Add device tree bindings for RTD1319D.
Signed-off-by: Tzuyi Chang <tychang@realtek.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
v2 to v3 change:
1. Use '-pins$' to be node name pattern.
2. Remove if/then condition under the patternProperties
"-pins$".
v1 to v2 change:
1. Add a description for RTD1319D.
2. Rename realtek,pdrive, realtekmndrive and realtek,dcycle.
3. Add a description for PMOS and NMOS driving strength.
4. Remove the wildcard in the compatible strings.
5. Use '-pins$' to be node name pattern.
---
.../pinctrl/realtek,rtd1319d-pinctrl.yaml | 187 ++++++++++++++++++
1 file changed, 187 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/realtek,rtd1319d-pinctrl.yaml
diff --git a/Documentation/devicetree/bindings/pinctrl/realtek,rtd1319d-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/realtek,rtd1319d-pinctrl.yaml
new file mode 100644
index 000000000000..f07361d60acd
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/realtek,rtd1319d-pinctrl.yaml
@@ -0,0 +1,187 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2023 Realtek Semiconductor Corporation
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/realtek,rtd1319d-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Realtek DHC RTD1319D Pin Controller
+
+maintainers:
+ - TY Chang <tychang@realtek.com>
+
+description:
+ The Realtek DHC RTD1319D is a high-definition media processor SoC. The
+ RTD1319D pin controller is used to control pin function, pull up/down
+ resistor, drive strength, schmitt trigger and power source.
+
+properties:
+ compatible:
+ const: realtek,rtd1319d-pinctrl
+
+ reg:
+ maxItems: 1
+
+patternProperties:
+ '-pins$':
+ type: object
+ allOf:
+ - $ref: pincfg-node.yaml#
+ - $ref: pinmux-node.yaml#
+
+ properties:
+ pins:
+ items:
+ enum: [ gpio_0, gpio_1, gpio_2, gpio_3, gpio_4, gpio_5, gpio_6, gpio_7,
+ gpio_8, gpio_9, gpio_10, gpio_11, gpio_12, gpio_13, gpio_14,
+ gpio_15, gpio_16, gpio_17, gpio_18, gpio_19, gpio_20, gpio_21,
+ gpio_22, gpio_23, usb_cc2, gpio_25, gpio_26, gpio_27, gpio_28,
+ gpio_29, gpio_30, gpio_31, gpio_32, gpio_33, gpio_34, gpio_35,
+ hif_data, hif_en, hif_rdy, hif_clk, gpio_40, gpio_41, gpio_42,
+ gpio_43, gpio_44, gpio_45, gpio_46, gpio_47, gpio_48, gpio_49,
+ gpio_50, usb_cc1, gpio_52, gpio_53, ir_rx, ur0_rx, ur0_tx,
+ gpio_57, gpio_58, gpio_59, gpio_60, gpio_61, gpio_62, gpio_63,
+ gpio_64, emmc_rst_n, emmc_dd_sb, emmc_clk, emmc_cmd, emmc_data_0,
+ emmc_data_1, emmc_data_2, emmc_data_3, emmc_data_4, emmc_data_5,
+ emmc_data_6, emmc_data_7, dummy, gpio_78, gpio_79, gpio_80,
+ gpio_81, ur2_loc, gspi_loc, hi_width, sf_en, arm_trace_dbg_en,
+ ejtag_aucpu_loc, ejtag_acpu_loc, ejtag_vcpu_loc, ejtag_scpu_loc,
+ dmic_loc, ejtag_secpu_loc, vtc_dmic_loc, vtc_tdm_loc, vtc_i2si_loc,
+ tdm_ai_loc, ai_loc, spdif_loc, hif_en_loc, sc0_loc, sc1_loc,
+ scan_switch, wd_rset, boot_sel, reset_n, testmode ]
+
+ function:
+ enum: [ gpio, nf, emmc, tp0, tp1, sc0, sc0_data0, sc0_data1, sc0_data2,
+ sc1, sc1_data0, sc1_data1, sc1_data2, ao, gspi_loc0, gspi_loc1,
+ uart0, uart1, uart2_loc0, uart2_loc1, i2c0, i2c1, i2c3, i2c4,
+ i2c5, pcie1, sdio, etn_led, etn_phy, spi, pwm0_loc0, pwm0_loc1,
+ pwm1_loc0, pwm1_loc1, pwm2_loc0, pwm2_loc1, pwm3_loc0, pwm3_loc1,
+ qam_agc_if0, qam_agc_if1, spdif_optical_loc0, spdif_optical_loc1,
+ usb_cc1, usb_cc2, vfd, sd, dmic_loc0, dmic_loc1, ai_loc0, ai_loc1,
+ tdm_ai_loc0, tdm_ai_loc1, hi_loc0, hi_m, vtc_i2so, vtc_i2si_loc0,
+ vtc_i2si_loc1, vtc_dmic_loc0, vtc_dmic_loc1, vtc_tdm_loc0,
+ vtc_tdm_loc1, dc_fan, pll_test_loc0, pll_test_loc1, ir_rx,
+ uart2_disable, gspi_disable, hi_width_disable, hi_width_1bit,
+ sf_disable, sf_enable, scpu_ejtag_loc0, scpu_ejtag_loc1,
+ scpu_ejtag_loc2, acpu_ejtag_loc0, acpu_ejtag_loc1, acpu_ejtag_loc2,
+ vcpu_ejtag_loc0, vcpu_ejtag_loc1, vcpu_ejtag_loc2, secpu_ejtag_loc0,
+ secpu_ejtag_loc1, secpu_ejtag_loc2, aucpu_ejtag_loc0, aucpu_ejtag_loc1,
+ aucpu_ejtag_loc2, iso_tristate, dbg_out0, dbg_out1, standby_dbg,
+ spdif, arm_trace_debug_disable, arm_trace_debug_enable,
+ aucpu_ejtag_disable, acpu_ejtag_disable, vcpu_ejtag_disable,
+ scpu_ejtag_disable, secpu_ejtag_disable, vtc_dmic_loc_disable,
+ vtc_tdm_disable, vtc_i2si_disable, tdm_ai_disable, ai_disable,
+ spdif_disable, hif_disable, hif_enable, test_loop, pmic_pwrup ]
+
+ drive-strength:
+ enum: [4, 8]
+
+ bias-pull-down: true
+
+ bias-pull-up: true
+
+ bias-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ drive-push-pull: true
+
+ power-source:
+ description: |
+ Valid arguments are described as below:
+ 0: power supply of 1.8V
+ 1: power supply of 3.3V
+ enum: [0, 1]
+
+ realtek,drive-strength-p:
+ description: |
+ Some of pins can be driven using the P-MOS and N-MOS transistor to
+ achieve finer adjustments. The block-diagram representation is as
+ follows:
+ VDD
+ |
+ ||--+
+ +-----o|| P-MOS-FET
+ | ||--+
+ IN --+ +----- out
+ | ||--+
+ +------|| N-MOS-FET
+ ||--+
+ |
+ GND
+ The driving strength of the P-MOS/N-MOS transistors impacts the
+ waveform's rise/fall times. Greater driving strength results in
+ shorter rise/fall times. Each P-MOS and N-MOS transistor offers
+ 8 configurable levels (0 to 7), with higher values indicating
+ greater driving strength, contributing to achieving the desired
+ speed.
+
+ The realtek,drive-strength-p is used to control the driving strength
+ of the P-MOS output.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 7
+
+ realtek,drive-strength-n:
+ description: |
+ Similar to the realtek,drive-strength-p, the realtek,drive-strength-n
+ is used to control the driving strength of the N-MOS output.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 7
+
+ realtek,duty-cycle:
+ description: |
+ An integer describing the level to adjust output duty cycle, controlling
+ the proportion of positive and negative waveforms in nanoseconds.
+ Valid arguments are described as below:
+ 0: 0ns
+ 2: + 0.25ns
+ 3: + 0.5ns
+ 4: -0.25ns
+ 5: -0.5ns
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 0, 2, 3, 4, 5 ]
+
+ required:
+ - pins
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ pinctrl@4e000 {
+ compatible = "realtek,rtd1319d-pinctrl";
+ reg = <0x4e000 0x130>;
+
+ emmc-hs200-pins {
+ pins = "emmc_clk",
+ "emmc_cmd",
+ "emmc_data_0",
+ "emmc_data_1",
+ "emmc_data_2",
+ "emmc_data_3",
+ "emmc_data_4",
+ "emmc_data_5",
+ "emmc_data_6",
+ "emmc_data_7";
+ function = "emmc";
+ realtek,drive-strength-p = <0x2>;
+ realtek,drive-strength-n = <0x2>;
+ };
+
+ i2c-0-pins {
+ pins = "gpio_12",
+ "gpio_13";
+ function = "i2c0";
+ drive-strength = <4>;
+ };
+ };
--
2.42.0
On Tue, 19 Sep 2023 18:11:16 +0800, Tzuyi Chang wrote: > Add device tree bindings for RTD1319D. > > Signed-off-by: Tzuyi Chang <tychang@realtek.com> > Reviewed-by: Linus Walleij <linus.walleij@linaro.org> > --- > v2 to v3 change: > 1. Use '-pins$' to be node name pattern. > 2. Remove if/then condition under the patternProperties > "-pins$". > v1 to v2 change: > 1. Add a description for RTD1319D. > 2. Rename realtek,pdrive, realtekmndrive and realtek,dcycle. > 3. Add a description for PMOS and NMOS driving strength. > 4. Remove the wildcard in the compatible strings. > 5. Use '-pins$' to be node name pattern. > --- > .../pinctrl/realtek,rtd1319d-pinctrl.yaml | 187 ++++++++++++++++++ > 1 file changed, 187 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/realtek,rtd1319d-pinctrl.yaml > Reviewed-by: Rob Herring <robh@kernel.org>
© 2016 - 2024 Red Hat, Inc.