From nobody Wed Apr 1 20:38:04 2026 Received: from FR6P281CU001.outbound.protection.outlook.com (mail-germanywestcentralazon11020096.outbound.protection.outlook.com [52.101.171.96]) (using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits)) (No client certificate requested) by smtp.subspace.kernel.org (Postfix) with ESMTPS id E13EB3BED08; Wed, 1 Apr 2026 15:41:17 +0000 (UTC) Authentication-Results: smtp.subspace.kernel.org; arc=fail smtp.client-ip=52.101.171.96 ARC-Seal: i=2; a=rsa-sha256; d=subspace.kernel.org; s=arc-20240116; t=1775058081; cv=fail; b=c3IYf/EUqaSbMT3UUvJ4UWWtwLmeXr8xaMgp9+4bICCE+1H6K8Si1ZsoeUrvI6XCJ6YzayO0QxApeuR55R0GHtPMO2ep7CdwoRlk1GRKik7ToDbMUf8pqoFKrV0nm9QqhiY2L0ije2jgScnPBzCjN2XRd6b/pnJyNz2aZ+ezcyY= ARC-Message-Signature: i=2; a=rsa-sha256; d=subspace.kernel.org; s=arc-20240116; t=1775058081; c=relaxed/simple; bh=wXxFSa5GWL1DE7Wda07EH8V7rprCeZntpYG1MNaYTpk=; h=From:To:Cc:Subject:Date:Message-ID:Content-Type:MIME-Version; b=bO/wYbX1J5B/DVljszU332k2Q+04g2BxB+VtWOqzuudRAF+8eA2tIjIYnokug8/ViWa37/CAFQJ359Cs+hpawa3wx4rnxlasB7Fjx4U+s21P91r+jGLTW5ph6q4RV78LvH1RTjDgn5saTPzMJTCGSiQDd/4FRLS3qRVn/ycTSJY= ARC-Authentication-Results: i=2; smtp.subspace.kernel.org; dmarc=pass (p=reject dis=none) header.from=arctic.de; spf=pass smtp.mailfrom=arctic.de; dkim=pass (2048-bit key) header.d=Arctic.de header.i=@Arctic.de header.b=LfoJtCZT; arc=fail smtp.client-ip=52.101.171.96 Authentication-Results: smtp.subspace.kernel.org; dmarc=pass (p=reject dis=none) header.from=arctic.de Authentication-Results: smtp.subspace.kernel.org; spf=pass smtp.mailfrom=arctic.de Authentication-Results: smtp.subspace.kernel.org; dkim=pass (2048-bit key) header.d=Arctic.de header.i=@Arctic.de header.b="LfoJtCZT" ARC-Seal: i=1; a=rsa-sha256; s=arcselector10001; d=microsoft.com; cv=none; b=PaUDQ4cpk+/Sywgup7OrNy0cTDXpfHd83XvnUSz3bucULwmrFBhvzQiPe5Kmx1xFHqHEu8E92LmzBLAlb/yYRkKntpkwiQ8YwdvTgVgsKUyDEGb8GwvboTXvsBqJpq+wQoC5oQGQGyoz/jTT4+m82oR06U9RHkCcn7oH8mtrsfRdrEeJugVq3Bz/TqCxGY4ily4WLEfm9XuAfmfUxcIkavJbBhBA5f/d40tPwzkMWYP5hZ5K8gJ069gvepn92POszDBt+3AJn7l5VtPY1dz28BrKGLFNCO+H50jT2eHaJYFG0FchG7vfbYP0/nqyBvoAeuVCWNxP2LHnNF7RwHCH0A== ARC-Message-Signature: i=1; a=rsa-sha256; c=relaxed/relaxed; d=microsoft.com; s=arcselector10001; h=From:Date:Subject:Message-ID:Content-Type:MIME-Version:X-MS-Exchange-AntiSpam-MessageData-ChunkCount:X-MS-Exchange-AntiSpam-MessageData-0:X-MS-Exchange-AntiSpam-MessageData-1; bh=X8O1fYe3YDs0AuxtHDeKs0sVKzLrMtMaKcxs0nXXd1A=; b=RwM/kTyadRAEUzszHIi1p44v2fXg/XWIpFrR95JPe7Jwo/mdjW+YBi8PPy8V18soJwVuxhc9/tMTQiSXwPdOKOip/AFUVXhdmLv6JAOGFiaITrYl06xN9iexnLYQYbJVdGtnDvCs8FLIVCquUKb0EDdGF852nY3R9k1kc+QxMqZ91ym2p9qW67fgJicpvyt8beWfBhKOSHbChHEa5RE+IHaR4wlq+NMlgLjPKdHUmzhh++AmX/JVA/hho1eqjWBJKNytvSGP5SBrcMYrp941mMih5eUK/Czc/xwvPHZutl9kPLCW1tycyEslOZ6q2BA2XH3w2KH7iO0VcJpIEtifhQ== ARC-Authentication-Results: i=1; mx.microsoft.com 1; spf=pass smtp.mailfrom=arctic.de; dmarc=pass action=none header.from=arctic.de; dkim=pass header.d=arctic.de; arc=none DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=Arctic.de; s=selector1; h=From:Date:Subject:Message-ID:Content-Type:MIME-Version:X-MS-Exchange-SenderADCheck; bh=X8O1fYe3YDs0AuxtHDeKs0sVKzLrMtMaKcxs0nXXd1A=; b=LfoJtCZTsW5sXt6eko2T+J0NpVn7cyh++ibeJDBEqNzOsKn5BDaedHT1kNcg/Ius7lkk4hw7qs8qLxvr3+koH4PEpBjRGvAg6XSQeK/YCo++OzUqao5khQKTWAagz6s4jTzfh4JiAMvVKpg2KOaOhDU3QHsdyqSiXWN3BHrkpvssUf3ZWFzJhmsXSUluKuK/lnU51YZnqakaD6Wqb8pxxMUivcx+CT15t2ShxcrpPQQHk5EfEuIXPRdishge/FzYNjUC4/KalmYUIYXIVH/Ve4DBs6P3Cb1izf4MTdz/Su+Pq0UMhqlCbYWVLUSw69Dp1/N8QYtt5Z/F8RCjwBUv5w== Authentication-Results: dkim=none (message not signed) header.d=none;dmarc=none action=none header.from=arctic.de; Received: from FR6P281MB5900.DEUP281.PROD.OUTLOOK.COM (2603:10a6:d10:1bf::9) by FR5P281MB5287.DEUP281.PROD.OUTLOOK.COM (2603:10a6:d10:198::8) with Microsoft SMTP Server (version=TLS1_2, cipher=TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384) id 15.20.9769.18; Wed, 1 Apr 2026 15:41:14 +0000 Received: from FR6P281MB5900.DEUP281.PROD.OUTLOOK.COM ([fe80::7eba:ac95:a60d:521c]) by FR6P281MB5900.DEUP281.PROD.OUTLOOK.COM ([fe80::7eba:ac95:a60d:521c%3]) with mapi id 15.20.9769.014; Wed, 1 Apr 2026 15:41:14 +0000 From: Aureo Serrano de Souza To: linux-hwmon@vger.kernel.org Cc: linux@roeck-us.net, linux@weissschuh.net, corbet@lwn.net, skhan@linuxfoundation.org, linux-doc@vger.kernel.org, linux-kernel@vger.kernel.org, Aureo Serrano de Souza Subject: [PATCH v6] hwmon: add driver for ARCTIC Fan Controller Date: Wed, 1 Apr 2026 23:39:47 +0800 Message-ID: <20260401153949.77488-1-aureo.serrano@arctic.de> X-Mailer: git-send-email 2.43.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: quoted-printable X-ClientProxiedBy: TPYP295CA0036.TWNP295.PROD.OUTLOOK.COM (2603:1096:7d0:7::8) To FR6P281MB5900.DEUP281.PROD.OUTLOOK.COM (2603:10a6:d10:1bf::9) Precedence: bulk X-Mailing-List: linux-kernel@vger.kernel.org List-Id: List-Subscribe: List-Unsubscribe: MIME-Version: 1.0 X-MS-PublicTrafficType: Email X-MS-TrafficTypeDiagnostic: FR6P281MB5900:EE_|FR5P281MB5287:EE_ X-MS-Office365-Filtering-Correlation-Id: 3e82b7d2-674b-4d3f-dddd-08de90051b6f X-MS-Exchange-AtpMessageProperties: SA X-MS-Exchange-SenderADCheck: 1 X-MS-Exchange-AntiSpam-Relay: 0 X-Microsoft-Antispam: BCL:0;ARA:13230040|376014|52116014|366016|1800799024|38350700014|18002099003|56012099003|55112099003; X-Microsoft-Antispam-Message-Info: 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 X-Forefront-Antispam-Report: CIP:255.255.255.255;CTRY:;LANG:en;SCL:1;SRV:;IPV:NLI;SFV:NSPM;H:FR6P281MB5900.DEUP281.PROD.OUTLOOK.COM;PTR:;CAT:NONE;SFS:(13230040)(376014)(52116014)(366016)(1800799024)(38350700014)(18002099003)(56012099003)(55112099003);DIR:OUT;SFP:1102; X-MS-Exchange-AntiSpam-MessageData-ChunkCount: 1 X-MS-Exchange-AntiSpam-MessageData-0: =?utf-8?B?QUFyekd2TllXcENzNEoyNS9GQmdjUzBSMDJERSt5K2EzeURQK3RzbG9wYnkz?= =?utf-8?B?TVBwOHcva1EvdUhjU0FOaVhrbFU0aW9YWGFZeDBaa2xTaHhWd2I4ZlVzbUhM?= =?utf-8?B?R0JmVzZOcHl6aGRsWXR1Ym5hUXNJTHo0OEdUWjI1SWxRaHdZL2EwNWtFZTgv?= =?utf-8?B?aVZJTEhOZjdWNFRhTEdsOXRNSnpNQ3JvbDhDTDRNWXFjYW9GSXNZWHlzSXp3?= =?utf-8?B?VXBrcHc3UEoyeWJrYXJFRnJmdUpKRWRjMDN2amQ4UUZJM1NxbkxUTzBZQTUv?= =?utf-8?B?My8yNFdBMGpXeUh6VitqY29YQXFwWk02eWdLRkMrT1VNY2VmaGtpWHYya0lV?= =?utf-8?B?b241NWJlZC9NSkNndDRQTEFJSnd4aHl4ZDRseFd3TXRjcmJvVVFDOHN0T2pu?= =?utf-8?B?eDJXUkxQakpHVjVDeEVFUHN0Tm1KSFZrTXl3VVM0YjBxV2hFYzIrNTJKY0Q0?= =?utf-8?B?Yy9QTlViWmVFUU5nang2N09wZXdxTTFvK2wrcXI5VmpBdEZMRVZLb1dzMXY3?= =?utf-8?B?bnFoU0ZuaktRMkNRYTU5aWJIQ0RwcEhpbWwwWEx6UTJBZjBFaVk3Rm42Z2N1?= =?utf-8?B?ZWhDcTE4VVVSVGVaQk1OR3FoWmJNTk9EZ2llTnM1RCtxS25RL25WWkp3T0Ri?= =?utf-8?B?ZnNldHppTkRsL1hLS2VFTnRrY1RVenpKUTJlY2E5dDBBOHp6RXNydGJIeGth?= =?utf-8?B?VjZTb0k2cEdZQmFMcUN4TVdCcWV3M2J5T0x3bDVyREIxblZ5M0hZS3N6Nmcx?= =?utf-8?B?ekwyWjI5Z3lMSVdFWjdWdnRsUnM3eFpyOVF1SWlRV3dta3RPa1BTRmE5aWVD?= =?utf-8?B?K2hrdklVZkxuaWtRUlpDdWVzVDJuQTNKRVowTk1DNW41MGIvUFJYTG5TQXZU?= =?utf-8?B?Qy9uTStiNllXZjI1dzhzYitXN1R0ckt6WEZuNTZSRmpZdGRjUmdsYUxFYjlz?= =?utf-8?B?b29rUEt1bDZPQzNxaGN2bnYzMnpjQnRhZFB4TG9TeGZjNnJ1Q0RSYm5sblBT?= =?utf-8?B?NzFrVmtheDVCSE1wRnBCYXVXWjVKMHREVG9RQm0yMStFWllka1FUM2c1TnBO?= =?utf-8?B?Z2RDYjB0NlVIT1RBZ01qbUJKQWhLNlRNc09iemtlUGVsR3NYMHBzaWZwT1V2?= =?utf-8?B?aE5pUXdRemc3Q2dKSjFGR1M5ak8yMjN6UkMxZGdFQjJwTWc3cmV2YVMyVFFK?= =?utf-8?B?T3BHZ2Q3ZlhqeFVPcTZpWDlwVUVaa3hWdjAxaGd6eW43S016UC85TWgxN0Ri?= =?utf-8?B?cDNsY1A4ckFYZ29rbFMwOWluU1c0VUF0cVhlZjN5R0VTYnVicFZzMmpBRytq?= =?utf-8?B?c1VodFVDTGp2Mjk5OWdSM0dUYVpoL0JhaUlwRzFZay9obnhYQUtObnhVeU1N?= =?utf-8?B?M0FKOEVNT280b3BlRmFZcW5NQlBGN1l5ckZ2L3lmT1dQTFp5ak9TL3VjU2M5?= =?utf-8?B?d3BFTVZQSjF1K1FrRmNrcW1SV05GU3VFcUFGRmZoeUVyUTFqSmpsMk1pTHF5?= =?utf-8?B?TFRsbFQxN3d5enpEWVVJV1RGY1k4Q3U1Z0VPOWFRSXRrSXRrYVhPb3YvUHVP?= =?utf-8?B?Vng1ZHdzSWtMTVR6Y0k1VWhOMDYydEZ2cXUxQ2hXRk5oNWVKemZ6ZnZoT3h5?= =?utf-8?B?RXlKdll3Tklna2lkMEUzcm1nZDh1VHludmFrcmk2RlFOMUE0N2xOaEZjd3dv?= =?utf-8?B?Y01CWnZJcFAyTzRwQ0NyMWdFL3ptOE5JZi9ZbkMxOU5HdDZ0bFZEUkx2Rm54?= =?utf-8?B?T1pVM0JzYzM1SjdVaHZwczdBNUMrNmxmODRBQTN5bGg2NHo4NS9zdG5tSjJp?= =?utf-8?B?cWRUYVdhcTgzd21HOFJkOVA5VURuZ2NVR0tibmcyQ1VFMW9PWTV0TkY2ZUQ5?= =?utf-8?B?ZnFoalEzTTVHMzByU05pRERxSC9TU3p6WnNiVDF3NURPNWVvQWptOUVDNlRY?= =?utf-8?B?WEE1cDRXakR4Wk5BQ1BtUWVhUTVUMjFCK2xtSjN5cE4zWmJaek1YYUNOL0tG?= =?utf-8?B?UmtZVkdXQTZRbE43RXVIeDZ6NWFPUGx1cDZzMmd2TFp1ZzR3RUtvZndPK0Fa?= =?utf-8?B?RUFpcXFDZjNiZ3dBcVJqTlNmMC9GcVZzcG9mMFhWS1E4bk9WY04rQ1NVeXdV?= =?utf-8?B?T3A4a3J4bS9xMWY4SFAycndZMGhsU0RhdmJGRzE5TjlORGh0R04veENBZWxT?= =?utf-8?B?Vm01SWF3S1hFSkhrYWJQei9RVHVWbThSQkRKUVJGSXpsNFF4QTl2bWIxSmRL?= =?utf-8?B?dnN6UVRDVnJmYzlSaW1iRWNlczI5bTF6cnBYdmZrTk56dHhBNkZUZEdXdW1y?= =?utf-8?B?YVR4a1RFeFNNaGVEcHZoazczUTdGbHkzK2Z5MGtxN293R05mald5blA1WnNO?= =?utf-8?Q?pRcNWuXUZfq+NDUE=3D?= X-OriginatorOrg: Arctic.de X-MS-Exchange-CrossTenant-Network-Message-Id: 3e82b7d2-674b-4d3f-dddd-08de90051b6f X-MS-Exchange-CrossTenant-AuthSource: FR6P281MB5900.DEUP281.PROD.OUTLOOK.COM X-MS-Exchange-CrossTenant-AuthAs: Internal X-MS-Exchange-CrossTenant-OriginalArrivalTime: 01 Apr 2026 15:41:14.5633 (UTC) X-MS-Exchange-CrossTenant-FromEntityHeader: Hosted X-MS-Exchange-CrossTenant-Id: 51cc2c5f-af21-4667-81ec-d88d36e264bb X-MS-Exchange-CrossTenant-MailboxType: HOSTED X-MS-Exchange-CrossTenant-UserPrincipalName: vOf9yvi9jMkbL21u1vvxZ2qGe9siuNhRzXQOnYKtnVmtP+CwfenyZn75XWDPGAGHzJup1tj7QtJnc30SiR+8/w== X-MS-Exchange-Transport-CrossTenantHeadersStamped: FR5P281MB5287 Add hwmon driver for the ARCTIC Fan Controller, a USB HID device (VID 0x3904, PID 0xF001) with 10 fan channels. Exposes fan speed in RPM (read-only) and PWM duty cycle (0-255, read/write) via sysfs. The device pushes IN reports at ~1 Hz containing RPM readings. PWM is set via OUT reports; the device applies the new duty cycle and sends back a 2-byte ACK (Report ID 0x02). The driver waits up to 1 s for the ACK using a completion. Measured device latency: max ~563 ms over 500 iterations. PWM control is manual-only: the device never changes duty cycle autonomously. raw_event() may run in hardirq context, so fan_rpm[] is protected by a spinlock with irq-save. pwm_duty[] is also protected by this spinlock because reset_resume() clears it outside the hwmon core lock. The OUT report buffer is built and write_pending is armed under the same lock so that no reset_resume() can race with the pwm_duty[] snapshot. priv->buf is exclusively accessed by write(), which the hwmon core serializes. Signed-off-by: Aureo Serrano de Souza --- Thanks to Guenter Roeck and Thomas Wei=C3=9Fschuh for the reviews. Changes since v5: - arctic_fan_probe(): switch from devm_hwmon_device_register_with_info() to hwmon_device_register_with_info(); store the returned pointer in priv->hwmon_dev for explicit teardown in remove() - arctic_fan_remove(): call hwmon_device_unregister(priv->hwmon_dev) before hid_device_io_stop/hid_hw_close/hid_hw_stop; this closes the use-after-free window where a concurrent sysfs write could call hid_hw_output_report() on an already-stopped device; matches the removal pattern used by nzxt-smart2 and aquacomputer_d5next - arctic_fan_write(): expand write_pending comment to document the residual theoretical late-ACK race (unfixable without a correlation ID in the device ACK report) and its practical impossibility (observed max ACK latency ~563 ms, timeout 1 s; a delay > 1 s indicates a non-functional device) - arctic_fan_reset_resume(), arctic_fan_read(), arctic_fan_write(): extend in_report_lock coverage to pwm_duty[]; reset_resume() clears pwm_duty[] outside the hwmon core lock, so all paths that read or write pwm_duty[] now hold in_report_lock to prevent a data race during resume - arctic_fan_write(): build the OUT report buffer inside in_report_lock so reset_resume() cannot clear pwm_duty[] between the pwm_duty[] snapshot and the buffer write; this makes the lock coverage complete Changes since v4: - arctic_fan_write(): switch to wait_for_completion_timeout() (non- interruptible); eliminates the signal-interrupted write case of the late-ACK race that write_pending could not fully prevent - arctic_fan_write(): guard pwm_duty[channel] commit with ack_status =3D=3D 0 check; a device error ACK (status 0x01) no longer silently poisons the cached duty used in future OUT reports - arctic_fan_probe()/remove(): replace devm_add_action_or_reset() + no-op remove() with explicit hid_device_io_stop/hid_hw_close/ hid_hw_stop in remove(); devm_add_action_or_reset() was called after hdev->driver =3D NULL, causing a NULL deref in hid_hw_close() on unbind - add reset_resume callback: device resets PWM to hardware defaults on power loss during suspend; driver now clears cached pwm_duty[] on reset-resume so stale pre-suspend values are not re-sent as if valid - Documentation/hwmon/arctic_fan_controller.rst: document suspend/ resume behaviour and the updated pwm[1-10] read semantics Changes since v3: - buf[]: upgrade from __aligned(8) to ____cacheline_aligned so the DMA buffer occupies its own cache line, preventing false sharing with adjacent fan_rpm[]/pwm_duty[] fields on non-coherent architectures - arctic_fan_write(): add write_pending flag (protected by in_report_lock) so raw_event() delivers ACKs only while a write is in flight - arctic_fan_write(): commit pwm_duty[channel] only after the device ACKs the command; a failed or timed-out write no longer leaves a stale value in the cached duty state - arctic_fan_probe(): start IO (hid_device_io_start) before registering with hwmon; previously a sysfs write arriving between hwmon registration and io_start could send an OUT report whose ACK would be discarded by the HID core, causing a spurious timeout - Documentation/hwmon/arctic_fan_controller.rst: document that cached PWM values start at 0 (hardware state unknown at probe) and that each OUT report carries all 10 channel values Changes since v2: - buf[]: add __aligned(8) for DMA safety - ARCTIC_ACK_TIMEOUT_MS: restore 1000 ms; note observed max ~563 ms - arctic_fan_parse_report(): replace hwmon_lock/hwmon_unlock with spin_lock_irqsave; hwmon_lock() may sleep and is unsafe when raw_event() runs in hardirq/softirq context - arctic_fan_raw_event(): use spin_lock_irqsave for ACK path - arctic_fan_write(): use spin_lock_irqsave for completion reinit - arctic_fan_write(): clamp val to [0, 255] before u8 cast - remove priv->hwmon_dev (no longer needed) Changes since v1: - Use hid_dbg() instead of module_param debug flag - Move hid_device_id table adjacent to hid_driver struct - Use get_unaligned_le16() for RPM parsing - Remove impossible bounds/NULL checks; remove retry loop - Add hid_is_usb() guard - Do not update pwm_duty from IN reports (device is manual-only) - Add completion/ACK mechanism for OUT report acknowledgement - Add Documentation/hwmon/arctic_fan_controller.rst and MAINTAINERS diff --git a/Documentation/hwmon/arctic_fan_controller.rst b/Documentation/= hwmon/arctic_fan_controller.rst new file mode 100644 index 0000000000..b5be88ae46 --- /dev/null +++ b/Documentation/hwmon/arctic_fan_controller.rst @@ -0,0 +1,56 @@ +.. SPDX-License-Identifier: GPL-2.0-or-later + +Kernel driver arctic_fan_controller +=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D + +Supported devices: + +* ARCTIC Fan Controller (USB HID, VID 0x3904, PID 0xF001) + +Author: Aureo Serrano de Souza + +Description +----------- + +This driver provides hwmon support for the ARCTIC Fan Controller, a USB +Custom HID device with 10 fan channels. The device sends IN reports about +once per second containing current RPM values (bytes 11-30, 10 x uint16 LE= ). +Fan speed control is manual-only: the device does not change PWM +autonomously; it only applies a new duty cycle when it receives an OUT +report from the host. + +After the device applies an OUT report, it sends back a 2-byte ACK IN +report (Report ID 0x02, byte 1 =3D 0x00 on success) confirming the command +was applied. + +Usage notes +----------- + +Since it is a USB device, hotplug is supported. The device is autodetected. + +The device does not support GET_REPORT, so the driver cannot read back the +current hardware PWM state at probe time. The cached PWM values (readable +via pwm[1-10]) start at 0 and reflect only values that have been +successfully written. Because each OUT report carries all 10 channel value= s, +writing a single channel also sends the cached values for all other channe= ls. +Users should set all channels to the desired values before relying on the +cached state. + +On system suspend, the device may lose power and reset its PWM channels to +hardware defaults. The driver clears its cached duty values on resume so +that reads reflect the unknown hardware state rather than stale pre-suspend +values. Userspace is responsible for re-applying the desired duty cycles +after resume. + +Sysfs entries +------------- + +=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D =3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D +fan[1-10]_input Fan speed in RPM (read-only). Updated from IN reports at = ~1 Hz. +pwm[1-10] PWM duty cycle (0-255). Write: sends an OUT report settin= g the + duty cycle (scaled from 0-255 to 0-100% for the device); + the cached value is updated only after the device ACKs the + command with a success status. Read: returns the last + successfully written value; initialized to 0 at driver lo= ad + and after resume (hardware state unknown). +=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D =3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D= =3D=3D=3D=3D diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst index b2ca8513cf..c34713040e 100644 --- a/Documentation/hwmon/index.rst +++ b/Documentation/hwmon/index.rst @@ -42,6 +42,7 @@ Hardware Monitoring Kernel Drivers aht10 amc6821 aquacomputer_d5next + arctic_fan_controller asb100 asc7621 aspeed-g6-pwm-tach diff --git a/MAINTAINERS b/MAINTAINERS index 96ea84948d..ec3112bd41 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2053,6 +2053,13 @@ S: Maintained F: drivers/net/arcnet/ F: include/uapi/linux/if_arcnet.h +ARCTIC FAN CONTROLLER DRIVER +M: Aureo Serrano de Souza +L: linux-hwmon@vger.kernel.org +S: Maintained +F: Documentation/hwmon/arctic_fan_controller.rst +F: drivers/hwmon/arctic_fan_controller.c + ARM AND ARM64 SoC SUB-ARCHITECTURES (COMMON PARTS) M: Arnd Bergmann M: Krzysztof Kozlowski diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 328867242c..6c90a8dd40 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -388,6 +388,18 @@ config SENSORS_APPLESMC Say Y here if you have an applicable laptop and want to experience the awesome power of applesmc. +config SENSORS_ARCTIC_FAN_CONTROLLER + tristate "ARCTIC Fan Controller" + depends on USB_HID + help + If you say yes here you get support for the ARCTIC Fan Controller, + a USB HID device (VID 0x3904, PID 0xF001) with 10 fan channels. + The driver exposes fan speed (RPM) and PWM control via the hwmon + sysfs interface. + + This driver can also be built as a module. If so, the module + will be called arctic_fan_controller. + config SENSORS_ARM_SCMI tristate "ARM SCMI Sensors" depends on ARM_SCMI_PROTOCOL diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile index 5833c807c6..ef831c3375 100644 --- a/drivers/hwmon/Makefile +++ b/drivers/hwmon/Makefile @@ -49,6 +49,7 @@ obj-$(CONFIG_SENSORS_ADT7475) +=3D adt7475.o obj-$(CONFIG_SENSORS_AHT10) +=3D aht10.o obj-$(CONFIG_SENSORS_APPLESMC) +=3D applesmc.o obj-$(CONFIG_SENSORS_AQUACOMPUTER_D5NEXT) +=3D aquacomputer_d5next.o +obj-$(CONFIG_SENSORS_ARCTIC_FAN_CONTROLLER) +=3D arctic_fan_controller.o obj-$(CONFIG_SENSORS_ARM_SCMI) +=3D scmi-hwmon.o obj-$(CONFIG_SENSORS_ARM_SCPI) +=3D scpi-hwmon.o obj-$(CONFIG_SENSORS_AS370) +=3D as370-hwmon.o diff --git a/drivers/hwmon/arctic_fan_controller.c b/drivers/hwmon/arctic_f= an_controller.c new file mode 100644 index 0000000000..2bfb003f01 --- /dev/null +++ b/drivers/hwmon/arctic_fan_controller.c @@ -0,0 +1,370 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Linux hwmon driver for ARCTIC Fan Controller + * + * USB Custom HID device with 10 fan channels. + * Exposes fan RPM (input) and PWM (0-255) via hwmon. Device pushes IN rep= orts + * at ~1 Hz; no GET_REPORT. OUT reports set PWM duty (bytes 1-10, 0-100%). + * PWM is manual-only: the device does not change duty autonomously, only + * when it receives an OUT report from the host. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define ARCTIC_VID 0x3904 +#define ARCTIC_PID 0xF001 +#define ARCTIC_NUM_FANS 10 +#define ARCTIC_OUTPUT_REPORT_ID 0x01 +#define ARCTIC_REPORT_LEN 32 +#define ARCTIC_RPM_OFFSET 11 /* bytes 11-30: 10 x uint16 LE */ +/* ACK report: device sends Report ID 0x02, 2 bytes (ID + status) after ap= plying OUT report */ +#define ARCTIC_ACK_REPORT_ID 0x02 +#define ARCTIC_ACK_REPORT_LEN 2 +/* + * Time to wait for ACK report after send. + * Measured over 500 iterations: max ~563 ms. Keep 1 s as margin. + */ +#define ARCTIC_ACK_TIMEOUT_MS 1000 + +struct arctic_fan_data { + struct hid_device *hdev; + struct device *hwmon_dev; /* stored for explicit unregister in remove() */ + spinlock_t in_report_lock; /* protects fan_rpm, ack_status, write_pending= , pwm_duty */ + struct completion in_report_received; /* ACK (ID 0x02) received in raw_ev= ent */ + int ack_status; /* 0 =3D OK, negative errno on device error */ + bool write_pending; /* true while an OUT report ACK is in flight */ + u32 fan_rpm[ARCTIC_NUM_FANS]; + u8 pwm_duty[ARCTIC_NUM_FANS]; /* 0-255 matching sysfs range; converted to= 0-100 on send */ + /* + * OUT report buffer. Cache-line aligned so it occupies its own cache + * line, preventing DMA cache-coherency issues with adjacent fields + * (fan_rpm[], pwm_duty[]) on non-coherent architectures. + * Embedded in the devm_kzalloc'd struct so it is heap-allocated and + * passes usb_hcd_map_urb_for_dma(). Serialized by the hwmon core. + */ + u8 buf[ARCTIC_REPORT_LEN] ____cacheline_aligned; +}; + +/* + * Parse RPM values from the periodic status report (10 x uint16 LE at rpm= _off). + * pwm_duty is not updated from the report: the device is manual-only, so = the + * host cache is the authoritative source for PWM. + * Called from raw_event which may run in IRQ context; must not sleep. + */ +static void arctic_fan_parse_report(struct arctic_fan_data *priv, u8 *buf, + int len, int rpm_off) +{ + unsigned long flags; + int i; + + if (len < rpm_off + 20) + return; + + spin_lock_irqsave(&priv->in_report_lock, flags); + for (i =3D 0; i < ARCTIC_NUM_FANS; i++) + priv->fan_rpm[i] =3D get_unaligned_le16(&buf[rpm_off + i * 2]); + spin_unlock_irqrestore(&priv->in_report_lock, flags); +} + +/* + * raw_event: IN reports. + * + * Status report: Report ID 0x01, 32 bytes: + * byte 0 =3D report ID, bytes 1-10 =3D PWM 0-100%, bytes 11-30 =3D 10 x= RPM uint16 LE. + * Device pushes these at ~1 Hz; no GET_REPORT. + * + * ACK report: Report ID 0x02, 2 bytes: + * byte 0 =3D 0x02, byte 1 =3D status (0x00 =3D OK, 0x01 =3D ERROR). + * Sent once after accepting and applying an OUT report (ID 0x01). + */ +static int arctic_fan_raw_event(struct hid_device *hdev, + struct hid_report *report, u8 *data, int size) +{ + struct arctic_fan_data *priv =3D hid_get_drvdata(hdev); + unsigned long flags; + + hid_dbg(hdev, "arctic_fan: raw_event id=3D%u size=3D%d\n", report->id, si= ze); + + if (report->id =3D=3D ARCTIC_ACK_REPORT_ID && size =3D=3D ARCTIC_ACK_REPO= RT_LEN) { + spin_lock_irqsave(&priv->in_report_lock, flags); + /* + * Only deliver if a write is in flight. This prevents a + * late-arriving ACK from a timed-out write from erroneously + * satisfying a subsequent write's completion wait. + */ + if (priv->write_pending) { + priv->ack_status =3D data[1] =3D=3D 0x00 ? 0 : -EIO; + complete(&priv->in_report_received); + } + spin_unlock_irqrestore(&priv->in_report_lock, flags); + return 0; + } + + if (report->id !=3D ARCTIC_OUTPUT_REPORT_ID || size !=3D ARCTIC_REPORT_LE= N) { + hid_dbg(hdev, "arctic_fan: raw_event id=3D%u size=3D%d ignored\n", + report->id, size); + return 0; + } + + arctic_fan_parse_report(priv, data, size, ARCTIC_RPM_OFFSET); + return 0; +} + +static umode_t arctic_fan_is_visible(const void *data, + enum hwmon_sensor_types type, + u32 attr, int channel) +{ + if (type =3D=3D hwmon_fan && attr =3D=3D hwmon_fan_input) + return 0444; + if (type =3D=3D hwmon_pwm && attr =3D=3D hwmon_pwm_input) + return 0644; + return 0; +} + +static int arctic_fan_read(struct device *dev, enum hwmon_sensor_types typ= e, + u32 attr, int channel, long *val) +{ + struct arctic_fan_data *priv =3D dev_get_drvdata(dev); + unsigned long flags; + + if (type =3D=3D hwmon_fan && attr =3D=3D hwmon_fan_input) { + spin_lock_irqsave(&priv->in_report_lock, flags); + *val =3D priv->fan_rpm[channel]; + spin_unlock_irqrestore(&priv->in_report_lock, flags); + return 0; + } + if (type =3D=3D hwmon_pwm && attr =3D=3D hwmon_pwm_input) { + spin_lock_irqsave(&priv->in_report_lock, flags); + *val =3D priv->pwm_duty[channel]; + spin_unlock_irqrestore(&priv->in_report_lock, flags); + return 0; + } + return -EINVAL; +} + +static int arctic_fan_write(struct device *dev, enum hwmon_sensor_types ty= pe, + u32 attr, int channel, long val) +{ + struct arctic_fan_data *priv =3D dev_get_drvdata(dev); + u8 new_duty =3D (u8)clamp_val(val, 0, 255); + unsigned long flags; + unsigned long t; + int i, ret; + + /* + * Build the buffer and arm write_pending under in_report_lock so that + * reset_resume() cannot clear pwm_duty[] between the pwm_duty[] read + * and the buffer write, and raw_event() cannot deliver a stale ACK + * from a previous write into this write's completion. + * + * priv->buf is heap-allocated (embedded in the devm_kzalloc'd struct), + * satisfying usb_hcd_map_urb_for_dma(). Exclusively accessed by + * write() which the hwmon core serializes. + * + * pwm_duty[channel] is committed only after a positive device ACK so a + * failed or timed-out write does not corrupt the cached state. + * + * Residual theoretical race: if write A times out (write_pending + * cleared), write B sets write_pending =3D true, and a late ACK from + * write A=E2=80=94delayed beyond ARCTIC_ACK_TIMEOUT_MS=E2=80=94arrives d= uring write + * B's pending window, it would falsely satisfy write B's completion. + * This cannot be prevented in driver code without protocol support + * (for example, a correlation ID echoed in the device ACK report). + * In testing, observed ACK latency stayed below the 1 s timeout + * (maximum ~563 ms over 500 iterations). + * + * The wait is non-interruptible so that a signal cannot cause write() + * to return early while the OUT report is already in flight; an + * interruptible early return would create the same late-ACK window + * without even the timeout guard. + * Serialized by the hwmon core: only one arctic_fan_write() at a time. + * Use irqsave to match the IRQ context in which raw_event may run. + */ + spin_lock_irqsave(&priv->in_report_lock, flags); + priv->buf[0] =3D ARCTIC_OUTPUT_REPORT_ID; + for (i =3D 0; i < ARCTIC_NUM_FANS; i++) { + u8 d =3D i =3D=3D channel ? new_duty : priv->pwm_duty[i]; + + priv->buf[1 + i] =3D DIV_ROUND_CLOSEST((unsigned int)d * 100, 255); + } + priv->ack_status =3D -ETIMEDOUT; + priv->write_pending =3D true; + reinit_completion(&priv->in_report_received); + spin_unlock_irqrestore(&priv->in_report_lock, flags); + + ret =3D hid_hw_output_report(priv->hdev, priv->buf, ARCTIC_REPORT_LEN); + if (ret < 0) { + spin_lock_irqsave(&priv->in_report_lock, flags); + priv->write_pending =3D false; + spin_unlock_irqrestore(&priv->in_report_lock, flags); + return ret; + } + + t =3D wait_for_completion_timeout(&priv->in_report_received, + msecs_to_jiffies(ARCTIC_ACK_TIMEOUT_MS)); + spin_lock_irqsave(&priv->in_report_lock, flags); + priv->write_pending =3D false; + /* Commit inside the lock so reset_resume() cannot race with this write */ + if (t && priv->ack_status =3D=3D 0) + priv->pwm_duty[channel] =3D new_duty; + spin_unlock_irqrestore(&priv->in_report_lock, flags); + + if (!t) + return -ETIMEDOUT; + return priv->ack_status; /* 0=3DOK, -EIO=3Ddevice error */ +} + +static const struct hwmon_ops arctic_fan_ops =3D { + .is_visible =3D arctic_fan_is_visible, + .read =3D arctic_fan_read, + .write =3D arctic_fan_write, +}; + +static const struct hwmon_channel_info *arctic_fan_info[] =3D { + HWMON_CHANNEL_INFO(fan, + HWMON_F_INPUT, HWMON_F_INPUT, HWMON_F_INPUT, + HWMON_F_INPUT, HWMON_F_INPUT, HWMON_F_INPUT, + HWMON_F_INPUT, HWMON_F_INPUT, HWMON_F_INPUT, + HWMON_F_INPUT), + HWMON_CHANNEL_INFO(pwm, + HWMON_PWM_INPUT, HWMON_PWM_INPUT, HWMON_PWM_INPUT, + HWMON_PWM_INPUT, HWMON_PWM_INPUT, HWMON_PWM_INPUT, + HWMON_PWM_INPUT, HWMON_PWM_INPUT, HWMON_PWM_INPUT, + HWMON_PWM_INPUT), + NULL +}; + +static const struct hwmon_chip_info arctic_fan_chip_info =3D { + .ops =3D &arctic_fan_ops, + .info =3D arctic_fan_info, +}; + +static int arctic_fan_reset_resume(struct hid_device *hdev) +{ + struct arctic_fan_data *priv =3D hid_get_drvdata(hdev); + unsigned long flags; + + /* + * The device resets its PWM channels to hardware defaults on power + * loss during suspend. Clear the cached duty values so they reflect + * the unknown hardware state, consistent with probe-time behaviour + * (the device has no GET_REPORT support). Hold in_report_lock so + * this does not race with a concurrent pwm read or write callback. + */ + spin_lock_irqsave(&priv->in_report_lock, flags); + memset(priv->pwm_duty, 0, sizeof(priv->pwm_duty)); + spin_unlock_irqrestore(&priv->in_report_lock, flags); + return 0; +} + +static int arctic_fan_probe(struct hid_device *hdev, + const struct hid_device_id *id) +{ + struct arctic_fan_data *priv; + int ret; + + if (!hid_is_usb(hdev)) + return -ENODEV; + + ret =3D hid_parse(hdev); + if (ret) + return ret; + + priv =3D devm_kzalloc(&hdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->hdev =3D hdev; + spin_lock_init(&priv->in_report_lock); + init_completion(&priv->in_report_received); + hid_set_drvdata(hdev, priv); + + ret =3D hid_hw_start(hdev, HID_CONNECT_DRIVER); + if (ret) + return ret; + + ret =3D hid_hw_open(hdev); + if (ret) + goto out_stop; + + /* + * Start IO before registering with hwmon. If IO were started after + * hwmon registration, a sysfs write arriving in that narrow window + * would send an OUT report but the ACK could not be delivered (the HID + * core discards events until io_started), causing a spurious timeout. + */ + hid_device_io_start(hdev); + + /* + * Use the non-devm variant and store the pointer so remove() can + * call hwmon_device_unregister() before tearing down the HID + * transport. devm_hwmon_device_register_with_info() would defer + * unregistration until after remove() returns, leaving a window + * where a concurrent sysfs write could call hid_hw_output_report() + * on an already-stopped device (use-after-free). + */ + priv->hwmon_dev =3D hwmon_device_register_with_info(&hdev->dev, "arctic_f= an", + priv, &arctic_fan_chip_info, + NULL); + if (IS_ERR(priv->hwmon_dev)) { + ret =3D PTR_ERR(priv->hwmon_dev); + goto out_close; + } + + return 0; + +out_close: + hid_device_io_stop(hdev); + hid_hw_close(hdev); +out_stop: + hid_hw_stop(hdev); + return ret; +} + +static void arctic_fan_remove(struct hid_device *hdev) +{ + struct arctic_fan_data *priv =3D hid_get_drvdata(hdev); + + /* + * Unregister hwmon before stopping the HID transport. This removes + * the sysfs files and waits for any in-progress write() callback to + * return, so no hwmon op can call hid_hw_output_report() after + * hid_hw_stop() frees the underlying USB resources. + * Matches the pattern used by nzxt-smart2 and aquacomputer_d5next. + */ + hwmon_device_unregister(priv->hwmon_dev); + hid_device_io_stop(hdev); + hid_hw_close(hdev); + hid_hw_stop(hdev); +} + +static const struct hid_device_id arctic_fan_id_table[] =3D { + { HID_USB_DEVICE(ARCTIC_VID, ARCTIC_PID) }, + { } +}; +MODULE_DEVICE_TABLE(hid, arctic_fan_id_table); + +static struct hid_driver arctic_fan_driver =3D { + .name =3D "arctic_fan", + .id_table =3D arctic_fan_id_table, + .probe =3D arctic_fan_probe, + .remove =3D arctic_fan_remove, + .raw_event =3D arctic_fan_raw_event, + .reset_resume =3D arctic_fan_reset_resume, +}; + +module_hid_driver(arctic_fan_driver); + +MODULE_AUTHOR("Aureo Serrano de Souza "); +MODULE_DESCRIPTION("HID hwmon driver for ARCTIC Fan Controller"); +MODULE_LICENSE("GPL");