4210_NUM_SPLITTERS (EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ + 38) typedef struct Exynos4210Irq { qemu_irq int_combiner_irq[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ combiner_grp_to_gic_id[64 - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][8] = { #define EXYNOS4210_COMBINER_GET_BIT_NUM(irq) \ ((irq) - 8 * EXYNOS4210_COMBINER_GET_GRP_NUM(irq)) +/* + * Some interrupt lines go to multiple combiner inputs. + * This data structure defines those: each array element is + * a list of combiner inputs which are connected together; + * the one with the smallest interrupt ID value must be first. + * As with combiner_grp_to_gic_id[], we rely on (0, 0) not being + * wired to anything so we can use 0 as a terminator. + */ +#define IRQNO(G, B) EXYNOS4210_COMBINER_GET_IRQ_NUM(G, B) +#define IRQNONE 0 + +#define COMBINERMAP_SIZE 16 + +static const int combinermap[COMBINERMAP_SIZE][6] = { + /* MDNIE_LCD1 */ + { IRQNO(0, 4), IRQNO(1, 0), IRQNONE }, + { IRQNO(0, 5), IRQNO(1, 1), IRQNONE }, + { IRQNO(0, 6), IRQNO(1, 2), IRQNONE }, + { IRQNO(0, 7), IRQNO(1, 3), IRQNONE }, + /* TMU */ + { IRQNO(2, 4), IRQNO(3, 4), IRQNONE }, + { IRQNO(2, 5), IRQNO(3, 5), IRQNONE }, + { IRQNO(2, 6), IRQNO(3, 6), IRQNONE }, + { IRQNO(2, 7), IRQNO(3, 7), IRQNONE }, + /* LCD1 */ + { IRQNO(11, 4), IRQNO(12, 0), IRQNONE }, + { IRQNO(11, 5), IRQNO(12, 1), IRQNONE }, + { IRQNO(11, 6), IRQNO(12, 2), IRQNONE }, + { IRQNO(11, 7), IRQNO(12, 3), IRQNONE }, + /* Multi-core timer */ + { IRQNO(1, 4), IRQNO(12, 4), IRQNO(35, 4), IRQNO(51, 4), IRQNO(53, 4), IRQNONE }, + { IRQNO(1, 5), IRQNO(12, 5), IRQNO(35, 5), IRQNO(51, 5), IRQNO(53, 5), IRQNONE }, + { IRQNO(1, 6), IRQNO(12, 6), IRQNO(35, 6), IRQNO(51, 6), IRQNO(53, 6), IRQNONE }, + { IRQNO(1, 7), IRQNO(12, 7), IRQNO(35, 7), IRQNO(51, 7), IRQNO(53, 7), IRQNONE }, +}; + +#undef IRQNO + +static const int *combinermap_entry(int irq) +{ + /* + * If the interrupt number passed in is the first entry in some + * line of the combinermap, return a pointer to that line; + * otherwise return NULL. + */ + int i; + for (i = 0; i < COMBINERMAP_SIZE; i++) { + if (combinermap[i][0] == irq) { + return combinermap[i]; + } + } + return NULL; +} + +static int mapline_size(const int *mapline) +{ + /* Return number of entries in this mapline in total */ + int i = 0; + + if (!mapline) { + /* Not in the map? IRQ goes to exactly one combiner input */ + return 1; + } + while (*mapline != IRQNONE) { + mapline++; + i++; + } + return i; +} + /* * Initialize board IRQs. * These IRQs contain splitted Int/External Combiner and External Gic IRQs. @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) DeviceState *extgicdev = DEVICE(&s->ext_gic); int splitcount = 0; DeviceState *splitter; + const int *mapline; + int numlines, splitin, in; for (n = 0; n < EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ; n++) { irq_id = 0; @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) irq_id = EXT_GIC_ID_MCT_G1; } + if (s->irq_table[n]) { + /* + * This must be some non-first entry in a combinermap line, + * and we've already filled it in. + */ + continue; + } + mapline = combinermap_entry(n); + /* + * We need to connect the IRQ to multiple inputs on both combiners + * and possibly also to the external GIC. + */ + numlines = 2 * mapline_size(mapline); + if (irq_id) { + numlines++; + } assert(splitcount < EXYNOS4210_NUM_SPLITTERS); splitter = DEVICE(&s->splitter[splitcount]); - qdev_prop_set_uint16(splitter, "num-lines", irq_id ? 3 : 2); + qdev_prop_set_uint16(splitter, "num-lines", numlines); qdev_realize(splitter, NULL, &error_abort); splitcount++; - s->irq_table[n] = qdev_get_gpio_in(splitter, 0); - qdev_connect_gpio_out(splitter, 0, is->int_combiner_irq[n]); - qdev_connect_gpio_out(splitter, 1, is->ext_combiner_irq[n]); + + in = n; + splitin = 0; + for (;;) { + s->irq_table[in] = qdev_get_gpio_in(splitter, 0); + qdev_connect_gpio_out(splitter, splitin, is->int_combiner_irq[in]); + qdev_connect_gpio_out(splitter, splitin + 1, is->ext_combiner_irq[in]); + splitin += 2; + if (!mapline) { + break; + } + mapline++; + in = *mapline; + if (in == IRQNONE) { + break; + } + } if (irq_id) { - qdev_connect_gpio_out(splitter, 2, + qdev_connect_gpio_out(splitter, splitin, qdev_get_gpio_in(extgicdev, irq_id - 32)); } } @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) irq_id = combiner_grp_to_gic_id[grp - EXYNOS4210_MAX_EXT_COMBINER_OUT_IRQ][bit]; + if (s->irq_table[n]) { + /* + * This must be some non-first entry in a combinermap line, + * and we've already filled it in. + */ + continue; + } + if (irq_id) { assert(splitcount < EXYNOS4210_NUM_SPLITTERS); splitter = DEVICE(&s->splitter[splitcount]); @@ -XXX,XX +XXX,XX @@ static void exynos4210_combiner_get_gpioin(Exynos4210Irq *irqs, DeviceState *dev, int ext) { int n; - int bit; int max; qemu_irq *irq; @@ -XXX,XX +XXX,XX @@ static void exynos4210_combiner_get_gpioin(Exynos4210Irq *irqs, EXYNOS4210_MAX_INT_COMBINER_IN_IRQ; irq = ext ? irqs->ext_combiner_irq : irqs->int_combiner_irq; - /* - * Some IRQs of Int/External Combiner are going to two Combiners groups, - * so let split them. - */ for (n = 0; n < max; n++) { - - bit = EXYNOS4210_COMBINER_GET_BIT_NUM(n); - - switch (n) { - /* MDNIE_LCD1 INTG1 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 0) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(1, 3): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(0, bit + 4)]); - continue; - - /* TMU INTG3 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(3, 4): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(2, bit)]); - continue; - - /* LCD1 INTG12 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 0) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 3): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(11, bit + 4)]); - continue; - - /* Multi-Core Timer INTG12 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 4) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(12, 8): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); - continue; - - /* Multi-Core Timer INTG35 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(35, 4) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(35, 8): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); - continue; - - /* Multi-Core Timer INTG51 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(51, 4) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(51, 8): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); - continue; - - /* Multi-Core Timer INTG53 */ - case EXYNOS4210_COMBINER_GET_IRQ_NUM(53, 4) ... - EXYNOS4210_COMBINER_GET_IRQ_NUM(53, 8): - irq[n] = qemu_irq_split(qdev_get_gpio_in(dev, n), - irq[EXYNOS4210_COMBINER_GET_IRQ_NUM(1, bit + 4)]); - continue; - } - irq[n] = qdev_get_gpio_in(dev, n); } } -- 2.25.1 Switch the creation of the combiner devices to the new-style "embedded in state struct" approach, so we can easily refer to the object elsewhere during realize. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-18-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 3 ++ include/hw/intc/exynos4210_combiner.h | 57 +++++++++++++++++++++++++++ hw/arm/exynos4210.c | 20 +++++----- hw/intc/exynos4210_combiner.c | 31 +-------------- 4 files changed, 72 insertions(+), 39 deletions(-) create mode 100644 include/hw/intc/exynos4210_combiner.h diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ #include "hw/sysbus.h" #include "hw/cpu/a9mpcore.h" #include "hw/intc/exynos4210_gic.h" +#include "hw/intc/exynos4210_combiner.h" #include "hw/core/split-irq.h" #include "target/arm/cpu-qom.h" #include "qom/object.h" @@ -XXX,XX +XXX,XX @@ struct Exynos4210State { qemu_or_irq cpu_irq_orgate[EXYNOS4210_NCPUS]; A9MPPrivState a9mpcore; Exynos4210GicState ext_gic; + Exynos4210CombinerState int_combiner; + Exynos4210CombinerState ext_combiner; SplitIRQ splitter[EXYNOS4210_NUM_SPLITTERS]; }; diff --git a/include/hw/intc/exynos4210_combiner.h b/include/hw/intc/exynos4210_combiner.h new file mode 100644 index XXXXXXX..XXXXXXX --- /dev/null +++ b/include/hw/intc/exynos4210_combiner.h @@ -XXX,XX +XXX,XX @@ +/* + * Samsung exynos4210 Interrupt Combiner + * + * Copyright (c) 2000 - 2011 Samsung Electronics Co., Ltd. + * All rights reserved. + * + * Evgeny Voevodin <e.voevodin@samsung.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + * See the GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef HW_INTC_EXYNOS4210_COMBINER +#define HW_INTC_EXYNOS4210_COMBINER + +#include "hw/sysbus.h" + +/* + * State for each output signal of internal combiner + */ +typedef struct CombinerGroupState { + uint8_t src_mask; /* 1 - source enabled, 0 - disabled */ + uint8_t src_pending; /* Pending source interrupts before masking */ +} CombinerGroupState; + +#define TYPE_EXYNOS4210_COMBINER "exynos4210.combiner" +OBJECT_DECLARE_SIMPLE_TYPE(Exynos4210CombinerState, EXYNOS4210_COMBINER) + +/* Number of groups and total number of interrupts for the internal combiner */ +#define IIC_NGRP 64 +#define IIC_NIRQ (IIC_NGRP * 8) +#define IIC_REGSET_SIZE 0x41 + +struct Exynos4210CombinerState { + SysBusDevice parent_obj; + + MemoryRegion iomem; + + struct CombinerGroupState group[IIC_NGRP]; + uint32_t reg_set[IIC_REGSET_SIZE]; + uint32_t icipsr[2]; + uint32_t external; /* 1 means that this combiner is external */ + + qemu_irq output_irq[IIC_NGRP]; +}; + +#endif diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) } /* Internal Interrupt Combiner */ - dev = qdev_new("exynos4210.combiner"); - busdev = SYS_BUS_DEVICE(dev); - sysbus_realize_and_unref(busdev, &error_fatal); + busdev = SYS_BUS_DEVICE(&s->int_combiner); + sysbus_realize(busdev, &error_fatal); for (n = 0; n < EXYNOS4210_MAX_INT_COMBINER_OUT_IRQ; n++) { sysbus_connect_irq(busdev, n, qdev_get_gpio_in(DEVICE(&s->a9mpcore), n)); } - exynos4210_combiner_get_gpioin(&s->irqs, dev, 0); + exynos4210_combiner_get_gpioin(&s->irqs, DEVICE(&s->int_combiner), 0); sysbus_mmio_map(busdev, 0, EXYNOS4210_INT_COMBINER_BASE_ADDR); /* External Interrupt Combiner */ - dev = qdev_new("exynos4210.combiner"); - qdev_prop_set_uint32(dev, "external", 1); - busdev = SYS_BUS_DEVICE(dev); - sysbus_realize_and_unref(busdev, &error_fatal); + qdev_prop_set_uint32(DEVICE(&s->ext_combiner), "external", 1); + busdev = SYS_BUS_DEVICE(&s->ext_combiner); + sysbus_realize(busdev, &error_fatal); for (n = 0; n < EXYNOS4210_MAX_INT_COMBINER_OUT_IRQ; n++) { sysbus_connect_irq(busdev, n, qdev_get_gpio_in(DEVICE(&s->ext_gic), n)); } - exynos4210_combiner_get_gpioin(&s->irqs, dev, 1); + exynos4210_combiner_get_gpioin(&s->irqs, DEVICE(&s->ext_combiner), 1); sysbus_mmio_map(busdev, 0, EXYNOS4210_EXT_COMBINER_BASE_ADDR); /* Initialize board IRQs. */ @@ -XXX,XX +XXX,XX @@ static void exynos4210_init(Object *obj) object_initialize_child(obj, "a9mpcore", &s->a9mpcore, TYPE_A9MPCORE_PRIV); object_initialize_child(obj, "ext-gic", &s->ext_gic, TYPE_EXYNOS4210_GIC); + object_initialize_child(obj, "int-combiner", &s->int_combiner, + TYPE_EXYNOS4210_COMBINER); + object_initialize_child(obj, "ext-combiner", &s->ext_combiner, + TYPE_EXYNOS4210_COMBINER); } static void exynos4210_class_init(ObjectClass *klass, void *data) diff --git a/hw/intc/exynos4210_combiner.c b/hw/intc/exynos4210_combiner.c index XXXXXXX..XXXXXXX 100644 --- a/hw/intc/exynos4210_combiner.c +++ b/hw/intc/exynos4210_combiner.c @@ -XXX,XX +XXX,XX @@ #include "hw/sysbus.h" #include "migration/vmstate.h" #include "qemu/module.h" - +#include "hw/intc/exynos4210_combiner.h" #include "hw/arm/exynos4210.h" #include "hw/hw.h" #include "hw/irq.h" @@ -XXX,XX +XXX,XX @@ #define DPRINTF(fmt, ...) do {} while (0) #endif -#define IIC_NGRP 64 /* Internal Interrupt Combiner - Groups number */ -#define IIC_NIRQ (IIC_NGRP * 8)/* Internal Interrupt Combiner - Interrupts number */ #define IIC_REGION_SIZE 0x108 /* Size of memory mapped region */ -#define IIC_REGSET_SIZE 0x41 - -/* - * State for each output signal of internal combiner - */ -typedef struct CombinerGroupState { - uint8_t src_mask; /* 1 - source enabled, 0 - disabled */ - uint8_t src_pending; /* Pending source interrupts before masking */ -} CombinerGroupState; - -#define TYPE_EXYNOS4210_COMBINER "exynos4210.combiner" -OBJECT_DECLARE_SIMPLE_TYPE(Exynos4210CombinerState, EXYNOS4210_COMBINER) - -struct Exynos4210CombinerState { - SysBusDevice parent_obj; - - MemoryRegion iomem; - - struct CombinerGroupState group[IIC_NGRP]; - uint32_t reg_set[IIC_REGSET_SIZE]; - uint32_t icipsr[2]; - uint32_t external; /* 1 means that this combiner is external */ - - qemu_irq output_irq[IIC_NGRP]; -}; static const VMStateDescription vmstate_exynos4210_combiner_group_state = { .name = "exynos4210.combiner.groupstate", -- 2.25.1 The only time we use the int_combiner_irq[] and ext_combiner_irq[] arrays in the Exynos4210Irq struct is during realize of the SoC -- we initialize them with the input IRQs of the combiner devices, and then connect those to outputs of other devices in exynos4210_init_board_irqs(). Now that the combiner objects are easily accessible as s->int_combiner and s->ext_combiner we can make the connections directly from one device to the other without going via these arrays. Since these are the only two remaining elements of Exynos4210Irq, we can remove that struct entirely. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20220404154658.565020-19-peter.maydell@linaro.org --- include/hw/arm/exynos4210.h | 6 ------ hw/arm/exynos4210.c | 34 ++++++++-------------------------- 2 files changed, 8 insertions(+), 32 deletions(-) diff --git a/include/hw/arm/exynos4210.h b/include/hw/arm/exynos4210.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/arm/exynos4210.h +++ b/include/hw/arm/exynos4210.h @@ -XXX,XX +XXX,XX @@ */ #define EXYNOS4210_NUM_SPLITTERS (EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ + 38) -typedef struct Exynos4210Irq { - qemu_irq int_combiner_irq[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; - qemu_irq ext_combiner_irq[EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ]; -} Exynos4210Irq; - struct Exynos4210State { /*< private >*/ SysBusDevice parent_obj; /*< public >*/ ARMCPU *cpu[EXYNOS4210_NCPUS]; - Exynos4210Irq irqs; qemu_irq irq_table[EXYNOS4210_MAX_INT_COMBINER_IN_IRQ]; MemoryRegion chipid_mem; diff --git a/hw/arm/exynos4210.c b/hw/arm/exynos4210.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/exynos4210.c +++ b/hw/arm/exynos4210.c @@ -XXX,XX +XXX,XX @@ static int mapline_size(const int *mapline) static void exynos4210_init_board_irqs(Exynos4210State *s) { uint32_t grp, bit, irq_id, n; - Exynos4210Irq *is = &s->irqs; DeviceState *extgicdev = DEVICE(&s->ext_gic); + DeviceState *intcdev = DEVICE(&s->int_combiner); + DeviceState *extcdev = DEVICE(&s->ext_combiner); int splitcount = 0; DeviceState *splitter; const int *mapline; @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) splitin = 0; for (;;) { s->irq_table[in] = qdev_get_gpio_in(splitter, 0); - qdev_connect_gpio_out(splitter, splitin, is->int_combiner_irq[in]); - qdev_connect_gpio_out(splitter, splitin + 1, is->ext_combiner_irq[in]); + qdev_connect_gpio_out(splitter, splitin, + qdev_get_gpio_in(intcdev, in)); + qdev_connect_gpio_out(splitter, splitin + 1, + qdev_get_gpio_in(extcdev, in)); splitin += 2; if (!mapline) { break; @@ -XXX,XX +XXX,XX @@ static void exynos4210_init_board_irqs(Exynos4210State *s) qdev_realize(splitter, NULL, &error_abort); splitcount++; s->irq_table[n] = qdev_get_gpio_in(splitter, 0); - qdev_connect_gpio_out(splitter, 0, is->int_combiner_irq[n]); + qdev_connect_gpio_out(splitter, 0, qdev_get_gpio_in(intcdev, n)); qdev_connect_gpio_out(splitter, 1, qdev_get_gpio_in(extgicdev, irq_id - 32)); } else { - s->irq_table[n] = is->int_combiner_irq[n]; + s->irq_table[n] = qdev_get_gpio_in(intcdev, n); } } /* @@ -XXX,XX +XXX,XX @@ uint32_t exynos4210_get_irq(uint32_t grp, uint32_t bit) return EXYNOS4210_COMBINER_GET_IRQ_NUM(grp, bit); } -/* - * Get Combiner input GPIO into irqs structure - */ -static void exynos4210_combiner_get_gpioin(Exynos4210Irq *irqs, - DeviceState *dev, int ext) -{ - int n; - int max; - qemu_irq *irq; - - max = ext ? EXYNOS4210_MAX_EXT_COMBINER_IN_IRQ : - EXYNOS4210_MAX_INT_COMBINER_IN_IRQ; - irq = ext ? irqs->ext_combiner_irq : irqs->int_combiner_irq; - - for (n = 0; n < max; n++) { - irq[n] = qdev_get_gpio_in(dev, n); - } -} - static uint8_t chipid_and_omr[] = { 0x11, 0x02, 0x21, 0x43, 0x09, 0x00, 0x00, 0x00 }; @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) sysbus_connect_irq(busdev, n, qdev_get_gpio_in(DEVICE(&s->a9mpcore), n)); } - exynos4210_combiner_get_gpioin(&s->irqs, DEVICE(&s->int_combiner), 0); sysbus_mmio_map(busdev, 0, EXYNOS4210_INT_COMBINER_BASE_ADDR); /* External Interrupt Combiner */ @@ -XXX,XX +XXX,XX @@ static void exynos4210_realize(DeviceState *socdev, Error **errp) for (n = 0; n < EXYNOS4210_MAX_INT_COMBINER_OUT_IRQ; n++) { sysbus_connect_irq(busdev, n, qdev_get_gpio_in(DEVICE(&s->ext_gic), n)); } - exynos4210_combiner_get_gpioin(&s->irqs, DEVICE(&s->ext_combiner), 1); sysbus_mmio_map(busdev, 0, EXYNOS4210_EXT_COMBINER_BASE_ADDR); /* Initialize board IRQs. */ -- 2.25.1 From: Zongyuan Li <zongyuan.li@smartx.com> Signed-off-by: Zongyuan Li <zongyuan.li@smartx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 20220324181557.203805-2-zongyuan.li@smartx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- hw/arm/realview.c | 33 ++++++++++++++++++++++++--------- 1 file changed, 24 insertions(+), 9 deletions(-) diff --git a/hw/arm/realview.c b/hw/arm/realview.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/realview.c +++ b/hw/arm/realview.c @@ -XXX,XX +XXX,XX @@ #include "hw/sysbus.h" #include "hw/arm/boot.h" #include "hw/arm/primecell.h" +#include "hw/core/split-irq.h" #include "hw/net/lan9118.h" #include "hw/net/smc91c111.h" #include "hw/pci/pci.h" +#include "hw/qdev-core.h" #include "net/net.h" #include "sysemu/sysemu.h" #include "hw/boards.h" @@ -XXX,XX +XXX,XX @@ static const int realview_board_id[] = { 0x76d }; +static void split_irq_from_named(DeviceState *src, const char* outname, + qemu_irq out1, qemu_irq out2) { + DeviceState *splitter = qdev_new(TYPE_SPLIT_IRQ); + + qdev_prop_set_uint32(splitter, "num-lines", 2); + + qdev_realize_and_unref(splitter, NULL, &error_fatal); + + qdev_connect_gpio_out(splitter, 0, out1); + qdev_connect_gpio_out(splitter, 1, out2); + qdev_connect_gpio_out_named(src, outname, 0, + qdev_get_gpio_in(splitter, 0)); +} + static void realview_init(MachineState *machine, enum realview_board_type board_type) { @@ -XXX,XX +XXX,XX @@ static void realview_init(MachineState *machine, DeviceState *dev, *sysctl, *gpio2, *pl041; SysBusDevice *busdev; qemu_irq pic[64]; - qemu_irq mmc_irq[2]; PCIBus *pci_bus = NULL; NICInfo *nd; DriveInfo *dinfo; @@ -XXX,XX +XXX,XX @@ static void realview_init(MachineState *machine, * and the PL061 has them the other way about. Also the card * detect line is inverted. */ - mmc_irq[0] = qemu_irq_split( - qdev_get_gpio_in(sysctl, ARM_SYSCTL_GPIO_MMC_WPROT), - qdev_get_gpio_in(gpio2, 1)); - mmc_irq[1] = qemu_irq_split( - qdev_get_gpio_in(sysctl, ARM_SYSCTL_GPIO_MMC_CARDIN), - qemu_irq_invert(qdev_get_gpio_in(gpio2, 0))); - qdev_connect_gpio_out_named(dev, "card-read-only", 0, mmc_irq[0]); - qdev_connect_gpio_out_named(dev, "card-inserted", 0, mmc_irq[1]); + split_irq_from_named(dev, "card-read-only", + qdev_get_gpio_in(sysctl, ARM_SYSCTL_GPIO_MMC_WPROT), + qdev_get_gpio_in(gpio2, 1)); + + split_irq_from_named(dev, "card-inserted", + qdev_get_gpio_in(sysctl, ARM_SYSCTL_GPIO_MMC_CARDIN), + qemu_irq_invert(qdev_get_gpio_in(gpio2, 0))); + dinfo = drive_get(IF_SD, 0, 0); if (dinfo) { DeviceState *card; -- 2.25.1 From: Zongyuan Li <zongyuan.li@smartx.com> Signed-off-by: Zongyuan Li <zongyuan.li@smartx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 20220324181557.203805-3-zongyuan.li@smartx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- hw/arm/stellaris.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) diff --git a/hw/arm/stellaris.c b/hw/arm/stellaris.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/stellaris.c +++ b/hw/arm/stellaris.c @@ -XXX,XX +XXX,XX @@ #include "qemu/osdep.h" #include "qapi/error.h" +#include "hw/core/split-irq.h" #include "hw/sysbus.h" #include "hw/sd/sd.h" #include "hw/ssi/ssi.h" @@ -XXX,XX +XXX,XX @@ static void stellaris_init(MachineState *ms, stellaris_board_info *board) DeviceState *ssddev; DriveInfo *dinfo; DeviceState *carddev; + DeviceState *gpio_d_splitter; BlockBackend *blk; /* @@ -XXX,XX +XXX,XX @@ static void stellaris_init(MachineState *ms, stellaris_board_info *board) &error_fatal); ssddev = ssi_create_peripheral(bus, "ssd0323"); - gpio_out[GPIO_D][0] = qemu_irq_split( - qdev_get_gpio_in_named(sddev, SSI_GPIO_CS, 0), + + gpio_d_splitter = qdev_new(TYPE_SPLIT_IRQ); + qdev_prop_set_uint32(gpio_d_splitter, "num-lines", 2); + qdev_realize_and_unref(gpio_d_splitter, NULL, &error_fatal); + qdev_connect_gpio_out( + gpio_d_splitter, 0, + qdev_get_gpio_in_named(sddev, SSI_GPIO_CS, 0)); + qdev_connect_gpio_out( + gpio_d_splitter, 1, qdev_get_gpio_in_named(ssddev, SSI_GPIO_CS, 0)); + gpio_out[GPIO_D][0] = qdev_get_gpio_in(gpio_d_splitter, 0); + gpio_out[GPIO_C][7] = qdev_get_gpio_in(ssddev, 0); /* Make sure the select pin is high. */ -- 2.25.1 From: Zongyuan Li <zongyuan.li@smartx.com> Signed-off-by: Zongyuan Li <zongyuan.li@smartx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 20220324181557.203805-5-zongyuan.li@smartx.com Resolves: https://gitlab.com/qemu-project/qemu/-/issues/811 Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- include/hw/irq.h | 5 ----- hw/core/irq.c | 15 --------------- 2 files changed, 20 deletions(-) diff --git a/include/hw/irq.h b/include/hw/irq.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/irq.h +++ b/include/hw/irq.h @@ -XXX,XX +XXX,XX @@ void qemu_free_irq(qemu_irq irq); /* Returns a new IRQ with opposite polarity. */ qemu_irq qemu_irq_invert(qemu_irq irq); -/* Returns a new IRQ which feeds into both the passed IRQs. - * It's probably better to use the TYPE_SPLIT_IRQ device instead. - */ -qemu_irq qemu_irq_split(qemu_irq irq1, qemu_irq irq2); - /* For internal use in qtest. Similar to qemu_irq_split, but operating on an existing vector of qemu_irq. */ void qemu_irq_intercept_in(qemu_irq *gpio_in, qemu_irq_handler handler, int n); diff --git a/hw/core/irq.c b/hw/core/irq.c index XXXXXXX..XXXXXXX 100644 --- a/hw/core/irq.c +++ b/hw/core/irq.c @@ -XXX,XX +XXX,XX @@ qemu_irq qemu_irq_invert(qemu_irq irq) return qemu_allocate_irq(qemu_notirq, irq, 0); } -static void qemu_splitirq(void *opaque, int line, int level) -{ - struct IRQState **irq = opaque; - irq[0]->handler(irq[0]->opaque, irq[0]->n, level); - irq[1]->handler(irq[1]->opaque, irq[1]->n, level); -} - -qemu_irq qemu_irq_split(qemu_irq irq1, qemu_irq irq2) -{ - qemu_irq *s = g_new0(qemu_irq, 2); - s[0] = irq1; - s[1] = irq2; - return qemu_allocate_irq(qemu_splitirq, s, 0); -} - void qemu_irq_intercept_in(qemu_irq *gpio_in, qemu_irq_handler handler, int n) { int i; -- 2.25.1 From: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Describe that the gic-version influences the maximum number of CPUs. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Message-id: 20220413231456.35811-1-heinrich.schuchardt@canonical.com [PMM: minor punctuation tweaks] Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- docs/system/arm/virt.rst | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/docs/system/arm/virt.rst b/docs/system/arm/virt.rst index XXXXXXX..XXXXXXX 100644 --- a/docs/system/arm/virt.rst +++ b/docs/system/arm/virt.rst @@ -XXX,XX +XXX,XX @@ gic-version Valid values are: ``2`` - GICv2 + GICv2. Note that this limits the number of CPUs to 8. ``3`` - GICv3 + GICv3. This allows up to 512 CPUs. ``host`` Use the same GIC version the host provides, when using KVM ``max`` -- 2.25.1 From: Hao Wu <wuhaotsh@google.com> Similar to the Aspeed code in include/misc/aspeed_scu.h, we define the PWRON STRAP fields in their corresponding module for NPCM7XX. Signed-off-by: Hao Wu <wuhaotsh@google.com> Reviewed-by: Patrick Venture <venture@google.com> Message-id: 20220411165842.3912945-2-wuhaotsh@google.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- include/hw/misc/npcm7xx_gcr.h | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+) diff --git a/include/hw/misc/npcm7xx_gcr.h b/include/hw/misc/npcm7xx_gcr.h index XXXXXXX..XXXXXXX 100644 --- a/include/hw/misc/npcm7xx_gcr.h +++ b/include/hw/misc/npcm7xx_gcr.h @@ -XXX,XX +XXX,XX @@ #include "exec/memory.h" #include "hw/sysbus.h" +/* + * NPCM7XX PWRON STRAP bit fields + * 12: SPI0 powered by VSBV3 at 1.8V + * 11: System flash attached to BMC + * 10: BSP alternative pins. + * 9:8: Flash UART command route enabled. + * 7: Security enabled. + * 6: HI-Z state control. + * 5: ECC disabled. + * 4: Reserved + * 3: JTAG2 enabled. + * 2:0: CPU and DRAM clock frequency. + */ +#define NPCM7XX_PWRON_STRAP_SPI0F18 BIT(12) +#define NPCM7XX_PWRON_STRAP_SFAB BIT(11) +#define NPCM7XX_PWRON_STRAP_BSPA BIT(10) +#define NPCM7XX_PWRON_STRAP_FUP(x) ((x) << 8) +#define FUP_NORM_UART2 3 +#define FUP_PROG_UART3 2 +#define FUP_PROG_UART2 1 +#define FUP_NORM_UART3 0 +#define NPCM7XX_PWRON_STRAP_SECEN BIT(7) +#define NPCM7XX_PWRON_STRAP_HIZ BIT(6) +#define NPCM7XX_PWRON_STRAP_ECC BIT(5) +#define NPCM7XX_PWRON_STRAP_RESERVE1 BIT(4) +#define NPCM7XX_PWRON_STRAP_J2EN BIT(3) +#define NPCM7XX_PWRON_STRAP_CKFRQ(x) (x) +#define CKFRQ_SKIPINIT 0x000 +#define CKFRQ_DEFAULT 0x111 + /* * Number of registers in our device state structure. Don't change this without * incrementing the version_id in the vmstate. -- 2.25.1 From: Hao Wu <wuhaotsh@google.com> This patch uses the defined fields to describe PWRON STRAPs for better readability. Signed-off-by: Hao Wu <wuhaotsh@google.com> Reviewed-by: Patrick Venture <venture@google.com> Message-id: 20220411165842.3912945-3-wuhaotsh@google.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> --- hw/arm/npcm7xx_boards.c | 24 +++++++++++++++++++----- 1 file changed, 19 insertions(+), 5 deletions(-) diff --git a/hw/arm/npcm7xx_boards.c b/hw/arm/npcm7xx_boards.c index XXXXXXX..XXXXXXX 100644 --- a/hw/arm/npcm7xx_boards.c +++ b/hw/arm/npcm7xx_boards.c @@ -XXX,XX +XXX,XX @@ #include "sysemu/sysemu.h" #include "sysemu/block-backend.h" -#define NPCM750_EVB_POWER_ON_STRAPS 0x00001ff7 -#define QUANTA_GSJ_POWER_ON_STRAPS 0x00001fff -#define QUANTA_GBS_POWER_ON_STRAPS 0x000017ff -#define KUDO_BMC_POWER_ON_STRAPS 0x00001fff -#define MORI_BMC_POWER_ON_STRAPS 0x00001fff +#define NPCM7XX_POWER_ON_STRAPS_DEFAULT ( \ + NPCM7XX_PWRON_STRAP_SPI0F18 | \ + NPCM7XX_PWRON_STRAP_SFAB | \ + NPCM7XX_PWRON_STRAP_BSPA | \ + NPCM7XX_PWRON_STRAP_FUP(FUP_NORM_UART2) | \ + NPCM7XX_PWRON_STRAP_SECEN | \ + NPCM7XX_PWRON_STRAP_HIZ | \ + NPCM7XX_PWRON_STRAP_ECC | \ + NPCM7XX_PWRON_STRAP_RESERVE1 | \ + NPCM7XX_PWRON_STRAP_J2EN | \ + NPCM7XX_PWRON_STRAP_CKFRQ(CKFRQ_DEFAULT)) + +#define NPCM750_EVB_POWER_ON_STRAPS ( \ + NPCM7XX_POWER_ON_STRAPS_DEFAULT & ~NPCM7XX_PWRON_STRAP_J2EN) +#define QUANTA_GSJ_POWER_ON_STRAPS NPCM7XX_POWER_ON_STRAPS_DEFAULT +#define QUANTA_GBS_POWER_ON_STRAPS ( \ + NPCM7XX_POWER_ON_STRAPS_DEFAULT & ~NPCM7XX_PWRON_STRAP_SFAB) +#define KUDO_BMC_POWER_ON_STRAPS NPCM7XX_POWER_ON_STRAPS_DEFAULT +#define MORI_BMC_POWER_ON_STRAPS NPCM7XX_POWER_ON_STRAPS_DEFAULT static const char npcm7xx_default_bootrom[] = "npcm7xx_bootrom.bin"; -- 2.25.1