airspy_disconnect() clears s->udev under v4l2_lock, but
airspy_stop_streaming() unconditionally calls airspy_ctrl_msg() and
airspy_free_stream_bufs() afterwards. If a streaming user closes the
device after disconnect, stop_streaming() runs and dereferences the
NULL s->udev:

  airspy_stop_streaming()
    airspy_ctrl_msg(s, CMD_RECEIVER_MODE, 0, 0, NULL, 0)
      usb_sndctrlpipe(s->udev, 0)         /* NULL deref */
    airspy_free_stream_bufs(s)
      usb_free_coherent(s->udev, ...)     /* NULL deref */

The airspy driver uses vb2_fop_release() in its file_operations, so
replace video_unregister_device(&s->vdev) with
vb2_video_unregister_device(&s->vdev) and move it before clearing
s->udev. vb2_video_unregister_device() releases the vb2 queue, which
synchronously runs airspy_stop_streaming() if streaming is active, so
the URBs, coherent DMA stream buffers and the hardware stop control
message all execute while s->udev is still valid.

vb2_video_unregister_device() locks vdev->queue->lock (vb_queue_lock)
internally, and stop_streaming() locks v4l2_lock, so the previous outer
mutex_lock(&s->vb_queue_lock) / mutex_lock(&s->v4l2_lock) pair around
the unregister sequence would self-deadlock and has been removed. A
short v4l2_lock critical section around s->udev = NULL remains so any
ioctl path that still holds the file descriptor sees coherent state.

Issue identified by automated review of the INV-003 series at
https://sashiko.dev/

Fixes: 634fe5033951 ("[media] airspy: AirSpy SDR driver")
Cc: stable@vger.kernel.org
Suggested-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Signed-off-by: Valery Borovsky <vebohr@gmail.com>
---
Changes since v1
(https://lore.kernel.org/linux-media/20260513052617.140688-1-vebohr@gmail.com/):
- Rewritten per Hans Verkuil's review
  (https://lore.kernel.org/linux-media/f202c8ae-554f-49de-a9d1-add337e28515@kernel.org/):
  fix the root cause in airspy_disconnect() by replacing
  video_unregister_device() with vb2_video_unregister_device() and
  moving it before clearing s->udev, instead of guarding the hardware
  teardown in airspy_stop_streaming() with "if (s->udev)".
  vb2_video_unregister_device() releases the queue, which synchronously
  calls stop_streaming() while s->udev is still valid, so the guard is
  no longer needed; airspy_stop_streaming() is unchanged.
- Dropped the outer mutex_lock(&s->vb_queue_lock) /
  mutex_lock(&s->v4l2_lock) around the unregister sequence:
  vb2_video_unregister_device() acquires vb_queue_lock internally and
  stop_streaming() acquires v4l2_lock, so holding either of those
  while calling the unregister helper self-deadlocks.
- Rebased on media-committers/next.

 drivers/media/usb/airspy/airspy.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/drivers/media/usb/airspy/airspy.c b/drivers/media/usb/airspy/airspy.c
index 57edb42463e8..358a66ab8e48 100644
--- a/drivers/media/usb/airspy/airspy.c
+++ b/drivers/media/usb/airspy/airspy.c
@@ -464,14 +464,21 @@ static void airspy_disconnect(struct usb_interface *intf)
 
 	dev_dbg(s->dev, "\n");
 
-	mutex_lock(&s->vb_queue_lock);
+	/*
+	 * vb2_video_unregister_device() releases the vb2 queue, which
+	 * triggers airspy_stop_streaming() if streaming is active.
+	 * stop_streaming() dereferences s->udev via airspy_ctrl_msg() and
+	 * airspy_free_stream_bufs(), so it must run before s->udev is
+	 * cleared. vb2_video_unregister_device() locks vb_queue_lock
+	 * internally and stop_streaming() locks v4l2_lock, so neither may
+	 * be held by the caller.
+	 */
+	v4l2_device_disconnect(&s->v4l2_dev);
+	vb2_video_unregister_device(&s->vdev);
+
 	mutex_lock(&s->v4l2_lock);
-	/* No need to keep the urbs around after disconnection */
 	s->udev = NULL;
-	v4l2_device_disconnect(&s->v4l2_dev);
-	video_unregister_device(&s->vdev);
 	mutex_unlock(&s->v4l2_lock);
-	mutex_unlock(&s->vb_queue_lock);
 
 	v4l2_device_put(&s->v4l2_dev);
 }
-- 
2.51.0